SPECIAL REPAIR TO BLDG NO P-200 (RECT OTM ACCN) AT 20 CAMP SRC RAMGARH CANTT

Amount

Taking down complete existing roof /parapet treatment any thickness including mud phuska, plastering, leaping plaster of any thickness cuting & up rooting tree roots/Vegitable growth & removing the debris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces clean complete all as specified and as directed.

M & L for PCC (1:2:4) ,type B-0 (using 12.5mm graded crushed stone aggregate) as in padding, benching, sunken portion etc., on roof surface for correcting/making proper slope on roof, etc.,complete all as specified and directed.

M & L for application of water proofing treatment using APP modified roof membrane over non accessible/ non approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface) to be executed through approved applicator of the membrane manufacturer/authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly & apply 10 mm thick plaster /rendering in cement mortar (1:3) with WPC as per manufactures instructions (b) Applying approved bituminous based primer( conforming to IS: 3384-1995) @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface & hot blown grade bituminen 85/25 @ 1.2 Kg/Sqm over primer . (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Applying two coat of bituminious based Aluminium Paint @ 0.3 Kg /sqm over APP Membrane.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the all rubbish off from the premises complete all as specified and directed.

Demolition of plain cement concrete(un-reinforced ) in ground floors, terrazo tiles floor & paving not exceed 15cm thickness (below or above ground level) and removal of rubbish off from site complete all as directed by Engr-in-Charge.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M & L glazed ceramic coloured tiles of size 300 mm x 450 mm x7mm thick ,as in vertical surface such as dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles, over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete reinforced as in chullah hoods, shelves, cover slab and platform, etc,including removal of rubbish out off MOD land etc complete all as specified and directed

M & L for RCC 1:2:4, type B-1(using 20mm graded crushed stone aggregate) as in kitchen platform, shelves ,cover slab, etc. including necessary formwork, complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over grade Fe-500, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for 18 to 20 mm thick granite slab (or any type) table rubbed and pre mirror polished in steps,jambs, pillar,window cill,cooking platforms and like in cement mortar1:4, set & jointed in neat cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over & including 15 mm thick rendering in cement mortar(1:4) etc including dismantling of exsting slab complete all as specifed and as directed.

S& F in repair vitreous China wash basin counter top, star white oval type size 560 mm X 410mm including 32 mm brass chromium plated waste coupling ,PVC 32 mm bore waste pipe, chromium plated grating & making good disturbed surface with CM 1:3 complete all as specified and directed.

S&F in repairs bevelled edge mirror 1200x600x5mm thick of any size mounted on commercial type plywood or AC sheets and fixed to wooden plugs with chromium plated screws including PVC beading complete all as specified and directed.

S&F in repairs bevelled edge mirror 1800 mm x 600 mm x 5mm thick of any size mounted on commercial type plywood or AC sheets and fixed to wooden plugs with chromium plated screws including PVC beading complete all as specified and directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting n.exc 10 cm girth in brick wall complete all as specified and as directed.

Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F in repair vitreous China urinals, bowl type angle back, size of 430 x 370 x 340 mm white (minimum),with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

S&F WC squatting pan " Orissa Pattern" of size 580 mm X 440 mm white with integral foot rest including cast iron "P" or "S" trap, front or back inlet and making connection to trap & to flushing cistern complete including taking down existing pan & making good disturbed surface complete all as specified & directed.

M&L vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device including plastic seat cover & taking down existing pan & making good disturbed surface complete all as specified & directed.

S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S&F repair CP jet spray of standard size for EWC along with CP connection pipe and all fittings complete all as specified and directed.

S & F in repair health faucet(ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connection & fixed in position complete all as specified & directed.

S&F in repair stop cock 15mm bore chromium plated with long shank fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

S&F in repairs 15mm dia bore angle cock cast copper alloy fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for unions complete all as specified and directed

S&F in repair 15mm bore long body (weight not less than 400 gm)bib tap, cast copper alloy, CP fancy type with crutch or butterfly handle, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed

S & F in repair pillar taps long body chromium plated, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed

S & F in repair Grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed by Engineer-in- Charge.

S & F in repair Grating doom 125mm dia with waste hole of PTMT (minimum weight 40gms) complete all as specified and directed by Engineer-in- Charge.

S & F in repair brass chromium plated shower rose with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specifed & as directed.

S&F in repair for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair chromium plated (CP) soap tray of size 160x160x90mm, complete all as specified and directed.

S&F in repair towel rail brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed.

S & F in repair 32 mm dia bore waste pipe fixed to wash hand basin complete all as specified and directed by Engineer-In- Charge.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole complete all as specified and directed.

S & F in repair 110 mm dia PVC(SWR) WC connector with lip ring, complete all as directed and as specified.

S & F in repair 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S & F in repair PVC (SWR) bends for 110mm dia PVC pipes with rubber ring joints complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) branch piece, double(double Y) equal or unequal complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) vent cowl complete all as specified and directed.

S & F in repair 75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F in repair PVC (SWR) bends 75mm bore of any radius all as specified and directed

S&F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) vent cowl complete all as specified and directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frames) of any description not exceeding 1.5 Sqm each, complete all as specified and directed.

Forming jambs, etc, in CM 1:4 to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engineer-in-Charge.

S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube for top and bottom rails. mild steel framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S & F 100mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed .

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 150 mm aluminium alloy handles of extruted section type, anodised complete all as specified & directed.

S&F 300mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off from site etc complete all as specified and directed.

M&L for Brick work with using old size sub class "B' bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

S&F rotational moulded polythene water storage tank of capacity 2000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 25 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) including taking down of existing tank complete all as specified and directed.

S & F in repair 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

Taking up or down steel tubing and connections of 25mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 25 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

Demolition of plain cement concrete(un-reinforced ) in ground floors, terrazo tiles floor & paving exceeding 15cm thickness (below or above ground level) and removal of rubbish off from site complete all as directed by Engr-in-Charge.

M & L for plain cement concrete (1:5:10), type E-2 (using 40 mm graded brick aggregate) as in sunken portion, sub-base, etc., complete all as specified and as directed.

M&L for 10mm thick cement plastering in CM 1:3 finishing even and smooth without using extra cement mixed with WPC as per manufacture instructions complete all as specified and as directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

M&L for laying 30 mm thick PCC 1:2:4 type B-0( using 12.5mm graded crushed stone aggregate) mix with WPC as per manufacturer instructions on bottom up sunken portion with proper slope towards spout complete all as specified and as directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

S&F 150 micron thick polythene film pasted with the help of adhesives shall be provided over treatment, complete all as specified and as directed.

S&F 50mm dia light grade laid in floor as spout pipe projecting 450mm clear outer face of wall to be fixed for drain out water, complete all as specified and as directed.

Supply only liquid water proofing compound (ISI mark)complete all as specified and directed.

M & L for application of water proofing treatment of sunken portion of WCs ,bath room etc., to be executed through approved applicator of the membrane manufacturer/authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying two coat of Shalimar supercreten/Nitobond/Dr Fixit of make as approved in technical instructions. (c) Fosroc's complast X421 IC@ 130ml per bag of cement including a bonding coat of Fosroc's Nitto bond AR cement slurry /STP No. 1 liquid @200 ml per bag complete (d) This treatment shall be allowed to air curefor four hours followed with water tightness by ponding for 72 hours and rectify defect,if any till elimination of defects.

Taking down cement plaster on brick wall or concrete surface etc including raking out joints hacking for key scrubbing down with water etc & removing the debris from the premises upto 500 m from the MOD land complete all as specified and directed.

M&L for 15mm thick rendering (external) on brick or concrete surface in cement mortar 1:4, finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering (internal) on brick or concrete surface in cement mortar 1:6, finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick cement plastering in cement mortar 1:4 on concrete ceiling surfaces finished even & smooth without using extra cement omplete all as specifed and as directed.

M&L for precast reinforced cement concrete 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregate) as in kitchen platform, shelves ,man hole cover slab, etc. including necessary formwork complete all as specified and directed. Note : Reinforcement will be measured & paid seperately under respective item of BOQ.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in reinforcement ,cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M& L for Brick work with sub class 'B' bricks straight or curved on plan to any radiusin half brick thick wall built in cement mortar 1:4, complete all as specified and directed

Dismantling stone slabs of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, and removal of debries from site complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18mm -20 mm thick( size not less than 575 mm X 575 mm), laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing with beeswax polishing into mirror finish over & including 20 mm thick screed bed in CM (1:4) complete all as specifed & directed.

M& L for machine cut Kota stone slab 16 to 18mm thick as in vertical surfaces such as skirting/dados in narrow width, laid and jointed with grey cement slurry pointed with cloured cement to match the shade of the slab including grinding rubbing with beeswax polishing into mirror finishover 10 mm thick backing coat in CM (1:4) etc complete all as specifed & directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed.

M&L for preparation of newely plastered surfaces of wall and applying three coats of white wash on wall surface complete all as specified & directed.

M&L for preparation of newely plastered surfaces of ceiling and applying three coats of white wash on ceiling complete all as specified & directed.

M&L for preparation of newely plastered surfaces of wall and applying two coats of colour wash complete all as specified & directed.

M&L for prepatation of new plaster surface and applying two coats of distemper oil emulsion (OBD) over a coat of alkali resistant primer (from same manufacturer of OBD) and a layer of wall care putty not less than 2mm thick complete all as specified and directed.

M & L for preparation of old decorated surfaces of walls including brooming down or steel wire brushing, scrapping down smokes soot moulds, moss and efflorescent salts and treating oil and greasy spot & applying one coat of white wash on wall complete all as specified & directed.

M & L for preparation of old decorated surfaces of ceiling including brooming down or steel wire brushing, scrapping down smokes soot moulds, moss and efflorescent salts and treating oil and greasy spot & applying one coat of white wash on ceiling surface complete all as specified & directed.

S & F punching small holes for nails or screws, hand punch through iron or mild steel in plain aluminium sheet for crumple joints complete all as specified and directed.

S&F 1.0 mm thick mild steel, plain, galvanised in straight flashing fixed in crumple joints with grade of Zinc coating 275 complete all as specified & directed.

M&L for repair and rendering 10mm thick in cement mortar 1:3 on chajjas not exceeding 60cm width after removing cracked plaster and concrete surface including cleaning of visible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete 1:2:4 type B-O( using 12.5mm graded crushed stone aggregate )including necesssary scaffolding work for double/single storey building complete all as specified and directed.

Hacking out old broken glass(any thickness, size, quality or description) from wooden frames/steel frames, glazed with oil putty or fixed with beads complete all as specified and directed

M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engr-in-Charge .

M&L for securing glass of any description in existing metal frames glazed with putty & glaze pin including removing loose or decayed putty, reputtying and painting surface to match existing work, complete all as specified and as directed by Engr-in-Charge .

S & F in repair for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F for steel ventilator with top hung shutter including hinges, steel peg stay, complete including prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

S&F 3.0 mm thick figured glass pin headed type in squares/ rectangular not exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete etc all as specified & directed.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.0 Sq m each, and removing from site, complete all as specified and directed by Engineer-in-Charge .

S& F 32 mm thick, flush shutters factory made, kiln seasoned and ASCU treated solid core construction, with block board core and ply wood face panels, commercial type on both sides decorative face with lipping/ frame complete all as specified and directed.

S & F 35 mm thick, factory made, IInd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (divided into squares with plain, chamfered or rounded, mitred and rebated sash bars any number size of members), beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); kiln seasoned & chemically pressure treated etc complete all as specified and directed . (Note:- (i)Glass / wire cloth shall be measured & paid separately.(ii) Sample of shutter in sample room of GE office.)

S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

S & F for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F for first class hard wooden beads of size 10x10 mm to 15X15mm of teak wood Square / triangular in cross section, plain or desiger for fixing of mosquito net jali /glazed or gauged joinery,renewed complete all as directed by Engineer in Charge.

M&L for prepartion of new or previously untreated wooden surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

Taking down carefully unserveciable/damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets ,light fittings etc) and removing material from site and making good to the disturbed surface to match with existing finish etc complete all as specified and directed.

M & L for point wiring for one light/fan/exhaust fan point/ bell /buzzer point controlled by one way switch with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box (normal & modular type) made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminated cover make sheet for housing/ fixing switches etc., including cutting holes for switches,sockets,regulators etc as per requirement including fixing with machine screw,washer etc for the following

(a) One light point controlled by one way switch

(b) One fan point controlled by one way switch on ceiling using existing conduit.

(c) One 3/5 pin socket outlet 5 Amp on the same board with other switches

(d) One 3/5 pin 5 Amps socket outlet on independent board

M & L for point wiring for 15 Amp 3/5 pin socket power point with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 2.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 2.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box (normal & modular type) made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminated cover make sheet for housing/ fixing switches etc., including cutting holes for switches,sockets,regulators etc as per requirement including fixing with machine screw,washer etc for the following

& F scoket outlet polycarbonate 2 in 1, 3 pin, 15 Amp flush type, universal, complete all as specified & as directed .

S & F switch piano 15 Amp, flush type, one way single pole complete all as specified and as directed.

M & L Sub main wiring with two runs of single core 6.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall including taking down existing sub main wiring complete all as specified and as directed. Note : - Two runs of 6.0 Sqmm cable and one run of earth wire 6.0 sqmm & conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder.

S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed.

S & F socket outlet 2 in 1, 3 pin, 5Amp, flush type, universal, complete all as specified and as directed.

S & F ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified & as directed

S&F fan regulator electronic, step type hum free, socket type, suitable for ceiling fans of any capacity, pre wired 230 volts AC 50 HZ supply 100/120 Watt complete all as specified & as directed

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified & as directed

S & F LED bulb of capacity 10 watt , lumen out put (1200)lm ,length 102 mm dia 56 mm , base cap B22, (ISI marked), complete all as specified & as directed

S & F Inverter LED bulb of capacity 12 watts lumen output (1200) length 140 mm width 70mm base cap B22 ,(ISI Marked) three star complete all as specified and directed.

S & F LED tube light fitting 1 x 20watt , 220 V, AC, decorative box type with driver ,holder including LED tube light surface and wall mounted LED batten PVC housing with polycarbonate diffuserand integrated electronic driver complete with all accessories ,driver, holder including LED tube light connecting up with two core flexible copper conductor cable and flexible pipe of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engineer-in-Charge.

S & F in repair LED mirror type light fittings 1 x 9/10 watts integral slim LED batten with high out put diffuser 2 feet long ,220 volt ,AC decorative type with driver holder & LED lamp & all other accessories duly pre wired and making connection with and including two core flexible copper conductor cable and flexible pipe of suitable size from connector to ceiling rose not less than 1 mtr fixed on wall with plastic gutties complete all as specified & directed.

S&F 1X9 W/1X10 W watt LED Bulkhead fitting with IP 65 environmental frendly, ultra modern, energy saving mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 230 Volts AC circuit complete all as specified and as directed.

Taking down ceiling fan of any sweep after disconnecting all necessaryelectrical connctionsfromceiling rose to fan and refixing of the smeat existtttttng location and including connecting up three core single flexible wire with flexible pipe after completion of all work complete all as specified and directed.

upadhyay engineers and consultant

M/S KAMLESHWAR SINGH

M/S SHAMBHU SHARAN SINGH

simplex infra project

Balaji Construction And Company

M/S PARAS NATH SINGH