ADDN ALTERATION CUM SPL REP TO BLDG NO P 06 AT RANIKHET UNDER GE RANIKHET

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.complete all as directed.

M&l for Dismatling timber scantling 40 sqcm and above in any position ,unframed work complete all as specified and directed

Dismantling of boarding , any description fixed in any position like wall ,wooden flooring and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for. (reinforcement cut as required to facilitate demolition)

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness.(below or above ground level) Complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m Complete all as specified and directed.

Demolition brick work or stone/ boulder masonery built in cement mortar including all quoins , pillars etc

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each.& removing to or from store all as specifed & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each.& removing to or from store all as specifed & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store.

Dismatling PVC Water tank Exc 250 & n exc 500 ltr and removing from site as specified and directed

Dismantaling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

M & L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishescomplete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square /rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles incl screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes.

M & L for glazed ceramic coloured / printed tiles 300mm x 450mm, 6 to 7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles, incl rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and as directed.

M & L Black Granite (of any type) tiles 20 mm thick machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishig types in cooking platforms and like Complete all as specified and directed.

M&L for parquet flooring hard board plank both side laminated with decorative surface and laid above and including thermoplastic sheet complete all as specified and directed

M&L 2nd class hard wood as in scantling clean sawn as in floor/roof/truss/purlin of any description in framed work complete all as specified and directed.

S & F Second class hardwood 25 mm boarding plain one side with butt joint fixed with nails in any situation. Complete all as specified and directed.

Fixing only second class hardwood boarding of any thickness complete all as specified and directed . ( Note :- Old boarding shall be obtaind from item No -03 above)

M & L Type B1 1:2:4 (20mm graded aggregate)for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Formwork to rough finished surface of concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)

M & L for TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement Complete all as specified and directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete al as specified

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete all as specified and directed.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls by adding 17-19% of potable water by weight of material for thickness above 15mm it is recommended to be applied in multiple layers. ready mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the compressive strength @ 28 days 10-12 Mpa/Bulk density 1500-1600 Kg/m3. (Note : The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 Mtr ht all as specified and directed)

M/L for preparing newly plastered wall surfaces and applying two coat of distemper oil emulsion over a coat of primer(Priming the plastered and other surface preparatory to distempering) incl 3 mm thick applying a layer of JK/ Birla putty on wall surfaces including cornics etc for proper levelling of plaster complete all as specified and directed.

M/L for complete removal of existing treatment for preparing old painted surfacess and applying two coat of distemper oil emulsion over a coat of primer incl 3 mm thick applying a layer of JK/ Birla putty on wall surfaces including cornics etc for proper levelling of plaster complete all as specified and directed.

Material & Labour for prepration of surfaces for New plastered or unplastered surfaces and applying Two or more coats of 100% remium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces

Material & Labour for complete removal of existing treatment and applying Two or more coats of 100% remium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered surfaces of ceilings and applying two coats of white wash incl complete removal of old plastered surfaces.

M&L for Pressed steel frames 105X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,supplied and fixed complete all as specified and directed.

M&L for Pressed steel frames 125X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,supplied and fixed complete all as specified and directed.

Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F three track aluminum powder coated sliding window with three sliding shutter , the size of outer frame three track 100 x 37x 1.50mm ( using two track for glazed window shutter and one track for wire gauged ) , the section shutter size 37x 18x 1.2mm)and glazing with 5 mm thick Transparency glass of poly carbone including all-around suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including all necessary fittings

S&F factory made flush shutters 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed

S & F factory made 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., rs, edges of framing plain, chamfered complete all as specified and directed.

Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately.

S & F 150 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed.

S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate 140 mm all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

Supply and fix Continuous (piano) hinges width 30 mm mild steel , bright finish or eletrogalvanised complete all as specified

S&F 18mm thick MDF Board both side finished as in wardrobe/ cup board shutter all as specified and as directed by Engineer-in-Charge.

S&F 25mm thick MDF Board both side finished as in cupboard shelves/ kitchen cabinet and as directed by Engineer-in-Charge.

S & F MS framed work such as grills, gratings, etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 190-0 or Fe-165-0.

M & L for Old painted surface to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coats of synthetic enamel including preparation of surfaces complete all as specified and directed.

M & L for newly painting to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

S & F in Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless steel wire staples.

Cutting chases, for water tubing or concealed , etc, and making good to facings where required and plastering in cement mortar (1:4) cutting not exceeding 10cm girth in brick walls complete all as specified and directed.

S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

Refixing of old 15 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.)

S&F GI water tubing of 20 mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

Refixing of old 20 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc complete all as specified and directed.

S&F in repairs stop valves,/angle valve cast copper alloy, fancy type chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe.

S&F in repairs stop valves cast copper alloy, fancy type chromium plated with long shank & cup (concealed) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe.

S & F vitreous china wash basin, white, flat back, size 620X480X185 mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs. Make i ( Jaquar cat Part No:- FNS-WHT-40801 ii ( Cera cat Part No :- 1067 A or Hindware Equalant.

S & F in repairs 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. Make i ( Jaquar cat Part No:- COP -001BPM ii ( Marc cat Part No :- MFX- 2010 or Cera Equalant.

S & F 15 mm bore Fancy type chromium plated Wall Mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs and wall flanges, screwed down high pressure with or without lettered hot and cold screwed for iron pipe complete all as specified and directed. Make i ( Jaquar cat Part No:- FUS- 29281 ii ( Marc cat Part No :- MDM - 2350 or Cera Equalant.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S & F in repairs bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified. Make i ( Jaquar cat Part No:- KUP- 35037 PM ii ( Marc cat Part No :- MFX - 2170 or Cera Equalant.

S& F in repair Vitreous china premium/ 1st quality wash down water closet EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified. Cera Cat NO S1053121

S & F in repairs 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe complete all as specified and as directed. Make i ( Cera cat Part No:- CIRIL-2617 ii ( HIndware or Parryware Equalant.

S&F Prayag hanging system and clamps support and holes with screws and back support rectangular mirror cabinet 400 X 500 (Cat No. 554) and fixed to plug with screws and cup washers complete all as apecified & directed

M & L for 32mm bore high density polyethylene pipes (HDPE) complete all as specified and directed.

M&L for sunken floor treatment as described as under (i) to (vii) :- (i) Demolition of cement concrete of any description and in any position not otherwise specifically provided or in any type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii|) M&L to fill the sunken floor with PCC ( 1:5:10) type E-2 using bk aggregate over the treated surface complete all as specified and directed. (iii) M& L 40mm thick (Min) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacturer instructions on bottom of sunken portion with proper slope towards spout. Vertical sides shall be plastered in CM (1:3) 15 mm thick mixed with water proofing compound as per manufacturer instructions. Plaster shall be extended over PCC coving when the same is green i.e. PCC & plaster be carried out at the same time complete all as specified and directed. (iv) After laying sewage/ plumbing pipes with fixtures in position 2 coats of OMIPLAS EP-101 epoxy compound shall be applied complete all as specified and directed.(v) Spouts of 25mm dia GI pipe light grade projecting 450mm clear of face outer a wall with mosquito proof cap on inner face of pipe shall be provided to drain out seepage water ,including cutting holes and making good if needed as specified and directed.(vi) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defects complete all as specified and directed.The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D; type, 60 cm long between flanges complete all as specified and directed. Make i ( Jaquar cat Part No:- ACN 11815 ii ( Marc or Cera Equalant.

S&F in repair chromium plated Soap disk fixed to plug with chormium plated brass screws all as specified and directed. Make i ( Jaquar cat Part No:- ACN-1131N ii ( Marc or Cera Equalant.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs Chromium plated shower rose 125 mm swivel type Make i ( Jaquar cat Part No:- OHS-35495 ii ( Marc cat Part No :- MSR - 1170N or Cera Equalant.

S & F in repair 20mm Dia Aluminium alloy anodised curtain rod decorative fency type with brackets complete all as specified.

S & F in repair PVC connections 15mm dia , 450mm long, , with PTMT nuts & washers at both ends

S & F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S & F in repairs Stainless steel wall mounted plate rack of size 780mm x760mm x 240mm, thickness of sheet not less than 1.0 mm and weight not less than 7.50 kg of approved design/pattern (as approved by Engr-in-charge) with provision for keeping plate and other crockery, fixed with screw and rawl plugs etc on wall complete Make as approved by GE

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete, fixed in repair.

S&F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints laid in trenches or floor complete.

S&F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete.

S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete.

S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints laid in trenches or floor etc complete.

S&F in repair PVC (SWR) bends 110mm dia any radius

S&F PVC in repair (SWR) bends 75 mm dia any radius

S&F PVC in repair (SWR) junction single,(Single T) 110mm dia equal or unequal with access door

S&F PVC in repair (SWR) junction single,(Single T) 75mm dia equal or unequal with access door

S&F PVC in repair(SWR)vent cowl 110mm bore

S & F Rotational moulded PVC water storage tanks 500 Ltrs capcity three layer (cylindrical vertical with closed top) hoissted and fixed in position all as specified

S & F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F Pre-painted galvaLume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed.

S & F for Aluminium anodised snap grid frame work for false ceiling comprising of following section for making partitions of 605 X 605 mm size fixed to walls with rawl plugs and screws and hang to roof with s 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners12.5mm dia. 40mm long complete all as specified. size of main tee shall be :- (i)36.5mmx25mmx1.4mm thick, Weighing 0.24Kg/Rm (ii)Cross Tee 23.5mmx36.4mmx1.4mm thick Weighing 0.191 Kg/Rm and (iii)Wall angle 40mmx25mmx2mm thick. Weighing 0.36 Kg/Rm

S & F 4 mm thick non asbestos fiber designer ceiling (E-board classic) board / tiles for insulation and accoustic purpose, 600 X 600 mm size fixed as in ceiling with and including dusting of surface complete all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 finished fair and even as in sub base Complete all as specified and directed.

Removing Excavated soil exceeding 250 M but not exceeding 500M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade

Sand filling under floors or in foundations including watering and consolidation

M & L for providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in coping, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in Hard/ Dense soil complete all as specified and directed.

Demolation and breaking up drain pipes 150 mm (salts glazed ware ,AC or Reinforced concrete) set in cement mortar all as specified

M & L DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid in trenches and jointed as required complete all as specified and directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

M & L providing precast cement concrete 1:2:4 type B1(20mm graded aggregate) as in cover slab for manholes, landing etc. setting in cement mortar 1:6 complete all as specified and directed.

S & F M.S. TMT bars 10mmdia and over, cut to length,bent in shape required, including cranking bending hooks ends and binding with M.S.wire(annealed) not less then 0.9mm dia complete all specified & directed.

M&L for Cement concrete 1:2:4 in haunching and benching for manholes complete all as specified and directed

Construction of brick masonary septic tank 25 users capacity with excavation and earth work in hard/dense soil or in soft/ distegrated rocks, PCC 1:2:4 type B-2 as in foundation, brick work in CM 1:4, RCC M-25, CI manhole cover (HD), vent, shaft and sludge chamber etc complete all as specified and directed

Construction of Brick masonary Soakage well of 3.60 m internal dia and 3.0 m effective depth and excavation & earth work in hard/dense soil or soft disintegrated rock in PCC 1:3:6 type C-2 as in foundation, honey combed and solid brick work in CM 1:4, RCC M-25 cover slab, PCC 1:2:4 in bands, filling with brick bats complete all as specified and directed

Surface channel in concrete 1:2:4 (20 mm graded aggregate) for drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as specified and directed. concrete, using ex- tra cement, including forms, moulds, mi-tred/stopped ends etc.All as specified and directed.

M&L cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation,filling,and mass concrete complete all as specified and directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:4) complete al as specified

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

Taking down carefully Aluminium/copper wiring of any size (for light, fan, socket or power etc complete) ( fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc to be measured and paid separately) and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed.

M & L point wiring for Modular fittings for one light point/ fan/ bell/ 5Amps socket out let (independent)point controlled by one, one way switch with 1.5 sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FR-LSH) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia )with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) incl modular metal flush box for mounting modular fittings and covered with modular cover plate with frame and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed One light/One fan/one bell point controlled by one modular switch

One light point controlled by Two way modular switch.

One modular socket outlet 3 pin 6 amps controlled by one switch on same board.

One modular socket outlet 3 pin 6 amps controlled by one switch on independent board.

All as per item No 2 herein before but wiring with 2.5 sqmm copper wire (FRLS) PVC and 2.5 sqmm earth wire for modular socket outlet 5 pin 16 amps on independent board.

Supply and fix modular type switch single pole, one way 6 Amp complete all as specified and directed.

S&F modular switch, 2 way 6 Amp 1 module complete all as specified and directed.

Supply and fix socket out let multi 5 pin, 6 Amps, modular type complete all as specified and directed.

Supply and fix switch modular type single pole, one way 16 Amp complete all as specified and directed.

Supply and fix socket out let 2 in1,3 pin, 6 and 16 Amp, modular type complete all as specified and directed.

S&F ceiling rose, PVC/ Poly carbonate,isolated body three terminal complete all as specified and directed.

S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

Supply and fix in replacement High quality LED T8 indoor batten tube light 20 Watt with aluminium extrusion in D shaped have large diameter for increased convection heat transfer incl one LED PC tube rod and driver, internaly pre wired of 1.5 sqmm twin twisted flexible cable all as specified & directed. NOTE: The contractor must submit 5 years warranty for LED fitiings.

Taking down unservicable MCB and S&F MCB SP, 240 volts,AC C curve, 10 KA 6 to 32 Amps .

Taking down unservicable MCB and S&F MCB SPN , 240 volts,AC B curve, 10 KA 40 Amps.

Taking down unservicable MCB and S&F MCB DP , 240 volts,AC C curve, 10 KA 40 Amps.

Taking down unserviceable MCB S & F MCB TPN , 415 volts, AC C curve, 10 KA 100 Amps.

S&F in replacement sheet metal enclosure in replacement single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 240 Volts 20 Amps including one 15 Amp switch on existing board with wiring for switching geyser on/off complete all as specified and directed.

Supply & Fix in replacement of non metallic PVC conduit 25 mm exclusive of boxes but includinf of all tees,bends,elbows, reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles, pipe hooks etc. concealed in wall ceiling floor etc for television/DTH/telephone/Data cable complete all as specified and directed.

S& F socket outlet for TV/Video/audio device modular type with inner and outer modular plate type, specially built for wall/high mounted TV and inc pressed steel/metal flush box concealed complete all as specified and directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete. all as specified and directed .NOTE : The contractor must submit 5 years warranty for LED fittings

Taking down unservicable DB and S&F sheet metal enclusure for DBs(double door type) single pole and neutral 12 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

S&F in replacement sheet metal enclusure for DBs(double door type) Triple pole and neutral 4 way including blacking platge as required with 200 Amps rated bus bar, 415 volts fixed complete all as specified and directed .

S & F in replacement LED bulk head fitting, 1 x 10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fittings

Taking out old U/S Sub main wiring for replacement including S&F sub main wiring with two single core( FR-LSH) PVC insulated and sheathed 1100 Volts grade, 6 Sqmm size cables, PVC insulated stranded copper conductor fixed in PVC conduite pipe 25mm dia with all accessories and one continuous run of 6.0 Sqmm copper conductor PVC complete all as specified and directed (Note :- Two single core cables along with earth wire and conduit shall be measured as one unit length).

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost.

S & F in replacement call bell ding dong AC, 230V single pole fixed over with and including sunk spressed steel box of size 175mmx100mm with 3mm thick plastic laminated backalite shut cover fixed with brass screw complete all as specified and directed,

S&F modular bell push, 6 Amp 1 module complete all as specified and directed.

S& F LED Bulb of 9 watt as specified .NOTE: The contractor must submit 5 years warranty for LED fittings

Supply and fix in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with two core flexible copper conductor cable of suitable size complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fittings

Taking down storage type water heater (geyser) of any type /make up to 50 Ltr capacity after disconnecting electric / water connections and refixing the same after carrying out necessary repairs including reconnecting the electric / water connections and testing complete all as specified and diected.

S & F in replacement Exhaust fan plastic body heavy duty ISI mark, 250 mm size with louvers including all connecting accessories and cutting opening on wall and making good as per existing surface complete all as specified and directed

S&F in replacement Exhaust fan metallic bady ISI mark, 300 mm size with louvers including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 300 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed.

Supply, laying and testing in replacement cable XLPE in replacement Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 core complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of underground cable and getting out in any type of soil complete all as directed by the Engineer-in-Charge

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cms. thick in soft / loose soil complete all as specified and directed by Engr -in -charge .

Removal of surplus soil not exceeding 50 Mtr and depositing where directs at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning in trenches spreading and consolidation 8cm thick before laying the cable & 15 cm of sand after laying the cable complete all as specified and directed.

M&L for laying of bricks well burnt sub class ‘B’ (old pattern) laid flat for cable protection width equal to the lengrth of brick complete all as specified and directed.

M & L galvanised steel water tubing 'light grade' 40 mm bore with all fittings laid under the roads, drains, culverts and fixed on poles etc complete all as specified and directed .

Please Enable Macros to View BoQ information