LIS Chorottur

Amount

Appendix

2.32:Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

15.56:Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.13.1:9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

OD7385/2022-2023:Providing and fixing C.I foot valves 250mm diameter complete with bolts, nuts, rubber insertions, etc as per direction of Engineer in charge

OD23144/2022-2023:Lifting the motor 26 HP to 50HP after disconnecting the wire connection, decoupling the pump, detatching from the base plate, starters, TP switches etc. using chain block, rope, chain

OD23195/2022-2023:Dismantling the 26-39 HP motor into stator and rotor, cleaning the windings, attending minor repairs, re taping the coils if necessary, varnishing the coils with best quality insulation varnish, cleaning and greasing the bearings with good quality grease, heating the windings, reassembling, test running including scrapping, cleaning, and painting with enamel paint.

OD23201/2022-2023:Lowering and Refitting the 30-59 HP motor on base plate, levelling and correcting allignment with the pump coupling the same giving connection, testing and trial run on full load

OD23280/2022-2023:Supplying and fitting starter of 5HP priming pump

OD23294/2022-2023:Supplying and engaging Assistant Wireman for servicing 30 HP starter

OD23297/2022-2023:Supplyng and engaging electrician for servicing 30 HP starter

OD23298/2022-2023:Supplying and engaging fitter for overhauling the pump

OD23299/2022-2023:Supplying bearings for proper working of the pump and motor

v.abdul salim

Bidder Name

kunhahammed v

v.abdul salim