SPECIAL REPAIRS TO BLDG NO E-2 (DEAL HOUSE) AT RESIDENTIAL AREA OF DEAL AND CERTAIN SANCTIONED MINOR WORKS UNDER GE (I) RND DEHRADUN

Amount

Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone works and precast concrete articles, complete all as specified and directed

M&L Brick work with sub class B bricks cold size straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as Specified and directed

Taking down existing cement or cement lime plaster/Grit wash of any description and in any position on brick or concrete surfaces etc including racking out joints, hacking for key scrubbing down with water etc complete all as specifed and directed.

M&L for Rendering 15 mm thick of external surfaces of concrete/brick in two layers first layer 10 mm thick in cement mortar 1:6 and top layer or 5mm thick in cement morter 1:4 mixed with water proofing compound as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid seprately as supply only under respective item of Sch 'A'/BOQ

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 3 mm of water proof wall care putty in two coats including preparation of external new plastred surfaces of wall complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed. (ISI Marked)

M&L for 15 mm thick rendering in CM 1:6 internal surface of brick/ concrete finished even and smooth without using extra cement complete all as specified and directed

Demolition of cement concrete Reinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) reinforcement cut as required to facilitate demolition complete all as specified and directed.

M & L for use and waste providing RCC 1:2:4 type B1 20 mm graded stone aggragete Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed.

M& L for form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed.

M& L for Mild steel TMT bars 10 mm dia and over , cut to length, bent to shape required, including cranking, bending spi-rally for hooping for col-umns, hooking ends and binding with and in-cluding mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L rendering 5 mm thick of brick / concrete surface in cement mortar 1:3 on ceilling surface finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for preparing of new plastered surface on wall and applying two coats of Oil bond distemper over a coat of alkali resitance primer over 3 mm thick wall care putty in two layer on plastered surface complete all as specified and directed.

M&L for preparing of new plastered surface on ceiling and applying two coats of Oil bond distemper over a coat of alkali resitance primer over 3 mm thick wall care putty in two layer on plastered surface complete all as specified and directed.

M&L for complete removing of existing treatment and preparing of old existing plastered surface of celling and applying two coats of Oil bond distemper over a coat of alkali resitance primer over 3 mm thick wall care putty in two layer on plastered surface complete all as specified and directed.

M&L prepration / cleaning of old wooden surfaces over 10 cm width or girth and applying one or more coats of french polishing including a coat of wood filler complete all as specified and directed.

M&L for prepration of old wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for prepration of old steel surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for complete removing of existing treatment and preparing of old existing plastered surface of wall and applying two coats of Oil bond distemper over a coat of alkali resitance primer over 3 mm thick wall care putty in two layer on plastered surface complete all as specified and directed.

Dismantling floor, hearth or wall tiling/stone including cement mortar bedding (but not backing) or of any description , removing serviceable tiles to store and rubbish off the premises as directed complete all as specified and directed.

M & L for double charged , Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and over and including bedding layer of screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

All as per No 21 above, but in skirting over and including 10 mm thick back coat in 1:4 CM complete all as specified and directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (square/rectangular) area of each tilles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. Set & jointed in neat cement slurry and pointed in colored cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

All as per item No 23 above but on vertical surface such as dado, skirting etc over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L coloured glazed ceremic tiles in vertical surface 350x250x7 mm /450x350x7 mm thick set & jointed in neat cement slurry and pointed in colored cement to match coloured tiles laid over and including 10 mm thick rendering in cm (1:4) complete all as specified and directed

Dismentling of stone slabs and tiles of any description or thickness in floors, approns etc,laid bedded and pointed in any mortar complete all as specified and directed.

M & L for 16 to 18mm thick Granite stone slab (of any type/Colour ) Slabs machine cut in skirting/dado and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over and including 15mm thick cement mortar 1:4 , on fair faces of brick work or concrete surfaces as backing for Granite stone slab complete all as specified and directed.

S&F Stainless steel framed work of Grade- 304 of 01 mm thich such as grills, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works fixed through fastenars conforming to IS complete all as specified and directed.

Taking down Chowkats or frame with shutter ( without taking off shutters from the frame) not exc. 1.5 sqm each complete all as specified and directed.

Taking down Chowkats or frame with shutter ( without taking off shutters from the frame) exc. 1.5 sqm but exc 4.0 sqm each complete all as specified and directed.

S&F powder coated aluminium frame for doors, windows or partition including aluminium beading, hinges of required size,jointing cleats, screws, dash,fastners,plug for fixing with wall, columns complete all as specified and directed. .

S&F powder coated of any colour aluminium door shutters, aluminium section like lock rail, bottom rail 115x38/40 mm and top rail and vertical rail 100x38/40 mm including necessary jointing cleats/glazing clips, rubber neorene packing handles 02 Nos in each door, locking arrangment, aluminium snap beading screw etc, complete all as specified and directed. (panels likes prelaminated particle board / sheet glass shall be measured and paid seprately)

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Area notexc 2.Sqm and all fittings and fixture complete all as specified and directed. Note:- The glass pane shall be measured and paid separately.

S&F sheet glass 4.8 mm thick, ordinary quality and glazing with oil putty in square area exceeding 0.5Sqm in each pane complete all as specified and directed

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chreme on newly steel & iron surfaces of any description, not otherwise, described, over 10 CM width or girth including preparation of new surface complete all as specifed and directed.

S&F 40 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specifed and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specifed and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, in opening as per specification & drawing complete all as specifed and directed.

S&F 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chwkats etc complete all as specified and directed.

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specifed and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed and directed.

S&F Floor door stopper double leg of 140 mm overall length aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specifed and directed.

S&F 100 mm long mild steel butt hinges, medium weight cold rolled including welding if required complete all as specifed and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified

S&F 125 mm size aluminium handles,cast type anodized D type complete all as specifed and directed

S&F 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate including welding if required complete all as speified and directed

S&F in 18 to 19 mm thick solid factory made PVC board for cup board/cabinate shutters with one or both side laminated printed PVC celluka board ,anti termite and anti moisture proof etc sheet fixed with & including suitable PVC frame and Magnetic door catcher as per specification & drawing complete all as specified and directed.

S&F 35 mm dia brass knobs for cupboard fixed with nut and screw and washer of mild steel, bright finished complete all as specified and directed.

S&F continous (piono) hinges mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S&F 125 mm long hasp & staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed

Taking down rain water pipes (any size or pattern) including all fittings, heads , Shoes, Bends, Swan neck etc complete all as specified and directed.

S&F 110 mm dia PVC (SWR) Rain water, pipes fixed to walls complete all as specified and directed.

S&F 75 mm dia PVC (SWR) Rain water, pipes fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends/shoes, 110 mm bore dia fitted with access door complete all as specifed and directed.

S&F PVC (SWR) bends/shoes, 75 mm bore dia fitted with access door complete all as specifed and directed.

S&F PVC (SWR) Tee reducer 110 or 75mm complete all as specifed and directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia fitted with access door complete all as specifed and directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia fitted with access door complete all as specifed and directed.

S&F PVC (SWR) Grating doom of size 150 mm complete all as specifed and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re fixing complete all as specifed and directed

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re fixing complete all as specifed and directed

M&L Cutting chases, pinning in, making good to facings where required and pointing in CM(1:3) to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick wall complete all as specifed and directed.

S&F, laying and testing for 15 mm bore GI tubing medium grade galvanised steel tubing including all fittings such as union, reducer, sockets, reducing bends elbows tee, checknuts, caps, plugs etc fixed to wall and ceilling or laid in floors complete all as specifed and directed.

S&F, laying and testing 20 mm bore GI tubing medium grade galvanised steel including all fittings such as union, reducer, sockets, reducing bends elbows tee, checknuts, caps, plugs etc fixed to wall and ceilling or laid in floors complete all as specifed and directed

S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified and directed

S&F as in repairs vitreous chiana wash (Laguna) floor mounted two piece clsoet 'S' trap Surare 475x340x750mm soft close seat cover twin flushing cistern complete all as specified directed . Make:- Modul No 4129 Aquifer EWC P Trap of prayag & equivalent make of CERA, Hindware.

S&F in repairs vitreous china,white table top wash hand basin 410mmX315mmX105mm including bottle trap and other fitting / features complete all as specified and directed Make:- Modul No 4701 (PRISTINE) of prayag & equivalent make of CERA, Hindware.

Chromium plated brass hot & cold basin mixer with centre hole for WHB and long shank fancy type 15mm bore fixed in repair complete all as specified and directed Make: ESSCO (Jaquar) cat No SQT-516KN or equivalent of Make cera/Hindware

Chromium plated Wall Mixer 3-in-1 fancy type with provison for both hand shower Overhead Shower complete with Aerator, connecting legs & wall flange etc 15mm bore fixed in repair complete all as specifed and directed Make ESSCO (Jaquar) cat No,SQT-519KN or equivalent of Make cera/Hindware

Chromium plated Wall Mixer with Bend Pipe for connection to Overhead Shower (with Bush & Piston Diverter Fitting) with Aerator, connecting legs & wall flange etc 15mm bore fixed in repair complete all as specifed and directed Make ESSCO (Jaquar) cat No,SQT-517BKN or equivalent of Make cera/Hindware

S&F in repair 20mm dia brass chromium plated tubular towel rails,D type,60cm long between flanges,complete all as specified. Make ESSCO (Jaquar) cat No,AEC-1111N or equivalent of Make cera/Hindware

S&F in repair soap dish vitreous China white approximate size 160x 160x90mm type fixed with screw to wall complete all as specifed Make ESSCO (Jaquar) cat No,AEC1131N or equivalent of Make cera/Hindware

S&F in repair Chromium plated health fauset with 1.20 meter long flexible PVC tube fancy type with necessary brass nuts & rubber washers cover with chromium plated spring complete all as specified and directed. Make ESSCO (Jaquar) cat No,ALEESS583 or equivalent of Make cera/Hindware

15mm bore stainless steel jet spray with 1.00meter PVC tube fixed in repair complete all as specified and directed. Make: ESSCO (Jaquar) Cat No. ALE-547 or equivalent of make Cera/Hindware

S&F in repair 20 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repair 25 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repair 15mm size PVC connections internally threaded with PVC washer,PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair Grating 100 mm dia of CP with or without hole complete all as specified and directed.

15mm bore long body bib tap with wall flange fixed in repair complete all as specifed and directed. Make: ESSCO (Jaquar) cat No. SQT-512KN or equivalent of Make cera/Hindware

S&F in repair 125 mm size Brass Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specifed and directed. Make: ESSCO (Jaquar) cat No. SQT-542A or equivalent of Make cera/Hindware

Chromium plated Stop valve 15mm dia cast fixed in repair complete all as specifed and directed. Make: ESSCO (Jaquar) cat No.SQT-513BKN or equivalent of Make cera/Hindware

15mm dia chromium plated concealed stop cock, heavy body screwed both ends for iron or for union fixed in repair complete all as specifed and directed. Make: ESSCO (Jaquar) cat No.SQT-514AKN or equivalent of Make cera/Hindware

15mm dia pillar cock Super Delux with Aerator fixed in repair complete all as specifed and directed. Make- ESSCO (Jaquar) SQT-508KN or equivalent make of cera/Hindware

S&F as in repair tolilet paper holder, chromium plated, box type to walls with CP (CP) brass screws complete all as specifed and directed.

Glass shelf 600 mm long complete all as specified and directed. Make: Jaquar Cat Part No ACN 1171N or equivalent to Marc/Zoloto

S&F as in repair brass CP bottle traps for WHB with inlet and outlet screwed for pipe or connections including necessary packing union and cap fixed for 32 mm bore complete all as specified and directed Make- ESSCO (Jaquar) SQT-ALE773ML 190X125 or equivalent make of cera/Hindware

Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter on to dwarf wall or inclulding fixing cantilver brackets and connecting union to pipe overall size 914 mm x 460x 203 mm bowl size 405 mm x 354 mm x 203mm complete all as specified and directed. Make :- Make:- Prayag Cat part No.1239DM or equivalent in Blue star/Nirali.

Stainless steel plate rack of size 31 inch X 36 inch X 10 inch fixed in repair complete all as directed. Make :- Make:- Prayag Cat part No.P-348 or equivalent in Blue star/Nirali.

S&F as in repair Harrison rails 20 mm dia ,anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc complete all as specifed and directed .

Roughening surfaces of old concrete floor/terrace by picking including taking down existing detoriated / decayed tar felt or any treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 1000 metre, complete all as specifed and directed .

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed. Note:- The WPC shall be measured and paid separately under respective items of Sch "A" BOQ.

Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane for approachable roofs with One layer of APP based polymeric membrance minimum weighing 3 Kg/ Sqm & minimum 3 mm thickness reinforced with polyster non woven fabric (wt not less than 150 gms/ sqm) laid on primed surface by forced application complete all as specified. with lap of 100 mm and the over lap shall be sealed by flame

M&L for applying A coat of hot blown bitumen grade 85/25 @ 1.2 Kg / Sqm shall be applied over polymeric membrane and blinded with clean dry sand at the rate of 0.05 Kg per Sqm as per manufacturer instruction .

M&L for 15 mm thick screed bed or bedding layer in CM 1:4 mixed with water proofing compound @ 3 % by weight of cement on top of membrane surfaces to recieving PCC tiles surface etc complete all as specified and directed.

S&F Precast machine pressed of grey cement concrete tiles of size 250mm x 250mm x 20mm to 22 mm or 300mm x 300mm x 20mm to 22 mm conforming to IS 1237 shall be laid over cement screed bed, the joints between the tiles will be 2 to 3 mm thick and filled with polymer base joint filler of approved quality complete all as specified and directed.

M&L cement concrete in roof kerbs, mud stops or coving (rounded or chamfered) on edges as directed PCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate complete all as specified and directed

M&L 75 mm thick cement concrete 1:3:6 type C-2 ( 40 mm graded aggregate) as in subbase for laying floor finishes complete all as specified and directed

Dismantling of plain or corrugated steel sheeting, any gauge, thickness complete all as specified and directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based Mangalore pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws asspecified complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and directed.

M & L rendering 15mm thick on concrete/ brick surface of wall in cement mortar 1:4 finished fair and even smooth without using extra cement complete all as specified and directed.

M & L Preparing new plastred surfaces of walls and applying two coat of Cement based paint over and including coat of primer complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete unreinforced complete all as specifed and directed.

M & L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregates as in sub base, complete all as specified and directed.

M&L Vitrified tiles coloured ceramic heavy duty deisigner tiles of size 400 mm X 400 mm X 12 mm chequered set , jointed and pointed in neat cement slurry as in floors with grey cement over and including 15 mm thick screed bed or bedding layesrs in CM 1:6 complete all as specified and directed. Make : Johnson Endura premium quality or other equivalent makes as approved by GE.

M & L coloured Rubber Moulded Chequred Cement Concrete tiles 300 x 300 x 25mm thick, of glossy finishes set jointed and pointed in neat cement slurry in floors with colour cement and pigment over and including 15 mm thick screed bedding layers in in CM 1:6 complete all as specified and directed

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

M&L for cement concrete 1:4:8 Type D-2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for Rendering 10 mm thick on fair faces of concrete /brick surface in cement mortar 1:4 With water proofing compoung and finished even and smooth without using extra cement as in Internal wall complete all as specified and directed. Note:- WPC shall be measured and paid separtily.

M & LFormwork to faces of walls,retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. complete all as specified and directed.

M & L for RCC 1:2:4 Type B1 using 20mm graded crushed stone aggregates as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well raming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated materials exc 500 mtr but nexc 1.5 km & depositing where directed at level n. exc. 1.5m above the starting point. complete all as specified and directed.

Taking down of carefully unservicaible Aluminium/copper point wiring (light, fan socket or power) complete with fitting such as switches, ceiling rose lamp holder, sockets, fan regulators, SK/FTL light fittings etc removing materials for store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc as per existing finishing complete all as specified and directed.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles GI screws, rawal plugs in ceiling or roof if not possible including Tee, Junction boxes and provision of flush metal boxes, inner and outer plate suitable for modular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan point controlled by one Switch.

All as per Srl item No 118 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on same board with other switches omplete all as specified and directed.

All as per Srl item No 118 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board.omplete all as specified and directed.

All as per item No 118 above for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete..

All as per item No 118 here in before above but one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one metal clad socket outlet point controlled by one MCB complete.

All as per Srl item No 118 above but point wiring for one bell/buzzer point controlled by one push button on the same board with other switches or independent omplete all as specified and directed. Note for item 118 to 123 here in before : (i) The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc. for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at RCC Columns/Beams/Ceilings shall be in surface conduit of suitable size fixed on surface with using PVC rawl plugs . (ii) Rate for modular metal flush boxes ,inner and outer plate with frames are deemed to be included in the quoted rate by contractor for above items. (iii) Fittings like Modular switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iv) The size of conduits shall be determined on permissible No. of runs of wires as specified in SSR Part-I (2009) clause 19.125 (B). However minimum size of conduit shall be 20mm dia (Medium grade (v) Make of cable : Finolex /Havells/ Poly cab as approved by GE.(vi) Make of PVC conduit & fittings : AKG / Asian /Plaza/Jindal /Avon/Finolex/National /Kalinga as approved by GE.

S&F Modular switch piano single pole one way 6 amp complete. Make -Legrand / Anchor Penta / Crabtree/MK/HPL as approved by GE.

S&F Modular switch piano single pole one way 16 amp complete. Make - Legrand / Anchor Penta / Crabtree/MK/HPL as approved by GE.

S&F Modular bell push, 6 amp 240 volts complete. Make - Legrand / Anchor Penta / Crabtree/MK/HPL as approved by GE.

S&F door bell, AC, 240 volts, single pole complete. Make - Legrand / Anchor Penta / Crabtree/MK/HPL as approved by GE.

S&F Modular socket outlet 2/3 pin combined 2 module 6/16 amp complete. Make -Legrand / Anchor Penta / Crabtree/MK/HPL approved by GE.

S&F Modular socket outlet 2/3 pin combined 2 module 6 amp complete. Make -Legrand / Anchor Penta / Crabtree/MK/HPL as approved by GE.

S&F ceiling rose 3 plates polycarbonate, isolated body complete. Make - Legrand / Anchor Penta / Crabtree/MK/HPL as approved by GE.

S&F modular fan step regulator 120 W 2 module complete. Make: Legrand / Anchor Penta / Standard/Crabtree as approved by GE.

S&F in replacement of UNSV fluorescent tube light fitting batten with universal batten fitting with single T8 LED lamps complete all as specified and directed. Make: C&G or other euivalent from in Philips/ Havells/CG as approved by GE.

S&F in replacement of UNSV LED mirror light fitting, 10 watts, 1000 lumens 6500K comprises of aluminium extruded channel, frosted diffuser, integrated electronic driver, IP 20 protection and all accessories pre- wired including connecting to mains complete all as directed. Make- C&G/Havells/Phillips as approved by GE.

S&F in replacement of UNSV bulkhead fitting with integrated LED bulk head fitting 600 lumens, 6000 K comprises of pressure die cast housing, acrylic diffuser and frame IP 65 protection, IK-07 etc including connection complete all as directed.Make- LBHP-10-CDL of C&G or other equivalent makes from in Havells/Phillips as approved by GE.

S&F in replacement of UNSN Decorative, Wall mounting champagne gold finish fixture with plastic body along with 9 W LED lamp B22 base as per Havells cat ref no. LHFOECE1TZ1O014 or other equivalent makes from Philips/C&S as approved by GE.

Dismantling and taking out existing unsv roadway light fitting of any type and in any position on walls/ poles and Supply , fixing and testing in 20 watt LED roadway street light made up of pressure die cast aluminium housing complete with polycarbonate cover with high impact resistance 15 W- 1500 lumen with efficiency of 100 lumens/ watts at system level, ingress protection of IP- 66, PF-0.9 & with input resistance,ie IK 07 surge protection upto 4 KV, compiled with IS 10322 CCT is greater than 5000K complete with all accessories duly pre-wired, including supply and fixing the bracket of 40 mm dia 60 cm long GI pipe light grade ,bent to shape including MS FI clampsof 20/25 x3 mm, nut and bolt and connected with flexible cable 3 core copper conductor 0.50 sqmm upto ceiling rose, mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed. Make: Cat pt No. ENDURAPEARLSL15WLED757SASYTOPCMP of Havells or other equivalent of C&G/Phillips/C&S as approved by GE.

S&F in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole and neutral MCB 20 amp,240Volts power coated CRCA steel sheet enclosure recess mounted with chained metal cover for the socket outlet with and including one number single pole 'C' series MCB 16/20 amp as required. Make of MCB SP 16/20 Amp- Cat Pt No. 811126/27 of IndoAsian orequivalent in Legrand/Seimens/Schneider Make of SPN DB with MCB 20Amp - CAt PT No 811956 of Indo Asian or other equivalent in Legrand/Schneider as approved by GE.

Taking down carefully energy meter any type, any capacity after disconnecting and refixing / connecting the same after complete of rewiring of Bldg/Qtr complete, all as specified and as directed by GE.

M&L in replacement UNSV of sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 6 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 25 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 4 Sqmm as earth continuity conductor complete all as specified and directed.

M&L in replacement UNSV of sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 4 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 20 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 2.50 Sqmm as earth continuity conductor complete all as specified and directed. Notes for item No. 139 & 104:- (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc. for concealing the conduits to required depth & making good the disturbed surface in cement sand mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling/RCC surfaces shall be in surface conduit of suitable size fixed on ceiling/RCC surfaces with using PVC rawl plugs) (iii) Make of cable : Plaza /Finolex /Havells/Shalabh/ Polycab/HPL/L&Tas approved by GE. (iv) Make of PVC conduit & fittings : AKG / Asian /Plaza/Jindal /Avon/Finolex/National /Kalinga as approved by GE. )

M&L in replacement UNSV of sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 10 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 32 mm dia with standard accessories along-with two run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 6 Sqmm as earth continuity conductor wall/ ceiling/concealed surface etc complete all as specified and directed.

Notes for Item 27 here in above : (i) Two run of single core PVC cable with two run of earth conductor and one run of conduit shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc. for concealing the conduits to required depth & making good the disturbed surface in cement sand mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling/RCC surfaces shall be in surface conduit of suitable size fixed on ceiling/RCC surfaces with using PVC rawl plugs) (iii) Make of cable : Plaza /Finolex /Havells/Shalabh/ Polycab/HPL/L&Tas approved by GE. (iv) Make of PVC conduit & fittings : AKG / Asian /Plaza/Jindal /Avon/Finolex/National /Kalinga as approved by GE. )

S&F in replecement of UNSV vertical type load line distribution board ,double door, 4 way, AC 3 Phase 415 volt with TPN bus bar 250 Amps for each phase with 2 Neutral bar, 2 Earthbar and cable ties for cable management,fully insulted busbar & shrouded Neural bars ,improved Pan assembly for each insullation ,prefitted masking sheeet,reversible door for IP 43-"IK 09 with metal door with provision for DPX3 100 amps isolator as incomer and SP/TP MCB's as out going complete all as specified and directed by Engr-in-Charge. Make of VTPN DB:-IndoAsian cat Part No-811896 or equivalent make in Havells/L& T. Make of MCCB:- IndoAsian Cat pt No. 830295 or equivalent make in Havells/L& T

S&F in replacement of UNSV MCB distribution board SPN, 240 volts, 12 ways ,powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 42- IK-09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with following ratings & ways:- Note: (i) MCB’s /Isolators etc. shall be measured and paid for separately under appropriate item of Sch ‘A’. Make: Legrand or other equivalent in Havells/L&T/Schneider/ IndoAsian as approved by GE. Note for Item No.142 to 143:- (i) Fittings like MCB’s /Isolators etc. shall be measured and paid for separately under appropriate item of Sch ‘A’. (ii) -Sheet steel enclosure to be fixed flush to wall by cutting niche & make good to the disturbed wall surface as per existing (iii) Rate for Incomer MCCB is deemed to be included under above item.

S & F in replacement of unserviceable MCCB 4 pole ,100 Amps Complete all as specified and directed. Make- IndoAsian cat part No. 830272 or equivalent in seimens / Schinder/ IndoAsian as approved by GE .

S & F in replacement of unserviceable MCB DP 240 volts 'C' Curve suitable for fixing in MCB DB of capacity 63 amps complete all as specified and directed. Make - IndoAsian or other equivalent in Hager or Schneider as approved by GE.

S & F in replacement of unserviceable MCB SP 240 volts 'C' Curve suitable for fixing in DB of capacity 6 to 32 Amps complete, all as specified.Make -IndoAsian cat ref no 811122/24/26/27/28/29 or other equivalent makes for Hager Schneider as approved by GE.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (1991) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. NOTE : RCC pit cover shall be pre-cast of RCC (1:2;4) type B-1 80 mm thick reinforced with XPM weighting not less than 4 Kgs/Sqm in lieu of CI cover.

Disconnecting and taking out existing unserviceable light fitting of any description and in any position on poles and S&F 20W LED Post top lantern complete accessories to be fixed on pole/wall including connecting the fitting to control switch at the bottom of the pole with using 2.5 Sqmm two single core PVC insulated and unsheathed copper conductor copper conductor cable complete all as specified and directed . (Make-Crompton Cat NoLPTH-20-CDL or equivalent model of make Havells/C&S).

Taking down old unserviceable MS junction boxes from the pole with disconnectiong all connections, Supplying and fixing in position new Pole box made of thermoplastic Polycarbonate having IP65/IP66 degree of protection (shock proof, dust proof, jet water proof and acid resistive). The gasket should be internally embedded, and made of Polyeutherene. The boxes shall be tested as per IEC 60670-2/ 60670-22. The boxes shall have self threaded holes & provision for mounting din rail. The lid should be hinged type with sealing screw. The screw should be of stainless steel so that there is no corrosion. The boxes should withstand temperature of -40c to +120c. The glow wire test should be conducted at 960 c or 750 c and material should be flame retardant & self extinguishing. UL subject 94, V-0. The boxes should be free from toxic substances like hal ogen and silicon. The boxes should have suitable pre-moulded knock out /or plan wall depending on requirement. Box dimension shall not be less than 200 X 160 X98 MM (LXBXH). Box shall be suitable for 16/25Sqmm cables including one no. MCB SP 230 volts 6 amps of make Havells/Legrand/ABB and connecting the bus bars to cables with using suitable GI nut, bolts and washers and aluminum lugs etc fixed on pole using 30x5mm FI clamps,nuts,bolts & washers complete all as specified and directed. Make: Hensel/GE/Legrand as approved by GE.

Material & labour for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches/ducts for cable protection complete all as specified and directed (NOTE : Thickness after punning shall be measured for payment)

M&L for old size sub class `B` bricks, kiln burnt, as in cable protection laid flat with axis of brick perpendicular to the axis of the cable complete all as specified and directed .

Disconnecting and taking out old existing unserviceable/ non- functional LT Cable of size 35 Sqmm 3.5 core of any description and in any position from trench/duct/pipe etc complete and Supply,laying, jointing & testing XLPE insulated PVC sheathed (heavy duty) armoured cable with aluminium conductor for working voltage upto 1100 volts of size 35 Sqmm 3.5 core .complete all as specified and directed. Make- Gloster/Havells/Polycab or equivalent.

M&L for providing cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in copings, holdfast and the like including weathering, slightly rounded or chamfered angles and throating no road etc as directed with and including necessary form work complete, all as specified and directed by Engr-in-charge.

Supply and installation of air cooled inverter based 5 star rating split AC unit with both heating (Auto defrost) and cooling functions, Air conditioner electric driven single phase of capacity 2.0 TR with charged with Eco friendly Refrigerant R410/R32 and comes with special health filter and all connected accessories and copper tubing from indoor to outdoor and making of hole in any type of wall, including PVC drain pipe from indoor unit upto plinth protection of building , Outdoor split AC hanging wall mounted stand and flexible PVC casing pipe minimum 40mm dia covered on all exposed copper insulated pipe line and PVC wire including taking down old split AC/window type AC complete set of indoor and outdoor AC with rusted Stand with connected accessories etc complete all as specified and directed by Eng-in-charge. Make: Voltas / Hitachi/ LG. Note:- Old retrieved all item of ACs will be property of department and deposited to MES sore yard of AGE E/M direct complete all as specified and directed .

S&F MCB distribution board powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100/63 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with rating DB 8 Way 240 volt single door complete all as specified and directed by Engr-in-charge

M&L for sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size16 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 25 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 6 Sqmm as earth continuity conductor complete all as specified and directed.

M&L for sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 6 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of suitable dia not less than 25 mm dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 6 Sqmm as earth continuity conductor complete all as specified and directed.

S & F MCB DP 240 volts 'C' Curve suitable for fixing in MCB DB of capacity 63 amps complete all as specified and directed. Make - IndoAsian or other equivalent in Hager or Schneider as approved by GE.

S & F MCB SP 240 volts 'C' Curve suitable for fixing in DB of capacity 6 to 32 Amps complete, all as specified.Make -IndoAsian cat ref no 811122/24/26/27/28/29 or other equivalent makes for Hager Schneider as approved by GE.

Supply and fixing metal clad box with plug and top 3 pin, 20 Amp capacity complete all as specified and directed. Make : Standard / Havells / C & S Electrics/ Siemens

S&F Exhaust fan AC Single phase 230/240 V of size 300 mm sweep with louver complete all as specified and directed by Engr- in- charge.

Supplying, laying & jointing of water tubing, 25 mm bore, light grade as in sleeving etc laid in trenches / ducts etc. complete all as specified and directed by Engineer-in-Charge.(MAKE : TATA/JINDAL/TT SWASTIK) as approved by GE.

Supplying, Laying, testing and commissioning of UNSV XLPE insulated,IS 7098 (Part-I)-1988 marked screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor 1100V grade cross section area 6 Sqmm 2 core cables laid in trenches/fixed on pole/wall / passed through pipe including making necessary connection, with busbar/MCCB/DB's & testing complete, all as specified and directed by Engineer-in-Charge. Make:Havells/CCI/ICL/GLOSTER/Incab/Nicco/Polycab/Plaza) (NOTE: Earth work, sand cushioning, GI pipe and brick protection shall be measured and paid separately )

Supply, laying, connecting & testing of galvanised iron water tubing 'medium grade' of size 25 mm dia complete, conforming to IS-1239 with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc as required complete fixed to walls and ceilings, laid in trenches/under floor/under road or floors complete all as specified and directed by Engr-in-charge. Note:-(i) Earth work in excavation, returning filling in and removal & GI fitting shall be measured and paid separately under appropriate items of Schedule ‘A’

Supplying, installation, commissioning & testing single phase electric driven, self-Priming mono block centrifugal pumping set having discharge 36 to 8 LPM at 19 to135 Feet head, with bronze impeller and SS casing, shaft with electric motor single phase, 240 volt AC of suitable capacity of 1 HP mounted on common base plate / MS channel and PCC foundation of suitable size as per manufacturer recommondation including jointing with delevery & suction with required Jointing material all as speedfied and directed.Make : Kiloskar/crompton

JS CONSTRUCTION COMPANY

M/S P K ARORA

OM TRADERS