Special repair for renovation of Primary Health Centres at Pali Mohtabad Faridabad upgraded into ABHWC in Faridabad District Civil and PH Work REINVITED

Amount

Scraping- White wash and colour wash [HSR 8.32 (a)]

12 mm thick cement plaster 1:6 [HSR 15.7]

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. [HSR 16.60]

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on old work, one coat to give an even shade. [HSR 16.62]

Providing & applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get even and smooth finish including cost & carriage of all material, labour charges, scaffolding, sundries etc. complete(JK/Birla make) [HSR 16.81]

Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mittii including finishing [HSR 16.52]

Dismantling white or coloured glazed tiles (to be carefylly removed) [HSR 8.38]

Dismantling cement conglomerate/terrazzo floors 25 mm to 50 mm Thick including concrete base [HSR 8.25]

Conglomerate floor 40 mm thick cement concrete topping 1:2:4 [HSR 14.9]

Providing & fixing Ist quality ceramic glazed wall tiles confirming to IS 15622 (thickness to be specified by manufacturer) of approved make in all colours, shade except burgundy, bottle green, black of any size as approved by Engineer in charge in skirting risers of steps and dados over 12 mm thick bed of cement motar 1:3 coarse and jointed with grey cement slurry including pointing in white cement mixed with pigment of matching shades complete (b) Size of ceramic Glazed tiles 300mm X 450mm of manufacturer like : RAK, NITCO, KAJARIA, Simpolo & Orient Bell shall be used as approved by Engineer-in-Charge [HSR 14.92b] Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material- Ground Floor

Providing & fixing ceramic tiles/ anti skid tile of size 400mm X 400mm of approved make in floors laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles Note: The shall be of premium quality (First Quality) of reputed manufacturer like RAK, NITCO, KAJARIA, Simpolo & Orient Bell, Johnson [HSR 14.91]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUITE, SYPHONIC TYPE, Consisting of- VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge) Single trap symphonic W.C. Suite white [HSR 30.5(a)(i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE URINALS FLAT BACK OR ANGULAR LIPPED FRONT IN VITREOUS CHINA-WARE WITH 5 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC., COMPLETE AS FULLY DESCRIBED IN ITEM NO. 30.19 ABOVE. 465 mm high White [HSR 30.21i]

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid. White plastic seat (Solid) [HSR 30.13i]

EXTRA OVER AND ABOVE ITEM NOS. 30.19 TO 30.22 ABOVE FOR PROVIDING AND FIXING PER SET LEAD ‘P’ TRAP AND 32 MM LEAD WASTE PIPE WEIGHING 3.47 KG/METRE AND 2.8 MM THICK UPTO FLOOR LEVEL AND PLUMBER JOINT. [HSR 30.23]]

Providing and fixing 25 mm thick marble backs for the different type of urinals. VITREOUS CHINAWARE PARTITION PLATE small size 680x330 [HSR 30.40bi]

Providing and fixing in position Indian make (ordinary) lavatory suites consisting of lavatory in vitreous chinaware size as given below (to the approval of the engineer-in-charge) including china plug for tap hole where necessary; size 630 mm x 500 mm with one no. tap. [HSR 30.41v]

Providing and fixing 40 mm i/d GI waste pipe embedded in walls or lead waste pipe weighing 4.46 kg./meter and 3.0 mm thick up to floor level as required by the engineer-in-charge including cost of union and plumber joint [HSR 30.62]

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) [HSR 30.75] (a) bib cock Long body

(c) bib cock

Providing and fixing in position best Indian make flexible tube connection. (b) C.P. Brass (iii) 15mm x 450 mm. (HSR 30.82 (b) (iii)).

Providing & fixing CP angle valve with flange G4753 A1 Parryware make complete in all respect as per directions of Engineer-in-Charage

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (HSR 30.119). 700 Ltrs. Capacity Water Tank

Cement concrete 1:1½:3 with stone aggregate 20mm nominal size for reinforced concrete work in footing, strips, foundation, rafts, pedestal and approach slabs of bridges etc. but excluding steel reinforcement and including centring and shuttering, laid in position, complete in all respects. (for work upto 1.5 Mtrs. below ground level). [HSR. 10.90 + 10.95 (a)].

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres [HSR 6.6]

First class brick work laid in cement sand mortar 1:6 in foundation and plinth. [HSR 11.2]

12 mm thick cement plaster 1:6 [HSR 15.7]

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, or approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame door and window frame of[HSR 18.34] (b) Size 76 mm X 38 mm with 35 mm wide single rebate

(C)door and window frame size 114 mm X 50 mm with 35 mm wide double rebate

Supplying and fixing glass panes including special metal sash putty of approved make glass panes 4 mm thick, exceeding 40 sq dm areas.[HSR 18.30b]

Removing door and windows (wood and steel) with chowkats by making Recesses in walls when the wall is not to be dismantled:- [HSR 8.18](a) doors

Wire gauze of 140 G or 120 G designation fixed on steel windows of standard rolled steel section, with 3 mm thick flat iron cover moulding of 12/5 mm width, fixed with machine, screws welded complete in all respects [HSR 18.32]

Applying priming coat with metal primer on New steel or iron work including preparation of surface. [HSR 16.9]

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. [HSR 16.3]

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. [HSR 18.12]

Providing and fixing poly carbonate sheet 1.25mm thuckness on gates and grills excluding the cost of MS framework but including the cost of nut bolt, welding rods complete in respect as per direction of Engineer-in-Charge. [HSR 18.43]

Providing & fixing aluminium work for door & window, ventilators and partition with extruded built up stendard tubuler section / appropriate Z section and other section of approved make conforming to IS, 733 and IS : 1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasterner including necessary filling up of gap at jumction, at top, bottom & side with required neopreme felt etc. aluminium section shall be smooth, rust free straight mitred and jointed mechancally wherever required including cleat angle. Aluminium snap beading for glazing/panclling CP brass/stainless steel screw, etc. complete. Shutter of door, window & ventilators including providing & fixing hinges/ pivots and making provision for fixing of fitting wherever required including the cost of PVC/neo preme gasket required including aluminium fitting [HSR 17.96]

Cost of aluminium fitting cokmplte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt)- for double lead shutter [HSR 17.72b]

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. [HSR 14.1]

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO (Double charged tiles shall be used as approved by Engineer in charge. (NS). Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.(NS)

Providing & fixing in position Marilyn looking mirror of size 600x 450mm of Parry ware make complete in all respect as per the directions of Engineer-in-Charge

Recovery Items:- Bidder have to quote rate for recovery items at least or more than reserve price. The rate quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency T Note:- The reserve rate/amount is minimum amount to be used as base for quoted purchase rate by the agency. No. rates/amount below the reserve price will be entertained and reserve price will be considered for all purpose in case the agency quotes lesser than reserve price_ Door @ 150/- Each