Construction of HP PWD Division building at Janjehali in Tehseil Thunag Distt Mandi H P SH Construction of building portion WS and SI Septic tank Soak pit Rain water harvesting system and Site development

Amount

Cutting in earth work all kinds of soils and disposal of excavated earth upto a lead of any metres such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to all floor level and removal of same for insitu reinforced concrete and plain concrete work as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . a) Foundation,footings and bases of columns etc. and mass concrete.

b) Columns, pillars, posts and struts in square, rectangular or polygonal in plan.

c) Flat surfaces such as soffits of suspended floors, roofs ,landings and the like, floor etc. upto any thickness.

d) Stair cases with slopping or steped soffits excluding landing.

e) Columns, pillars, Posts and struts Circular or curved in plan.

f) Beams, cantilevers, girders and lintels, sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels upto any depth in all heights from any floor level.

g) Vertical surfaces such as walls(any thickness) , partitions and the like including attached pillasters ,buttresses, plinth and string courses and the like.

h) Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete mechanically mixed and vibrated 1:5:10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) mechanically mixed and curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:5:10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) nominal size mechanically mixed and vibrated with 15% (fifteen percent) plum and curing complete excluding the cost of form work in retaining walls/breast walls. The size of plum shall usually be 150 mm to 300 mm (one hundred fifty millimetre to three hundred millimetre) as per HP.PWD specification and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing 100mm (one hundred millimetre) diameter poly Vinyl chloride pipe in Weep holes in brick masonry/stone masonry, plain/reinforced concrete abutments, wing walls return walls and retaining /breast walls etc. extending through the full width of the structure with slope of 1V:20H towards drainage face complete as per drawings and technical specifications as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Stone filling behind Retaining walls and Breast walls complete as per drawings and technical specifications including carriage of material within all leads and lifts and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying design mix M-20 (twenty) grade cement concrete work mechanically mixed and vibrated with minimum cement concrete of 320 kg (three hundred twenty kilogram) per cubic metre with graded crushed stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . i)Suspended floors , roofs, landings and shelves and their support , balconies, beams, girders,bressumers and cantilever upto floor any level.

ii)Walls (any thickness but not less than 0.10 m (Zero point one zero) metre thickness) including attached pilasters , buttersses,plinth and string courses etc. from top of foundation upto all floor level

Providing and laying cement concrete design mix M-25 grade of cement concrete work mechanically mixed and vibrated with minimum cement content of 320 kg/cum with graded/crushed stone aggregate 20mm. (Twenty millimetre ) nominal size) complete excluding cost of form work and reinforcement for reinforced concrete work upto all floor level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . a) Foundation, footings, bases of columns and the like and mass concrete.

c) Suspended floors , roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever upto floor any level.

b) Columns, pillars, posts and struts square rectangular polygonal in plain upto all floor level.

d) Stair cases (except spiral stair case) excluding landing but including preparing of the top surface and finishing of nosing upto all floor level.

e) Walls (any thickness but not less than 0.10 m (Zero point one zero metre) thickness) including attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto all floor level :

Providing and laying reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm nominal size) mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete upto floor all level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals .

Precast concrete block masonry (including quoin blocks, jamb blocks, closer etc) with solid concrete blocks of approved size made of cement Concrete, 1:3:6 (One Cement: Three Sand: Six graded stone aggregate.) 40 mm (Forty millimeter) nominal size and down gauge in cement mortar 1:6 (One Cement: Six Sand) in foundation and plinth upto floor all level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Precast concrete block masonry in partition walls 10 cm (ten centimetre) thick with solid block ofa pproved size (including quoin blocks, jamb blocks, closer etc with solid concrete blocks of approved size made of cement Concrete, 1:3:6 (One Cement: Three Sand: Six graded stone aggregate.) 40 mm (Forty millimeter) nominal size and down gauge in cement mortar 1:6 (One Cement: Six Sand) in foundation and plinth upto floor all level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 12mm thick Glass Reinforced concrete cladding of approved shape and texture of unistone or its equivalent made from portland cement alkally resistance glass fibres, UV resistant synthetic inoraganic pigment combined with the range of chemical additives on exterior surface side as on faces of Arch masonry walls etc. 12mm. thick cement plaster 1:3(1cement:3sand) and jointed with cement slurry including scaffolding etc complete in all respect as per specification and the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing 2nd class deodar wood work in frames of doors,windows,clerestory windows and other frames wrought,framed and fixed in position complete as per specification and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals and .

Providing and Fixing 12 mm (twelve millimetre) thick prelaminated Particle Board board both side prelaminated of approved shade and quality exterior/interior grade panalled shutters with frame of second class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm (forty millimetre) thick frame. including black enamelled M.S. butt hinges as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 40 mm (Forty millimetre) thick 2nd class deodar wood panelled glazed or panelled glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws etc. complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge.

Providing and fixing 19mm (nineteen millimetre) thick commercial board water proof shutters with 6mm (six millimetre) thick hard wood edging to be finished with PGI sheet lining fixing with nickle plated piano hinges with necessary screws etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing Stainless steel sliding door bolt of approved quality with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing Stainless steel tower bolts (barrel type )of approved quality with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . 200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

100x10mm (One hundred x ten millimeter)

Providing and fixing Stainless steel handles of approved quality with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (seventy five millimeter)

Providing and fixing bright finished brass 100mm.(One hundred millimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250mm (Two hundred fifty millimeter)

200mm(Two hundred millimeter)

Providing and fixing 115mm (one hundred fifteen millimeters) bright finished brass heaps and stepples (safety type) with necessary screws etc complete as per directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for aluminium door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of Engineer-In-Charge I/c carriage of materials with in all leads lifts and other incidentals.

Providing and fixing 19mm thick (ninteen milimetre) thick terramite resistant water proof commercial board box including shelves and shutters, the back side of cupboard/cabinet of 8mm(Eight milimetre) thick ply and cut portions of shelves shall be finished with 6mm six milimetres) hard board edging. The cut portion of shutters from all the sides shall be finished with 12 mm thick hard wood edging. the shutters from out side shall be finished with 1mm thick laminated of approved shade including piano hinges and magnetic catcher with all ascessories as per detail architectural drawing and specification complete in all respect as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Talai/Coble/Local stone flooring 50mm (fifty millimetre) (average) thickness of stone laid over 25mm (twenty five millimetre) thick cement mortar bed of 1:4(1cement: 4 sand) including pointing with cement mortar1:3 (1cement:3 sand) complete as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10mm thick full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm (ten millimetre) thick full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimetre) manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10 mm (ten millimetre) thick WI-Paraquit or action tesa clip in prelaminated wooden flooring (H.D.F) with poly sheet & thermocoal sheet with door profile and side moulding locks with all fittings ,etc. complete in all respect as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10mm thick antiskid full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10 mm (ten millimetre) thick full body glazed anti skid exterior grade vetrified tiles Asian/ Johnson/ Kajaria/ AGL or equivalant 600x600x15mm (six hundred into six hundred into fifteen millimetre) manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10 mm (ten millimetre) thick full body glazed anti skid exterior grade vetrified tiles Asian/ Johnson/ Kajaria/ AGL or equivalant 600x600x15mm (six hundred into six hundred into fifteen millimetre) manufactured of approved shade and colour in skirting risers of steps and dados laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing wall panelling of 12 mm(twelve millimetre) thick pre-laminated particlal board (one side) of approved brand over soft wood frame 40 x 40 mm (forty into forty millimetre) @ 600 x 600 mm (six hundred into six hundred millimetre) c/c having on both sides fixing with rawl plugs on wooden pegs on screws and snowing a 8 mm (eight millimetre) wide and 12 mm (twelve millimetre) deep grooves of required pattern in elevation and finished teak wood polished beeding out of 25 x 12 mm (twenty five into twelve millimetre) and cornice of size 75 x 60 mm (seventy five into sixty millimetre) of different pattren in top middle and corner joints including polishing and painting groove complete as per direction of Engineer in-Charge including carriage of materials with in all leads and other incidentals.

Providing and laying 10mm (ten millimetre) digital ceramic tile of size 300 x 600 mm (three hundred into six hundred millimetre) in skirting risers of steps and dados on 8mm (eight millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying granite stone in flooring 20 mm (twenty millimetre) (average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab flooring 25 mm (twenty five millimetre) thick kota stone on 20 mm (twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing completeas per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete within all leads, lifts and other incidentals and as per the directions of Engineer-in-Charge.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 60cm (Sixty centimetre overall 0.60mm (Zero point six zero milimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

Providing and fixing flushing 38cm (Thirty eight centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-In- charge.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filing the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals. PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm dia(One hundred milimetre) dia.

Providing and fixing M.S. BP Sheet 1.66 mm(One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge (Base members of steel work shall be paid & measured separtely) including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in position and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in: In Trusses and trussed purlins in buildings including carriage of materials with in all leads,lifts and other incidentals.

In Gratings framed guard bars laddeds railing brackets and similar works including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 62.5mm x 75mm (sixty two point five millimetre into seventy five millimetre) hand rails in 1st class Indian teak wood straight length complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing MS Railing for staircase having balluster of 20mm x 20mm (twenty millimetre into twenty millimetre) square Bars with a clear height of 85cm (eighty five centimetre) embeded in cement concrete steops and jointed with electrical/gas welsing at top along with MS flat of 40 x 6 mm (forty into six millimetre) the balluster welded/jointed with two number MS flat of 40 x 5 mm (forty into five millimetre) size complete with a priming coat of red lead paint as per drawing and specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing PVC Clamps of approved design with steel screws and rawl plugs etc complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm (twenty into ten into two milimetre) braced with flat iron diagonals 20x5mm (twenty ito five milimetre) size with top and bottom rails of T iron 40x40x6mm (forty into forty into six milimetre) with 38mm(thirty eight milimetre) dia steel pully complete with bolts and nuts locking arrangements, stoppers, handles, including applying a priming coat of red lead paint as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture of and of required shade of undecorated wall surface to give an even shade over and including a priming coat with alkali resistance primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing Wall painting with weather proof exterior grade emulsion of approved brand (Apexultima) or its equrlied on undecorated wall surfaces (two coat) to give an even shade and final finish after cleaning complete thoroughly the surface fto remove all dirt, dust and other foreign matter and sand papered smooth as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stoping ready mixed paint other than white as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals.

Polishing two coats with french polish on new wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals.

Making plinth protection with flag stone flooring 40 mm (forty millimetre) thick over a bed of 15cm (fifteen centimetre) with rammed earth and cement pointing 1 : 3 (1 Cement : 3 Sand) in proper shape including carriage of materials with in all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two centimetre) in cement mortor 1:6 (one cement: six sand) and in side blastering with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4 (one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Everest designer cement board ceiling tiles of size 600 x 600 mm (six hundred into six hundred millimetre) over readymade powder coated metal sheet section frame work 600 mm (six hundred millimetre) center to center grid suspended from ceiling of approved quality with butt jointing and nails as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying damp proof course 38 mm (thirty eight millimetre) thick with cement concrete 1:2:4 (one cement :two sand :four stone aggregate 12.5 mm (twelve point five millimetre) nominal size) and curing complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Applying a coat of hot bitumen (mexphalt 80/100 (eighty/hundred) or equivalent) using 1.70 Kg. (one point seven zero) per square meter on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Backfilling behind abutment, wing wall, R/walls and B/walls complete as per drawings and technical specifications including carriage of material within all leads and lifts and other incidentals as per directions of Engineer-in-Charge. as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying 40mm (fourty milimetre)Cement concrete flooring 1:2:4(one cement two sand four draded stone aggregate 20mm (twenty milimetre)nominal size laid in one layer finished floating coat of neat cement upto any floor level as per direction fEngineer-in-Charge carriage of materials with in all leads, and other incidentals.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 20mm (Twenty Millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing to wall and ceiling and floor Polythene Aluminium composite pressure pipe of 15mm dia of Kitec confirming to ISI 15450-2004 including making good the wall, ceiling and floor as per specification and the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying in trenches, galvanized mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. . 25 mm (Twenty Five Millimetre) nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm(Twenty Millimetre) to 40mm (Forty Millimetre) nominal size bore by providing and fixing tee including cutting and threading the pipes complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Construction chamber 300mm x 300mmx500mm (Three Hundred x Three Hundred x Five Hundred millimetre) inside size for stop cock with C.I. surface box 100mm x 100 mm x 75mm (One Hundred x One hundred x Seventy Five millimetre) (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement : two sand :four graded stone aggregate 20mm (Twenty millimetre) nominal size) 75mm (Seventy Five millimetre) thick foundation concrete 1:5:10 ( one cement : five sand : ten grades stone aggregate 40 mm (Forty millimetre) nominal size) and inside plastering with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement including curing complete with 100 mm (Hundred millimetre) thick walls of brick masonry in cement mortar 1:5 (one cement: five sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China wash down, water closet European type. W.C. pan No 2008 white shade with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) of Cera/Hindware/jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white plastic seat and cover for wash down water closet with C.P. Brass hinges and rubber buffers of Cera/Hindware/jaguar complete as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet Orissa Pattern No.2071 squatting pan (Indian type W.C pan) size 580mm x 440 mm (five hundred eighty millimetre into four hundred forty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) of Cera/Parryware/Hindware/Jaguar as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT White colour high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern No. 2602 of Cera/Parryware/Hindware/Jaguar with fittings with a pair of brackets with fittings such a lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) .as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of Cera/Hindware/jaguar with 1.5 mtr. ( one point five meters) Tube complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing of a pair of vitreous China 250mm x 130mmx30mm (two hundred fifty millimetre into one hundred thirty millimetre into thirty millimetre) foot rests for long pattern squatting pan water closet of Cera/Hindware/jaguar in cement mortar 1:3 (1 cement:3 sand), complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white glazed fireclay stall urinal with automatic flushing cistern of Cera/Hindware/jaguar with fittings R.S. or C.I. Brackets standard size C.P. brass flush pipe spreaders with unions and clamps (all in C.P. brass) C.I. Trap with outlet grating and other coupling in C.P. brass including painting of cistern and fittings, cutting and making good the walls and floors where required single stall urinal with 5 ltr. (five litre) automatic flushing cistern as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same 32mm (thirty two millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous china wash basin Cornet No 1008 of flatback size 550 x 400 mm (five hundred fifty into four hundred millimetre) of Cera/Hindware/jaguar with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China wash basin of Carnival No. 1009 of size 630mmx450mm (six hundred thirty millimetre into four hundred fifty millimetre) of Cera/Hindware/jaguar with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing stainless steel kitchen sink of size 460 x 560 x 229mm (four hundred sixty into five hundred sixty into two hundred twenty nine millimetre) No. 1022 of Paryag Polymers or its equivalent of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same (but excluding fitting) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32 mm (thirty two millimetre ) dia diametre C.P brass waste for wash basin or sink of approved brand and menufature as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing M.I. Union for wash basin or sink 32mm (thirty two millimetre ) dia size including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 32 mm (thirty two millimetre ) dia C.P. Bottle Trap for wash basin or sink as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 450 mm ( six hundred x four hundred fifty millimetre) beveled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. Brass Towel rail No 1581 of Jaguar complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 600mm x 20mm (six hundred x twenty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 120 mm (six hundred x one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing toilet paper holder No 1533 of Jaguar/ESS-Ess or its equivalent in C P Brass as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing soap trays (Vitreous China ) Recessed soap tray with hand rail 300 mm x 160 mm (three hundred millimetre into one hundred sixty millimetre) size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Division Plate for Urinals 600mm x 300.mm (six hundred x three hundred millimetre) Vitreous China as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass pillar tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass stop cock as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 15 mm dia PTMT concealed stop cock with flange of Jaguar and approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing P.V.C. connection with Brass unions 300/450 mm (three hundred/four hundred fifty millimetre) length15 mm(fifteen millimetre) nominal size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. Brass waste, and plug for glazed ware sinks, basins, etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and studs 32mm (thirty millimetre) nominal boreas per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing brass full way valve with wheel as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing brass ball valve (horizontal plunger type) High pressure with polythene plastic floats 15 mm (fifteen millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing G.I./M.I Union of following sizes (where not included in the items) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals 15 mm (fifteen millimetre)

20 mm (twenty millimetre)

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 1000 litres(one thousant litres) net capacity tank as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110*90 mm (one hundred ten x ninty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes confirming to ISI -15328 SN8 of Supreme/Fenolex/Kitech marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals 110 mm dia (one hundred ten) dia

150 mm dia(one hundred fifty) dia

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32 mm (thirty two millimetre) nominal bore PTMT waste coupling of approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT Urinal waste coupling of approved quality and colour 40 mm (forty millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT grating round of approved quality and colour 100 mm (one hundred millimetre) nominal dia as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT urinal spreader of approved quality and color as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Grab Bar of Jaguar WAC-WHT-BR0600 692 mm satinless 40mm (forty millimetre) dia steel pipe at 78 m (seventy eight metre) height with MS plate as the position of seat as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying (to level or slopes) and jointing reinforced concrete light duty non pressure pipes I.S. Class N.P.2 or P of the following internal diameter with collars and butt ends prepared for collar joint including testing of joints complete. 150 mm (one hundred millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Cement concrete 1:5:10 ( one Cement : five Sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size) in hunching of S.W. pipes of the following internal diameters, Including concrete for beddings, necessary form work and curing complete.150 mm (one hundred millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 (one cement :five sand)and water tight C. I. cover with frame of 300mmx300mm( three hundred xthree hundred) size (inside) the weight of cover to be not less than 4.53kg (four point fifty three kilogram) and frame to be not less than 2.72kg.(two point seven two kilogram) square mouth trap 150*100 mm ( one hundred fifty x one hundred milimetre)size P or R type as per the direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.

Constructing manhole with R.C.C. top slab in1:2:4 mix in ( one cement : two sand : four graded stone aggregate 20mm (twenty milimetre) nominal size) foundation concrete1:4:8 (one cement : four sand : eight )graded stone aggregate 40mm (forty milimetre)nominal size) inside plastering 15mm thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement : two sand : four graded stone aggregate 20mm nominal size) finished smooth complete including curring and testing Inside size 900 x 800 mm (nine hundred into eight hundred millimetre) deep including C.I. cover and frame (medium duty) 455 x 610 mm (five hundred millimetre) internal diameters total weight of cover and frame to be not less then 38 Kg (thirty eight kilogram) (weight of cover 23 Kg (twenty three kilogram) Weight of frame 15 Kg (fifteen kilogram) with 300 mm (three hundred millimetre) thick walls of square rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three Sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Rajiv Negi

MILAP SINGH THAKUR