Construction of Girls Hostel for Nursing Students (G1) (2nd Call)

Earth work in excavation by mechanical means(Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 mtr in width as well as 10 sqm on plan) in all kinds of soil including rock and disposal of surplus, excavated earth at dumping sites to be purchased by the contractor and approved by the engineer-in-charge at site for safe disposal of same without damaging private /public property and all required leads/lifts and carriage.(Complete job) in 80 AKS 10 OR 10 HR

Earth work in trench excavation by manual means in AKS

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate) 40mm nominal size crushed.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. in 1:1.5:3

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). with 20% boulders

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:6 (1 cement : 6 fine sand).

Extra for brick masonary above plinth level

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars.

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand).

Providing and laying in position cement concrete of specified grade including the cost of shuttering all work upto Plinth level in 1:4:8 stone aggregate) 40mm nominal size crushed stone aggregate including curing

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M.

Hand Packed stone filling including supply of stones

Centering and shuttering including strutting, propping etc. and removal of form work for :-

Foundations, footings, bases of columns.

Columns, pillars, piers.

Lintels, beams,

Suspended floors, roofs, landings and access platforms.

Wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc

Stair Case

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities stairs etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge for granite work

Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Premium quality conforming to IS : 13755 of ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles 300X600mm conforming to IS : 13753 of minimum thickness 5mm of approved make like SOMANY, KAJARIA or equivalent make in all colour, shades except burgundy, bottle green, black of any size as approved by Engineer in charge over 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : second class deodar wood.

Providing and fixing handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper.

P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.).

Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacture,over the plasterted wall surface to prepare the surface even and smooth complete

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Finishing wall with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.on steel/wood work

Providing and laying 60 mm thick interlocking paver blocks of M30 grade over sand bed including locking all complete

Applying coat of water thinable primier on wall surface

Providing and laying 50 mm thick DPC in cement concrete 1:2:4 including curing complete

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

providing/fixing chromium plated brass curtain rod having thickness of 1.25 mm including fixing with CP brass screws

Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete.

Sand for an average lead of 120 kms

Stone aggregate fo r an average lead of 20 Kms.

Bricks for an average lead of 150 Kms

Stones 5 km by MT

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid.(make Essel,Kerovit,Euronics, Jaguar )

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps..(make Essel,Kerovit,Euronics, Jaguar )

Providing and fixing of CP brass sink mixer with regular swinging spout with connecting legs (jaquar ,Hindware kerovit etc)

Providing/fixing Robe Hook of approved brand and manufacture jaquar Hindware kerovit etc

Providing and fixing soap dish holder

providing and fixing bottle trap

providing and fixing waste coupling for washbasin and sink of jaquar Hindware etc

providing and fixing single lever exposed diverter ( jaquar)

providing and fixing stroring installating testing and commissioning of vertical and horizontal storage type gyser with all accessories ( complete job)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing stainless steel kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. .(make Essel,Kerovit,Euronics, Jaguar )

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore (Make Jaquar CQT 23059 / Kerovit make Cat No. KB 1511003/ Euronics EAV01).

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing brass bib cock of approved quality. 15 mm nominal bore (make Essel,Kerovit,Euronics, Jaguar )

Providing and fixing PTMT grating of approved quality and colour.Circular type 125 mm nominal dia with 25mm waste hole

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet (150 mm dia)

Providing and fixing of Polyethylene/Aluminium/Polyethylene (PE-AL-PE) Composite Pipes as per IAPMO IGC- INDIA 308, UMC-1TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer’s name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC /FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers

Connectors, clamps at one meter spacing, with PAP valves etc. Make Kitec , Maithilee and Vista. Concealed installation including cutting chases and making good in the wall etc, Complete in all respect.

1216 (16mm OD) pipe.

1620 (20mm OD) pipe.

Providing and fixing Polyethelene-Aluminium–Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IAPMO-IGC-INDIA 308. U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature upto 80 0C, including all special fittings of composite material (engineering plastic blend and and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connector etc. with trenching, refilling and testing of joints complete as per direction of the Engineer-in-charge. External work. including all necessary fittings

2025 (25mm OP) pipe.

2532 (32mm OP) pipe.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, complete copatable to connection with composite pipe make :Rehau / Kitech/gebbrat ) including all necessary fittings

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work)

15 mm dia. nominal bore (Medium)

20 mm dia. nominal bore (Medium)

25 mm dia. nominal bore (Medium)

15 mm dia. nominal bore (Medium)

20 mm dia. nominal bore (Medium)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work

15 mm dia. nominal bore (Medium)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

25 mm dia. nominal bore(Medium)

Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed.

Providing and fixing on wall face unplasticised-Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter.MAKE Supreme, asirwad, prince,jain with. All necessary fittings and Accessories as per the Direction of Engineer Incharge.

75MM pipe

110MM pipe

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :-

Coupler 110mm.

Single tee with door 110 x 110 x 110mm.

Bend 87.5* 110mm.

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate)

Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license)