PROVN OF CERTAIN B/R AND E/M WORKS SERVICES IN TEACH AREA AT AF ATN JAMNAGAR

Amount

NOTE: Schedule ‘A’ Part I to IV are under Ser No. 1.00 to 4.00. are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Lump sum price worked out for Building / Structures as listed in Sch `A’ Part I.

Lump sum price worked out for (SITE CLEARANCE, EXCAVATION AND EARTHWORK) as listed in Sch `A’ Part II

Lump sum price worked out for INTERNAL ELECTRIFICATION as listed in Sch `A’ Part III

Lump sum price worked out for EXTERNAL ELECTRIFICATION as listed in Sch `A’ Part IV.

SCHEDULE 'A' PART - V (MISC ITEMS) (Note for items here in after: The contractor shall quote his rate for each of these items separately. The estimated rate is left blank since the same is not prepriced by MES)

Demolition of stone slab and tiles of any description or thickness in floors, apron, dado, striting etc laid, bedded and pointed in any mortar.and rubbish off the premises, complete all as specified and as directed.

Demolition Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed.

Demolition cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Taking down chowkats or frames n.exc 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 but n.exc 4 Sqm each with shutters(without taking off shutters from the frames) complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry with solid blocks type C-1, 1:3:6 (using 20mm graded aggregate) , exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed.

M&L for rendering 10mm thick on brick/concrete surface in CM 1:6 to wall finished even and smooth without using extra cement all as specified and directed.

M&L for rendering 15mm thick on brick/concrete surface in CM 1:4 to wall finished even and smooth without using extra cement complete all as specified and as directed.

M&L preparation of newly plasterd surface on wall and applying two coats of oil bound distemper over a coat of primer after complete all as specified and as directed.

M&L for preparation of newly plasterd surface on ceiling and applying two coats of oil bound distemper over a coat of primer after complete all as specified and as directed.

M&L for preparing to cement plastered surfaces and applying two coats of cement base paint over a coat of compitible primer complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 type B-1 (Using 20mm graded stone agg) , 25mm thick as in sub base in floor/paving etc, complete all as specified and as directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding of cm 1:6 layer in floor finishes complete all as specified and as directed.

M&L coloured ceramic glazed tiles 300x200x7mm thick on vertical surfaces such as skirting, dados and rises to steps etc set in jointed in neat cement sluury 10 mm thick plaster in CM 1:4 and pointed to match the colour of tiles complete all as specified and complete.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding of cm 1:6 layer in floor finishes complete all as specified and as directed.

S &F for framed work such as grills, grating etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars (for windows); barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work cnforming to Fe 290. Gde E-165, complete all as specified and as directed.

S & F in position aluminium powder coated (min thickness of powder coating 50 micron of approved colour) three track window (two shuttes glazed and one shutter wireguage) with frame, glazed with 4mm thick tinted glass and wire guage with stainless steel wirecloth 0.36mm nominal dia of wire and average width of aperture 1.40mm incl rubber bead joining cleat for fixing in position, concealed type lock for all three shutters, PVC roller etc all as specified and as directed by Engr-in-Charge. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm (section No 20831) (b) Frame (Bottom) section shall of size 92.00 x 31.75 x 1.50 mm (Section No 20832) (c) Top and side members of shutter section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20738) (d) Shutter Interlock section shall be of size 18.00 x 40.00 x 1.45 mm (Section No 20737) (e) Bottom members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736) Note :- Section no given above are of make Jindal, Contractor may use similar section of other make mentioned in Contract Aggrement.

S & F 2nd class hardwood, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed in position complete all as specified and as directed.

S&F mild steel bands, straps, supports or stays for rainwater pipes, soil/ waste or vent pipes including bolts, if required, in hold fast; wall ties; hooks for hanging fans and similar small article confg to Fe- 290-Gde - E-165 complete all as specicifed and as directed.

S&F 35 mm thick 2nd class hardwood, Plain, framed, panelled Factory made shutters (two panels), with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I) klin seasoned and chemically pressure treated, complete all as specified and as directed.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutter of factory made divided into square, with plain chamfered or rounded mitred and rebated sash bar any number with edges of sash bar & framing moulded all as specified as per IS fitted to chowkats complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and as directed.

S&F butt 100mm size, hinges medium weight, cold rolled mild steel, etc complete all as specified and directed.

S&F 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, complete all as specified and as directed.

S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed.

S&F 300mm, ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

S& F aluminium anodised tower bolt of extruded section, 150mm long, etc complete all as specified and directed.

S&F aluminium handle extruded aluminium alloy fabricated type, 150mm size etc complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tounge, anodised with hard drawn spring fixed in floor, overall length of cover plate 150 mm complete all as specified and as directed.

S&F in repair vitreous China squatting pan 'Orissa' pattern of size 580mmx440mm white with integral foot rest (excluding flushing cistern) but including PVC (SWR) 'P' trap set in and including lime concrete complete all as specified and as directed.

S&F Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x330mm x 160mm complete all as specified and as directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet ball valve, float and handle including flush pipe and brackets complete all as specified and as directed.

M&L for 1.6mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. and welded to frame if required complete all as specified and as directed.

M&L for Joist, channel, angle, or tee sections, Fe-290 (Gde-E-165), fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

M&L for hardcore of broken stone or boulder gauge n exc. 63 mm, deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick Cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in floor finished even and smooth without using extra cement complete all as specified.

M&L for Glass dividing strips, 3 mm thick, 28mm Width of strip and inserted in position, conform to design complete all as specified and as directed.

M&L rubber moulded coloured glossy finished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, Made with M-35 Grade concrete with grey cement and pigments laid on compacted sand cushion of 25mm thick complete all as specified and as directed.

S&F tubular towel rail 20mm dia, D type 60cm long between flanges, Aluminium annodised complete all as specified and directed.

S&F vitreous china wash hand basin pedestal pattern, flat back size 550x400mm including pedestal, bracket, waste coupling etc complete.

Supply, lay, connect and test GI tubing ,medium grade with all fitting, laid in trenches, or fixed to walls with clamps, floors, ceiling etc, complete of 15mm bore complete all as specified and as directed

Supply, lay, connect and test GI tubing ,medium grade with all fitting, laid in trenches, or fixed to walls with clamps, floors, ceiling etc. complete of 20mm bore complete all as specified and as directed

S&F bib taps, cast copper alloy fancy type chromium plated, 15mm dia of bore etc complete all as specified and directed.

S&F stop cock, cast copper alloy, fancy type chromium plated, 15 mm dia bore etc complete all as specified and directed.

S & F for Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, Bore dia of pipe in 15 mm, etc complete all as specifed and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specifed and directed.

S&F PVC connection 15mm size, 450mm long with PTMP nuts both side,etc complete all as specified and directed.complete all as specifed and directed.

S&F pillar cock fancy type cast copper alloy, chromium plated 15mm dia of bore etc complete all as specified and directed.

M&L 32 mm dia Waste pipe fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end complete bedded in red lead cement and other end fixedwaste pipe fixen with waste coupling complete all as specified and directed.

M&L preparation of new steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specifed and directed.

S&F PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement, complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvent laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvent laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for 110mm bore PVC (SWR) bends any radius complete all as specified and directed

M&L for cement concrete 1:4:8 type D2 (using 40mm graded aggregate) in foundations, filling and mass concrete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded aggregate) as in embedding of angle iron post and filling complete all as specified and as directed.

M&L for rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 (Gde-E-165) complete all as specified.

S&F High tensile galvalume sheets colour coated single skin high rib / multi rib TMP Profile Galvalume sheeting in roof having 1000-1020 mm width 28 mm high crest @ maximum 250 mm pitch (centre to centre) and minimum 190mm manufactured out of 0.50 mm TCT (total coated thickness) cold rolled steel, having yield strength 550MPa minimum and wall coated with 25 micron modified polyester paint system applied on Zincalume on top and with back coating on sheet shall be 7-10 micron epoxy paint. The sheet shall be supplied in length maximum upto 6-12 meters long to suit with structural dimensions and fixed with self tapping screws with built in gasket (with bitumen washer) of suitable size machine fixed as per manufacturer instructions and applying adhesive compound to joint overlap of sheets complete all as specified and as directed.

S&F 1.00mm thick and 150mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges complete all as specified and as directed .

S&F MS Angle Iron as in fencing posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire,etc and flat iron fillets (for securing wire mesh etc.) conforming to Fe-290 Gde E-165 complete all as specicifed and directed.

Fixing only chain link fencing of any mesh size/any type incl. link wire to any type of standard rails/ supports etc & straining bolt etc incl. provision of binding wire complete all as specified.

Supply for Chain link MS galvanisd fencing, any size or type, etc complete all as specified and directed.

M&L mild steel round bar 10 mm and over as in tightening of chain link fencing including cutting to shape, necessary drilling, bolting etc Fe-410-W (Gde E-250) quality -A or Fe 290 (Gde-E-165) complete all as specicifed and directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 but n exc 10 cm long,Diameter of neck in 16 to 20 mm, etc complete all as specified and directed.

M&L for preparation of new steel surface of any description over 10cm width or girth when uncon nected with other painting or when painted in a different tint and applying two coat of synthetic enamel paint over a coat of red oxide primer, etc complete all as specified and directed.

M&L for mild steel corrosion resistence steel (CRS) TMT reinforcement bars of grade Fe-500 D / 550D, 10 mm dia and over cut to length and bent to shape required including cranking, bending spirally for hoping for columns, hooking end and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to GD-I. IS-432 (Part I) complete all as specified and as directed.

M&L mild steel corrosion resistence steel (CRS) TMT reinforcement bars of grade Fe-500 D / 550D, 8mm dia and over as in stirrups spacer and binder, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for reinforced cement concrete M-30 (design mix) using 20mm graded crushed stone aggregate in Foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use and waste of Formwork to sides of concrete foundations and plinth beams rough finished concrete surfaces complete all as specified and directed.

M&L for reinforced cement concrete M-30 (design mix) using 20mm graded crushed stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.

Use and waste of Formwork to sides of Columns, rough finished concrete surfaces complete all as specified and directed.

M&L 20 mm thick granite stone slab of any type with table rubbed and polished for wall lining set in cement mortar 1:3 and jointing with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab over 5mm thick plaster in CM 1:3, complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering confirming to Fe 290 (Gde E 165) . Door, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete all as specified and as directed.

Supply and fixing of flame proof Exhaust fan 300mm in aluminium alloy LM 6 construction, certified by CMRS, Dhanbad for Group I, IIA, IIB complete all as specified and as directed.

Supply and fix Flame proof air circulator 600 mm in aluminum alloy LM 6 Construction , certified by CMRS, Dhanbad for Group I, IIA, IIB, complete all as specified and directed. .

Supply and fix of flame proof and weather proof industrial type DBs with and including various combination of incoming and outgoing flame proof MCBs suitable for and including (a) 01 No MCB TPN 63 Amps, C type (incoming) (b) 06 Nos MCB SP 10 Amps C type (c) 2 Nos MCB SP 20 Amps C type, including necessary connection, complete, all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and capacity 10 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and as directed.

Supply and fixing of Crash/gong bell 9 inches to be fixed on wall connected all as specified and directed

Supply, installation testing and commissioning of EOT Crane indoor type of capacity 2.5 ton medium duty class-II electrically operated OH complete without railing track having following configuration including providing required load for testing and furnishing certificate and testing report as directed by engineer in charge. Span : 12 to 16 meters, Bay length : 28 meters, Hook lift : 4.5 to 6 meters, Speed Hoist : 3.6 MPM & 0.72 MPM, LT : 22.0 MPM & 4.4 MPM, CT : 15. MPM & 3.0 MPM LT & CT Rail : 40 mm sqBar Note: (i) Required load for testing of crane will be provided by the contracor under his own arrangement. (ii) Load testing shall be carried out through authorised service provided of OEM as per specifided and directed by Engineer-in-charge and Contractor shall produce certificate after load testing for the same. (iii) Contractor shall be submitted three copy of load testing certificate duly signed by Engr-in-charge shall be kept in record. Note : i)Crane to be installed on existing track and parallal to exting manual type crane . (ii (ii) The cable and connection from crane to existing Panel board is deemed to include in this item.

Supply & installation testing of Air Cooled Inverter based Flame proof split AC( Indoor unit Flameproof & outdoor unit Non flameproof) unit with cooling functions and suitable to operate at ambient conditions of (-10 to 46 Deg C in cooling Mode). Air conditioner will have following conditions:- (i) Refrigerant - R 410a (non CFC) (ii) EER - min 3.5 w/w (5 star rating) (iii) Tonnage - 1.5 (iv) Indoor Noise Level - Not more than 48 Db (v) Filter - (a) Must have PM 2.5 µ Filter (b) Electrostatic dust filter (c) Oxidizer dust filter (vi) Functions of remote : (a) Air directional control (b) Auto Timer (c) Economic sleep mode (d) Auto fan speed (e) Auto swing (f) Temp display (g) Turbo mode All specification will be as per IS-1391 (Part 2) 1992 Room Air Conditioners

Note:- Following will be inclusive in the above rate:- (a) Piping insulation and cable length upto 15 mtr . (b) Installation will include fixing the outdoor unit on the platform as per direction of Engineer in Charge. (c) Installation will also include civil work for making hole on the wall and putting the iron sleeve for passing the refrigerant pipe. (d) Testing and commissioning of the Air conditioner to the entire satisfaction of Engineer in Charge. (e) Contractor will provide min warranty of 5 years for compressor from the date of installation. (f) Air conditioner will be tested by the Garrison Engineer for Energy Efficiency and all the functions provision in the Air conditioner. (g) Contractor provide complete free service in warrenty period by the company.

S & F flame proof metal clad plug & socket board Single pole and neutral enclosure with two pin and earth metal plug & socket complete with 20 Amp MCB SP, C curve complete all as specified and as directed.

M & L for providing dry river sand as in sand cushioning below and above cable thickness as specified in SSR to underground cable including punning down of sand in layer all as specified and directed by Engg-in-Charge. Note: For measurement purpose any punned thickness of sand will be considered.

KEVAL ENTERPRISE

JAMNAGAR ELECTRIC AND MACHINERY CO

Nitesh Enterprise