Provn of iron gate chain link fencing sentry post with guard room flood lights with electric connection at A 1 def land and pillar No 79 near reflex shooting range and chain link security fencing around bldg No 8E of fd wksp coy EME at Chaubattia und

Amount

BOQ ( Sch A ) B/R Works Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc., and getting out in hard/ dense soil including trimming sides and forming bottom surface to the required level/slop etc for laying pipe line complete all as specified and directed.

Excavating over areas, n exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

Returning, fillingin, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil complete all as specified and directed.

Removing Excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M & L for design mix M-25 (using 20mm graded crushed stone aggregate) for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns etc; basement slabs, under-reamed piles and mass concrete complete all as specified & directed.

M & L for design mix M-25 (using 20mm graded crushed stone aggregate) for beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified & directed.

M & L for design mix M-25 (using 20mm graded crushed stone aggregate) for columns, pillars, piers, posts and struts complete all as specified & directed.

M & L for design mix M-25 (using 20mm graded crushed stone aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

M& L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete flat complete all as specified & directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams rough finished surfaces of concrete flat complete all as specified & directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete square or rectangular complete all as specified & directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) rough finished surfaces of concrete flat complete all as specified & directed.

S&F TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 6mm to 8mm dia and over as in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for damp proof course 40mm thick in cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork, polythene film 400 micron thick laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified & directed.

M & L for hard core of gauge not exc. 63mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L for Plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling, mass concrete complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement, laid in bays including necessary form work complete all as specified and directed.

M&L for 25 mm thick Cement concrete type-B-0 1:2:4 (12.5 mm graded stone aggregate) as subbase in floors complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, over with and including screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes complete all as specified & directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in skirtings, verticle surfaces, etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, over with and including backing coat of 10mm thick in cement mortar (1:4) complete all as specified & directed.

M & L for glazed ceramic coloured / printed tiles 300mm x 450mm, 6 to 7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles, over with and including backing coat of 10mm thick in cement mortar (1:4) for laying wall finishes complete all as specified & directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete al as specified and directed

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius as in half brick thick walls, built in CM (1:4) complete al as specified and directed

M&L for rendering 15 mm thick on other than fair faces of brick work or stone masonry or concrete surfaces in cement mortar 1:4 and finishing the surface even and smooth without using extra cement includig mixing of water proofing compound of approved make @3% by weight of cement complete al as specified and directed Note: Water proofing compound shall be measured and paid separately

Supply only integral water proofing compound complete all as specified & directed.

M & L for 15mm thick rendering in cement mortar 1:6, surface finished even & smooth on fair face of walls of brickwork or concrete surfaces complete all as specified & directed..

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished smooth and even in ceiling without using extra cement complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered wall surfaces and applying three coat of white wash complete all as specified and directed.

M&L for preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, frame rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F MS framed work such as grills, gratings,gates etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 Grade-E-165 complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & directed.

S & F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick 2nd class hardwood glazed and skeleton window shutters rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.20(b); supplied and fitted in chowkats , but divided into squares, with plain, chamfered or roun ded, mitred and rebated sash bars, any numbers complete complete all as specified and directed.

Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately.

S & F butt hinges, medium weight, cold rolled, mild steel and fixed, size of hinges 75mm complete all as specified and directed.

S & F butt hinges, medium weight, cold rolled, mild steel and fixed, size of hinges 100mm complete all as specified and directed.

Supply and fixing 100 mm mild steel pressed handles, oval type, stove enamelled black and fixed with wooden screws, complete as specified and directed.

Supply and fixing 150 mm mild steel pressed handles, oval type, stove enamelled black and fixed with wooden screws, complete as specified and directed.

S&F mild steel barrel tower bolts stove enameled black, with bright bolt length of bolt 100 mm (ISI marked) fixed complete fixed with screws,complete as specified and directed.

S&F mild steel barrel tower bolts stove enameled black, with bright bolt length of bolt 150 mm (ISI marked) fixed complete fixed with screws,complete as specified and directed.

Supply and fixing mild steel sliding door bolt plate type (ISI Marked) stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts, length of bolt 300 mm and fixed with mild steel wood screws all as specified and directed

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate 140 mm all as specified and directed.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

S & F 3 mm thick Sheet glass, figured , pin headed and glazing with beadings in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty/or wooden beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless steel wire staples complete all as specified and directed.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and directed.

Cutting chases, for water tubing or concealed , etc, and making good to facings where required and plastering in cement mortar (1:4) cutting not exceeding 10cm girth in brick walls complete all as specified and directed.

S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239 (Part -1) including all GI fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

S&F stop valves/angle valve, cast copper alloy, fancy type chromium plated with long shank & cup (concealed) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe complete all as specified and directed.

S & F vitreous china wash basin, white, flat back, size 630X450 mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand complete all as specified & directed.

S & F 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests with 'P; or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. in reapairs including Provn of lime concrete bedding and making good to floor complete all as specified & directed.

S & F 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, fixed on walls or floors, or as in weep holes complete all as specified and as directed

S&F vitreous china urinals, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; with grating and union for discharge pipe, all as specified and as directed

S&F 600mmx450mm bevelled edge looking mirror and fixed to wooden plug with CP brass screws and cup washers complete all as apecified & directed

M & L for 32mm bore high density polyethylene pipes (HDPE) complete all as specified and directed.

M&L for 75mm dia Cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S&F brass chromium plated tubular towel rail, 20 mm dia, D; type, 60 cm long between flanges complete all as specified and directed.

S&F chromium plated Soap disk fixed to plug with chormium plated brass screws all as specified and directed.

S&F Chromium plated shower rose 125 mm with or without swivel joints, including fixing to steel pipe or union complete all as specified & directed.

S&F 25 mm dia curtain rod/harrison rails,mild steel, chromium plated fancy type fixed with end brackets, stops ,rollers & all connected accessories complete all as specified and directed.

S & F PVC connections 15mm dia , 450mm long, , with PTMT nuts & washers at both ends complete all as specified & directed.

S & F Rotational moulded PVC water storage tanks 500 Ltrs capcity three layer (cylindrical vertical with closed top) hoissted and fixed in position complete all as specified & directed.

S and F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4 type-B-1 (using 20 mm graded stone aggregate) as in floors finished even and smooth without using extra cement complete all as specified and directed

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified & directed.

M&L for MS work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified & directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified & directed.

Supply only chain link MS galvanisd fencing, any size or type complete all as specified & directed.

S&F TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, as reinforcing bars in chain link fencing fixed complete all as specified & directed

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified & directed.

S&F Concertina coil 600 mm dia (in stretched position) hot dip galvanised steel wire coated with anticorrosive paint, making diamond shape with help of dove tail clips (18 SWG), fixed to the MS angle iron fencing post with & including binding wire complete all as specified & directed.

M & L for painting to new steel and iron surfaces of any description, not exc 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M&L Mild steel screw bolts (machine made) 11 to 15mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but not exc 10cm long complete all as specified & directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished smooth and even without using extra cement complete all as specified & directed.

Surface excavation in hard/dense soil n,exc 30cm deep and averaging 15cm deep and getting out complete all as specified and directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed.

M & L for 150 mm dia Salt Glazed stone ware drain pipes, Grade-A laid in trenches and jointed as specified complete all as specified and directed.

M&L for pre-cast RCC work 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, in shelves and cover slab on manholes including necessary form work complete all as specified & directed Note: Reinforcement shall be measured and paid separately

M&L for On site LLDPE conventional septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc for 10 users complete all as specified & directed.

M&L for soakage well of 1.2 m dia and 3 m effective depth, excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed brick masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/ DWC complete filled with brick bats complete all as specified & directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in surface channels and drains including necessary form work complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in block masonry with solid blocks exc 10 cm in width and set in CM 1:6 complete all as specified & directed.

M&L for raised pointing to block in course or ashlar masonry or concretre block walling in cement 1:4 complete all as specified & directed.

Forming embankments including earth spreading in layers n exc 30 cm thick watering, ramming/rolling and finishing to reqd size, shape etc, n exc 1.5 m high from base incl transportation complete all as specified and directed. (Note:- Qty of earth obtained from excavation, suitable for refilling will be used used under this item)

S&F GI water tubing of 20mm dia ,medium grade conforming to IS-1239 (Part -1) including all GI fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors or in trenches complete all as specified and directed.

S&F 20mm nominal bore gun metal, globe or gate valve, ISI marked, class-I, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

M&L for cutting existing steel tubing of size 100mm to 150mm bore for alteration or additions alongwith insertion of GI Tee of suitable size including connection, other materials required for same complete all as specified and directed

BOQ ( Sch A ) E/M Works S & F point wiring for one light point /one fan point / one bell point / one 5 Ampere socket outlet point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FRLS) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size copper conductor cable (FRLS) as in earth wire and connected to common earth dolly complete all as specified and directed,

All as per item No 104 above but One socket outlet 5 pin 5 Amp controlled by one, one way switch on same board.

All as per item No 104 above but wiring with using cable 2.50 sqmm size copper wire (FRLS) and earth wire of PVC insulated (Green colour) 2.50 Sqmm size copper wire (FRLS) for one 6 pin socket outlet, 16 Amperes on independent board.

Supply and fixing of switch piano flush button single pole one-way 5 Ampere complete all as specified and directed.

Supply and fixing of socket outlet 5 Ampere, 2 and 3 pins (TOTAL 05 PINS), flush type 250 volts AC complete all as specified and directed.

Supply and fixing of switch piano flush button single pole one-way 15 Ampere complete all as specified and directed.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC complete all as specified and directed.

S & F ceiling rose three phase, PVC / polycarbonate isolated body complete all as specified and directed.

S & F lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder includingLED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed. Note: The contractor shall submit five years of warranty of LED tube/bulb alongwith purchase voucher of materials

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with two core flexible copper conductor cable of suitable size complete all as specified and directed Note: The contractor shall submit five years of warranty of LED tube/bulb alongwith purchase voucher of materials

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Note: The contractor shall submit five years of warranty of LED tube/bulb alongwith purchase voucher of materials

S & F LED bulb 9 W complete all as specified and directed. Note: The contractor shall submit five years of warranty of LED tube/bulb alongwith purchase voucher of materials

S&F Exhaust fan metallic body ISI mark, 300 mm size with louvers including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 300 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed.

S & F MCB single pole, 240 volts, 5 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S & F sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 8 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall or niche including blanking plate complete all as specified and directed.

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 15 mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15 mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone by the contractor at his own expenses at no extra cost to Govt.

Supply, laying, jointing and commissioning LT XLPE 1100 volts 16 sqmm 2 core grade heavy duty under ground cable PVC insulated,strandred aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing laid in trenches, floor through pipes, in duct on pole and roads etc. complete all as specified and directed.

M&L for laying of fine river sand, free from sharp material for cable cushioning in trenches all as specified and directed. Note: The punned thickness of sand after consolidation shall be measurd and paid

M&L for brick protection covers laid over cables of sub class B bricks old size (230X115X75)mm all as specified and directed.

M&L for GI pipe 40mm bore light grade with all GI fittings as in protection pipe for cable complete all as specified and directed.

S&F sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 240 Volts 20 Amps complete all as specified and directed.

Supply & Fixing LED Flood light fitting 120 W 230 V AC outdoor type pressure die cast aluminium IP66 luminaire with high power LED as light source and electronic driver with impact and corrosion resisant including clamp and GI bracket light grade and provn of electric connection to fitting from Junction box by means of copper wire of 4 sqmm for phase neutral & earth complete all as specified and directed.

M & L for supply, transporting, erecting truly in vertical position and fixing of steel tubular pole swaged, over all length 9 metres, type 410 – SP – 31 complete with mild steel base plate, pole cap, finial taper plug, MS bolts, nuts & washers, necessary excavation & earthwork in hard / dense soil, PCC sub base block as mass concrete of size 600 X 600 X 150 mm in cement concrete 1:4:8 Type D-2 in base of foundation, PCC foundation block of size 600 X 600 X 1500 mm in cement concrete 1:3:6 Type C-2, pole plinth of size 600 X 600 X 300 mm in cement concrete 1:2:4 Type B-1 including necessary form work as required at site and painting of pole with two coats of anti corrosive black bituminous paint through out internally and externally upto planting depth (embedded in concrete) and remaining portion of the pole painted two coats of aluminium paint over a coat of red oxide primer on complete exposed surface including painting of 05 Nos. bands / strips of 30 cm wide each with two coats of synthetic enamel paint (black & yellow) at a distance of 30 cm from plinth block upto 1500 mm height and marking / sign writing of pole number and feeders locations of pole with thick synthetic enamel paint (white) complete all as specified and directed.

Supply, laying, jointing and commissioning LT XLPE 1100 volts 25 sqmm 4 core grade heavy duty under ground cable PVC insulated,strandred aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing laid in trenches, floor through pipes, in duct on pole and roads etc. complete all as specified and directed.

Supply, laying, jointing and commissioning LT XLPE 1100 volts 16 sqmm 2 core grade heavy duty under ground cable PVC insulated,strandred aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing laid in trenches, floor through pipes, in duct on pole and roads etc. complete all as specified and directed.

Supply, laying, jointing and commissioning LT XLPE 1100 volts 10 sqmm 2 core grade heavy duty under ground cable PVC insulated,strandred aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing laid in trenches, floor through pipes, in duct on pole and roads etc. complete all as specified and directed.

M&L for GI pipe 25mm bore light grade with all GI fittings as in protection pipe for cable complete all as specified and directed.

Supply and fixing Junction Box made up of High quality thermoplastic polycarbonate enclosure with IP 65 degree of protection, weather proof, corrosion proof, dust proof, insulted and shock proof, fire retardant non toxic material with internally embedded gasket with 10 Amp MCB and 4 nos busbar terminal of size 200x160x98 mm of make hensel or equivalent make of Sintex/ Universal complete all as specified and directed

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised strip 32x6mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone by the contractor at his own expenses at no extra cost to Govt.

Supply, fabricating and fixing of sheet metal encluser made of 16 gauge MS sheet outdoor type of suitable size including fixing of MCCB of cap 200 Amp, 415 Volt,50Hz, 4 pole, 36 KA, AC supply with 300 Amp rated busbar on porcelain insulators for neutral link double door type with locking arrangement complete with MS angle iron frame of size 25 x 25 x 5mm with nut/bolts and PCC plateform work including painting with two coat of synthetic enameelled paint over one coat of red oxide/ primer complete all as specified and directed.

aditya construction

KUMAON VALLEY CONSTRUCTION