THRISSUR CORPORATION KKY ZONAL DN43-AMRUT 2.0 Water body rejuvenation-Herbert nagar kulam Kadam kulam

Amount

DAR CIVIL

15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

OD543580/2024-2025:Clearing light jungle up roooting of thick vegetation & small trees of girth up to 30cm & removal of rubbish up to a distance150m out side the periphery of the area cleared.

OD543581/2024-2025:Removing chandy ,kulavazha and all other vegetation including cost and conveyance etc.complete with mechanical means.

OD4238/2025-2026:60.2.2.Baiing out water Using 5HP Pump-Bailling out water with 5HP engine and pump set including conveyance to site and errection cost of fuel,lubricationoil and other store of pay of staff etc.complete

OD543582/2024-2025:Earth work excavation in or under water by mechanical means[Hydraulic excavator]/manual means over areas including disposal of excavated earth lead up to 50m.and lift up to 1.5m. disposed earth to be levelled and neatly dressed.All kinds of soil.

OD17370/2025-2026:60.7.3. DISMANTLING DR - Dismanling , clearing away and carefully stacking materials useful for reuse for any thickness of walls in DR masonry including disposal of debris within a distance of 150m.

OD17366/2025-2026:DR with Departmental Stone . DRY RUBBLE MASONRY- Dry rubble witout concrete levelling course using departmental rubble including packing to compactness to lines and levels.Labour charges etc. complete as per direction of Departmental officers at site.

OD17371/2025-2026:60.7.1. DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

13.33.1:Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

9.48.1:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.3:Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15<sup>0</sup> landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.22A.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

OD9609/2025-2026: Providing&fixing precoated galvanized iron profile sheets[size,shape and pitch of corrugation as approved by Engineer in charge]0.35mm[+0.05%]total coated thickness with zinc coating 120gms per sqm as per IS;277,IN 240mpa steel grade ,5-7microns epoxy primer on both side.of the sheet and polystertop coat 15-18microns.Sheet should have protective guard filmof 25 microns minimum to avoid scratches during transportatioon & should be supplied in single length up to 12m or as desired by Engineer -in-charge.The sheet shall be fixed using self drilling /self tapping screws of size[5.5x55mm] WITH epdm sealcomplete upto any pitch in horizontal/verticalor curved surfaces,excluding the cost of purlins ,rafters and trusses &including cutting to size and shape whereever required.

OD9615/2025-2026:Ridge caping with painted galavanized steel sheets 0.35mm thick including all cost of materials,conveyance,labour charges etc. complete.

OD9618/2025-2026:Supplying and fixing 150mm dia PVC rain water gutter semi circular section including fitting with 32mm*5mm flat supporters at 1m interval etc.complete

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

OD9738/2025-2026:Supplying and fixing at site aluminium composite panels of Alucobound, Durabuild or equivalent make and approved colour certified for exterior applications including 15 years guarantee for colour fastness of clear thickness 4mm, with 28 to 30 microns of PVDF coating conforming to ASTM standard on the top aluminium skin of 0.2mm and with a bottom aluminium skin of 0.25mm with service& lt;br&amp:gt:coating of polyster paint, laminated on to a center core of 3.5mm of single recycle low density polyethylene material<br>

51.2.3:Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

OD54015/2023-2024:Providing and laying 60mm thick factory made cement concrete inter locking paver block of M30 grade made by block making machine with strong vibratory compaction of approved sizedesign and shape laid in required colour and pattern over and including 50mm thick compacted bed of coarse aggregate filling the joints with fine sand etc.all complete as per the direction of engineer-in-charge.

10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

10.25.2:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD13530/2025-2026:Supplying and fixing stainless steel letters of 15 - 30 cm size (Malayalam/ English)

OD13531/2025-2026:Providing and fixing name board wit granite of any colour 18mm thick including engraving letters etc. Coplete

OD17438/2025-2026:Laerite cladding tile of required size in c.m. 1;4 including all labour charges etc complete.

JOSHY K.P (BID ID -2218127)

Bidder Name

t.l. rappai

JOSHY K.P