WELCOME MAINTENANCE AND MISC B and R REPAIR TO SMQ AT SECTOR 31 B and 31 C AT AF STN CHANDIGARH

Amount

Note :The unit rate quoted by the tenderer under Col No (13) of Sch `A’ (BOQ) unless specifically mentioned otherwise such as labour only/fixing only, for all items of works shall be deemed to be including cost of all materials, labour, tools and plants, testing and commissioning of work in position complete as required for entire completion of work.

Plain cement concrete ,25 mm thick (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in sub base finished even & rough to receive the bedding mortar in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete ,40 mm thick (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in flooring finished even & smooth using extra cement @1.20 Kg /Sqm in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Notes :(i) Use and waste of form work/screed strips and to divide the area in panels shall be included in the quoted rate . (ii) Where dividing strips are used, these shall be measured and paid separately,

Glass dividing strips, 3 mm thick and 38mm wide, as in floors fixed in position , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 75 mm thick, 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and fair in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note :Quoted rates are inclusive of use and waste of formwork and to devide the area in panels.

Plain cement concrete 75 mm thick, (1:4:8), type D-2, using 40 mm graded mechanically crushed stone aggregates as in sub base ,foundations, filling and mass concrete/Plinth protection in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Cutting opening through brick wall built in cement mortar for window type AC of standard size, forming jambs etc. to opening, making good under cills or over lintels, 2nd class hard wood, plain, fillets, square or rectangular in section, clean swan, sectional area exceeding 13 Sq.cm but not exceeding 25 Sq.cm, including painting & distempering to match existing and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Cutting holes in brick walls exc half brick but n exc full brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required to match existing and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note: Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall

Brick work with sub-class `B' bricks Fly ash bricks (bricks shall be burnt clay fly ash building bricks as per IS- 13757), straight or curved on plan exceeding 6 M mean radius built in cement sand mortar 1:4 complete in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc for the area where unservicable bricks retrived and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Notes: (i) Servicable bricks retrived from demolition of this item shall be used after proper cleaning and washing of old bricks under item No.09 below. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius (except bricks) built in cement sand mortar 1:4 complete in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc for area where servicable bricks retrived and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes: (i) Servicable bricks retrived from demolition of item No.08 and this item shall be used under this item after proper cleaning and washing of old bricks. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

First quality glazed ( digital glossy finish) ceramic coloured tiles of 350x450x 7 to 8 mm thick laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes :- (i) Design, pattern and colour of tiles will be as approved by GE. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes :- (i) Design, pattern and colour of tiles will be as approved by GE. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

Vitrified ceramic tiles (light Shade) 9 to 10 mm thick (square/ractangular) coloured polished tiles, area of each tile not exceeding 0.36 sqm in floors etc. laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Vitrified ceramic tiles (light Shade) 9 to 10mm thick (square/ractangular) coloured polished tiles, area of each tile not exceeding 0.36 sqmas skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises, complete all as specified and directed by the Engineer in Charge.

Machine cut kota stone slab flooring of 17-18 mm thick laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and complete and 15mm thick screed bed in CM 1:6 in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Granite (of any type ) 16-18 mm thick, work (table rubbed and polished) fine grained 'Z' black/red in cooking platforms including moulding and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15 mm thick in CM 1:3 in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Providing and laying 60mm thick factory made machine pressed interlocking paver block of M-35 grade of any shape and size confirming to IS 15658-2006 with grey cement and pigment (In top layer) laid over and including 25 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Note : Quoted rates are inclusive of fine sand and nothing extra shall be admissible on this account.

Coloured chequered cement concrete tiles 300mm x 300mm x 25mm or 400 mm X400 X25 mm thick, factory made, ISI marked (IS 13801-1993), with grey cement & pigment, laid with neat cement slurry @ 3Kg/Sqm over & including 20mm thick screed bed of cement mortar (1:6), pointed in white cement with matching colour pigment in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment,complete all as specified and directed by Engineer-in- Charge.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished the surfaces even and smooth without using extra cement and mixing with water proofing compound as per manufacturers instruction @3% of cement weight in and including taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note: Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account.

Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & bittom of chajjas, beams, balcony ceiling ,roof slab ceiling etc.) finished the surfcae even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. Notes for item No. 18 to 20: (i).Quoted rate shall be deemed to include for necessary scaffolding & formwork for building upto 12.00m high. (ii) No extra payment made to contractor for work in small patches as required at site/as directed. (iii) All safety measures for the safety of workers shall be ensured by contractor before execution of work. Insurance of workers shall be got done by contractor before execution of the work and the cost for the same shall be deemed to be included in rate quoted by contractor.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing , complete all as specified and directed by Engineer-in-Charge.

Preperation of newly plastered surfaces of walls and applying two coats of cement base paint ,complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over 1mm thick wall care putty to smoothening the surface by using sand paper , complete all as specified and directed by Engineer-in-Charge.

Preparation of newly plastered surfaces of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489: 2004, alkali & fungal resistant, dirt resistant exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces , complete all as specified and directed by Engineer-in-Charge. Note: Weather proof exterior emulsion paint and primer shall be of same manufacturer.

Preparation of old surfaces of walls including brooming down or steel wire brushing, scraping down smoke soot, moulds, mooss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with cement wall care putty and applying one coat of white wash , complete all as specified and directed by Engineer-in-Charge.

Preparation of old surfaces of ceiling including brooming down or steel wire brushing, scraping down smoke soot, moulds, mooss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with cement wall care putty and applying one coat of white wash, complete all as specified and directed by Engineer-in-Charge.

Preperation of old surfaces of walls including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; etc and filling the cracks/holes with cement wall care putty and applying one coat of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Preperation of old surfaces of ceiling including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; etc and filling the cracks/holes with cement wall care putty and applying one coat of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of brick /stone /plastered surfaces of walls including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; washing, rubbing down and stopping of surfaces using sand paper and applying two coat of oil bound distemper including 1mm thick Walll care putty and smoothing the surface, complete all as specified and directed by Engineer-in-Charge.

Preparation of old painted wooden surfaces over 10cm width or grith not otherwise described and applying one coat synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge

Preparation of old painted steel or Iron surfaces over 10cm width or grith not otherwise described and applying one coat synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. Note For Ser Item No. 24 to 31:- The rates quoted against those items shall being to be included for the use of scafolding, ladders, cradles etc, up to triple storey building, removing nails, making good holes, cracks etc removing furnitures, cub boards, washing floors, floor and wall tiles,cleaning glasses, joinerys, electric fittings, wiring, conduits etc of drops, splashes and living premises clean and tidy upto entire satisfaction of Engineer-in-Charge,

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exceeding 1.00 Sq. m but not exceeding 2.00 Sq. m each and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Repairing of wooden/steel shutters after easing and adjusting, replacing of builders hardware and screws including welding/cutting/chesing as required of any description n.exc 1 sq. m each and refixing in the same opening ,complete all as specified and directed by Engineer-in-Charge. Note:- work to be executed in pieces or petty repairs as per site requirements.

Repairing of wooden/steel shutters after easing and adjusting, replacing of builders hardware and screws including welding/cutting/chesing as required of any description exc 1 sq. m and not exc 2 sqm each and refixing in the same opening ,complete all as specified and directed by Engineer-in-Charge. Note:- work to be executed in pieces or petty repairs as per site requirements.

Taking down old aluminum door and refixing in same opening after reparing to damaged/loosened aluminum rail sections, tightening of scerws,reparing/replacement of locking arragment, repair /replacement of glass beading,repair/replacement of roller etc making door in servicealbe condition ,complete all as specified and directed by Engineer-in-Charge.

Taking down old rolling shutter and refixing in the same position to existing rolling shutters after repair/replacement of roller springs, locking device,laths etc if required as per site including necessary cleaning, welding, oiling greasing ,complete all as specified and directed by Engineer-in-Charge.

Pressed steel frames of size 105 x 60 mm , made out of 1.25mm thick sheet for doors with one or more rebates , including necessary fixing lugs, hinges (mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked), lock strike plate, etc., with and including back filling PCC (1:3:6), type C-0,complete all as specified and directed by the Engineer in Charge. Note :Cost of filling hollow of frame with plain cement concrete shall be included in the quoted rate and nothing extra shall be admissible on this account .

Pressed steel frames of size 125 x 60 mm, made out of 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges (mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked), lock strike plate, etc., with and including back filling PCC (1:3:6), type C-0,complete all as specified and directed by the Engineer in Charge. Note :Cost of filling hollow of frame with plain cement concrete shall be included in the quoted rate and nothing extra shall be admissible on this account .

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted as per specification & drawing and as per manufacturer's instructions and shown on drawing in section 8 on Page 178 of SSR Pt-II ,complete all as specified and directed by the Engineer in Charge.

Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for style and plain colour PVC sheets for top rail, lock rail and bottom rail on either sides & as gap insert for top- rail and bottom rails. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing ,complete all as specified and directed by Engineer-in- Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for Chowkhat/doors shutter, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings,complete all as specified and directed by Engineer-in- Charge.

Factory made box type steel window with two nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-184-2012 Sheets 1/3 & 3/3 and as directed by the Engineer in Charge.

Factory made made box type steel window with two Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars, including flat iron 12 x 3 mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-185-2012 Sheets 1/2 & 2/2 and as directed by the Engineer in Charge.

Factory made box type steel ventilator fixed type, dovetailed or welded and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.

Factory made made box type steel ventilator with glazed shutter or gauzed shutter with glazing bars or flat iron 12 x 3mm dovetailed or welded for fixing wire mesh/glass and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.

Factory made 35 mm thick (Batten thickness) 2nd class hard wood plain, framed, paneled shutters( two number No of panels) with panels of timber flat on both sides (feather edges) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated and detapering from 5 mm to 10 mm around the panel on one side fitted to chowkat, complete all as specified and directed by the Engineer in Charge.

30 mm thick (Batten thickness) Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats,complete all as specified and directed by the Engineer in Charge.

30 mm thick Flush shutters ,solid core construction with particle board core and plywood face panels commercial type on both sides, duly provided with 6mm thick Teakwood leeping on edges alround, fitted to chowkats, , complete all as specified and as directed by Engineer-in- Charge.

Butt hinges 100 mm size ,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 ISI marked ,complete all as specified and directed by the Engineer in Charge.

Butt hinges 100 mm size ,heavy weight, cold rolled mild steel, and fixed ISI marked fixed as in repair,complete all as specified and directed by the Engineer in Charge.

Barrel tower bolts aluminum anodizes of extuded section and fixed of 150 mm long size (length of bolt), complete all as specified and directed by Engineer-in-Charge

Barrel tower bolts aluminum anodizes of extuded section and fixed of 150 mm long size (length of bolt) fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Handles 'D' type of size 100 mm ,extruded aluminium alloy , fabricated type anodized ,complete all as specified and directed by Engineer-in- Charge.

Handles 'D' type of size 150 mm ,extruded aluminium alloy , fabricated type anodized ,complete all as specified and directed by Engineer-in- Charge.

Handles 'D' type of size 150 mm ,extruded aluminium alloy , fabricated type anodized fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Aluminum alloy, anodized, sliding door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 300mm, bolts not less than 12mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ) , complete all as specified and directed by Engineer-in-Charge.

Aluminum alloy, anodized, sliding door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 250 mm, bolts not less than 12mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ) fixed as in repair, complete all as specified and directed by Engineer-in-Charge

Plain fillets square, rectangular or triangular in section, 2nd class hardwood of sectional area exc 13 & n exc 25 sqcm, clean sawn, wrought finished secured with screws in and including dismantling of old plain fillets ,complete all as specified and directed by Engineer-in- Charge.

Prelaminated particle board 18 mm /19 mm thick ,interior grade, prelaminated both sides with decorative choice lamination for wooden and fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around in and including dismantling of old board ,complete all as specified and directed by Engineer-in- Charge.

Continuous (Piano) hinges, width of flaps (when open ) 30mm, stainless steel bright finish or electro galvanised, ISI Marked fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Hasp & staple of 100mm size , safety type aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws ,complete all as specified and directed by Engineer-in- Charge.

Magnetic catcher with Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed,complete all as specified and directed by Engineer-in- Charge.

Magnetic catcher with Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Cupboard knob 40mm dia, fixed with nut, washers / screws etc., of brass polished, bright finished,complete all as specified and directed by Engineer-in- Charge.

Cupboard knob 40mm dia, fixed with nut, washers / screws etc., of brass polished, bright finished and fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of overall length of cover plate 140mm fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

300mm long ordinary rat tail rod pattern MS door springs including roller and roller plate , complete all as specified and directed by Engineer-in-Charge.

300mm long ordinary rat tail rod pattern MS door springs including roller and roller plate fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

Filling of white cement in gaps,joints of tiling,along side wash hand basin,EWC,sink and grating, complete all as specified and directed by Engineer-in-Charge.

Door seal 50mm wide and 1 m in lenth built in aluminium black plate with nylon brush fixed with screws fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

Sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane in and including Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads ,complete all as specified and directed by Engineer-in- Charge. Note:- New wooden required for glazing glass in wooden window will be paid for separately.

Figured glass 3 mm thick, pin headed tyoe and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane in and including Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads ,complete all as specified and directed by Engineer-in- Charge.

Stainless, steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples or fixed to wooden bead , complete all as specified and directed by Engineer-in-Charge.

Stainless, steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples or fixed to wooden bead fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples, etc, complete all as specified and directed by Engineer-in-Charge.

Framed work as in doors/Chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete ( Fe-290,Gde-E-165)in and including dismantling of structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed by the Engineer-in-Charge.

M S work as Framed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc ,drilling bolting or reveting etc and similar work conforming Fe-290 Gde E-165 in and including dismantlingexisting grill ,complete all as specified and directed by Engineer-in- Charge.

Preparation of new or previously untreated wooden surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of red pink primer,complete all as specified and directed by the Engineer in Charge.

Preparation of new or previously untreated steel surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of red oxide primer,complete all as specified and directed by the Engineer in Charge.

Preparation of new or previously untreated steel surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint ,complete all as specified and directed by the Engineer in Charge.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exceeding 10cm girth, and removal of rubbbish outside MOD land,,complete all as specified and directed by Engineer-in- Charge.

Steel water tubing, 15 mm bore medium grade ISI Marked, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Notes: (i) Unservicable steel water tubing retrived from taking down of this item shall be sold to contractor in credit scedule . (ii) Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Steel water tubing, 20 mm bore medium grade ISI Marked , galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Notes: (i) Unservicable steel water tubing retrived from taking down of this item shall be sold to contractor in credit scedule . (ii) Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Rotational moulded PVC, tripple layered, water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. including ball brass valve of 20 mm bore,high pressure,with polythene float and fly nut in and including dismantling PVC water tanks exc 251 ltr but n. exc 500 ltr capacity by disconnecting existing water connection and removal from site ,complete all as specified and directed by Engineer-in- Charge.

Rotational moulded PVC, tripple layered, water storage tanks of capacity 1000 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. including ball brass valve of 20 mm bore,high pressure,with polythene float and flynut in and including dismantling PVC water tanks exc 501 ltr but n. exc 1000 ltr capacity by disconnecting existing water connection and removal from site ,complete all as specified and directed by Engineer-in- Charge.

Ball valve high pressure of PTMT with epoxy coated aluminium door and highdensity plastic ball screwed for 20mm dia iron pipe and fixed (minimum wieght 15mm-142gms/20mm 210gms/25mm 455gms/40mm 690gms ) and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Stop valve /Angle cock, 15 mm bore fancy type chromium plated cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Stop cock regular body with flange, 15 mm bore fancy type chromium plated (concealed type) cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Bib cock long body with flange,15 mm bore fancy type cast copper alloy Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Pillar taps long neck , fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Wall mixer with L bend (provision for over head shower), cast copper alloy, chromium plated for mixing hot and cold water, screwed down for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Brass CP Sink mixer (wall mounted) for mixing hot & cold water fixed in repairs, for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Brass CP central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Shower roses of 125 mm size ,15 mm bore fancy type , chromium plated ,with or without swivel joints, any size, including fixing to steel pipe or GI/Kitec fiitingPillar taps, fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note for Srl Item No 88 to 96:-The quoted rates against these items shall deemed to be included for replacement of damaged GI/Kitec fitting such as socket, elbow,nipple and tee of required size ,fitted/connected and making good any leakage. Nothing extra shall be admissible on this account.

Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 20 mm bore dia fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Wash basins ,vitreous china, white,rectangular type of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia Waste fittings, brass, chromium plated for glazed basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed inluding new brackets fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Vitreous China squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc including 100mm cast iron 'P' or 'S' trap complete including making good to floor fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

PVC valveless , syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC connections 15mm size with PTMT nuts of length 600 mm fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Plastic water closet seat cover good quality in white colour with flat bottom and cover and mild steel chromium plated or aluminium hinging devices, connected to drains outlet, fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Mild steel chromium plated jet including PVC pipe of suitable length for European/ pedestal type WC including all accessories fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Hand shower (Health foucet) cast copper alloy chromium plated with and including 8mm dia 1.00 meter long CP flexible tube and with hook fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC waste pipe flexible for Sink/ WHB of 32mm size fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC cabinet mirror of size 400mmx500mm fixed as in repair,complete all as specified and directed by Engineer-in- Charge. Note : Colour and pattern of cabinet shall be approved by Garrision Engineer.

Sheet glass shelf assembly rectangular type consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed with PVC rawl plugs and wooden screws fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Corner glass shelf of radius 300 mm including 02 Nos. metallic holding brackets, railing etc. fixed with PVC rawl plugs and wooden screws fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Soap dish brass, chromium plated fancy type fixed to plugs with chromium plated brass screws. fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Taking down and Refixing of WHB/SINK to existing position including change of rusted bracket/ fastener as required at site, including refixing of existing piller tap/PVC connection/waste pipe/grating/bib tap etc and making good with white cement/grey cement to match existing surface , complete all as specified and directed by the Engineer in -Charge.

PVC PVC lid with clips, screws, locking device complete, suitable for 500 litre capacity PVC water storage tanks, cylindrical closed top fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

CP grating 125 mm dia/hinged of brass and fixing with cement mortar 1:3 with/without holes as required fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass chromium plated, fixed to walls with screws and plastic cleats fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Fixing only in repairs, pedestal pan and trap, including connection to drain and to flushing pipe, anti syphonage pipe etc.,complete all as specified and directed by Engineer-in- Charge.

Kitchen plate rack made of stainless steel 1 mm thick with plugs washers as overall size of 75cm x 75 cm including fixing to wall and all assessaries fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Kitchen sinks with drainage board made of stainless steel 1 mm thick with plugs washers and waster including beeding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe upto 0.50 sqm each overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160mm fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Finials/Brackets for curtain rod of any size and shape as required at site fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Drapery rod of mild steel 25mm dia, ribbed/fancy type, powder coated, any shade, including set of fixing brackets, for span not exceeding 2m, fixed to wall with PVC finols/finnels, connected accessaries, rubber packing, required screws and PVC rawal plugs as required fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Disconnecting existing tanks of capacity exceeding 250ltrs but n. exceeding 500ltrs, draining out of water, setting a side( or lowering if required) for repair/cleaning and removing accumulated sluge/dirt scales from tank bottom, side and from mouths of circulating pipes of service tanks located on roof of building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enemel paint on black ground "Cleaned on (date)" height of words100mm, and hoisting if required, refixing and reconnecting in position after cleaning ,complete all as specified and directed by Engineer-in- Charge.

Disconnecting existing tanks of capacity exceeding 501ltrs but n. exceeding 1000ltrs, draining out of water, setting a side( or lowering if required) for repair/cleaning and removing accumulated sluge/dirt scales from tank bottom, side and from mouths of circulating pipes of service tanks located on roof of building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enemel paint on black ground "Cleaned on (date)" height of words100mm, and hoisting if required, refixing and reconnecting in position after cleaning ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 75 mm bore single socketed in any length with ruber rings joints or solvent cement laid in trenches or in floor including taking down old pipes and including necessary excavation, return filling and demolition of PCC etc if required ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 75 mm bore single socketed in any length with ruber rings joints fixed to walls with necessary brackets and making good the mouth of rain water pipe including taking down old pipes ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110 mm bore single socketed in any length with ruber rings joints fixed to walls with necessary brackets and making good the mouth of rain water pipe including taking down old pipes ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) bends any radius 75mm bore fixed with solvent cement in any position as per site requirement provided with access door fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) bends any radius 110mm bore fixed with solvent cement in any position as per site requirement fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) floor trap plain 75mm with grating including jointing with solvent cement to waste pipe as per site requirement fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) pipes 75mm bore junction single, (single Tee) equal or unequal with oval access door fixed with solvent cement in any position as per site requirement fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof of 75mm bore of pipe fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof of 110mm bore of pipe fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Cast iron branch pieces 75mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Welding in repair exc 2.5 cm but n exc 5.00 cm in length thickness of metal to be welded n.exc 6mm, including cleaning, preparing the surfaces and holding the member in true position for maintenance of steel items such as gates, grills, doors window etc. ,complete all as specified and directed by Engineer-in- Charge.

Lime concrete moratar 1:2 with 40mm graded brick aggregate to floor in and including demolition of lime concrete/lean concrete/brick bats from sunken portion exc. 15cm thickness (above ground level) in and including removing of debris away from site to a designated point fixed by local administration out side of MOD land , complete all as specified and directed by the Engineer in Charge .

Applying two coats of two component elastomeric acrylic polymer modified cementitious waterproofing coating, smartcare Ultra block 2K or equivalent, having 215% elongation as per ASTMD-2370, resisting 5 bars hyrostatic pressure as per DIN 1048, Crack briding upto 3.50mm as per EN 1062-7 and sprinkling dry fine sand over wet second coating compelete, as per manufactures specifications. , complete all as specified and directed by Engineer-in-Charge. Note: Unless otherwise recommended by manufacturer, the mixing ratio of the components shall be 6 parts of powder and 4 parts liquid without any water addition in the mixing .

Hardcore of gauge n exc. 63 mm of broken brick , deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface , complete all as specified and directed by Engineer - in -Charge.

Plain cement concrete (1:2:4) type B-0 using 12.5 mm graded mechanically crushed stone aggregates using integral water proofing compound @3% by weight of cement as in sunken portion and virtical walls including chamfering on edges, necessary form work in and including demolition of (un-reinforced) cement concrete of any description or as roof padding and coveringg concrete in any position not otherwise specifically provided for and remove all the debris out of MoD land , complete all as specified and directed by Engineer-in-Charge. Note: Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces as in sunken portion in cement mortar 1:4 finished the surfaces even and fair without using extra cement and mixing with water proofing compound as per manufacturers instruction @3% of cement weight , complete all as specified and directed by Engineer-in-Charge. Note: Quoted Rate of above item is inclusive the cost of WPC and nothing extra shall be admissible on this account.

Steel water tubes, 50 mm bore, medium grade, galvanized, as in spout for sunken floor, fixed in wall, inside end fixed with wire netting and external beveled edge at 45 degree, complete all as specified and directed by Engineer - in -Charge.

Mild steel, plain, black of sheet of 1 mm thick iheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required in and including dismantling plain or steel any gauge, thickness, complete all as specified and directed by Engineer-in-Charge.

Note :Schedule of credit to be deducted on acceptances of bid.Details of Schedule of credit is given in tender documentse.

Dhillon Construction Company (BID ID -3087660)

MOHAMMAD RASHID (BID ID -3076133)

Baba Engineers and Contractors (BID ID -3083517)