SPECIAL REPAIR TO BLDG NO T-239 OR MD ACCN AT MIL STN KANCHRAPARA UNDER GE BARRACKPORE

Amount

PART-I Taking down chowkats with shutters (without taking off shutter from the frames) exceeding 1.50 Sqm and not exceeding 4.00 Sqm each complete all as specified and directed.

Taking down chowkats or frames (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down all existing roof treatment and demolition of cement concrete padding/levelling course incl wire brushing and cleaning loose dust etc from surfaces of RCC roof incl flashing and junction of parapet complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone or concrete surface of wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlars facing dressed stonework & precast concrete articles complete all as specified and directed.

Demolition of (reinforcement cut as required to facilitate demolition) cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete in ground floor, (unreinforced) paving not execeeding 15cm thick(below or above GL) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards, any thickness including cover fillet complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc.) sheets in roof coverings complete all as specified and directed.

Demolition and breaking up drain pipes(Salt glazed ware, AC or Reinforced concrete) set in cement mortar( internal dia of pipe in 300mm) complete all as specified and as directed.

Roughening of surfaces of old concrete floor/slab by wire brushing, sweeping, cleaning and washing down to remove all loose dust etc. and brushing neat cement slurry @3.00kg/ square metre on etc complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as filling in pressed door chowkat/hold fast blocks etc complete all as specified and directed.

M&L for providing Reinforced cement concrete (1:2:4) type B-1(using 20mm graded aggregate) as in shelves and the like complete all as specified and directed.

M&L for precast reinforced cement concrete (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in cover slab of drain/manhole set in cement mortar (1:6) complete all as specified and directed. (NOTE: Cost of Form Work is deemed to be inclusive of unit rate quoted by the contractor & reinforcement shall be measured & paid Separately.)

M&L for brick work with sub class 'B' bricks locally available best quality bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for half brick work with sub class 'B' bricks locally available best quality bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

Supply only integral water proofing compound liquid, ISI marked complete all as specified and directed.

Providing formwork to the soffits of suspended slabs such as roof slabs, floor slabs, landings, shelves and similar work, not exceeding 200 mm thick (horizontal or sloping ) and making flat, rough finished surfaces of concrete complete all as specified and directed.

S&F of second class hard wood in fillets, square, rectangular or triangular in section, clean swan, fixed with nails or brads, sectional area exceeding 13 sqcm but not exceeding 25 Sqcm complete all as specified and directed.

S&F of 35 mm thick flush door shutters (factory made) solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F for 35mm thick glazed and skeleton shutters of second class hard wood open rebated and prepared to receive gauge glass etc(without sash bars) edgs of framing plain chamfered or rebated fitted with cut and mitred beads for scuring glass etc size of members of shutters as specified in relevant clause of section 8 clause No. 8.24(a) of SSR Part I design, etc complete all as specified and directed.

S&F for 18/19 mm thick veneered finish prelaminated particle board fix in cupboard shelves & shutter interior grade, prelaminated in one side with decorative choice lamination solid core medium density general purposes, and other side white lamination fixed with screw including teakwood lipping all round complete all as specified and directed.

S&F mild steel door shutter two leaves with frame of 0.80 guages MS sheet(all around) and leaves of 21 gauge MS sheet with three way of locking arrangement with brass lock and CP handles with duplicate keys including tow coats of spray paint over a coat of red oxide primer all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification & drawing as mentioned in SSR Part-II (2020), Section 8, Page No.174 complete all as specified and directed.

S&F of factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube as per specification and drawing as mentioned in SSR Part-II (2020), Section 8, Page No. 178 complete all as specified and directed.

S&F of 300 mm aluminum alloy, anodised, sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F of aluminium, anodised, barrel tower bolts of extruded section and fixed 150mm long, confirming to IS-204 (Part 2) : 1992 complete all as specified and directed.

S&F of aluminium handles, cast type, anodised 150mm long, confirming to IS-208 : 1996 complete all as specified and directed.

S&F for 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F of stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete all as specified and directed.

S&F of TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L of mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 complete all as specified and directed.

S&F of pressed steel frames for door of size 125mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded aggregate)including applying of two coats of black bituminous paint (shop coat) to back of chowkats complete all as specified and directed.

S&F of pressed steel frames for door of size 105mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded aggregate)including applying of two coats of black bituminous paint (shop coat) to back of chowkats complete all as specified and directed.

S&F powder coated anodised aluminium alloy sections 3 tier track sliding windows series B weight of section frame 1.248Kg/m and shutter section weight 0.547 kg/m jindal or equivalent duly fitted with neoprene beading, glazing clips, tinted glass panes 5.0mm nominal thickness, aluminium wire cloth 0.45 mm dia and average width of aperture 1.4mm, aluminium alloy handles etc complete all as specified and directed. (Note : Rate shall include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc.)

S&F powder coated anodised aluminium ventilator with fixed aluminium frame of size 65x40x1.98mm thick or equivalent section fixed in vertical position with aluminium vertical members and half portion to be approved with 4mm thick pin head glass and remaining protion to be ouvered using 4mm thick pinhead glass and louvered porition covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm incl necessary channel frame work, including rubber gasket and aluminium beading, and make completed all as specified and directed. (Note : Rates shall include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading etc.)

M&L for 10mm thick rendering in CM 1:3 over concrete surfaces(roof) mixed with liquid water proofing compound @200ml/50 Kg of cement complete all as specified. (Note :- Liquid water proofing compound shall be measured and paid for separately as " Supply Only".)

M&L for applying roof treatment on top of roof with APP modified membrane( minimum 3mm thick) weight not less than 3.00Kg/sqm and reinforced with non-woven polyser reinforcement/mat (centre core) with thermal insulation with polythene finish on upper side of membrane, laid by torch application method with overlaps 150mm on length side and 100mm on th width side as per manufacturer's instructions over a coat of approved cold applied bituminus oil based primer(IS-3384) @300gm/sqm and applying tow coats of aluminium paint 0.20litre/sqm (APP should be applied by authorized applicator) complete all as specified and as directed by Engineer-in-Charge.

S&F of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in wall/cladding, fixed with self tapping screws complete all as specified and directed.

S&F of false ceiling with exposed metal (PPGI) framework/ “Tee” Grid providing and fixing of suspended Tee grid false ceiling using “T” Grid System – powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mm x 600mm with main runner 32 x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40mm thick using 6mm thick non asbestos fibre cement board of size 595 x 595mm, an asbestos Free fibre cement board manufacture using high Pressure System Curing technology. T grid Framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more that 300mm from the adjacent wall. 1220mm/600mm Cross Tee to be interlocked between main runners @ 600mm c/c, so as to from 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 & type B category III of ISO 8336, tested as per AS 1530 part – 3 & B. S- 476 part 4,5,6,7 & 8 should be placed in Grid module to form complete all as specified and directed.

M&L for 25mm thick cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in levelling course of floor complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in sub base/plinth protection & hard standing including finishing the cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L filling PCC type E2 (1:5:10) (40mm graded stone aggregate) as in sunken floor after applying appropriate treatment to side walls complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing compound @200ml/50Kg of cement in bottom of sunken floors complete all as specified and as directed. (Note : WPC shall be measured and paid for separately)

M&L for 18-20mm thick machine cut kota stone slab flooring (pre-mirror polished) over and including 20mm thick screed bed of cement mortar (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab in riser of steps, skirting, dado and pillar laid over and including 10mm cement plastering in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick mirror polished, high gloss finish Granite (absolute Jet / telephonic black) work in jambs / soffits, window-cills, basin / kitchen platforms, kitchen shelves, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl necessary making holes for fixing hinges, bolts, requisite adhesives/epoxy for pasting, etc complete all as specified and dirtected.

M&L for pre-polished coloured chequered cement concrete tiles 30cm x 30cm x 25mm thick (glossy type), set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and including 20 mm thick cement screed bed in cement mortar (1:6) complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured tiles of 8mm to 10mm mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tiles over and including 15mm thick screed bed or beading layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

Ditto all as per item No.51.00 here in above but in verticle surface including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface of size 450 mmX 350 mmX7 mm thick or equivalent set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering of cement mortar (1:4) complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick work or concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar(1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on brick, concrete surfaces in cement mortar (1:4) mixing with WPC @ 200 ml /50 Kg of cement or as per manufacturer's instructions, finished the surfaces even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately)

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays for 100mm bore of pipe, including bolts and nuts and securing ends of stays to wall or roof etc complete all as specified and directed.

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls by using chesel/hammer. Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement clean loose rust from bars manually with brush fixing new supplymentary bars if required, either by tying it with existing bars or by welding on it. Applying eppoxy bonding agent and making good with polymer modified plaster/ micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including formwork complete all as specified and directed.

S&F of stainless steel kitchen plate rack fancy type fixed with plug washer and or including fixing cantilever brackets and overall size 900X800 mm complete all as specified and directed.

S&F of brass CP Sink mixer long head with movable neck, fixed to wall, for mixing hot and cold water screwed down for iron pipe and fixed and joint with adhesive, taflon tape, etc complete including taking down old unserviceable CP sink mixer complete all as specified and directed.

M&L for 3mm thick of wall care putty on newly plastered surfaces including preparation of surface and applying two coats of oil bound distemper using AUTO-ROLLER and AIR-LESS paint Sprayer complete all as specified and directed.

M&L for complete removal of existing treatment and levelling of wall surface using MECHANICAL/ELECTRICAL OPERATED SANDING/SCRAPING MACHINE WITH INBUILT VACCUM SUCTION system to suck the existing treatment as retrieved by scrapping/sanding etc and applying one coat of water proofing wall care putty of 3mm thick for obtaining smooth paintable surface complete all as specified and directed.

M&L cleaning vertical and horizontal surfaces of sunken slab using wire brushing followed by sanding with emery paper for loose materials/dust and applying two coats of epoxy resin component (Dr. Fixit DAMPGUARD or equivalent) solution/mix using nylon brush pouring Base part in atttain homogeneous smooth paste and dilute the mixed compound with water in ration 1 part Base: 1 part Harder : 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, first coat will be allowed to dry for 6 to 8 hrs before application of second/fianl coat) including curing treated surface for 24 hrs complete incl applying evenly a coat of blown [email protected] kg/sqm over entire treated surfaces incl spout holes complete and all as specified as per manufacurer instruction.

M&L complete removal of existing treatment distempered and painted surface and applying one coat of oil emulsion distemper on walls / ceiling using AUTO-ROLLER and AIR-LESS paint Sprayer complete including cornices, pilasters etc over and including 3mm thick of wall care putty complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer after preparation of new wooden surfaces of any description over 10 cm girth or width complete all as specified and directed.

Material & Labour for applying two coats of 100% Premium acrylic emulsion paint(using AIR-LESS PAINT SPRAYER) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over wall surfaces by using AIR-LESS PAINT PRIMER SPRAYER including preparation/levelling of old surface of wall using manual sand papers(where reqd) of approved grade complete all as specified and as directed.

S&F in repairs of brass chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flanges complete all as specified and directed.

S&F in repairs of 15 mm angle cock/stop valve, fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of 15mm dia brass CP wall mixer for mixing Hot and Cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs of soap dish, chromium plated, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs of 25mm dia (heavy duty) stainless steel, single curtain rod (wall thickness not less than 1mm) including funnels, brackets, stops etc suitable for single curtain rod, fixed etc complete all as specified and directed.

Taking down old unserviceable 15mm dia GI pipe complete as specified and as directed.

Taking down old unserviceable 20mm dia GI pipe complete as specified and as directed.

S&F of 20mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, concealed joint with CPVC adhesive taflon tape complete to walls and ceilings or laid in floors including all connected brass CPVC fittings and cutting grooves, filled with Cement mortar(1:6) complete all as specified and as directed.

S&F of 25mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, concealed joint with CPVC adhesive taflon tape complete to walls and ceilings or laid in floors including all connected brass CPVC fittings and cutting grooves, filled with Cement mortar(1:6) complete all as specified and as directed.

S&F in repairs Vitreous China wash basin with matching pedestal, standard height, white, flat back, size 550x400mm, including cutting for and pinning in ends of brackets or erecting stand but inclusive of fixing of supply waste pipe complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes single socketed (IS-13592-1992 type 'B') in any length with rubber ring joints fixed to wall or laid in trenches or in floor including taking down old unserviceable PVC pipe with all fittings complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) pipes single socketed (IS-13592-1992 type 'B') in any length with rubber ring joints fixed to wall or laid in trenches or in floor including taking down old unserviceable PVC pipe with all fittings complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal provided with access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F in repairs of 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs of 15mm dia bib taps (suitable for 20mm outerdia CPVC pipe) fancy type, cast copper alloy with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferule, chromium plated with long screw type fixed complete all as specified and directed.

S&F of brass CP Central hole basin mixer for mixing 'HOT & COLD' water screwed down for iron pipe and fixed and joint with adhesive, taflon tape, etc complete including taking dwon old unserviceable CP basin mixer complete all as specified and directed.

S&F in repairs of 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia suitable for low level cistern fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S&F in repairs of vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests with P or S trap (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe etc complete including making good to floors with PCC bedding (1:5:10) type E-2 using 40mm nominal brick ballast and connection to trap with cement mortar, and making good to floor complete all as specified and directed.

S&F in repairs of 32mm dia waste fittings, brass chromium plated for glazed ware sinks, basins etc. with long screwed shanks & fly nuts, flanged end bedded in red lead cement & other end fixed complete all as specified and directed.

S&F in repairs of 15 mm dia PVC connection pipe of length 600 mm with PTMT nuts complete all as specified and directed.

S&F in repairs of Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

Dismantling water tank of capacity exceeding 250 & not exceeding 500 litres and removing to store complete all as specified and directed.

S&F of rotational moulded polyethylene water storage tanks 500 litres capacity (cylindrical vertical with closed top three layer) hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F in repairs of 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed (minimum weight 210 gms) complete all as specified and directed.

S&F in repairs sink made of 1mm thick stainless steel sheet, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever GI brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm alongwith 40mm waste fittings brass, chromium plated complete all as specified and directed.

PART-II Excavation in trenches for laying under ground cable, foundation and erection of poles and stays in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out complete all as specified and directed.

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25cm soil all as specified and directed.

Removing surplus excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting points as in soft/loose soil all as specified and directed.

Disconnecting the electrification and taking down old DBs( any type of vertical load line/TPN/SPN DBs including MCB any type & capacity) and making good to the disturbed surfaces to match the existing surfaces complete all as specified and directed. (Note: Temporary power supply shall be provided by the contractor)

Taking down unserviceable submain wiring aluminium etc and making good the disturbed surfaces of walls/floor etc matching with the existing surface.

Taking down old unserviceable existing service/UG cable all as specified and directed.

M&L for disconnecting electric supply, taking downfan, sealing cable ends, dismantling blades ceiling fan any size from existing position and bringing to MES yard for cleaning all dust, oiling and greacing and hanging only ceiling fan and connecting up including provision of cable from ceiling rose to fan complete all as specified and directed. all as specified and as directed by EIC.

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, light fittings and including making good the disturbed surfaces to match with the existing surfaces by applying white/ colour wash/distemper over applying of putty for smooth finish surface complete all as specified and directed.

M&L for point wiring complete with 1.5 sqmm PVC insulated, FR-LSH type, ISI marked, conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories concealed in walls / roofs / floors / ceiling etc. flush mounting MS box with top, bottom, side/back wall knockout for conduit entry from any direction made out of 1.60mm thick and 50mm depth suitable for fixing of modular top cover , blanking plate as per numbers of switch modules, modular switches, sockets, fan regulators, red colour indicator, blank plates etc as approved coloures modular accessories of suitable modules and including 1.5 Sqmm PVC insulated multistranded FR-LSH type unsheathed single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surfaces by applying white/colour wash/distemper as applicable after applying of putty for smooth finish surface complete all as specified and directed for the following:- (Note:- (i) All necessary accessories such as blank plate, MS box, screws, washers etc are to be used of same make/brand only in relevant items. (ii) Cutting & chasing of wall for point wiring at any height shall be done and cost of the same deemed to be including with quoted rate.)

One light point controlled by one switch.

One light point controlled by two way switches.

One ceiling fan/exhaust fan point controlled by one switch.

One 3 pin socket outlet 5 Amps on the same board.

One bell/buzzer point controlled by one push botton.

One 3 pin socket outlet 5 Amps on the independent board.

All as per item No.108.00 above but 2.5 sq mm multi stranded copper conductor with 2.5 Sqmm copper earth continuity wire connected to earth duly complete for one 15A socket on independent board all as specified and as directed.

S&F of switch piano flush button single pole one way 5/6 Amp 240 volts, AC, ISI marked complete all as specified and directed.

S&F of switch piano flush button single pole one way 15 Amp 240 volts, AC, ISI marked complete all as specified and directed.

S&F of switch piano flush button single pole two way 5 Amp 240 volts, AC, ISI marked complete all as specified and directed.

S&F Socket outlet, flush type 2 in 1, 5 pin, 5 Amps, 240 volts all as specified and as directed.

S&F Socket outlet, flush type 2 in 1, 3 pin, 5 and 15 Amps, 240 volts all as specified and as directed.

S&F of ceiling rose, surface bakelite 65X50mm, three terminal, PVC/polycarbonate body complete all as specified and directed.

S&F of door bell, multi magic, AC, 230 Volts single pole complete all as specified and directed.

S&F of bell push switch, single pole one way flush type, 5 Amps, 240 volts complete all as specified and directed.

S&F of angle lamp holder, PVC/polycarbonate type, ISI marked complete all as specified and directed.

S&F of stepped type (0-4/5 step) electronic fan regulator 120mm, 240 Volts, 100 Watts to 120 watts single pole, ISI marked including connecting, testing complete all as specified and directed.

S&F of decorative box type 20 -22watt LED fittings with and including LED T-8 tube light 20 watt of fire retardant engineering grade complete with all accessories internally pre-wired, connecting up with and including three core sheathed flexible copper conductor cable of required size and including mounted on PVC/Wooden round/square blocks-02 Nos complete all as specified and directed. (Make - Havells Cat No REGALBATTENT8UPTO1 x 22WDSBSWH/Crompton Greaves cat No : DMLN1LT8-16 for fittings and make - Crompton Greaves Cat No LTT8-20 for tubes /Havells Cat No PHOTONULTRAE2.01213T8SSTL20WLED865SPC as approved for LED lamp or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

S&F MCBs SP, 6 to 32A mps, 240 Volts, 50Hz, 'C' curve including necessary incoming and outgoing electric connection with suitable size of copper lugs all as specified and as directed by EIC.

S&F MCBs SPN 32 Amps, 240 Volts, 50Hz, 'C' curve including necessary incoming and outgoing electric connection with suitable size of copper lugs all as specified and as directed by EIC.

M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work complete all as specified and directed . (Note : (i)Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable color code of wire must be ensure for phase/netural/earth. (iv) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.

S&F of MCCB 3pole, 415 V fixed type of copacity 63 Amps, 16 KA, with connecting accessories complete all as specified and as directed.

S&F of vertical load line in sheet metal enclosures MCCB TPN DB's with double door for incorporating MCCB as incomer and MCBs SP/SPN as outgooing , IP-43 , TPN 4 way with 200 amps rated busbar, 440 volts, as per IS-8623 including taking out old UNSV DB and making good the disturbed surface of wall and match with the existing surface compelte all as specified and as directed. ( Note- MCCB 3 pole 63 amps as main incomer will be measured and paid separately)

S&F of powder coated sheet metal enclosure acrylic door 240 volts AC, SPN distribution board 8 way for flush mounting with 200amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 200Amps, MCB SPN/DP and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface & colour coat complete all as specified and directed. (Make: Legrand Cat No. 5076 21 8 way / L&T Cat No.DBSPN008GD or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

M&L for XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 35 sqmm, 3.5 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing complete all as specified and directed. (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required)

M&L for brick covering with width equal to length of brick as protection to cable with well burnt sub class ‘B’ bricks of size 250mm x 115mm x .75mm laid dry flat complete all as specified and directed.

M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep including required watering and consolidation after laying and stretching the cable complete all as specified and directed. (Note: Only punned down volume of sand to be measured)

M&L for 50mm bore GI pipe (Light Grade) laid under road or fixed with pole/wall of culvert as in protection of UG cable incl necessary MS clamp including taking down old unserviceable pipe complete all as specified and as directed.

M&L for 40mm bore GI pipe (Light Grade) laid under road or fixed with pole/wall for hanging of ceiling fan of 1200mm sweep including necessary MS clamp including taking down old unserviceable pipe complete all as specified and as directed.

Boaring holes horizontally under road without damaging the surface of road(minimum 1.0 Mtr bellow the road surface) with the help of GI tubing of dia not exceeding 100 mm dia for passing of UG cable all as specified and as directed.

Supply, fabricated and fixing of street light bracket made out of GI pipe 32mm dia medium grade bent to shape of 1.2 mtr long as directed including clamps made out of 40 mm x 6 mm flat iron for fixing bracket suitable for steel tubular poles including nuts and bolts, washers and other connected items of required size including painting with two coats of aluminium paint over a coat of red oxide primer including taking down old unserviceable bracket complete all as specified and directed.

S&F of 35/36 watt LED street light fittings IP-65/66 pressure die cast housing LED lamp aluminium compact high power LED street light with heat resistant toughened glass with LED lamp and necessary connection with suitable size copper cable including taking down old unserviceable street light fittings complete all as specified and directed . (Make : Crompton Greaves Cat No LSTS-36-CDL-M/ Bajaj Cat No BRTFG 36W LED/Philips Cat No. BRP052 LED 036 CW HP SLAF G SI PSU GR or equivalent model/Cat No of make as per Appx 'D' as mentioned in PS here-in-after)

Takind down existing electric meter carefuly from the meter box and refixed the same in the new location completed all as specified and directed.

Supply, fixing and commissioning water heater storage type, eletric operated, capacity 25 Litres, BEE 5 Star rated complete with all connected accessories suitable for AC supply, 240 volts, 50 Hz including connecting with water supply pipe line and all water and electrical connection complete with necessary PVC connection pipe all as specified and directed. (Make: Crompton Model No. Arno Neo 25-L5 Star, Bajaj Model No. Montage 25L 5 Star or equivalent model/make as Appx 'D' of PS)

S&F of heavy duty type exhaust fans AC single phase 230/240 V of size 300 mm sweep, 900 RPM with louver and necessary connection, testing including cutting the existing wall surfaces of brick/stone masonry and making the hole of any height for fixing the exhaust fan with nuts, bolts and washers after grouting in PCC including mild steel jalli and wooden frame for avoid insects after and including taking down of existing exhaust fan and deposit to MES store yard complete all as specified and directed. (Make : Havells model No Turbo Force SP 300mm-900RPM or equivalent model of Crompton Greaves as approved) (Note - Rate quoted includes necessary cutting chasing in brick/stone wall of 300mm dia suitable for fixing of exhaust fan and provision of heavy duty louvers at outside the building wall)

M&L for earthing with glavanised steel earth plate electrode of size 60cmX60cmX6mm thick buried directly in ground (earth pit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No.3 of SSR Part-I connected to earthing test point all specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC (1:3:6) type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe , 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 50mm thick made of RCC (1:1.5:3) type A-1 duly reinforced with 8mm dia TMT bar @150c/c both ways, one lifting handle made out of 10mm dia TMT bar 250 mm long embedded in cover slab and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer of 15 cm thick including taking down old unserviceable GI wire earthing complete all as specified and directed. (Note: Galvanised iron wire of 4mm dia upto 7.5m long including testing is deemed to be included with quoted rate).

DE CONSTRUCTION CO

B N ENTERPRISE