U/g Kangra to Ghalain Via Rajal Bohar Kawaloo road km. 0/0 to 30/850 Packgae No. HP-04-411

Amount

Excavation in hilly area in all heights and depths and in all kind of soil by all means including saturated soil comprising of ordinary soil, soft rock, hard rock, chiseling wedging out of rock (where blasting is prohibited) and their intermediate classification of soil complete including setting out true to the required lines, grades, width cutting and trimming of side slopes and level as shown in the drawing and as directed by Engineer-in-Charge at site according to the MORD technical specification section 300 and 1600 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of road and transporation of surplus material for filling in road ways, camber, embankments for grade improvements and disposal of all unuseful material to the approved dumping sites through all modes of transportations including head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and other incidentals, necessary to complete the work by mechanical means and/labour if required. Recovery for useful stone to the tune of 2836.96 Cubic metre quantity at the rate of Rs.300/-(Rupees Three hundred) only per cubic metre shall be effected from the contractor running bills on pro-rata basis as per actual quantity executed. Any loss to the public, private property during the course of execution shall be the absolute responsibility of the contractor which shall heve to be compensated by him in all cases. The rate is including octroi, royality, malkana, toll tax or other taxes imposed by the Government excluding GST.

Loosening of the ground upto the level of 300mm (Three hundred milimetre) below the sub grade level, watered, graded with motor grader and compacted in layers to meet requirement of Table 300.1 and 300.2 with three wheel 80-100 (eighty to hundred) kN static roller for sub grade construction as per MORD technical specification section 300 and as per the direction of Engineer-in-Charge including cairrage of materials within all leads, lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, or other taxes imposed by the Government excluding GST.

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading by mechanical means to required slope and compacted with three wheel 80-100 (eighty - hundred) kN static roller to meet requirement of Table 300.2 complete as per MORD technical Specification Section 400 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.. The rate is including octroi, royality, Malkana, toll tax, or other taxes imposed by the Government excluding GST.

Earth work in excavaxtion for all type of road structure such as retaining walls, breast walls, culverts, drains and parapets etcetera in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock, chiseling/ weding out rocks (where blasting is prohibited) as per drawings and MORD technical specification section 300 and 1600 and as per direction of the Engineer-in-Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides, bottom and back filling in trenches with excavagted suitable approved material to the original surface in layers not exceeding 150mm (One hundred fifty milimetres) compacted thickness including shoring, strutting, pumping and bailing out water (surface and sub soil water) upto any depth and any quantam of water including cleaning of slush which any arrise out during dewatering as per direction of the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including the octroi, royality, Malkana, toll tax or any other taxes imposed by the Govefrnment excluding GST.

Back filling with granular material behind abutments, return walls, wing walls, retaining walls etcetera complete as per drawing and M.O.R.D. technical specification section 1200 and 1600 or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate includes octroi, royality, Malkana, toll tax, or other taxes imposed by the Government excluding GST.

Construction of grannular sub base by providing well graded materials spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method at OMC with tractor mount appropriate ratotavator attachment and compacting with three Wheel 80-100 (Eighty-hundred) kN static roller to achieve the desired density, complete as per M.O.R.D. Technical Specification Clause 401 for grading-I material or as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing, laying, spreading and compacting by mechanical means 75mm (Seventy five milimetre) compacted thickness broken/crushed stone aggregate of Grading-II 63mm to 45mm (sixty three milimetre to forty five milimetre) nominal size to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 K.N. static roller in stages to proper grade and camber, applying and brooming, with application of stone screening type-B of size 11.2mm (Eleven point Two milimetre) nominal size @ 0.20 (Zero point two zero) cubic metre per 10 sqm. (Ten square metre) and binding material @ 0.06 (Zero point zero six) cubic metre) per ten square metre to fill up the interstices of course aggregate, watering and compacting to required density as per MORD Technical specification clause 405 including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing, laying, spreading and compacting by mechanical means 75mm (Seventy five milimetre) compacted thickness broken/crushed stone aggregate of Grading-III 53mm to 22.4 mm (fifty three milimetre to twenty two point four milimetre) nominal size to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 K.N. static roller in stages to proper grade and camber, applying and brooming, stone screening type-B of size 11.2mm (Eleven point two milimetre) nominal size @ 0.18 (Zero point one eight ) cubic metre per 10 sqm. (Ten square metre) and to fill up the interstices of course aggregate watering and compacting to required density as per MORD Technical specification clause 405 including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and applying primer coat with BITUMEN emulsion (SS-I) with Silance nanotechnology (Tera Primer) @ 1% by weight of emulsion on the prepared surface of granular base including cleaning of road surface with Hydraulic brooms and spraying primer @ 0.85 Kg. (Zero point eight five kilogrammes) per square metre using mechanical means as per M.O.R.D. technical specifications clause No.502 including hauling of material in all leads, lifts as per the entire satisfaction and direction of Engineer-in-Chargte including carriage of materials within all leads and lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and applying tack coat with BITUMEN emulsion (RS-I) with Silance nanotechnology (Nano Tac) 1.4% by weight of emiulsion using emulsion distributor at the rate of 0.250 Kgs. (Zero decimaltwo five zero kilogrammes) per square metre on the prepared granular surface treated with primer and cleaned with hydrfaulic broom as per technical specification clause 503 including hauling of magterial in all leads, lifts as per entire satisfaction and direction of Engineer-in-Chargte including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and applying tack coat with BITUMEN emulsion (RS-I) with Silance nanotechnology (Nano Tac) 1.4% by weight of emulsion using emulsion distributor at the rate of 0.250 Kgs. (Zero decimal two five zero kilogrammes per square metre on the prepared bituminous surfaces cleaned with hydraulic broom as per technical specifications clause 503, includign hauling of material in all leads, lifts as per entire satisfaction and direction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying 50mm (Fifty millimetres) compacted thick bituminous macadam with 100-120 (One hundred -One hundred twenty) tonne per hour hot mix plant producing an average output of 75 tonnes (seventy five tonne) per hour using crushed aggregates of specified grading as per table 500.4 premixed with bituminous binder VG-10 (Viscosity Grade-Ten) with Silance nanotechnology (Zyco therm) @ 0.1% by weight of Asphalt binder using bitumen, at the rate of 3.3% (Three decimal three percent) of mix weight transported to site, laid with paver finisher hydraulic sensor control to required grade level and alignment over a previously prepared surface and rolling complete with smooth wheeled roller 8 to 10 (Eight to Ten) tonne capacity for initial break down rolling and vibratory roller 8 to 10 (Eight to Ten) tonne for intermediate rolling and finish rolling with 6 to 8 (Six to Eight) tonne smooth wheeled tandem roller to achieve the desired compaction as per MORD technical specifications 504 including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer-in-Charge. The rate including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying 30mm (Thirty millimetres) compacted thick bituminous concrete with 100-120 (One hundred -One hundred twenty) tonne per hour hot mix plant producing an average output of 75 tonnes (seventy five tonne) per hour using crushed aggregates of specified grading as per table 500.4 premixed with bituminous binder VG-10 (Viscosity Grade-Ten) with Silance nanotechnology (Zyco therm) @ 0.1% by weight of Asphalt binder using bitumen, at the rate of 5.5% (Five decimal five percent) of mix and filler weight transported hot mix to work site, laid with paver finisher hydraulic sensor control to required grade level and alignment over a previously prepared surface and rolling complete with smooth wheeled roller 8 to 10 (Eight to Ten) tonne capacity for initial break down rolling and vibratory roller 8 to 10 (Eight to Ten) tonne and tandem roller rolling to achieve the desired compaction as per MORD technical specifications 507 including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Scarifying the existing bituminous road surface to the depth of 150mm (One hundred fifty milimetre) and disposal of scarified material within all lead, lift and as per MORD technical specification clause 301.4 as per direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design and laid over a prepared sub base, M-30 Grade Design Mix concrete made with 43 grade cement having content not less than 430 kg (four hundred thirty kg) per cubilc metre, coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm (Twenty five milimetre), mixed in a concrete mixer with appropriate weigh batcher, laid in approved fixed side form work (steel channel) including providing, and laying and fixing of 125 micron (One hundred twenty five micron) thick polythene film, over base, compaction of concrete with vibrators and compactors, water curing and using curing compound (where required) , providing and fixing of debounding strips dowel bars, primer and sealant at construction joints and joints with bridges and culverts structures as per M.O.R.D. technical specificatgion clause 1501 including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying of cold plastic road marking paint of approved manufacture 2.5mm (Two decimal five milimetre) thick with reflectorising glass beeds at the rate 250 (Two hundred fifty) gram per square metre area, thickness of 2.5mm is exclusive of surface applied glass beeds as per specification and with strips of 0.10 (zero decimal one) metre width in centre lines or edge lines of the road as per the directions of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals.. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm (Eighty milimetre) as per drawings and Technical Specification Section 1500, as per direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete for nominal mix 1: 4: 8 (one cement: four sand : Eight graded crushed stone aggregate 40mm (forty milimetres) nominal size including pumping or bailing out water / dewatering, cost of form work curing complete in all type of structure like retaining walls, breast walls etcetera as per drawing and MORD technical Speficiations section 800,900 and 1200 including carriage of material with in all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying 100mm (Hundred milimetre) diametre PV.C. pipe weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall and retaining/breast walls etc. extending through the full width of the structures with slope of 1(V): 20(H) (One vertical isto Twenty horizental) towards draining face complete as per drawing and M.O.R.D. technical specifications clause/ section 700 and 1200 including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Stone soling properly hand-packed filling interstices with Kharanja stone and consolidating with power road roller to the requested gradient and comber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour), as per direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in open foundation for all type of structure complete using plain cement concrete grade M-10 ( M Ten) nominal mix 1: 3: 6 (One cement : Three sand : Six graded crushed/broken stone aggregate 20mm (twenty millimeter) nominal size) on ground or under water and curing complete including pumping or bailing out water , dewatering removal of slush as required at site which may arrise at the time of laying concrete complete for all heights/ depths including the cost of form work as per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete grade M-15 (M-fifteen) design mix having cement contents not less than 275kg (two hundred seventy five kilogram per cubic metre) on ground or under water including curing complete pumping or bailing out water de-watering removal of slush as required at site, which may arises at the time of laying concrete complete for all heights/depths including cost of form work in Sub Structure i.e. abutment, toe wall etcetra as per drawing and MORD technical specification section 800, 900 and 1200 including carriage of materials in all leads, lifts and other incidental, as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated cement concrete blocks flooring including bedding nominal mix 1:2 1/2:5 (One cement: Two & half sand: five graded crushed/ broken stone aggregate 40mm (forty milimetre) nominal size) in all heights/depths on ground or under water including pumping or bailing out water/dewatering (surface and sub soil water) and removal of the slush which may arise at the time of laying concrete complete for all heights/depths and any quantum of water, including cost of form work and curing complete in flooring etcetera complete as per drawing and MORD Technical specification clause 1303 as per the directions of Engineer-in-Charge including carriage of material in all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Filling in foundation trenches as per drawing and M.O.R.D. technical specifications clause 305.3.9 earth filling and as per direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying (to level or slope) 300mm dia (Three hundred millimeters) diametre reinforced cement concrete heavy duty non pressure pipes IS Class NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1 : 2 ( One cement : two sand) but excluding the cost of excavation, protection works, back filling, bedding concrete and masonry work in head walls and parapets as per drawing and M.O.R.D. technical specifications clause 1101 and as per direction of Engineer – in- Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying of boulder apron laid in wire crates with 4mm (Four milimetre) diametre G.I. wire (Galvanised Iron wire) confirming to IS:280 and IS:4826 in 100mmx100mm (One hundred milimetre into One hundred milimetre) mesh (Wovan diagonally) including 10%(Ten percent) extra for laps and joints laid with stone boulder weighing not less than 40 kg (Forty kilogram) each as per drawing and MORD technical specification clause 1301 and as per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing / errecting a " W" metal beam crash barrier composing of 3 mm (three millimetre) thick corrugated sheet metal beam rail, 70 cm (seventy centimetre) above road/ Grond level fixed on I.S.M.C. series channal vertical post 150 x 75 x 5 mm (one hundred fifty five into seventy five into five millimetre) spacer 2 m (two metre) centre to centre 1.8 m (one point eight metre) high, 1.1 m (one point one metre) below ground/ road level, all steel post and fitments to be galvanised by hot dip process. All fitting to conforms to I.S 1367 and I.S. 1364 metal beam rail to be fixed as the vertical post with spacer of channal section 150x75x5mm (one hundred fifty into seventy five into five millimetre) and 330 mm (one hundred thirty millimetre) long complete as per clouse 811 of MORT&H specification (5th revision) as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Supplying fitting and placing HYSD bar reinforcement (Fe-415) in sub-structure complete as per drawing and M.O.R.D. technical specifications section 1000 and 1200 including cutting, bending, binding and placing in position including cost of binding wire complete in all respect as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Supplying fitting and placing HYSD bar reinforcement (Fe-415) in superstructure complete as per drawing and M.O.R.D. technical specifications clause section 1000 and 1400 including cutting, bending, binding and placing in position including cost of binding wire complete in all respect as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated, reinforced concrete in sub-structure of all type of structure complete using reinforced cement concrete grade M-20 (M-Twenty) design mix having cement contents not less than 330 kg. (Three hundred thirty kilogram) per cubic metre with 20mm (Twenty milimetre) nominal size graded crushed stone aggregate and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in abutment etcetra as per drawing and MORD technical specification section 800, 900 and 1200 and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in open foundation for all type of structure complete, grade M-20 (M-twenty) design mix having cement contents not less than of 330 (Three hundred thirty) kilogram per cuibic metre with 20mm (Twenty milimetre) nominal size graded crushed stone aggregatge and curing complete, for all heights/depths including the cost of form work as per drawings and MORD technical section 800,900 and 1200 and as per the direction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete of Grade M-25 (M-Twenty five) design mix having cement contents not less than of 400 (Four hundred) Kilogram per cubic metre with 20mm (Twenty milimetre) nominal size graded crushed stone aggregate in super-structure as per drawing and MORD technical specification section 800, 900 and 1400 and curing complete including cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab including carriage of material within all leads, lifts and other incidental as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including of octori, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and fixing of typical PMGSY informatory sign board with logo as per M.O.R.D. specification and drawing . Three MS plates of 1.6 mm ( one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres into five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetre into twenty five milimetres into five millimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre into seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetre into forty seven millimetres) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and M.O.R.D. technical specifications section 1700 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade 5th (fifth) Kilometre stone (Precast) of standard design as per IRC :8 (eight) fixing in position including painting and printing etcetera as per drawing and MORD technical specification clause 1703 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads and lifts and other incidentals, labour and equipment required to execute the work to the site of work complete in all respect. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade Ordinary Kilometer Stone (Precast) of standard design as per IRC :8 (eight) fixing in position including painting and printing etcetera as per drawing and MORD technical specification clause 1703 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads and lifts and other incidentals, labour and equipment required to execute the work to the site of work complete in all respect. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade 200m (two hundred metre) Stone (Precast) of standard design as per IRC :8 (eight) fixing in position including painting and printing etcetera as per drawing and technical specification clause 1703 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads and lifts and other incidentals, labour and equipment required to execute the work to the site of work complete in all respect. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600mm (six hundred millimetre) equilateral triangle as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per section 1700 of MORD specifications for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and MORD Technical Specification section 1700 including painting angle iron post with primer and two post of Epoxy paint as per specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600mm (six hundred millimetre) Circular as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in fornt and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per section 1700 of MORD specifications for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and MORD Technical Specification section 1700 including painting angle iron post with primer and two post of Epoxy paint as per specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and erecting direction and place identification semi-reflective sign boards upto 0.90 sqm (zero point nine zero) size board, as per IRC-67 made of 2.0mm (two point zero millimeter) thick MS sheets duly stove enamelled paint in white colour in front and gray colour on back with red reflective border of 70mm (seventy millimetre) width and required message, letters and figures with reflective tape engineering grade as per section 1700 of MORD specifications for rural roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG (forty seven into forty seven millimetre of tewlve standard wire gauge) sheet square tube of 3050mm (three thousand fifty millimetre) height duly strengthened by 25mm x 5mm (twenty five millimetre into five millimetre) mild steel flat iron on edges on back firmly fixed to the ground by mean of properly designed foudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeter) , 600mm ( six hundred millimeter) below ground level as per approved drawings and MORD technical specification section 1700, including painting angle iron post with primer and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and erecting direction and place identification semi-reflective sign boards upto 0.90 sqm (zero point nine zero) size board, as per IRC-67 made of 2.0mm (two point zero millimeter) thick MS sheets duly stove enamelled paint in white colour in front and gray colour on back with red reflective border of 70mm (seventy millimetre) width and required message, letters and figures with reflective tape engineering grade as per section 1700 of MORD specifications for rural roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG (forty seven into forty seven millimetre of tewlve standard wire gauge) sheet square tube of 3050mm (three thousand fifty millimetre) height duly strengthened by 25mm x 5mm (twenty five millimetre into five millimetre) mild steel flat iron on edges on back firmly fixed to the ground by mean of properly designed foudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeter) , 600mm ( six hundred millimeter) below ground level as per approved drawings and MORD technical specification section 1700 (Maintenance Board), including painting angle iron post with primer and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Guard stones on curves made of reinforced/ local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and MORD technical specification Clause 1704 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and Fixing pavement marker (Cat eyes) made out of ABC 3 M (three) plastic of size 128x110x29.5 mm (one hundred twenty eight into one hundred ten into twenty nine decimal five millimetres) without nail having 50mm ( fifty millimetres) stem of ABS. The pavement marker shall be installed with epoxy ABS including carriage of materials and equipment with all mode of transportation and as per direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Providing and fixing road side delineator of height 600mm made of MS pipe of size 50mm of 1.6 SWG having High intensity micro prismatic reflective sheeting confirming to ASTM type-XI upto 300mm length Balance 300mm It shall be painted with synthetic enamel paint of alternate colour black & white strips. It shall be fixed with 30 x 30 x 30cm block with cement concrete 1:2:4 (1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size complete in all respect The work shall be executed as per the direction of the Engineer- In-charge including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Collection of hardwood cuttings from appropriate approved species, from sources within all leads of the road, including trimming the sterms and making the cuttings, and transporting while wrapped in damp material as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Planting unrooted hardwood cuttings (2.0 m in length and 3.0 to 8.0 cm in diameter) of appropriate approved species on slopes, including final preparation of cuttings, preparing lines, digging trenches to specified dimensions and forming fascines as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Road side tree planting containerzed tree and shurbs including potting, transplanting, compacting and mulching on slopes 30 degree to 60 degree pits size 30 cm diametre into 30cm depth. Providing and mixing compost with thre soil, Provisioning and applying of pesticides of required including labour and transporation to the site as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and MORD Technical Specification clause 1702 including hauling of material in all kinds of leads, lifts and other incidental as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including of octori, royality, Malkana, toll tax or other taxes imposed by the Government excluding GST.

Routine maintenance works for five years

For 1st Year

For 2nd Year

For 3rd Year

For 4th Year

For 5th Year

MCC POWER PROJECT PVT. LTD.

Navneet Thakur

V P Sharma