SPECIAL REPAIR TO BLDG NO P-94 AND PROVN OF GEYSERS AT MIL STN DHRANGADHRA

Amount

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for padestal/coping around poles, including necessary form work, finishing even and smooth without using extra cement, all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate in foundtion of pole/stay assembly etc including necessary form work, all as specified and directed.

M&L, precast cement concrete Block Masonary with solid blocks type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed .

M&L for RCC 1:1:5:3 type A-1 as in slabs supported on walls, beams and columns in floors, roofs, landings, fixed with tined tacks or galvanized wire staples complete all as specified and directed.

Rough finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

S&F, Flush shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames but with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, Aluminium handles, cast type, anodised 150 mm long complete all as specified and directed.

S&F, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nomonal dia of bar and 1.18 mm avrage width of aperture ,fixed with tined tacks or galvanised wire staples complete all as specified and as directed.

S&F M.S Framed work such as grills gratings etc with ends of bars sholdered and/or riveted into spikes ,framed guard bars /railings all as directed .

M&L for TMT 10mm dia bar and over, as in stiffeners, cut to length, bent to shape required, including cranking, bending, hooking ends, binding with and incluing mild steel wire(annealed) not less than steel wire 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-290, Gde E-165 all as specified and directed.

S&F rolled mild steel section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates except material complete all as specified and directed.

S&F, 1.25mm thick pressed steel frames size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges (125mm long - 06Nos.& 75mm long - 2 Nos for each door), lock strike plate, etc. including frames shall be filled with PCC 1:3:6, type c-0 (12.5mm graded stone aggregate) complete all as specified and directed.

S&F, in repair, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

S&F standard aluminium section powder coated any colour as approved for three track window/door frames/shutters sliding/ partitions etc including jointing cleat and rubber eading/linning, Pivot ,locking aragement and all hardware etc and fixed in position with stainless steel screws all as specified and as directed.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L in repair to Granite (of any type/colour) work (table rubbed and polished) 10 to 20mm thick in steps, jambs, pillars, window cills, cooking platform and like in CM (1:4) including pointing in white cement (1)2( using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:6 incl moulding, chamgering of edges complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C2, using 40mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C2, using 40mm graded stone aggregate as in sub base, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for coloured glazed ceramic joint free tiles of size 7 to 8 mm thick area exc 0.06 sqm but n.exc 0.18 sqm on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for rubber moulded exterior grade joint less coloured tiles, 10mm thick, area exc 0.06 sqm but n.exc 0.38 sqm with grey cement and pigments set & jointed and pointed in neat cement slurry over and including 15mm thick cement screed bed in cm 1:6 with grey cement and pigments in floors including taking down old tile complete all as specified and directed.

S&F 28mm dia fancy type Stasinless steel dropery rod fixed with stoper, brackets etc to wall complete as sample approved all as specified and directed by Engr - in - charge.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as sepcified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:6 finished the plaster surfaces fair and even complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar 1:4 on fair faces of concrete in ceilings, soffits, chajjas, fins facia etc. complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces (external surfaces) on wall in CM 1:4 finished the plaster surfaces fair and even complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement primer complete all as specified and directed.

Preparation of new plastered surfaces and applying two coat of oil bound distemper over and including a layer of wall care putty (average thickness 2 mm) complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

S&F, 4.8 mm thick plain sheet glass, ordinary quality and glazing not exceeding 0.8 Sqm in each pane fixed with glass putty complet all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old steel surface of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of reinforced cement concrete in any position not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling structural steel work including door , gatesbut excluding framed truss etc complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc) sheet in roof covering

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Taking down carefully copper/Aluminium point wiring (Light, fan, socket or power) complete including fitting such as switches, socket, bell pushes, ceiling roses, pendants/batten holder, call bell, regulators etc all as specified and directed by Engr-in-charge.

M&L for point wiring with and including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 1.5 sqmm. 1100 volt grade, single core including modular white cover plate with frame of suitable modules for mounting switches, sockets and fan regulators etc. over modular metal flush box concealed type and earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly complete all as specified and directed by Engr-in-charge for the followings :- Note : Wiring shall be done by using proper colour coding.

(a) One light/fan point controlled by one switch.

(b) 6 Amp socket outlet on independent board complete all as specified.

(c) 6 Amp socket outlet on same board complete all as specified.

M&L for point wiring for one 6/16 amp independent socket outlet controlled by one switch one way in and including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 2.5 sqmm 1100 volt grade, single core including modular white cover plate with frame of suitable modules over modular metal flush box concealed type for earth continuity insulated PVC unsheathed (green colour) 2.5 sqmm copper earth wire connected to common earth dolly complete all as specified and directed by Engr-in-charge. Note : Wiring shall be done by using proper colour coding.

S&F modular switch piano, flush type 6 Amps one way 230 volts complete all as specified.

S&F Socket outlet 3 pin 6 Amps flush type 230 volts complete all as specified.

S&F modular switch one way 16 Amps flush type 230 volts complete all as specified.

S&F modular socket outlet 2-3 pin 6 & 16 Amps flush type 230 volts complete all as specified.

S&F, modular fan step type regulator, suitable for 1200mm/1400mm sweep ceiling fan, 2 module complete all as specified and directed.

S&F Sheet metal enclosure double door for DB's SPN 8 way 240 V having 200 A rated bus bar complete all as specified and directed by Engr-Incharge.

S&F Ceiling rose 3 terminal size 50x65mm surface type 230 volts complete all as specified.

Labour only for cutting opening through brick walls for fixing of exhaust fan, including providing fixing and removing shoring cleaning and stacking bricks, removing surplus serviceable bricks, hard core etc. rubbish not exc 50m. forming jambs etc. to opening for 300mm exhaust fan including cutting tin wall for cement mortar 1:6 toothing and properly bonding into old work, also facing, jointing and pointing to match the existing work complete all as specified and directed.

S&F 30W New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 for bldg security light with GI pipe bracket of suitable size for fitting complete all as specified and directed by Engineer-in-charge. Make : Havells/Bajaj/Philips/Crompton.

S&F, LED flat panel of size 2' x 2' luminaire of 34 watt, environmental friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid Ceiling complete all as specified and directed as per Make of Havells cat No. PLUTONEO2X2PLR34WLED840S or equivalent make as approved by GE.

S&F, LED compact fitting/batten for single LED tube of 1x20W, 220 V AC decorative box type 4 ft with integral LED driver including 20W, T8 tube rod connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed as pe Make of havells cat No. LHFXCENNTN1W020 for batten and cat no. LHLDEFXD5L8R020 for holder or equivalent make as approved by GE.

S&F MCB SPN 32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

S&F MCB SP 6-32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

Taking down carefully old unserviceable main switches/ Distribution board any type including fuses MCB etc after removing all connection and making good the disturb surface all as directed by Engineer-in-charge.

Taking down ceiling fan of any sweep of any make by disconnecting electric connection from ceiling rose, carrying out necessary repair such as rewinding of motor, replacement of condensers of 2.5 MFD, rubber bushes, bearing, flexible twin core copper cable of suitable size including overhauling by carrying out repair such as applying grease to metal parts and replacement of suitable size of cotter/split pin as required including spray painting with white synthetic enameled paint after preparation of old surface of th ceiling fan and re-fixing in its original position, commissioning, testing complete all as directed by the Engineer-in-Charge. Note : Spares replace shall not be measured and paid seperately.

Supply and fix of exhaust fan, 300 mm sweep, 1400 rpm, MS body heavy duty, AC single phase, 230 volts with, blades, and frame and louvers including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed. Make : Crompton/Havells/Khaitan/Almonard/Bajaj

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated, 230Volts, single phase, 50 Hz AC, energy saving high density PUF insulation complete with all accessories such as safety valve, thermostate, NRV, inlet and outet (cold & hot) PVC pipes upto 450mm long, with 15A plug top, connection piece etc. including provn of suitable bolts, nuts, washers and grouting on walls and making good the disturbed surfaces to match with the existing complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth Lead 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth strip of 25x4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 20 mm dia light grade GI pipe & watering pipe shall be 15 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 15 mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 20 mm bore light grade 7.5m.

Shree Builders

Ramdev and Sons

Singh Engineer And Contractor