Loading…
Loading…
Updated dates
Tender Value
₹1.5 Cr
EMD Value
₹3 L
Closing Date
8 Jun 2026, 4:00 pm3d left
Executive Engineer REW Kargil
Executive Engineer REW Kargil
Construction of Public parks at various places in District Kargil Balance work SITC of GYM equipment
2026_RDD_18958_1
e-Tender- 06 of REW Kargil UTL of 2026-27
Open Tender
Civil Works - Others
Kargil
Please refer Tender documents.
4 documents required · 4 mandatory
₹1,500
Executive Engineer REW Kargil
₹3 L
18 May 2026
18 May 2026
10 Jun 2026
18 May 2026
8 Jun 2026
19 May 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount | Item Code |
|---|---|---|---|---|---|---|
| 1 | Air walker : Providing and fixing air walker with below Specification:
1. Dimensions (LxWxH): 1100x550x1480mm
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make .
3. ‘U’ shaped main frame of NB 65mm (G.I) ‘C’ class pipe .
4. All other pipes of NB 32mm (G.I) ‘C’ class (‘NB’ stands for nominal bore i.e , internal diameter pipe in millimeters)
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints .
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs .
7. Zinc primer paint is applied at all the welding points prior to finishing .
8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
9. Foothold made of nylon alloy with rounded edges to prevent impact and injury .
10. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
11. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
12. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
13. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
14. High tensile steel with galvanized nut bolts are used for assembly .
15. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
16. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 59,957.63 | ₹3,59,745.78 | 1 |
| 2 | SIT UP STATION :Providing and fixing sit-up station with below specification:
1. Dimensions (LxWxH): 1500x1150x650mm.
2. Fabricated with base frame of NB 50mm (G.I) ‘C’ class pipe of approved make .
3. Main frame of NB 32mm (G.I) ‘C’ class pipe.
4. Leg support of NB 65mm (G.I) ‘C’ class pipe (NB’ stands for normal bore i.e, internal diameter of pipe in millimeter).
5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness .
6. All pipe are powder coated using akzonobel or equivalent paint of 80-120 micron thick .
7. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
8. Zinc primer paint is applied at all the welding points prior to finishing.
9. The equipment to be fixed on ground with concrete of minimum strength M-25 and expansion bolts.
10. Once the concrete is set , the equipment is fixing on to it.
11. High tensile steel with galvanized nut bolts are used for assembly.
12. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment.
13. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 59,601.69 | ₹3,57,610.14 | 2 |
| 3 | AIR SWING : providing and fixing air swing in a pair with below specifications:
1. Dimensions (LxWxH): 1150x900x1250mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame of NB 50mm (G.I) ‘C’ class pipe.
4. Handle support frame of NB 40mm (G.I) ‘C’ class pipe . (NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters )
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips .
9. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
10. Foothold made of nylon alloy with rounded edges to prevent impact and injury .
11. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
13. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
14. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
15. High tensile steel with galvanized nut bolts are used for assembly .
16. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
17. Self – explanatory stainless steel label fixed on equipment for ease of | 6 | Nos | 83,686.44 | ₹5,02,118.64 | 3 |
| 4 | HORSE RIDER STATION:Providing and fixing horse rider station with below specification:
1. Dimensions (LxWxH): 1000x600x1100mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame of NB 65mm (G.I) ‘C’ class pipe.
4. Handle support frame of NB 50mm (G.I) ‘C’ class pipe . (NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters )
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
9. Foothold made of NB 25mm (G.I) ‘C’ class pipe .
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness , colored , UV resistant and environmental friendly.
11. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
13. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
14. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
15. High tensile steel with galvanized nut bolts are used for assembly .
16. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
17. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 70,338.98 | ₹4,22,033.88 | 4 |
| 5 | LEG PRESS: Providing and fixing leg press in a pair with below specification:
1. Dimensions (LxWxH): 1750x550x1600mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame of NB 50mm (G.I) ‘C’ class pipe..(NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters )
4. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
5. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
6. Zinc primer paint is applied at all the welding points prior to finishing.
7. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
8. Foothold made of NB 25mm (G.I) ‘C’ class pipe .
9. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness , colored , UV resistant and environmental friendly.
10. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
11. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
12. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
13. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
14. High tensile steel with galvanized nut bolts are used for assembly .
15. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
16. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 77,118.64 | ₹4,62,711.84 | 5 |
| 6 | PULL CHAIR : Providing and fixing pull chair in a pair with below specification:
1. Dimensions (LxWxH) : 1950x700x2000mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame of NB 50mm (G.I) ‘C’ class pipe.
4. Handle frame of NB 40mm (G.I) ‘C’ class pipe . (NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters )
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips .
9. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness , colored , UV resistant and environmental friendly.
11. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
13. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
14. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
15. High tensile steel with galvanized nut bolts are used for assembly .
16. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
17. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 87,500 | ₹5,25,000 | 6 |
| 7 | SEATED CHEST PRESS: Providing and fixing seated chest press in a pair with below specification :
1. Dimensions: (LxWxH) 1800x700x2000mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame of NB 50mm (G.I) ‘C’ class pipe.
4. Handle frame of NB 32mm (G.I) ‘C’ class pipe . (NB’ stands for nominal bore size i.e., internal diameter of pipe in millimeters )
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips .
9. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness , colored , UV resistant and environmental friendly.
11. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
13. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
14. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
15. High tensile steel with galvanized nut bolts are used for assembly .
16. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
17. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 95,762.71 | ₹5,74,576.26 | 7 |
| 8 | ARM WHEEL: Providing And fixing arm wheel in a pair with below specification :
1. Dimensions (LxWxH): 850x800x1800mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame wheel of NB 32mm (G.I) ‘C’ class pipe . (NB’ stands for nominal bore size i.e., internal diameter of pipe in millimeters )
4. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
5. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
6. Zinc primer paint is applied at all the welding points prior to finishing.
7. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
8. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness , colored , UV resistant and environmental friendly.
9. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
10. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
11. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
12. High tensile steel with galvanized nut bolts are used for assembly .
13. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
14. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 60,847.46 | ₹3,65,084.76 | 8 |
| 9 | ROWING MACHINE : Providing and fixing rowing machine with below specification:
1. Dimensions (LxWxH): 1280x800x1150mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Main frame of NB 65mm (G.I) ‘C’ class pipe.
4. Handle support frame of NB 25mm (G.I) ‘C’ class pipe . (NB’ stands for nominal bore size i.e., internal diameter of pipe in millimeters )
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
9. Foothold made of NB 65mm (G.I) ‘C’ class pipe .
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00mm thickness , colored , UV resistant and environmental friendly.
11. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
13. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
14. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
15. High tensile steel with galvanized nut bolts are used for assembly .
16. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
17. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 82,796.61 | ₹4,96,779.66 | 9 |
| 10 | DOUBLE CROSS WALKER : Providing and fixing double cross walker with below specifications:
1. Dimensions (LxWxH): 1600x600x1600mm.
2. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make.
3. Handle frame of NB 32mm and 25mm(G.I) ‘C’ class pipe . (NB’ stands for nominal bore size i.e., internal diameter of pipe in millimeters )
4. Foot support frame of 100x50x2.5mm CRC rectangular pipe .
5. All pipe are powder coated with 80-120 micron thick akzonobel or equivalent paints.
6. All joint of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness , UV resistant and colored.
9. Foothold made of nylon alloy with rounded edges to prevent impact and injury .
10. Maintenance free bearings of skf or equivalent make duly oil sealed and self – lubricated are used in the equipment manufactured .
11. The equipment are fitted with inbuilt limiters to prevent unwanted movements .
12. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness .
13. Once the concrete is set , the equipment is fixing on to it and nuts and bolts are covered with base plate cover .
14. High tensile steel with galvanized nut bolts are used for assembly .
15. Equipment made to EN16630 AND ASTM F 3101-15 and GS mark for international standard for outdoor fitness equipment .
16. Self – explanatory stainless steel label fixed on equipment for ease of use . | 6 | Nos | 80,084.75 | ₹4,80,508.5 | 10 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.75 MB
BOQ_45286.xls
BOQ • 0.36 MB
Download all tender documents and submit your bid