SPECIAL REPAIRS TO P-179, MAIN GATE, SQUASH COURT AND ADDN/ ALTN TO BLDG NO. P-48 AT NAVAL BASE

Amount

Demolition of concrete (Reinforced) of any description and in any position not otherwise specifically provided for cement concrete (reinforcement cut as required to facilitate demolition) complete including removing debries ouside MD land all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete (unreinforced) complete including removing debries outside MD land all as specified and directed.

M&L for form work to sides of Columns, complete surface to be fair finished all as directed by Engr-in-Charge.

M&L for form work to chajjas including edges etc fair finished, complete all as specified and directed.

M&L for form work to sides and soffits of suspended slabs such as roof slabs, floor slabs and similar work N exc 200 mm thick (horizontal or sloping) fair finished complete all as specified and directed.

M & L for RCC type M-30 (using 20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, andings, balconies, canopies, deck slabs and in shelves etc, complete all as specified and as directed

M & L for RCC type M-30 (using 20 mm graded stone aggregate) as in Chajjas complete all as specified and as directed

M&L for Reinfoced cement concrete (Nominal Mix) type B1, 1:2:4 (20 mm graded aggregate) as in columns etc. complete all as directed by Engr-in-Charge.

M&L for Reinfoced cement concrete (Nominal Mix) type B1, 1:2:4 (20 mm graded aggregate) as in footing, base for columns etc. complete all as directed by Engr-in-Charge.

M&L for precast reinforced cement concrete M-15, factory made including reinforcement of required size using 20mm graded stone aggregate set in CM(1:4) as in cover slab ( for manhole, drain cover etc) including use & waste of form work for fair finished surfaces complete all as specified and directed

Dismantling Structural steel work including doors, gates but excluding framed truss etc as in gates complete all as specified & directed by Engr-in-charge.

S & F TMT steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia.

All as per above item No 12.00, but 6 to 8 mm dia in stirrups

S&F Mild steel pipes/ rolled sections Fe 410 -W (Gde- E- 250) quality- A as in framing for cladding, rafters; purlins fixed with angle cleats or other connecting plates all as specified & directed by Engr-in-charge.

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm but n exe 10cm long and dia of neck 11 to 15 mm complete all as specified and directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantling complete all as specfied and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (Fe 410 -W (Gde- E- 250) quality- A) complete all as specfied and directed.

M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, Gates, Grating drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as specifed and as directed by Engineer in Charge.

Taking down Shutters of any description n exc 1 sq. m each and removing complete all as specified and directed.

Taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each and removing complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4 sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified and directed.

Taking down chowkats or frames in windows exceeding 1.5 sqm but not exceeding 4 sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified and directed.

S&F 30mm thick 1st class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed

S&F factory made 30mm 2 class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and directed.

S&F fiber glass reinforced plastic (FRP) door frames of three legged of cross section 90 x 45 mm having single rebate of 32 x 15 mm to receive shutter of 30 mm thick. The laminate door frame moulded with fire retardent grade unsaturated polyster resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block of 2nd Class Hardwood in all the three legs. The frame shall be covered with fibre glass from all side M.S stay shall be provided at the bottom to sedy the frame complete as per direction of Engineer - in - Charge.

S&F 30 mm thick glass fiber reinforced plastics paneled door shutter of required colour & approved colour and manufactrures made with fire retardent grade unsaturated polister resin,moulded to 3mm thick FRP laminate for forming hollow rails & styles with wooden frame & suitable blocks of seasoned wood inside at required places for fixing of fittings along with MS tube frame of 19 gauge all around the styles & rails duly coated with steer primer cast monolithically with 5mm thick FRP laminate forpanels & conforming to IS:14856:2000 including fixing to frames. The shade & colour shall be approved by Engineer-in-Charge

S&F 300mm long (Length of Bolt in mm) Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F 250mm long (Length of Bolt in mm) Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F 200mm long (Length of Bolt in mm) Aluminium anodised,barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 150mm (Size of Handle in mm) Extruded aluminium alloy handles, fabricated type,anodised all as specified.

S&F in repair powdercoated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handels 2 Nos in each door, hinges, anodised alumnium snap beading, screws etc. complete all as specified

S & F Plain colour PVC sheet 2mm thick fixed or laid on to aluminium doors by using rubber based adhesive, supplying & fixing at site as per specification

S&F in repairs powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

Supply and fixing of power coated three track anodised aluminium frame section of 0.933 kg/RM of sliding tracking section for windows, partition wall, cup board with one or more rebates including tracking section of windows cleats for fixing etc, complete all as specified and directed.

S&F in repair Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F in repairs Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples all as specified.

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

M&L preparation of new wooden surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of old wooden surfaces of any description exceeding 10 cm width or grith not otherwise specified and applying one coat of syntheic enemal paint complete all as specified and as directed.

Material and labour for preparation of old surfaces of ceiling including cornicess plaster etc for lime wash (white washing) and applying one coat of white wash on ceiling complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on steel or iron surfaces of any decription, over 10 cm in width or grith, not othewise described including preparation of old painted surfaces complete all as specified and directed.

M&L two coats of white wash on newly plastered surfaces of walls including of preparation of surfaces, complete all as directed.

M&L for preparing of new or priviously untreated steel surfaces, over 10cm in width or girth,not otherwise described including washing and cleaning etc., and applying 2 coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old treated steel surfaces of any description (Steel gates , Embedded Angles etc), over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

Material and labour for preparation of old plastered surfaces and applying two coats of white wash on ceiling complete all as specified and as directed.

M& L for preparation of old plastered surfaces of wall by complete removal of existing treatment and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth and distempering with 1st quality acrylic distemper with two or more coats (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as per manufacturer's specification complete all as specified and directed

M& L for applying plaster of paris putty of 2 mm thickness over new plastered surface to prepare the surface even and smooth and distempering with 1st quality acrylic distemper with two or more coats (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as per manufacturer's specification complete all as specified and directed

M& L for preparation of old plastered surfaces of wall by complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm to prepare the surface even and smooth of required shade and colour as per manufacturer's specification complete all as specified and directed.

M& L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces to prepare the surface even and smooth of required shade and colour as per manufacturer's specification complete all as specified and directed.

M & L Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete all as specified and directed.

S&F 4.8 mm thick Sheet glass,ordinary quality pin headed type and glazing with Aluminium snap beading with rubber Neoprene packing in square exc 0.5 sq. m in each pane all as specified and as directed

M&L for Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers exc 1.5 sqm

Taking down aluminium decogrills and refixing in the same opening including cutting of decogrills if required etc all as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premisess complete all as specified and as directed

M&L for non-skid ceramic tiles, white/coloured (of approved shade and design), 7 to 8mm thick, of superior quality, square / rectangular (area exceeding 0.06 Sqm but not exceeding 0.11 Sqm) joint free, as in floors, etc.set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match shade of tiles laid over & including 15mm thick screed bed in CM (1:6) complete all as specified and as directed

M&L for coloured Glazed ceramic tiles, of size 300x200x 7 to 8mm thick of superior quality fixed on vertical surfaces such as skirting / dado / risers of step etc.,set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles fixed over & including backing coat of 10mm thick plaster in CM (1:4) complete all as specified and as directed.

M&L for Light shade vitrified ceramic tiles, premium quality, coloured (of approved shade and design), 10mm thick, of superior quality, (square / rectangular) polished, area of each tiles not exceeding 0.36sqm,joint free, as in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles ,laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Ditto all as per above item No. 58.00 but Dark shade complete all as specified and as directed.

Ditto all as per above item No. 58.00 but vertical surfaces such as skirting, dados etcincluding screed bed layer 10mm thick in cement mortar 1:3 finished even and rough for receiving tiles on vertical surfaces complete all as specified.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons, compound wall etc.laid dry beded in any mortar complete all as specified.

M&L 20mm thick Granite work in steps, jambs, pillars, window-cills, cooking platforms laid over CM 1:4 , 15mm thick cement screed and jointed with grey cement slurry, and pointed with white cement with admixture ofpigment to match the shade ofgranite stone including grinding and polishing complete all as specified

M&L Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including back coat layer of 15mm thick in cement mortar 1:3 finished even and rough for receiving tiles on vertical surfaces complete all as specified.

S & F in repair to (incl Dismantling) 18-19mm thick pre-laminated particle board, flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade having one side decorative lamination and other side balancing white lamination as in cup board shutter , shelves etc including 6 mm thick teak wood leaping on three sides and 20mm thick on hanging side & French polishing to edging complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

Repair and refixing of aluminium window shutter to make it openable/slide smoothly, including cutting, repair/change of all necessary fittings/fixtures for window like cleates , locking arrangements glazing cleats and cadmium plated stainless steel screws including rubber gaskets beadings etc complete all as specified and as directed by Engr in charge

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed

Dismantling water tanks exc 500 ltr & not exc 1000 ltr and removing to store Complete all as spd and as directed by Engineer in Charge

Disconnecting existing tanks upto 1000 ltr Cap , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position with Cleaning , repairing,incl complete connection with inlet and outlet with GI / CPVC pipe fitting , Float valve etc Complete all as spd and as directed by Engineer in Charge

S&F Rotational moulded polyethylene water storage tanks of cap 1000 Ltr Cap (cylindrical vertical with closed top) hoisted and fixed in position with inlet outlet with suitable PVC Float Valve etc connections all as specified in SSR Part I Complete all as spd and as directed by Engineer in Charge

S&F Rotational moulded polyethylene water storage tanks of cap 2000 Ltr Cap (cylindrical vertical with closed top) hoisted and fixed in position with inlet outlet with suitable PVC Float Valve etc connections all as specified in SSR Part I Complete all as spd and as directed by Engineer in Charge

Supplying and laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 16mm pipe outer dia, Complete all as specified and directed.

Supplying and laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 20mm pipe outer dia, Complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and Labour for 15mm thick rendering on fair faces of brick work or concrete surfaces or Porbandar stone masonary in cement mortar 1:4 finished even and smooth with out using extra cement complete all as specified and as directed.

Material and Labour for 5mm thick rendering on concrete surfaces in cement mortar 1:3 finished even and smooth with out using extra cement on ceiling complete all as specified and as directed.

S&F in repair Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified.

S&F in repair Vitreous China soap tray embedded in the wall complete all as specified.

S&F in repair Glass shelf assembly complete all as specified.

S & F of 15mm bore pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, as in repair complete all as specified.

S & F of 15mm Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in repair complete all as specified.

S&F in repairs Waste fittings,32 mm brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.

S&F in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, whiter with inlet, ball valve, float and handle including brackets, connection to pipes, flush pipe to pedestal pan, including all joints, complete all as directed by Engr-in-charge.

S&F in repairs Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device suitable for European / Anglo indian type WC all as specified and directed.

S&F in repairs CP swivel shower 100mm dia with arm 15mm bore, 195 mm long with bend of 45 degreee with flange any colour for fixing with 15mm pipe complete all as specified and as directed.

S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F in repair Tubular Towel Rail 20mm dia D type 60cm long between flanges of brass chromium plated complete all as specified and as directed.

S&F in repair 15mm Bib taps,chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repair 15mm Stop valves, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair Door closer hydraulically regulated, designation No. 3, universal type, Aluminium (extruded section body) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F 375mm, Brass ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Taking down old roof treatment of any description including plaster, cement concrete etc. and removing old material outside MD land exc 1Km and not exceeding 5 Km completely all as specified and directed by Engineer - in - Charge.

M&L for 10 mm thick (average) plastering on concrete surfaces in cement mortar 1:4, in order to maintain proper slope and base over existing roof surfaces for laying of APP based polymeric membrane, add WPC @3% of cement weight(WPC paid separately), finished even and smooth without using extra cement complete all as specified and as directed. (Note:- Polymeric membrane will be measured and paid separately)

Supply only integral waterproofing compound

M&L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment/ specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 4 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non wovwn polyster fabric or weight not less 160 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm minimum and then inserted insde the groove of parapet wall and shall be finished by a membrane flashing. (Note:- (i) Laying of APP based membrane shall be done by torch on method or as per manufacturers instruction. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instruction. (c) Applying two coats of reflective Bituminous aluminium paint on top of APP membrane.

S&F in repair PVC (SWR) bends any radius laid in trenches of nominal bore 110mm complete all as specified and directed

S&F in repair PVC (SWR) pipes single socketed in any length with necessary joints laid in trenches / fixed to walls of nominal bore 110mm including excavation and dismantling of old pipe complete all as specified and directed

All as per item No. 102.00 above but nominal bore 75mm

S&F in repair PVC (SWR) bends with cap any radius of nominal bore 110mm complete all as specified and directed

All as per item No. 104.00 above but nominal bore 75mm

S&F in repair PVC (SWR) branch piece, single (single Y) equal or unequal of nominal bore 110mm complete all as specified and directed

All as per above item No. 106.00 but nominal bore 75mm

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal of nominal bore 110mm complete all as specified and directed

All as per above item No 108.00 but nominal bore 75mm

S&F in repair PVC (SWR) pipes single socketed in any length with necessary joints laid in trenches of nominal bore 150mm including excavation and dismantling of old pipe complete all as specified and directed

S&F in repair PVC (SWR) bends any radius laid in trenches of nominal bore 150mm complete all as specified and directed

Demolition/breaking up drain pipes (salt glazed stone ware) 450mm bore jointed in cement mortar of any description including PCC bed complete all as specified and directed by Engr-in-Charge.

M&L Reinforced concrete pipes, class NP2, laid and jointed complete with collars of nominal dia 150mm, all as specified

M & L for 300 mm dia, Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified & directed by Engr-in-charge.

M&L Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required, for 150mm dia complete all as specified and directed

Demolition of brickwork or stone/boulders/block masonry, built in cement mortar including all quoins, arches, pillars, ashlar facing, dressed stonework, precast concrete artilcles and precast concrete block walling etc. Complete all as specified and directed.

M&L Squared rubble walling with Porbandar stone masonary in CM 1:6 brought to courses, complete all as specified & directed by Engr-in-charge.

Ditto as above item No. 117.00 but except stone, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting or polycarbonate sheet, any gauge, thickness, in roof covering, cladding complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M & L for 50mm thick Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in plinth protection,Floor topping etc , surfaces finished of concrete flooring with brooming complete all as spd u including provision of necessary construction joints filled with bitumen filler etc complete all as directed by Engr-in-Charge

M&L cement concrete 1:4 :8 type D-2 (40mm graded agg) in foundation filling and mass concrete.complete all as specifed and as directed by Engineer in Charge.

M & L for 100 mm thick cement concrete type B-2 (1:2:4) mix using 20 mm graded stone aggregate as in hard standing

M&L PCC 1:3:6 type C-2 for 150 mm dia pipe bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested, including filling complete all as specified and directed.

M&L for PCC Type D2 1:4:8 (40 mm graded aggregate) in posts all as specified & directed by Engr-in-charge.

M&L for PCC Type B0 1:2:4 (12.5 mm graded aggregate) in coping all as specified & directed by Engr-in-charge.

M&L for plain cement concrete 1:3:6 type C2 (using 40mm graded aggregate bed to drain pipes including packing under and haunching against the sides of pipes of 300mm bore after they are laid and tested complete all as specified and directed by Engr-in-Charge.

M&L for Sand filling under paver blocks for cushion complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement pigment to match, Complete all as specified and directed.

All as per above Except Interlocking tiles including filling with sand cushioning (where ever required) including levelled with Existing tiled surfaces Complete all as spd and directed by Engineer in Charge. (Note :- Sand and PCC shall be paid and measured Separtely).

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement pigment to match, Complete all as specified and directed.

All as per above Except Interlocking tiles including filling with sand cushioning (where ever required) including levelled with Existing tiled surfaces Complete all as spd and directed by Engineer in Charge. (Note :- Sand and PCC shall be paid and measured Separtely).

Surface excavation n.exc 300 mm deep (averaging 150mm deep) and getting out in hard/dense soil.complete all as specified and directed by Engineer in Charge.

M&L for soft soil earth (Black soil) brought from outside MD land to a uniform thickness including watering,spreading and levelling complete all as directed.

Supply, mix and lay farm yard manure for proper plantation complete all as specified and directed

M & L for growing of hedges in the perimeter in size 300mm width and 300mm height with DURANTA or any other approved sampling by GE which gives a thick and dense appearance including cutting and shaping complete all as directed.

M & L for planting of trees ornamental,exotic plants and other approved plants as approved by the GE including watering, shaping including excavation in pits etc. complete all as directed by GE.

S & F water sprinklers of brass rotating type standard quality suitable for 15 / 16 mm dia GI pipe complete all as specified and directed by Engineer in Charge.

Dismantling of post and struts (wood,steel or RCC) any section embedded in concrete, masonry etc including taking out embedded portion and making good disturbed ground.

Dismantling framed trusses of span n exe 10m complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,in hard/dense soil including removing & disposal of soil outside MoD land all as specified & directed by Engr-in-charge.

S&F anodised aluminium snap grid frame work for false ceiling all as specified complete all as specified & directed by Engr-in-charge.

S&F PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing

M&L for providing stainless steel letters of one feet height in English font including fixing charges etc complete in all aspects and as directed by Engr-in-charge.

M&L for providing stainless steel letters of one feet height in Devanagari Hindi font including fixing charges etc complete in all aspects and as directed by Engr-in-charge.

M&L for providing stainless steel letters logo of size 45cm x 45cm including colouring and writing of English / Hindi letters through cutting and engraving by machine including fixing charges complete in all aspects and as directed by Engr-in-charge.

S&F FRP strip cast Iron Park bench fancy type in curved design with backrest and Arm rest of 3 seater capacity complete in all aspects and as directed by Engr-in-charge.

Scarifying the damaged road surface by mechanical means of gravelled macadam or bituminous macadam surfaces in area exc 400 Sqm & deep exc 75mm and n.exc 150mm including stacking the stone in side of road and removing of unwanted material outside complete all as specified and directed by Engr-in-Charge.

Repair to pot holes any depth , not exc 1 sqm each including sweeping free from dust and mud, or water , scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by applying tack coat with bituminous emulsion SS-1 @ 5kg/10 sqm, putting in premixed bituminous macadam (minimum binder content of 4% by weight of total mix as per design mix) well rammed and sealed with binder 9.80 kg/10 sqm, blinded with 0.09 cum of stone chippings, 6.30mm size and again well rammed (including supply & laying premixed macadam binder and chippings), depth of pot holes n exc 30 mm complete all as per IRC specifications complete all as specified and directed by Engr-in-Charge.

M & L for development of lawn area and planting of carpet grass or any other approved grass as approved by GE including watering shaping etc. complete.

S&F 15mm bore medium grade galvanised iron tube , with all type fittingsand accessories laid in trenches complete all as specified and directed by Engineer in Charge.

All as per item No 151.00 above but 25mm bore.

S & F glove or gate valve 15mm bore gun metal, with iron wheel head ,screwed both ends for iron pipe complete all as specified and directed by Engineer in Charge. .

All as per item No 153.00 above but 25mm bore.

Supply only 15 mm bore low density polythylene (LDPE) pipes of pressure rating 6 Kgf/Sq.cm complete all as specified and directed by Engineer in Charge.

Removing Excavated soil exceeding 250 M and n.exc. 500 M and depositing where directed by Engineer -in- Charge.

M&L wooden maple flooring for squash court of standard size including game line marking and dismantling / removal of existing flooring etc complete all as specified and directed

M&L for Anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors

M&L for Anti termite treatment along the external perimeter of the building below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed

Providing and applying of silicon sealent in construction joint, window glass,polycarbonate sheets and required places to make joints water tights, after racking out of joints/cracks wherever necessary & throughtout cleaning at different level complete all as specified and as directed by Engineer-In-Charge.

S&F 12 mm thick toughened glass for door, partition etc. of any size and side portions of toughened glass fixed to wall / floor, joints sealed with clear silicon silicate gel to make water tight, edges with diamond cut including taper drilling to flush the screws / all fitting as required, floor hinges, patch fitting top, bottom and sides, lock and handles, spider joint etc. and floor door spring as per requirement all as specified, required at site by manufacturer instructions and complete all as specified and directed.

S&F ball valves, high pressure of PTMT with epoxy coated aluminium long rod & highdensity plastic big ball screwed for iron pipe including necessary extension nipple and tank nipple suitable for HDPE water tank with check nut complete and fixed of the following size as in repair :-

15 mm bore

20 mm bore

25 mm bore

Taking down old point wiring complete for (light, fan, socket 5/15 amps, bell point etc ) complete with all light fittings accessories , such as switches,sockets 5/15 Amps, ceiling roses, pendents, regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of walls, floors, etc all as speified and directed by Engineer -In-Charge.

M& L for point wiring with PVC insulated unsheathed stranded copper conductor cable FRLSH of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width/in concealed conduit non metallic , rigid PVC conduit of adequated size with all fittings and conduit accessories including suiitable size modular metal flush box and modular white cover plate with frame for housing the switches,socket outlets ,including all necessary wall cutting and making good disturbed surface all as directed and specified .Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

One light point controlled by one, one way switch

One ceiling /exhaust fan point controlled by one switch and regulator

One bell/buzzer point controlled by one bell push.

ditto all as per item No 164.00 but wire 2.5 sqmm One 3 pin 5 amp socket out point on the independent board

ditto all as per item No 164.00 but wire 2.5 sqmm One 3 pin 5 amps socket out let point on same board with other switches.

All as per same in item No 164.00 above but for one socket outlet 15 amp on independent board with 4.0 Sqmm cable and 4.0 Sqmm earth wire.

M& L for point wiring with PVC insulated unsheathed stranded copper conductor cable FRLSH of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including in concealed conduit non metallic , rigid PVC conduit of adequated size with all fittings and conduit accessories including suiitable size modular metal flush box and modular white cover plate with frame for housing the switches,socket outlets ,including all necessary wall cutting and making good disturbed surface all as directed and specified .Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

One light point controlled by one, one way switch

One ceiling /exhaust fan point controlled by one switch and regulator

ditto all as per item No 168.00 but wire 2.5 sqmm One 3 pin 5 amp socket out point on the independent board

ditto all as per item No 168.00 but wire 2.5 sqmm One 3 pin 5 amps socket out let point on same board with other switches.

All as per same in item No 168.00 above but for one socket outlet 15 amp on independent board with 4.0 Sqmm cable and 4.0 Sqmm earth wire.

S & F in replacement of in replacement of Modular switch 1 way 6A, 1 module all as specified and directed by EIC.

S & F in replacement of Modular socket, Socket, 6A - 2/3 pin combined 2 module all as specified and directed by EIC.

S & F in replacement of Modular switch 1 way 16A, 1 module all as specified and directed by EIC.

S & F in replacement of Modular socket 16A - 2/3 pin combined 2 module, all as specified and directed by EIC.

S & F in replacement of Modular fan regulator 120 Watt, 2- module , AC 240 Volts complete.

S & F in replacement of Modular Bell push 6A 1 module all as specified and directed by EIC.

S & F in replacement earth enclosure with 2 pin earth plug sokcet complete with MCB SP 25 amp, flush mounting type all as specified and directed by EIC.

S & F in replacement Call bell AC-230 Volt single pole ding dong

S & F in replacement Ceiling rose, surface bakelite 65x50 mm three terminal

Taking down fan of any make/type/sweep,sealing cable end ,dismantling of blades and for repair /overhauling complete all as directed

M &L for Overhauling of ceiling fan /wall fan of any make and sweep after opening and cleaning rotor bearing and stator properly and oiling/greasing of bearing/ bushes, reassmbling the same, and testing on completion all as specified and as directed

Fixing or hanging only ceiling fan after overhauling/repair of winding above and connecting up including provision of 3 core 1.5 Sqmm cable from ceiling rose or connector to fan( max up to 1m length) all as specified and directed

S & F in replacement LED tube light fittings 4 feet 1x20 Watt ,220V, AC decorative box type with driver,4 V Surge protetction & High Voltage protection upto 440 V ,holder including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge.

S & F in replacement LED tube light fittings mirror type with high output diffuser 2 feet ,1x10 Watt ,220V, AC decorative box type with driver,holder including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge.

S & F in replacement of decorative wall light , gold finish fixture with white glass diffuser suitable for 7.5 W led filament lamp E27 base including its lamp & connecting up with flexible copper conductor cable with suItable size complete all as directed by Engr-In-Charge. Make:-Havells Cat Part No (LHIFOAID1TZ1IO4O)/equivalent in wipro/bajaj

S & F in replacement of LED down light 1x15 Watt 220V, Slim, compact, aluminum die cast edge lit panel. recess/surface mounted square fixture with opal diffuser and separate electronic driver connecting up with 3 core flexible copper conductor cable with sutable size from ceiling rose /junction complete all as directed by Engr-In-Charge.

S& F in replacement of LED Bollard light 10W inverted Pyramid Tripod Type LED Bollard with soft 360 degree distribution with neceesary mounting foundation and connecting with flxible copper cable of suitable size complete all as directed by Engr-In Charge

S& F in replacement of Highbay 150Watt luminaire with pressure die-cast housing, integrated PC optics and 150 lm/W e cacy. 4 kV in-built and 10 kV external surge protection. IP66 ingress protection with additional safety chain in all respect all as specified and directed. Make:- Bajaj Cat Part No :-BIHNK 150W WH NB PC SD / equivalent in Wipro,Bajaj

S& F in replacement of Environmental friendly, new generation, energy saving, decorative IP66 LED spike light of 25 Watt using COB LED as light source connecting up with 3 core flexible copper conductor cable with sutable size from ceiling rose /junction complete all as directed by Engr-In-Charge. Make:- Havells Cat Part No LYCUSSPS25WLED730PSYMBOTG / equivalent in Wipro/Bajaj

S & F in replacement LED tube light fittings 4 feet 1x20 Watt ,220V, AC Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge. cat No. LUMILINENEOBS20WLED840SPCWH/ Equivalent in Wipro/Crompton

S & F in replacement LED Next generation, energy saving, environment friendly & robust highbay LED OF 80 Watt with PDC housing suitable for ceiling (Surface/Suspended) mounting with system efficacy upto 150 lm/W including connecting up with 3 core flexible cppper conductor cable with suitable size from ceiling rose and including suitable accesories for mouting chain /bracket complete all as directed by Engr-In-Charge. Make :- Havlells Cat Prat no: SAUCERGENXHBP80WLED757P60DBOLTG/Equivalent in Wipro/Crompton

S & F in replacement LED street light fittings 1x45 Watt , 230V, New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. including suitable size GI bracket of suitable length and clamps, nut ,bolts etc complete all as directed by Engr-In-Charge. Make:- Havells Cat Part No:- ENDURASUNDOWNSL45WLED765PASYBOPC/equivalent in wipro/bajaj

S & F in replacement LED tube light fittings 4 feet 1x25 Watt ,220V, AC Decorative ultra slim polycarbonate LED lighting fixture with high lumen output, environmental friendly, energy efficient including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge.

S & F in replacement LED street light fittings 1x25 Watt , 230V, AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, surge protector with intact and corrosion resistant including thermal management in muliple optics complete with IP65/66 protection including suitable size GI bracket of suitable length and clamps, nut ,bolts etc complete all as directed by Engr-In-Charge. Make:- Crompton Cat Part No:- LSTS-25 -CDL-M/equivalent in wipro/bajaj

S & F in replacement of LED indoor Wall light 3W, Aluminium, White, 220-240 V , wall mounted for study purpose complete all as directed by Engr-In-Charge.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

S & F in replacement Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable FRLSH 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC CASING CAPING/PVC Conduit not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge.Notes:- (i)Two wires of 6 sqmm and one wire of 6.0 sqmm and one run of PVC casing caping/Conduit shall be measured as one unit.

Dismantling unserviceable main switch/ kitkat DBs/ MCB including wooden board from existing position and making good disturbed surfaces of wall to match with existing surfaces

S & F in replacement MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, earth bar and Din rail ,240Volts SPN with 8 way Double door , IP-43-IK09 protection

S & F in replacement MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 40 to 63Amps

S & F in replacement MCB SP 240 Volts 'C' series, breaking capacity 10 KA of rating 6-32 Amps

M& L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly including chemical powder for earhing and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with using galvanised iron 32×6mm strip as eartlung lead all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion

M& L Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion all as specified and indicated including testing on completion.

M & L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing strip of 4mm x 25 mm dia galvanised iron or steel strip all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion

Supply & fix in replacement of PVC insulated 3 core 1.5 sqmm multistranded Copper conductor as specified & directed. Make:- Polycab/Havells/Gloster

Supply and fix in replacement of PVC pipe 25 mm dia heavy duty inclusive of all tees,bends, elbows etc & fixing accessories

S & F in replacement MCB DB SPN 2 way Double door made of sheet steel, powder painted with bus bar, neutral link, earth bar and Din rail , 240Volts Inclding with MCB SPN 32 Amps as specified & directed.

S & F in replacement MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade , 415Volts TPN with 4 way Double door

S & F in replacement MCB TPN 415 Volts, 'C' series, breaking capacity 10 KA of rating 40 to 63Amps

S & F in replacement MCCB DB VERTCLE TYPE made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade ,Glazed door 415 Volts TPN with 6 way Double door

NOTE FOR ITEM NO 211.00 : (1).The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall./ DB to be fixed on wall (2).The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface. (note - rate is inclusive of cutting chaseS & F in replacementin repair lush to wall & making good to the disturbed surfaces of walls etc to macth with existing surfaces including white washing/colour washing/distempering to match with existing wall/floor/ceiling finishes making good disturbed surfaces of walls, etc )

S & F in replacement MCCB TPN 100 Amps , 415Volts, 16 KA

Taking down unservisable U/G cable from trenches, wall, floor etc upto 25 sqmm

S& F XLPE insulated armoured and pvc sheated heavy duty electric cable ,3.5 core 25 Sqmm cross sectional area aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete for following size Note- rate is inclusive of cable gland & cable lugs

Excavation in trenches in hard /dense soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cables, RCC poles/stays and struts etc and getting out including trimming sides and forming bottom surface all as specified and directed at site.

Returning, filling in including spreading, leveling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays , struts have been erected and tested , all as specified and directed at site

Removing excavated surplus soil (Soft/hard soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

S& F in replacement of laying of Double Walled Corrugated (DWC) HDPE pipe 50/38 mm outer/inner dia size of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge Make:-ASTRAL TELEREX /eqivalent as approved by GE

Supply, install, testing &commissioning hi wall split unit air conditioners inverter type indoor/outdoor complete including outdoor unit mounting stand , electric driven single phase, copper tube condensor coil, cordless remote control of capacity of 2.0 TR BEE 5 star rated complete all as specified and directed.

Supply and fix PVC pipe 20 mm dia heavy duty inclusive of all tees,bends, elbows etc & fixing accessories for drain out condensing water of split AC including cutting of floor/opening of hole in wall and making good after laying of pipe etc to match the existing surface complete.

S & f sub main wiring of size 4 sq mm 2 core (FRLS) along with earth wire of 4 sq mm single core of FRLS PVC insulated unsheathed cable, 1100 volts grade with multistranded copper conductor including PVC casing caping /Conduit of suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fix voltage stabilizer single phase 50 cycles AC supply designed for input voltage of 170 V to 250V and out put voltage stablised between 215V to 240V of capacity 5 KVA including necessary mounting arrngement complete all as specified & directed by Engr-In-Charge..MAKE V-GUARD MODEL VG 500

Vastushilp Building Designer (BID ID -3156444)

VIVEK JITENDRABHAI KATAR (BID ID -3157310)

nidhi construction co. (BID ID -3157889)

RUDRAAY CONSTRUCTION (BID ID -3154313)

K K Construction Co (BID ID -3157716)

Harsh Infrastructure (BID ID -3157843)

OM ENTERPRISE (BID ID -3157789)

shree chamunda enterprise (BID ID -3157968)

M/S. P.M GODHANIYA (BID ID -3157447)