Department of Tourism-Kitchen Work at Ramanilayam Guest House, Thrissur District

Amount

Civil Works

2.1.1 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

15.9.2 Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

15.7.4 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.12.1 Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

15.23.1 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

15.2.2 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 or leaner mix ( including equivalent design mix)

15.3 Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.5 Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work ( Payment shall be made on the cross sectional area of R.C.C. or R.B work) as per direction of Engineer-in-charge.

15.6 Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B work.

15.60 Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

15.18 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

OD86121/2025-2026 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (as per specification 14.46)

OD86123/2025-2026 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (as per specification 14.43)

15.28.2 Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos cement Sheet

2.28.1 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

4.3.1 Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All work upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum

5.33.2.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All work above plinth level upto floor V levelConcrete of M25 grade with minimum cement content of 330 kg /cum

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1 Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.35 Add for using extra cement in the items of design mix over and above the specified cement content therein

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.25.1 Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources)

OD94103/2025-2026 Applying a coat of Inertol Poxitar Coal tar epoxy coating per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

OD86758/2025-2026 Applying Antitermite treatment on flooring using second generation chemicals (Anti Termite PREMISE 350 SC IMIDACLOPRID) which is ecofriendly and nil harmful for human beings and pet animals which control the pests including all cost and labour charges etc. complete

60.7.1 DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.1.1 Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

50.6.3.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.13.1 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

5.30 Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

21.1.1.3 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPolyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron )

21.1.2.3 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micorn)

9.147D.3 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

9.147D.5 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

9.151 Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete.

21.13 Providing and fixing Brass100 mm mortice latch and lock with 6 levers without pair of handles ( best make of approved quality ) for aluminum doors including necessary cutting and making good etc. complete

OD94274/2025-2026 Providing and fixing rolling wheels for sliding windows, with necessary screws etc.As per directions of Engineer - in- Charge

21.8.1 Filling the gap in between aluminium frame & adjacent RCC/ Brick / Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawing and direction of Engineer-in -Charge complete.Upto 5 mm depth and 5 mm width

9.48.1 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

50.9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) using good quality Pincoda wood

50.9.2.2 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required sized with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer in-charge using Pincoda wood

50.9.4.2 Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Pincoda wood

OD94306/2025-2026 Preparation of wood surface for melamine polish: Preparation of wood surface for polishing as per the follwoing procedure: Filling the holes and screw marks in the wood surface using Wudd filler and sandering the surface using 80 grade paper. Applying First coat Sanding Sealer. Fillig the Joints using Filler Powder and sandering with 120 grade paper.Applying second coat Sanding Sealer and sandering with 220 grade paper. Applying One coat melamine sealer and sandering with 320 grade paper

OD86459/2025-2026 Melamine polishing on wood work ( one or more coat), as per specification.14.70

9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.74.3 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:150x10 mm

9.74.4 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:100x10 mm

9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

11.26.1 Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick

11.27 Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.46.2 Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.48.2 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

OD94353/2025-2026 Providing PVC Tile beading in the edges and corners of tile work including cost conveyance labour charges etc complete.

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete

8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

10.5.1 Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces

10.31 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer In charge.

9.62.1 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (Copper oxidized as per IS 1378).300x16 mm

9.63.1 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : (Copper oxidized as per IS : 1378)250x10 mm

OD86790/2025-2026 Supplying Stainless steel Padlock and Keys

9.119 Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door fame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer-in Charge.

9.120.1 Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of whicj 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95 mm wide PVC sheet out of which75 mm shall be tapered in 45 degree on th inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mmx2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded /sealed to the styles & rails with 7 mm (5 mm + 2 mm ) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer -in-charge, manufacture's specification & drawing.30 mm thick plain PVC door shutters

OD87025/2025-2026 Providing and fixing cylindrical door lock of approved quality with necessary stainless steel screws etc.

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

12.48 Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

Fabrication Works

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm)

OD78344/2025-2026 Providing and fixing 150 mm wide square cut PVC 4kgf/cm2 rain water gutter pipe with iron brackets with 25x5 mm size flat,screws and washers etc.,including making necessary connections with rain water pipes etc.complete.

50.18.9.18.2 Providing and fixing PVC pipes including fixing the pipe with clamps/Clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 4 Kfg/cm2 External work - Exposed on wall

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

Electrification Works

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.55.2 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.55.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required

1.17.3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.17.30 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 6 sq. mm

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

90.10.3.33 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A 3pin Shuttered socket

OD83799/2025-2026 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required. 20A DP switch- as per quotation

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

90.10.1.2 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )2 module moulded plastic box on surface

1.28.1 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

90.10.1.3 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )3 module moulded plastic box on surface

1.28.2 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

2.3.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

2.4.2 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 Way (4+18), Double door

2.10.1 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.10.3 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

OD91209/2025-2026 Supplying and fixing 40A to 63A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Four Pole

2.14.1 Supplying and fixing following rating, double pole, (single phase and neutral),240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

2.15.1 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

OD91468/2025-2026 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

OD91481/2025-2026 Supply, installation, testing and commissioning of thermoplastic enclosure in accordance with IEC60529,environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid & anti corrosive enclosure having size not less than 126x228x111mm as required. 1 row 4 module

OD91498/2025-2026 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 25x3mm Cu strip

OD91499/2025-2026 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. 3.15 mm copper conductor ( 10 SWG)

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

OD91505/2025-2026 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. 25 x3 x400 mm Cu earth bench

OD91674/2025-2026 Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 70 sqmm XLPE Al

OD91675/2025-2026 Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 4C 25 sqmm XLPE Al

OD91676/2025-2026 Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required.

OD91812/2025-2026 Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1KV grade of following sizes as required. 4C 6 sqmm XLPE Cu

7.7.1 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq.mm (clamped with 25x3mm MS flat clamp)

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.34 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

OD91980/2025-2026 Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 4C 6 sqmm XLPE Cu

1.41 Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

1.50.1 Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

90.4.8 Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

OD92020/2025-2026 Supply of 20 +- 2W LED tube light fitting housing made of Extruded thermal polycarbonate with 6500K colour temperature with duly wired up for use on 230 V AC. The fittings shall be directly on ceiling/ wall, etc. as required. Make Wipro or equivalent

OD94418/2025-2026 Supply of 34 ± 2W LED tube light fixture housing made of polycarbonate, with 6500K colour temperature, with a lumen output of 100lumen/Watt, CR1>80, ripple <5%, THD<10%, power factor >0.95, 50000 burning hours etc. as required. Make - Philips Endura or equivalent.

1.58 Supplying and fixing PVC batten/ angle holder including connection etc. as required.

OD92012/2025-2026 Supply and fixing of 9W LED Bulb on existing holder as required

OD92023/2025-2026 Supply of 7+- 2W LED bulkhead fitting (IP 65), housing made of die cast aluminium with 6500K colour temperature with a lumen output minimum 100lumen/Watt, CRI>80, power factor 0.95, THD< 10%, 50000 burning hours, suitable for outdoor applications etc. as required. Make -Philips, Vistaglow or equivalent

OD92148/2025-2026 Supply of following Exhaust fan in plastic frame working on 230 V AC etc. as required. 250mm light duty exhaust fan. Make - Crompton or equivalent

OD94442/2025-2026 Supply, installation, testing &amp; commissioning of Sub panel - Kitchen, cubicle type, made out of 1.6mm thick CRCA sheet, totally enclosed, free standing, wall/floor mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable on both sides, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene gasket etc. The panel shall include supply &amp; installation of following switchgears, metering instruments and accessories as per specification. Meters and indication lamps : RYB indication with control fuses -1 set, MFM showing V,A,F, etc. with control fuses and CT-1 set, Incomer: 100A FP MCCB 16kA - 1no. Busbar: Al busbars suitable for 100A. Outgoings: 40A TPN MCCB 16kA-1 no, 40A TP MCB 10kA C curve-4 nos, 25A TP MCB 10kA C curve-4 nos, 25A SP MCB 10kA C curve-1 no. Accessories as per schematic drawing

Mechanical Works

OD31582/2023-2024 Exhaust Fans &quot;Supply, Installation, Testing and Commissioning of Centrifugal Direct driven/belt driven fan with VFD and by pass starter. The fan wheel shall be of the non overloading backward inclined and constructed of aluminium. The motor shall be of Class F insulation. The fan should be precoated, suitable for outdoor use. Makes: Nicotra/Greenheck/Systemair/Kruger&quot; 10000 CFM 50mm ESP

OD31624/2023-2024 &quot;Supply installation testing and commissioning of Inline fan for ventilation with necessary speed regulator. Makes: Ostberg/Carryaire/Kruger/Systemair&quot; 400 CFM 10MM ESP

OD31625/2023-2024 &quot;Supply, installing testing and commissioning of cabinet type Fresh Air Centrifugal Fan assembly of following capacities with backward curved DIDW/SISW centrifugal Fans with suitable motor with VFD and bypass starter, 10 micron filters for Kitchen Fresh Air makeup. The fan should be precoated, suitable for outdoor use. Makes: Nicotra/Greenheck/Systemair/Kruger&quot; 8000 CFM 35mm ESP

OD31626/2023-2024 &quot;Supply installation testing and commissioning of Inline fan for ventilation with necessary speed regulator and 10 micron filters for fresh air fan. Makes: Ostberg/Carryaire/Kruger/Systemair&quot; 450 CFM 10MM ESP

16.12.1.3 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 Thickness 1.00 mm sheet

16.12.1.2 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 Thickness 0.80 mm sheet

16.12.1.1 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 Thickness 0.63 mm sheet

16.12.2.1 Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

16.12.2.2 Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.8. mm thick

16.12.2.3 Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 1.00 mm thick

OD31616/2023-2024 Gl volume control duct damper Supply, installation, testing and commissioning of Gl volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. Gl volume control duct damper

OD31615/2023-2024 Exhaust/Fresh Air Louvers &quot; Supply and installation of powder coated aluminium air louvers with birdscreen as per the approved quality. Make: Airmaster/Systemair/Equivalent&quot;

16.15 Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

16.16.a Supplying and Fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

OD31605/2023-2024 Cabling &quot;Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. Make:Polycab/Gloster/Equivalent&quot; 4 core 4 sq mm

OD31593/2023-2024 Cabling &quot;Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. Make:Polycab/Gloster/Equivalent&quot; 4 core 6 sq mm

Fabrication Work For HVAC

OD31629/2023-2024 Supply and fabrication conveyance and installation of angle iron frame work using suitable size MS angles/flats cut and welded to shape fixing the same on floor or wall/parapet as required including painting with two coats of enamel paint over a coat of zinc chromite primer.

Kitchen Equipments

OD31825/2023-2024 Dish LandingTable With Chute, Glass Rack Bottom Cross Supports&amp; Rear Splash Sunkun Top Made Of 16G SS.Sheet. The Top Will Be Mounted On 32x32x3Mm Thick SS.Angle Frame &amp; &Oslash; 175 Mm Chute Smoothly Welded On Top, Vertical Legs Of Ss 304 16G 40x40 mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet.SS 304 . 25x25 mm Tubular Cross Bracing Welded To Legs At Rear And Both Side &amp; Front Open. Legs Shall Be Welded At Top To The SS. Angle FrameworkAnd Shall Be Positioned From The Table Ends.

OD31826/2023-2024 Loading Table With 2 Sink Unit, BottomCross Supports And Rear Splash SS 304 16G Sunk In Top Front &amp; Right Side Turned Up 75 Mm Returned 50 mm And In 12 Mm. Left Side 6 Mm Projected Out And 10 mm Down Connected To Dish Washer. Rear Side Raised Splash Of 150 Mm High,Top Welded To 32x32x3 Mm Thick SS. Angle Framework 1No. Of Ss 304 16G - 2 Sink 450x450x300 Mm Deep, Fitted With 1-1/2&quot; Bsp Waste Coupling(with sieve) Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. SS 304 16G 40x40 Mm Four Nos Of Sq. Tubular Legs With Adj. Bullet Feet. Legs Shall Be Welded At Top To The S.S. Angle Framework And Shall Be Positioned From The Table Ends. SS 304. 25x25 Mm Tubular Cross Bracing Welded To Legs At Rear And Both Side &amp; Front Open

OD31830/2023-2024 Pre Rinse Spray Unit As per Manufacturerspec. &amp; model

OD31831/2023-2024 Dish WashingMachine(H00DTYPE) winter Haulter make As per Manufacturerspec. &amp; model p-5

OD31832/2023-2024 UnloadingTable With Bottom Cross SupportsAnd Rear Splash SS 304 16 G sunk in TOP front &amp; Right side turned Up 75 mm returned 50 mm turned down 50 mm and in 12 mm. Rightt side 6 mm projected out and 10 mm down connected to Dish washer. Rear side raised splash of 150 mm high,Top welded to 32x32x3 mm thick S.S. angle framework shall be sound-deadened. SS 304 16 G 40x40 mm Four nos of tubular legs with adj. Nylon bullet feet. Legs shall be welded at top to the S.S. angle framework and shall be positioned from the table ends. SS 304 . 25x25 mm tubular cross bracing welded to legs at rear and both side &amp; front open

OD31833/2023-2024 Dish Storage Rack * 4 TIER 4 Nos 18G SS Shelves with rear &amp; sides up-beeded &amp; front down Beeded. Each shelf is supported with 20x100x20mm16G SS Channel Under Support. Uprights are made of 16G SS 38mm round tube section with AdjutableNylon Bullet Feets.. Top Side Of The Legs Should Be Closed With Nylon End Cap

OD31840/2023-2024 Dish Storage Rack-4 Tier4 Nos 18G SS Shelves with rear &amp; sides up-beeded &amp; front down Beeded. Each shelf is supported with 20x100x20mm 16G SS Channel Under Support. Uprights are made of 16G SS 38mm round tube section with AdjutableNylon Bullet Feets.. Top Side Of The Legs Should Be Closed With Nylon End Cap .

OD31850/2023-2024 Pickup CounterWith Three Side Covering,2 Under Shelves, 2 Ohs &amp; Tray Slider. Ss 304 16G Top All Side Turned Down 50 mm And In 12 mm. Top Welded To 32x32x3 mm Thick S.S. Angle Framework Or 12x50x75x50x12 Ss Channel Framework. Shall Be Sound- Deadened. 2 U/S Full Width Non-Rattling Type S.S. 304 18G With All Sides Turned Down 40 Mm And In 12 Mm And Shall Be Reinforced On The Underside With 25x100x25Mm S.S 304G Inverted Hat Type Channels. Corners Of Shelves Shall Be Cutout And Shall Be Fully Welded To The Centerline Of Legs. All Ends Shall Be Closed, Welded, Ground And Polished Smooth. 2 Over Head Shelves 12 &rdquo; Wide With S.S 304 16G Inverted Hat Type Channels, Mounted On Top By Means Of 25Mm Dia Verticals Pipe Will Be Provided, 4Nos. 40x40mm 16G SS Pipe Legs With Adj. Nylon Bullet Feet, Upper Shelf Fitted With IR Lamp Heaters - 2 Nos

OD31862/2023-2024 Work Table With Bottom Cross SupportsAnd Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends.

OD31865/2023-2024 Domestic Stove As per Manufacturerspec. &amp; mode-2 burner-make -prestiage

OD31935/2023-2024 Mixi Sujatha make Frootmix&amp; Dynamix

OD31936/2023-2024 Work Table With Sink, Bottom Shelf And Rear Splash SS 304 16G Top Front &amp; Both Side Turned Down 50 mm And In 12 mm. Rear Side Raised Splash Of 150 mm High, Top Welded To 32x32x3 mm Thick SS. Angle Framework 1 U/S Full Width Non-Rattling Type SS. 304 18G With All Sides Turned Down 40 mm And In 12 mm And Shall Be Reinforced On The Underside With 25x100x25mm SS 16G Inverted Hat Type Channels.SS 304 16G - Sink 400x400x300 mm Deep, Fitted With 1 1/2&quot; Bsp Waste Coupling(with sieve) Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. SS 304 16G 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. FrameworkAnd Shall Be Positioned From The Table Ends.

OD32181/2023-2024 Work Table With Bottom Cross SupportsAnd Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends.

OD32182/2023-2024 MocrowaveOven - IFB As per Manufacturerspec. &amp; model-30 Ltr capacity

OD32184/2023-2024 Tilting Wet GrinderCosmos SS 304 16 Swg SS Drum Revolving Drum, Grinding Stone, Frame All Ss Moter: Crompton/AbbEle: 0.5 Hp/3Ph/50Hz

OD32188/2023-2024 Tilting Wet GrinderCosmos SS 304 16 Swg SS Drum Revolving Drum, Grinding Stone, Frame All Ss Moter: Crompton/AbbEle: 0.5 Hp/3Ph/50Hz

OD32192/2023-2024 Coconut Scrapper with stand Cosmos As per Manufacturerspec. &amp; model.

OD32193/2023-2024 Pot Rack - 3 Tier 38Mm Dia*16G Ss Pipe Uprights With Adj. Nylon Bullet Feets With Ss Bush Nylon End Closer 32Mm Dia*16G Ss Pipe Cross Supports 18 Mm Dia*16G Ss Pipe Cross Supports At 100MmC.T.C. Apx.

OD32195/2023-2024 Work Table With Bottom Cross SupportsAnd Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends.

OD32197/2023-2024 Single Sink Unit With Bottom Cross SupportsAnd Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort. Sink 400x400x300 Mm Deep, Fitted With 1-1/2&quot; Bsp Waste Coupling(with sieve) Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends

OD32199/2023-2024 Hot Plate With BottomShelf And Rear Splash 16 SWG SS top with 150 mm high raised splash on rear, returned 50mm &amp; down. Both sides of top rolled down 50 mm flush with body cladding. Worktop to over hang the base body by 50mm from front and 75mm at rear. SWG 20G (304) SS on all sides with air vents on both sides. 40x40 SQ PIPE &amp; 25x25x3 MM SS Angle boxed frame under support. Cooking top of 20 mm thick polished MS plate with 75 mm raised rear and side edges with grease collecting trough in front and grease collecting drawer. 2Nos. of V-600 burners (40,000 btu/hr) with One number Pilot Burner. 16 SWG , 40x40mmSS Square pipe legs with adjustable SS bullet

OD32200/2023-2024 SpreaderTable With Two Under Shelves &amp; Rear Splash 16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm.4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet

OD32219/2023-2024 3 Burner Cooking Range With 1 Under Shelf &amp; Rear Splash SS 304 16G Top Front &amp; Both Side Turned Down 50 mm And In 12 mm. Rear Side Raised Splash Of 150 mm High, &amp; 32x32x3 mm SS Angular Framework Fully Welded. 3 Nos. 350x350 mm, Heavy Duty Cast Iron Removable Vessel Rest. 2 Nos G10 Burners &amp; 1No Model-4 Burner(Canteen Burner) With Pilot &amp; Control. Swg 20 (304) SS Spillage Tray With SS Strip Handle.1 U/S Full Width Non-Rattling Type SS. 304 18G With All Sides Turned Down 40 mm And In 12 mm And Shall Be ReinforcedOn The UndersideWith 25x100x25mm SS 304 16G Inverted Hat Type Channels. Corners Of Shelves Shall Be Cutout And Shall Be Fully Welded To The Centerline Of Legs. All Ends Shall Be Closed, Welded, Ground And Polished Smooth. Legs Four Nos SS 304 16G 40x40 mm TubularLegs With Adjustable.Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS.Framework And Shall Be Positioned From The Burner Ends.

OD32240/2023-2024 Single Sink Unit With Bottom Cross SupportsAnd Rear Splash SS 304 16G Top Front &amp; Both Side Turned Down 50 mm And In 12 mm. Rear Side Raised Splash Of 150 mm High, Top Welded To 32x32x3 mm Thick SS. Angle Framework. SS 304 16G - Sink 400x400x300 mm Deep, Fitted With 1-1/2&quot; Bsp Waste Coupling Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. SS 304 16G 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. FrameworkAnd Shall Be PositionedFrom The Table Ends.

OD32241/2023-2024 2 Burner Cooking Range With 1 Under Shelf &amp; Rear Splash SS 304 16G Top Front &amp; Both Side Turned Down 50 mm And In 12 mm. Rear Side Raised Splash Of 150 mm High, &amp; 32x32x3 mm SS Angular Framework Fully Welded. 2 Nos. 350x350 mm, Heavy Duty Cast Iron RemovableVessel Rest. 1 No G10 Burners &amp; 1No Model- 4 Burner(CanteenBurner) With Pilot &amp; Control. Swg 20 (304) SS Spillage Tray With SS Strip Handle.1 U/S Full Width Non-Rattling Type SS. 304 18G With All Sides Turned Down 40 mm And In 12 mm And Shall Be Reinforced On The Underside With 25x100x25 mm SS 304 16G Inverted Hat Type Channels. Corners Of Shelves Shall Be Cutout And Shall Be Fully Welded To The Centerline Of Legs. All Ends Shall Be Closed, Welded, Ground And Polished Smooth. Legs Four Nos SS 304 16G 40x40 mm Tubular Legs With Adjustable.Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS.Framework And Shall Be Positioned From The Burner Ends.

OD32243/2023-2024 SpreaderTable With Two Under Shelves &amp; Rear Splash 16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm.4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet

OD32244/2023-2024 Centre Table With Bottom Shelf

OD32245/2023-2024 2 Door Work Top Under Counter Chiller HoshizakiRTW-156MS4 As per Manufacturerspec. &amp; model

OD32393/2023-2024 3 In 1 Bulk Cooking Range 16G SS 304 Work Top Double Beeded On All Sides 32x32x3 mm Thick SS Angle Frame under supoort. 40 mm Sq. Pipe &amp; 35x35x3 mm SS Angular Framework Fully Welded. One 40 sq. mm, Heavy Duty Cast Iron Removable Vessel Rest. One No Of /G-9 OR 1No Model-4 Burner(CanteenBurner) With Pilot And Controls. One No 20 SWG (304) SS Spillage Tray With SS Strip Handle. Manifol&frac12; Inch Dia Provided On Both Sides. 4 No&rsquo;S 40 Sq. Mm 16G SS Legs With AdjustableFeet.

OD32395/2023-2024 4 Door VerticalChiller Hoshizaki HRW147MS4 As per Manufacturerspec. &amp; model

OD32398/2023-2024 Veg. Crate Trolley 25x25mm SS 304G 16G SS Square tube construction with 16G SS Sliding Chanels to accommodate 9 Nos of Vegetable crates of size 600x400x250mm-3 Nos, 600x400x150mm-3 Nos,600x400x100mm-3 Nos, Unit will be mounted on 4 Nos All swivel rubberised castors (2 Nos with break)

OD32399/2023-2024 Work Table With Bottom Cross SupportsAnd Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends.

OD32401/2023-2024 Veg. Cutter (Table Top) Cosmos VG50 As per Manufacturerspec. &amp; model

OD32403/2023-2024 GarbageBin Trolley Standard Design - Nilkamal

OD32404/2023-2024 Work Table With Sink, Bottom Shelf And Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort.2 Sink 450x450x300 Mm Deep, Fitted With 1-1/2&quot; Bsp Waste Coupling(with sieve) Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be Positioned From The Table Ends.

OD32414/2023-2024 Work Table With Sink, Bottom Shelf And Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends.

OD32416/2023-2024 Wall Mounted Shelf - 2 Tier 2Nos 18G Ss Shelves With 3 Side Up-Beeded &amp; Front DowBeeded, 2Nos. SS Brackets Of Size 290*150mmWith 2Nos. 10 mm Dia Holes In Each Bracket

OD32419/2023-2024 Work Table With Sink, Bottom Shelf And Rear Splash 16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3MmThick SS Angle Frame under supoort.2 Sink 450x450x300 Mm Deep, Fitted With 1-1/2&quot; Bsp Waste Coupling(with sieve) Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. 16G SS Splash, One No 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mmunder support. 16G SS 40x40 Mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS. Framework And Shall Be PositionedFrom The Table Ends

OD32422/2023-2024 Nylon ChoppingBlockWith Stand 38x38x3mm SS Angle top frame work with 40x40 16G SS 304 Square tube legs and bottom cross braced with 25x25mm16G SS Square tube. Unit will have 150mm rear splash and White Nylon Chopping board of size 600x700x50mmThick reversible type.

OD32423/2023-2024 Onion / Potato Bin Trolley SS 3mm Thick SS Welded mesh construction with top openable lid. Lid also with SS Mesh Construction. Bottom 18G SS Sheelt slopping towards the outlet mouth, SS Lift off door for mouth, Unit will have 4 Nos Nylon heavy duty castors.

OD32428/2023-2024 Storage Rack-5 Tier5 Nos 18G SS Shelves with rear &amp; sides up-beeded &amp; front down Beeded. Each shelf is supported with 20x100x20mm16G SS Channel Under Support. Uprights are made of 16G SS 38mm round tube section with AdjutableNylon Bullet Feets.. Top Side Of The Legs Should Be Closed With Nylon End Cap .

OD32431/2023-2024 Storage Rack-5 Tier 5 Nos 18G SS Shelves with rear &amp; sides up-beeded &amp; front down Beeded. Each shelf is supported with 20x100x20mm16G SS Channel Under Support. Uprights are made of 16G SS 38mm round tube section with AdjutableNylon Bullet Feets.. Top Side Of The Legs Should Be Closed With Nylon End Cap

OD32432/2023-2024 Ss Drain TroughWith Gratings SS 304 25x4 MM Outer Frame Structure, Inside The Frame 25 X 3 MM SS Flats Horizontally &amp; Grooved Flats Vertically Welded Together, Ss 304 16G Trough Fully Welded Body, Designed To AccommodatGratings, Bottom Of Trough Scoped Towards The Center. &Oslash; 95 Mm Tubular Outlet At The Center. Ss 304 18G Perforated ( &Oslash; 3 Mm Holes, 9 Mm Ctc With &Oslash; 8 Mm Ss Rods On Both Sides.) Basket Basket Throughout The Length &amp; No Perforation To Be Made At Bending Areas &amp; Top Seating Edge.(Perforated 18G 304Ss Stainer Throughout The Length)

OD32434/2023-2024 Wall MountedExhaustHood With Baffle Filters( Dish Washer) SS Wall Mounted Type Exhaust Hood Of Ss 304 20G SS 304 Grade, Center Partition 304 16G Ss Along With Baffle Type Grease Filters Of Ss.304 Grade 18G Frame And Vapour Proof Led Light Fittings,Oil CollectionTray , WeldedContruction

OD32436/2023-2024 Island Type ExhaustHood With Baffle Filters(3 Burner,HotplateEtc) SS Wall Mounted Type Exhaust Hood Of Ss 304 20G SS 304 Grade, Center Partition 304 16G Ss Along With Baffle Type Grease Filters Of Ss.304 Grade 18G Frame And Vapour Proof Led Light Fittings,Oil CollectionTray , WeldedContruction

OD32438/2023-2024 Wall MountedExhaustHood With Baffle Filters(Bulk) SS Wall Mounted Type Exhaust Hood Of Ss 304 20G SS 304 Grade, Center Partition 304 16G Ss Along With Baffle Type Grease Filters Of Ss.304 Grade 18G Frame And Vapour Proof Led Light Fittings,Oil CollectionTray , WeldedContruction

OD32440/2023-2024 TransportationLoading and uloading

Gas Pipeline Work

OD32447/2023-2024 Supply, Installation, Testing &amp; Commissioningof Manifold for (4+4) VOT Cylinder fabricated with 25mm schedule 40 SS pipe of Jindal with flanged ends, heavy duty lugs duly welded and provision for pressure gauge safety valve mounting.It shall include Pipeline Arrangement with internal fixtures including Clamping ,Forged SS Fixtures, Seamless Fixtures.Including Welding,Accessories,labour,testing and Commissioning Charges Make:Fabricated

OD32449/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG High Pressure Click on Adaptors 25.6 mm with all fittings Make:TVL,Equivalent.

OD32452/2023-2024 Supply, Installation, Testing &amp; Commissioning of Suraksha Pigtail 1/2&quot; X 1/2&quot; 3 Ft Make:Suraksha/SaiFlex/Equivalent.

OD32453/2023-2024 Supply, Installation, Testing &amp; Commissioning of Non Return Valve 1/2&quot; for Manifold Make:Gasman,Equivalent.

OD32454/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG Y Type Filter 15mm Make:Lintas,Equivalent

OD32455/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG Pressure Gauge 0-100 Psi 4&quot; Dial SS Body Make:Indosonic/Feibig/Equivalent.

OD32457/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG Regulator Adjustable Type REG -2301 Make:United/Equivalent.

OD32459/2023-2024 Supply, Installation, Testing &amp; Commissioning of Flame Arrestor 15 mm Make:United/Equivalent.

OD32472/2023-2024 Supply, Installation, Testing &amp; Commissioning of 15 mm Brass Ball Valve with SS handle Make:Arkay/Srp/Equivalent.

OD32485/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG RegulatorAdjustableType REG -2 with all fitings Make:United/Equivalent

OD32497/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG Pressure Gauge 100 Psi 4&quot; Dial SS Body Make:Indosonic/Feibig/Equivalent.

OD32499/2023-2024 Supply, Installation, Testing &amp; Commissioning of LPG Regulator adjustable type 4B0.5 With all fittings Make: United

OD32500/2023-2024 Supply, Installation, Testing &amp; Commissioning of M.S.Seemless Sch-40 -15MM (With all fittings Two coated MRF Epoxy Primer &amp; MRF Epoxy Paint)The installation must fully comply with the IS standard Make:Jindal

OD32531/2023-2024 Supply, Installation, Testing &amp; Commissioning of Clamp 15mm* 35mm [SS 202]

OD32553/2023-2024 Supply, Installation, Testing &amp; Commissioning of Clamp 25mm* 55mm [SS 202]

OD32552/2023-2024 Supply, Installation, Testing &amp; Commissioning of 15 mm Brass Ball Valve with SS handle Make:Arkay/Srp/Equivalent

OD32554/2023-2024 Supply, Installation, Testing &amp; Commissioning of Suraksha Pigtail 1/2&quot; x 1/2&quot; -5 Ft [Black] Make:Suraksha/SaiFlex/Equivalent

OD32555/2023-2024 Supply, Installation, Testing &amp; Commissioning of 3 Module System with 3 sensors, 1 panel external Hooter &amp; Auto &ndash;Shutoff, With Solinod Valve

OD32556/2023-2024 Supply and laying of Armoured Cable 1.5 SQMM 4 Core Copper Shielded Make:Surabhi/Equivalent

OD32557/2023-2024 Thread Rod, Barrel Nipple ,Flange, Clamp, MS Fittings, Wall opening, loading and unloading charges including all other Expenses

Plumbing Works

OD157/2024-2025 Providing and fixing Table Mounted sink cock with swinging type of approved quality Make: Hindware/Jaquar/Parryware/Equivalent

OD158/2024-2025 Providing and fixing Table Mounted sink mixer with swinging type of approved quality Make: Hindware/Jaquar/Parryware/Equivalent

OD159/2024-2025 Providing and fixing CP brass braided Hose with 2nos 15mm nuts and washers without Ninpple of approved quality 15 mm nominal bore with 45 cm length

OD160/2024-2025 Providing and fixing Bib cock with Nozzle of approved quality Make: Hindware/Jaquar/Parryware/Equivalent

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

OD161/2024-2025 Supply, fixing and testing of storage vertical/Horizontal type water heater of Approved make high rated pressure withstand capacity including all fittings &amp; fixture inside, polypropylene cover non return valve, 1no. Gate valve all as per IS 2083-195, with 3 core heavy duty copper cable with 3 pin plug, automatic pressure release valve adjustable thermostat, angle valve,thermal cutout, puf insulation, tested for 7Kg pressure, etc.complete, &amp; bracket painted with two coats of enamel paints. Incusive of all fittings. with angle valve

50.18.8.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.9.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

OD177/2024-2025 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 150 mm pipe 6kgf/cm2

50.18.7.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.9.1 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling &amp; testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling &amp; testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

OD167/2024-2025 Providing , fixing , testing and commissioning pvc &quot;P&quot; trap with multy inlet or single inlet connection of required sizes of self cleansing design with or without vent arm complete, including cost of masonry or concrete supports cutting and making good the walls and floors where ever required

OD168/2024-2025 Providing and fixing PVC Adapter Boss of approved quality 110 x 50 mm&quot;

OD170/2024-2025 Providing, fixing, testing and commissioning at site C.P. or stainless steel Grating Cover with protection from cockroaches of matching size of multi inlet or &quot;&quot;P&quot;&quot; trap complete in all respects. 5&quot;&quot; Frame with 4&quot;&quot; Openable Lid/Grating&quot;

OD169/2024-2025 Providing and fixing two piece CP , air tight floor clean out plug of approved quality . 125mm square frame with 100 mm dia openable circular lid .

OD171/2024-2025 Providing and fixing GI slotted rail of approved design. projecting 75 mm outside the wall surface and fixed on wall with 2 nos, 6/8 mm dia expansion hold fasteners, including drilling necessary holes in brick wall / CC / RCC surface and the cost of bolts included. The pipes shall be fixed to the already fixed brackets with the help of 8 mm galvanised GI &quot;U&quot; bolts of specified shape and shall be fixed with GI nuts, bolts, &amp; washers of suitable size, one bolts on each side of the pipe.

OD172/2024-2025 Supply and fixing of 600x600mm DI MD (B-125) manhole cover of approved quality&quot;

OD173/2024-2025 Providing and fixing square-mouth pvc gully trap complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :150 x 100 mm size P type, With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 R.C.C. top slab (for fixing gratings) with 1:2:4 mix (1 cement : 2 M sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 M sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc.: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

50.18.9.22.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.3 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.8 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

OD178/2024-2025 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Y

OD162/2024-2025 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia Elbow

OD163/2024-2025 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia 45 degree Elbow

OD164/2024-2025 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia Bend

OD165/2024-2025 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia Y

OD166/2024-2025 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia Socket Coupling

18.8.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &amp; cold water supply, including all CPVC plain &amp; brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes&amp; fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &amp; cold water supply, including all CPVC plain &amp; brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes&amp; fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.7.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &amp; cold water supply, including all CPVC plain &amp; brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work Exposed on wall20 mm nominal outer dia pipes

18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &amp; cold water supply, including all CPVC plain &amp; brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work Exposed on wall25 mm nominal outer dia pipes

OD174/2024-2025 Providing and fixing Gun Metal / Forged Brass Ball valve of approved quality of following sizes. Make: Zoloto/SKS/Cim/Equivalent&quot; 20mm dia

OD175/2024-2025 Providing and fixing Gun Metal / Forged Brass Ball valve of approved quality of following sizes. Make: Zoloto/SKS/Cim/Equivalent&quot;

OD176/2024-2025 Drilling/Core Cutting of required dia outlets using low vibration mechanical means. Cost to include closing of core cut using appropriate sealant with necessary form work, staging, tools, etc., ( if required) RCC Beams (Up to 30 cm Thickness) 110mm-125mm

Exterior Works

OD739/2024-2025 Eave board: Providing and fixing CNC cut Eave board with PU paint finish as per design intent. Eave board to be finished with 18mm thick Multiwood (Make :Thomson/Equivalent) with CNC Cut design of 25cm height fixed on to existing framework using screw as per the drawing. Including all cost of accessories, labour charge etc. complete.

Interior Works

21.1.1.3 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPolyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron )

21.1.2.3 For shutters of doors, windows &amp; ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micorn)

OD746/2024-2025 Providing and fixing 9 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness

9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

21.13 Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

9.97.4 Providing and fixing aluminium tower bolts,ISI marked, anodised( anodic coating not less than grade AC 10 as per 1868), transparent or dyed to required colour or shade, with necessary screws complete: 150x10mm

OD773/2024-2025 Door Closer : Providing and fixing Door Closer ( DC 602 Surface Mount Door Closer Hold Open Arm EN2/3 Dr Wt 45-60 kgs - ALU,Make; Hafele,Hettich/Equivalent), with necessary accessories and screws etc. complete.

OD775/2024-2025 Door Stopper : Providing and fixing Door stopper(Door Mounted Hanging door Stopper 255, Make:Hafele,Hettich/Equivalent)with necessary screws etc. complete as per direction of Engineer -in-Charge. Single rubber stopper.

EXCLUSIVE OF GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of Insurance,Transportation, delivery and installation cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

5.CEMENT: Make use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

6.RCC: (Assessment of strength of concrete by Cube testing at Approved Govt labs as per IS) Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

7.STEEL REINFORCEMENT: Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference

8.CENTERING & SHUTTERING: (Centering and shuttering for different category of work may be considered separately.)

9. SOLID BLOCK MASONRY: Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered)

10.ELECTRICAL: Note: Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

11.VITRIFIED FLOOR TILES/ CERAMIC GLAZED WALL TILES: Make: Khajaria, Jhonson, RAK, NITCO, Cera or Eq. in the order of preference and prior sample approval from KEL, Client

12.ALUMINIUM WORK: Make: INDAL, JINDAL in the order of preference and prior sample approval from KEL, Client

13.Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

14. ACRYLIC SMOOTH EXTERIOR PAINT/ SYNTHETIC ENAMEL PAINT/WHITE CEMENT BASED PUTTY/ CEMENT PRIMER: Make: Asian, Berger, Nerolas or eq. in the order of pref.

CUBIX INFRASTRUCTURES (BID ID -2278690)

meconconstructions (BID ID -2279437)