8203 LOWERING/LIFTING AND REPAIR/MAINT OF SUBMERSIBLE PUMP MOTOR AND CENTRIFUGAL PUMPING SET, DOSING PLANT, CLEANING OF OVERHEAD TANK AND ALLIED WORK OF WATER SUPPLY AT UNDER GE (E) BAREILLY.

Amount

Lifting/taking out defective submersible pump of any capacity alongwith column pipe of any size and submersible cable, dismantling the pump from motor, setting aside for repair /servicing / overhauling including lowering the pump set into borewell replacement of packing and nut bolts (if required) and testing after the completion of repair works in the presence of JE/ Engr in charge .

M&L for rewinding to submersible pump 50 HP of any make with super enameled copper winding wire PVC coated 2 mm thick as per taken out qty, Providing PVC separators, PVC sleeves & jointing compound complete all as specified and directed. Note:- Rewinding, replacement items will be measured and paid seprately under relevent item.If the same motor copper winding wiring burnt second time in the above CA Period, The contractor is responsible to paid and rewind the same at their own cost.

All as per item no 02 above but capacity 41 Hp

All as per item no 02 above but capacity 10/15Hp

Repair/Replacement of following parts of the submersible pump and motor for capacity 40/41/50 HP of original company as approved by Accepting officer. Make : KSB, Crompton,Kirlosker

Thrust bearing plate made out of carbon for submersible motor

Gun metal bush for submersible motor

Shaft sleeve made out of stainless steel for submersible motor

Clamp stud for submersible motor

Rotor balancing of submersible motor

Shaft grinding of submersible motor

GM Neck Ring for submersible pump

Stainless steel sleeve for submersible pump

Stainless steel pump shaft for submersible pump

Stainless steel impeller for submersible pump

Cast iron bowl for submersible pump

Rubber bush for submersible pump

M&L for Painting to pipe of pump house rising mains hydrants, sluice valves, pipe, fittings, NRV, discharge head etc after cleaning, scrapping and making the surfaces free from rust of main externally and painting with two coats synthetic enamelled paint in black / blue / red including marking / writing on pipe etc complete as specified and directed

S&F in repair electric shock treatment chart coloured of size approximetely 90 x 60 x 6 mm thick plywood with teak wood frame including covered with plastic laminated sheet complete all as specified and directed.

S&F in repair machinary maintenance chart coloured of size approximately 3 ft x 2 ft & 6 mm thick plywood with teak wood frame including covered with plastic laminated sheet complete all as specified and directed.

M&L for trimming vegetation or small inequalities clearing all grass vegetation, saplings, shrubs, brushwood, roots, and tree of surroundings area up to 500 sq mtr including cleaning and removing rubbish upto a distance of 50 mtr outside the periphery of the area under clearance of water supply installations complete all as specified and as directed.Note-trimming will be done two times during contrct period at all installations of water supply. etc complete as specified and directed

S&F in repair for Aviation light on OH tank 18/21 mtrs staging (on top of OH tank) with all fittings, fixtures and accessories including 2.5 sqmm wire Three core in 20 mm PVC conduit from light to connection points including 2-way MCB DB with isolator (10 Amp) capacity complete all as specified and directed.

Supplying, Laying, jointing and testing 2.5 Sq mm 2 core, PVC insulated, armoured, heavy duty, Copper conductor cable 1100 volts grade, laid in trenches / ducts, floors, fixed to pole / walls etc. complete all as specified and directed.

S&F in repair for glow sign board (box type) LED of required size 600 x 600 mm made out of MS sheet of suitable size with sheet fixed on front and quality marked with details of Pump House etc on front and rear with different colours including provision of LED power- fittings & fixtures in equal distance to illuminate board including connections with 2.5 sqmm single core stranded copper conductor cable and writing with 10 mm size letters as specified and directed .

Supply & fix in repair 1100 volts grade heavy duty cable PVC insulated aluminum conductor screenedserved with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm GI suspension wire, one twin core cables flat or circular of size 10 Sqmm etc complete all as specified and directed.

S&F in repair Off load change over switch 200 Amp, 4 pole, 415 Volt, etc complete all as specified and directed

Supply and fix in repair energy saving and environemntal friendly long life versatile pressure die-cast aluminium IP-65 roadway luminaire 72 W LED fitting with high power LEDs light source and electronic driver etc complete as specified and directed

S& F in replacement new generation post top energy saving environment friendly, long aesthetically designed with symmetrical light distribution spun aluminium landscape luminaire with power LED,s of 35 Watt as light source of 35 Watt suitable for pole dia 76 mm of complete all as specified and directed

S & F in replacement of street light brackets 40 mm bore GI pipe medicum grade upto 1.5 mtr long bend to shape including flat iron clamps and sutable nuts and bolts .etc complete all as specified and directed

Material and labour for replacement of PVC insulated single core multistranded copper cable of size 1.5 sq mm unsheathed 1100 volts grade drawn through conduit / cassing capping on surface / pole / wall concealed and making good of disturbed surface including taking down unserviceable wire etc complete all as specified and directed

S&F Bldg Security light energy efficient 1X20 Watt LED 6K Endura cityliner leaf (with Toughned glass) die cast aluminium and fixing arrangement of fitting including 1 mtr 35/50mm GI 90 degree bend pipe complete all as specified.

M&L for Earthing complete with using GI earth plate electrode 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using 4 mm dia GI Wire as earth lead moulded and retreived to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plate upto external face of the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mess fixed on water pipe and provison of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handle with and including necessarry excavation and earth work including laying the pipe concealed in floor / wall allas per plate NO-3 of SSR Part-I complete all as specified and directed and testing on completiopn (Note:- If the desired resistance is not found earthing shall be done by the contractor at no extra cost to Govt).

Taking down the Unseviceable LT panel installed at PH and replacement with new one CPRI approved with following parts including panel board Wall mounted LT panel board indoor type of size 1200 x 1200 x400 mm with sheet CRCA sheet of 2 mm thickness comprising of the following :- ( a) 3 pole power contactor type ML 4 suitable for operation on,440 Volts, AC, 50 Hz -03 Nos (b) over load protection relay with relay range 45-75A suitable for operation on 3 phase, 415 V -01 Nos (c) voltmeter three phase anologue type class 1 voltage range 0-500 V flush mounting 96x96mm (d) ammeter three phase anologue type 5A class 1 of range 0-200 A flush mounting 96x96mm inculding CT 200/5 (e) MCCB 125 A capacity 3 pole for 415V -01 Nos (f) Supply and fix in repair MCCB 200 A capacity 4 pole for 415V -01Nos (g) indicating lamp on all 3 phases R Y B -01 set (h) PVC insulated multistranded copper conductor single core cable 4 sq mm (Nominal cross sectional area) as per site requirement including suitable size of copper lugs etc all as specified and directed-01 Job (j) single phase preventer direct mounting type with relay range 28-40 A 230 Volts suitable for electric motor of water supply installation-01 No (k) Electronic timer type ST 100 suitable for operation on 240/360/415 volts 50 Hz for 3-10 Sec-01 Nos. (l) Painting complete panel board with one coat of silver inside and outside -01 Job

Supply & replacement of Contactor ML-3 ,suitable to operate 35-45 HP submersible pumping set Cat part No SS-90721 Make-L&T or equivalent to approved make as specified in CA.

Supply & replacement of Contactor ML-4 ,suitable to operate 50-60 HP submersible pumping set Cat part No SS-90910 Make-L&T or equivalent to approved make as specified in CA.

M&L for cleaning of RCC Over Head Tanks capacity 1 lakh gallon and removing and taking out sand, sludge and mud etc including disposal of the same at a distance not exceeding 100 mtrs from the tank,including two coats of whitewash on whole internal walls of OH Tank all as directed. NOTE:-All the safety equipments for workers working on OHT and U/G Sumps will be provided by the contactor.Cleaning of OH tank is in every 6 month or contracor is responsible to clean all OH tank two time in their contract at same cost quoted rate.

All as per Srl item No 24 here in before but capacity 50000 gallon.

All as per Srl item No 24 here in before but capacity 25000/35000 gallon.

Supply only Calcium based granularhypo chlorite 65% to 70% disinfectant for water treatment, Packing in 45 Kg, plastic drums complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 125 to 160 amp with breaking capacity 36 Ka complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 160 to 200 amp with breaking capacity 35 kA complete all as specified and directed.

Repair and servicing of powder base vacuum type chloronome / dosing plant for smooth functioning including necessary spares as required for rectifying the defects for smooth functioning for the following plants :- Location :- Pump house No. 12, 25, 27, 28, 29, 30, 31, 32, 33, 34, 36, 37, 38, MH and swimming pool etc. Note:-(i) The cost of complete spares, rewinding & repair of mixing motor is deemed to be included in the quoted rate. (ii) All testing equipments to be avaliable in installations. (iii) Contractor shall be provied all equipment with proper protection from chlorine gas and mask to all their employee.

Taking out connection of Chlorine / Altoch dosing system , detecting fault and repair /replacement of unserviceable parts and refixing same after completion job and connecting dosing system and testing complete all as specified and directed. (NOTE: Spares parts shall be measured and paid separately as Supply only)

Supply only rotor assembly with bearing brackets and tolerance rings suitable for decree dosing pump complete all as specified and directed.

Supply only pump tube suitable for dosing pump complete all as specified and directed.

Supply only injectior assembly suitable for dosing pump complete all as specified and directed.

Supply only duckwill suitable for dosing pump complete all as specified

Supply only diaphragm assembly suitable for dosing pump complete all as specified

Supply only weighted suction line stainer suitable for dosing pump complete all as specified and directed.

Supply only Agitator Motor electric driven 230 Volt 50 Hz,single phase,120 W & 900 RPM copper wounded complete all as specified and directed.

Supply only PVC pipe as per existing size all as specified

S&F in repairs electronic timer type ST 100 suitable for operation on 415 volts 50 Hz for 3-30 Sec all as specified and as directed.

S&F in repairs electronic Single phase preventer operation on 415 volts 50 Hz all as specified and as directed.

Supply only grass and weeds killer chemical of make Roundup all as specified and directed.

S&F rubber mat of size 1.0mx2.0mx12 mm at installation of etc complete as specified and directed

S&F pressure gauge of dial 30 to 60 suitable for fixing at 100/150 header mm pipe with all fiting andf fixtures etc complete as specified and directed

S&F mini motor protection relay for 35-51hp submersibble motores of make L&T all as specified amd directed.

Supply and fix in repair spare conntact kit for ML 3 contractor complete all as specified and directed .

Supply and fix in repair spare conntact kit for ML 4 contractor complete all as specified and directed .

S&F in replacement of PVC bib tap 15 mm.bore etc complete as specified and directed

M&L for dismantling of motor, 3 phase, 7.5 KW, taking out burnt winding wire from stator, cleaning all slots properly, repair of pump/rewinding the motor with proper guage of super enamelled winding wire and varnishing properly including baking and providing insulation and packing properly re-assembling the motor with pump and installed at its proper position and testing the same including connection plate etc complete as specified and directed.

S&F in replacement MS ERW column pipe screwed 150 mm nominal bore having wall thickness not less than 7.11 mm electric resistance welded with MS flanged 16 mm thick heavy duty confirming to IS 6392 incl 2 mm thick rubber sheet and steel nuts and bolts 10 mm long with washer. etc complete as specified and directed

M&L for dismantling of non clog type centrifugal pump set of capacity 12.5hp either fixed or floor or on trolley mounred and taling out unsv spares and performin following operation to complete the task-: Rewinding of the motor centrifugal pumping set with insulated copper winding including sleeves as per original approved and replacement of worn out parts including griding of parts testing & transport charges complete all as specified and directed. replacement of motor bearing with lock nut -02 Nos Repalcement of fan motor-01 No Replacement of star coupling set with rubber-01 Each

Take the water sample from the bore well at ph no. 12, 25, 27, 28, 29, 30, 31, 32, 33, 34, 36, 37, 38, 41, 26, 20, 21, 22, 37 MH PH and two consumer end and send it for physical / Chemical / Bateriological test from any recognised govt agency (two times in contract period) and provide its report to Engr in charge.

S& F in replacement submersible pump / motor electric driven 415 Volts, TP suitable for 200/250 mm bore well casing pipe size 200/250 mm supply complete of 41 HP all as specified and directed. Make:-CRI / KS / Havells

S& F in replacement submersible pump / motor electric driven 230 Volts , SP suitable for 25 mm bore well casing pipe size 50 mm supply with staster complete of 01 HP all as specified and directed.Make:- CRI,KS and Havells

S& F in replacement Pressure Booster Pump / motor electric driven 230 Volts, SP suitable for 20/25 mm bore with staster complete of 01 HP all as specified and directed. Make CRI,KS,Kirloskar and Havells

S& F in replacement Open submersible pump / motor electric driven 230 Volts, SP suitable for 25 mm bore well and Supply with staster complete of 01 HP all as specified and directed. Make CRI,KS,and Havells

S& F in replacement HI Flow 1 HP Centrifugal pump / motor electric driven 230 Volts, SP suitable for 20/25 mm bore with staster complete all as specified and directed.Make CRI,Kirloskar and Havells

Supply fixing testing and commissioning submersible cable flat 16 sqmm 3 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed.

Supply fixing testing and commissioning submersible cable flat 1.5 sqmm 2 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed.

Supply install in repair and commissioning of Granular chlorination dosing pump of high pressure single head gear motored adjustable dosing pump having output of 2 U.S. GPD to 40 U S GPD and adjustable high pressure of up to 100 PSI (7 kg/cm2) or more , power input 230 V, 50 HZ self priming with nonmetalic with connecting nuts, ferrules and with all accessories including lead, tubing connection injection check valve complete all as specified and directed. Preparation tank (300 ltr) : (i) Water inlet line (ii) Outlet with strainer (iii) Drain (iv) Overflow (v) Conical bottom for sludge deposition (vi) Pot hole with over (vii) Level gauge (viii) Inspection port (ix) Agitator 120 watt 900 RPM single phase mounted with plastic shaft and impeller. Service Tank (100 ltr): (i) Water line inlet (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level gauge (vi) Inspection port make-Potter & watts/Briozing/Declibec. Note :- Tenderer may note that amount of credit will be deducted from the total amount arrived, at the time of Acceptance of contract

Supply install in repair and commissioning of Granular chlorination dosing pump of high pressure single head gear motored adjustable dosing pump having output of 2 U.S. GPD to 40 U S GPD and adjustable high pressure of up to 100 PSI (7 kg/cm2)or more ,power input 230 V,50 HZ self priming with nonmetalic with connecting nuts ,ferrules and with all accessories including lead,tubing connection injection check valve complete all as specified and directed. Note :- Tenderer may note that amount of credit will be deducted from the total amount arrived, at the time of Acceptance of contract Make :- Declibac,Poter & watts and equlavent make all as specifed and directed.

Disconnecting, taking out and removing old existing unserviceable underground, LT cable of any description and in any position complete including taking down protection pipe,PCC Cover/Bricks etc all as specified and directed for the following sizes:

(a) 70 Sqmm any core

(b) 95 Sqmm to 120sqmm any core

Supply, laying, jointing and testing XLPE cable, PVC insulated, armoured, heavy duty, aluminum conductor cable 1100 volts grade of any description and any make laid in trenches/ducts, floors, fixed to walls etc. complete all as specified and directed for the following sizes :-

(c) 70 Sqmm 3.5 core

(d) 95 Sqmm 3.5 core

(e) 120 Sqmm 3.5 core

Excavation in trenches in soft & loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope / gradient for laying cables/ pipes etc. all as specified and directed including removing cable protection PCC covers/ bricks & stacking serviceable covers / bricks for reuse and disposal of unserviceable covers within 50 m all as specified and directed. Note : Excavation shall be made carefully in order to avoid damage of existing cables and protection covers.

Returning, filling in including spreading, leveling, watering and well ramming in layers of 25 cm thick after the cables etc. are laid, jointed & tested complete all as specified and directed

Removal of surplus excavated soil exc. 50 mtr but n. exc. 250 mtr distance and depositing where directed at a level not exceeding 1.5 M above the starting point etc complete all as directed.

Supply and laying new dry river sand laid in trenches 8.0cm below the cable and 15cm above the cable and gently punned to 18.0cm as cable cushioning and covering complete all as specified and directed. (Note:- Only punned 18 CM thick sand cushioning shall be measured and paid)

Supplying & Laying Sub Class `B’ bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection all as specified and directed.

Supply install in repairs and commissioning of Multi-Cavity water sanitiser / conditioning stationproportinal dosing arrangement at zero discharge of the power ree automatic system, 100 Ltr. Tank, Cavities are compieted with Lids. Attachement -Centrifugal pump with following specifications:- Power-1 HP,0.75 KW,pipe size (suction ), 1" Delivery pipe 1", Total Head up to 6 bars, Discharge- up to 3700 LPM, Over flow valve, water inlet valve, outlet valve (for O line automatedgravity flow) drain valve. Model-STEQUA ADS PRO System. Make- Declibac technologies or equivalent as specified and directed. with all assessary completed.All as specified and directed.

Supply only Chlorine tablets contained in plastic cylindrical -sealed disposable sanitizer refill for disinfeetion of drinking water with arrangement for controlled relese of disinfectant in water suitable for operationthrough for recommended dosing system. (a) Relacecement indication visual & weight variation water contact orifice design : Sealed when dry, exposed upon immersion oxperation type, Non contct, non inhalatory complete all as specified and directed. Note :- Each Set of 25 refill.

S& F in replacement Agitator motor electric driven 230 Volts, SP suitable for Dosing system mixing of clorine all specified and directed

S& F in replacement Openwell submersible pump/ motor set Horizontal / Vertical electric driven 415 Volts , TP,Head 68 to 100 meter hight, suitable for 80/100 mm bore supply complete of 10 to 12.5 HP all as specified and directed. Make :- CRI , KS, Kirlosker

K.S.Traders