SPECIAL REPAIR TO CERTAIN BUILDINGS AT HAWS UNDER GE 969 EWS.

Amount

Demolition cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above grond level) complete all as specified and directed by engineer-in-charge.

Dismantling floor hearh, wall tiles incl cement mortar bedding, removing serviceable tiles to store and rubbish of the permishes complete all as specified and directed by engineer-in-charge.

Taking down plastering on lathing (other than wire-netting), without removing lathing, in cement lime or cement mortar complete all as specified and directed by engineer-in-charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by engineer-in-charge.

Dismantling of wall and celling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness inlcuding cover fillets complete all as specified and directed by engineer-in-charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by engineer-in-charge.

Dismantling timber scantlings 40 sqcm and over in section in any position unframed work complete all as specified and directed by engineer-in-charge.

Taking down chowkats or frames but with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm and not exceeding 4.00 sqm complete all as specified and directed by engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding1.5 Sqm complete all as specified and directed by engineer-in-charge.

Demolition of brick work, PCC block masonary, stone masonary or boulder masonry built in cement mortar complete all as specified and directed by engineer-in-charge.

M&L 40 mm thickness Cement concrete type B-1, 1:2:4 (20mm graded aggregate) complete all as specified and directed by engineer-in-charge.

M&L Cement concrete 75 mm thik type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection finished even and smooth complete all as specified and directed by engineer-in-charge.

M & L Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. Incl screed bed 15 mm thick in CM (1:6)complete all as specified and directed by engineer-in-charge.

All as per item no-13 but as in skirting complete all as specified and directed by engineer-in-charge.

M&L Glazed ceramic tiles in vertical surface 600 x300 x10 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including screed bed 10 mm thickness in CM (1:4) complete all as specified and directed by engineer-in-charge.

M&L Non - skid Ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match Incl screed bed 15 mm thick in CM (1:6) complete all as specified and directed by engineer-in-charge.

M&L Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed by engineer-in-charge.

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 complete all as specified and directed by engineer-in-charge.

Raised pointing to random or polygonal rubble, uncoursedor brought upto courses cement mortar 1:4 complete all as specified and directed by engineer-in-charge.

M&L for preparation of new surfaces of walls and applying two coats of Oil bound distemper over a coat of priming on plastered and other surfaces with alkali resistant priming paint complete all as specified as directed by engr-in-charge.

M&L for preparation of old surfaces of walls and applying two coats of Oil bound distemper complete all as specified as directed by engr-in-charge.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer-in-charge.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; complete all as specified and directed by engineer-in-charge.

M&L 4 mm thick veneered decorative plywood,grade 1 (with BWR resin) with decorative face veneers on both faces,in wall fixed with screws to timber frame work complete all as specified and directed by engineer-in-charge.

M&L plain fillets square rectangular or triangular in section using 2nd class soft wood clean swan secured with nails not exc 3 sqcm in section

M&L in repairs plain fillets square rectangular or triangular in section using 2nd class soft wood clean swan secured with nails exc 3 but not exc 6 sqcm in section complete all as specified and directed by engineer-in-charge.

S&F 6 mm thick insulation consisting of PVC Insulated Panels (round moulded) as in wall having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing Note : Panelling should be rested on L/U shape edge profile of same pattern of panelling (PVC/Aluminium)

S&F 6 mm thick insulation consisting of PVC Insulated Panels (round moulded) as in ceiling having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing Note : Panelling should be rested on L/U shape edge profile of same pattern of panelling (PVC/Aluminium)

S&F Aluminium anodised angle/tee 40x40x5 mm as in ceiling frame work/grid of size 605x605mm complete all as specified and directed by engineer-in-charge.

S&F 2nd class soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by engineer-in-charge.

M&L Glazed and skeleton shutters thickness 30 mm,(2nd class softwood), open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters supplied and fitted to chowkats if windows, ventilators, etc. are provided with stiles and rails as in SSR Part I, Sectionspecified 8 clause 8.24(a) complete all as specified and directed by engineer-in-charge.

M&L for Glazed and skeleton shutters thickness 30 mm,(2nd class softwood), open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters supplied and fitted to chowkats if windows, ventilators, etc. are provided with stiles and rails as in SSR Part I, Sectionspecified 8 clause 8.24(b) complete all as specified and directed by engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by engineer-in-charge.

S&F Sheet glass thickness 4.00 mm,ordinary quality and glazing with oil putty in square exceed 0.5 sqm in each pane

S&F Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by engineer-in-charge.

M&L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing . & drawing

M&L Preparation of new wooden surface of any description and two coat of synthetic enamel paint over a coat of primer , not otherwise descri-bed,over 10cm width or girth complete all as specified and directed by engineer-in-charge.

M&L Preparation of old wooden surface of any description and two coat of synthetic enamel paint over a coat of primer, not otherwise descri-bed,over 10cm width or girth complete all as specified and directed by engineer-in-charge.

S&F Aluminium anodised, barrel tower bolts 100 mm of extruded section and fixed complete all as specified and directed by engineer-in-charge.

S&F Aluminium anodised, barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed by engineer-in-charge.

S&F Aluminium alloy, anodised, sliding door bolt 200 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by engineer-in-charge.

M S Butt hinges 100 mm medium weight, cold rolled mild steel, and fixed complete all as specified and directed by engineer-in-charge.

M S Butt hinges 75 mm medium weight, cold rolled mild steel, and fixed complete all as specified and directed by engineer-in-charge.

S&F Aluminium handles 100 mm , cast type,anodised complete all as specified and directed by engineer-in-charge.

S&F Aluminium handles 150 mm , cast type,anodised complete all as specified and directed by engineer-in-charge.

S &F in repair stainness steel curtain rod, mild steel, chromium plated fixing with stainless steel brackets and funnels stops, rollers etc 25 mm dia complete all as specified and directed by engineer-in-charge.

S&F in repair IInd class softwood in scantling clean swan timber framed and fixed to the position to replace old and decayed timber complete all as specified and directed by engineer-in-charge.

S & F PVC valveless, syphonic action type, flushing cistern 10 ltrs, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 60 cm long of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed by engineer-in-charge.

S&F in repairs Stop/angle valves 15 mm, cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated complete all as specified and directed by engineer-in-charge.

Taking down and replacement with 25 mm 3-layer PP-R polypropylele random copolymer) concealed pipe SDR 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PRR plain & brass threaded polypropylele random fittings fixed complete to walls, ceiling or in floors , complete all as specified and directed by engineer-in-charge.

Taking down and replacement with 20 mm 3-layer PP-R polypropylele random copolymer) concealed pipe SDR 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PRR plain & brass threaded polypropylele random fittings fixed complete to walls, ceiling or in floors , complete all as specified and directed by engineer-in-charge.

S&F in repairs Bib taps 15 mm bore , cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by engineer-in-charge.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), including pvc seat and cover for pedestal pan white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed by engineer-in-charge.

S&F in repairs CP jet spray with flexible tube 1.5 mtr long complete all as specified and directed by engineer-in-charge.

S&F in repairs CP health fucet hand held triggered nozzle and delivers a spray of water with pipe complete all as specified and directed by engineer-in-charge.

M&L 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by engineer-in-charge.

S&F in repair vitreous chine wash basin, white flat back size 550x400 mm plug, porcelain stopper and incl brackets with waste fittings and connection pipe etc including pedestal complete all as specified and directed by engineer-in-charge.

S&F in repair brass chromium plated tubular towel rail 20 mm dia D type , 60 mm long between flages complete all as specified and directed by engineer-in-charge.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm sheet glass shelf 12 cm wide with brass chromium plated bracket guard and 60 cm long complete all as specified

S&F in repairs corner sheet glass shelf assembly consisting of 5.5 mm sheet glass shelf 12 cm wide with brass chromium plated bracket guard complete all as specified and directed by engineer-in-charge.

S&F in repairs 20 mm Brass CP centre hole basin mixer complete all as specified and directed by engineer-in-charge.

S&F in repair PVC (SWR) pipes 110 mm single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by engineer-in-charge.

S&F in repair PVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by engineer-in-charge.

S&F in repairs Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed by engineer-in-charge.

S&F in repair 8 mm thick wooden floor edges tongued and grooved joint layers complete all as specified and directed by engineer-in-charge.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out complete all as specified and directed by engineer-in-charge.

M&L Cement concretein foundations, filling and mass concrete type C2 1:4:8 ( 40 mm graded aggregate) complete all as specified and directed by engineer-in-charge.

M&L for Pre-cast cement concrete block masonry with solid blocks (vibrator made) Type B1 1:2:4 (20 mm graded aggregate) , exc. 10 cm in width and setting in CM (1:6) , complete all as specified and directed by engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by engineer-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by engineer-in-charge.

M&L Slabs supported on walls B1 1:2:4 (20 mm graded aggregate), beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by engineer-in-charge.

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by engineer-in-charge.

Dismantling water tanks 1000 ltrs capacity and fixing new Rotational moulded polyethylene water storage tanks1000 ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by engineer-in-charge.

S&F in repairs 20 mm Ball brass valves, high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S&F in repairs Stop/angle valves 20 mm, cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated complete all as specified and directed by engineer-in-charge.

M&L Cement concrete 40 mm thick Type B2 1:3:6 (40 mm graded aggregate ) in surface channels and drains complete all as specified and directed by engineer-in-charge.

M&L Providing Coping , cement concrete 40 mm thick type C1 1:3:6 20 mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by engineer-in-charge.

M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited broken stone or boulder, spread and levelled in layers not exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by engineer-in-charge.

S&F Durapaved chequered tiles (vitrified) 30 cm x30 cm x 10 mm thick set ,jointed and pointed in neat cement slurry in floors over 20 mm thick screed bed in CM (1:6) finished with cloured cement to match the shed of the slab complete all as specified and directed by engineer-in-charge.

M & L Walling of random rubble ,uncoursed CM (1:4) as in built complete all as specified and directed by engineer-in-charge.

S&F Softwood 2nd class Clean sawn with butt joints eaves boards 20 mm thick complete all as specified and directed by engineer-in-charge.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W (Gde-E- 250)quality complete all as specified and directed by engineer-in-charge.

S&F Steel work in roof trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S .1161-1979 grade St.-240 complete all as specified and directed by engineer-in-charge.

M&L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by engineer-in-charge.

M&L Creosote preparing surfaces of wood and wood based materials, and wood based materials, new or old, of any description and girth, not otherwise described and treated with complete all as specified and directed by engineer-in-charge.

M&L Weather boarding, 25 mm thick, wrought both sides, V-jointed to give 20mm laps and fixed complete all as specified and directed by engineer-in-charge.

Providing precast cement concrete type C1 1:3:6 (20 mm graded aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses,copings.anchorage blocks, bonders (for stone wallin) and setting in mortar(1:6)complete with joints to match complete all as specified and directed by engineer-in-charge.

M&L for Mild steel bars 6 mm dia and over (TMT bars), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by engineer-in-charge.

E/M WORKS:-Taking down carefully existing copper/aluminium point wiring (light, fan, socket or power) complete including all fixtures (fitting such as switches, ceiling rose, lamp holders, pendents, regulator, switch socket, light fittings etc without disturbing exisiting serviceable points and fittings, keeping in safe custody for reuse at site, making good disturbed surface walls, floors etc all as directed.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes,including modular PVC box,modular white cover plate and inner plate with frame of suitable size for mounting modular switches/sockets,fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified and directed for:- (a) One light point controlled by one single pole one way 5 Amps switch.

(b)All as per srl item No-91above but One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board .

(c)All as per srl item No-91 above but One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

M&L for point wiring in PVC casing caping with 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws guttier/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated fire retardant cable of size 2.5 Sqmm as earth continuity conductorcomplete all as specified and directed by engineer-in-charge.

S&F Modular switch 1 way 6A, 1 module, 240 volts, complete all as specified and as directed by Engineer-in-charge. Note : Taking down of swithches included in taking down point wiring

S&F switch piano Flush type, single pole, one way 6 amp 240 volts, complete all as specified and as directed. Note : Taking down of swithches included in taking down point wiring

S&F Modular Socket outlet, 6A - 2/3 pin combined 2 module. complete all as specified and as directed by Engineer-in-charge. Make : Anchor / Bajaj / Havells or Equivalenta Note : Taking down of socket outlet included in taking down point wiring

S&F Socket outlet 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed by engineer-in-charge.

S&F Modular Switch socket combination 3 pin 5 amp' flush type,universsal complete all as specified and as directed by Engineer-in-charge

S&F in repair Switch socket combination 2 in1, 3 pin,5 Amps flush type,universsal complete all as specified and as directed.

S&F Switch socket Combination 16A, 6 pin, 3 module, 2 in 1, flush type universal complete all as specified and directed by engineer-in-charge.

S&F Switch socket Combination 15A, 3 pin, 2 in 1, flush type universal complete all as specified and directed by engineer-in-charge.

S&F ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body complete all as specified and directed by engineer-in-charge.

S&F in repairs Lamp Holder, PVC/ Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed.

S&F Sheet metal enclosures for DB’s (when MCBs are to be used) Single door, single pole and neutral 12 way, 240 volts with 200 Amp rated bus bar, complete all as specified.

S&F Sheet metal enclosures for DB’s (when MCBs are to be used) Single door, single pole and neutral 08 way, 240 volts with 200 Amp rated bus bar, complete all as specified.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by engineer-in-charge.

S&F MCB 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by engineer-in-charge.

S&F MCB amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB SPN 40 Amp complete with connection testing and commissioning complete all as specified and directed by engineer-in-charge.

S&F amp MCB rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB SPN 63 Amp complete with connection testing and commissioning complete all as specified and directed by engineer-in-charge.

S&F LED Lamp 15 W complete all as specified and directed by engineer-in-charge.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-charge.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose. complete all as specified and directed by engineer-in-charge.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Comlpete all as specified and directed by Engineer-in-charge.

S&F Exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers. Complete all as specified and directed by Engineer-in-charge.

M&L for Sub main wiring with 2 runs of 6 sqmm PVC insulated multi stranded FRLS copper cable drawn through PVC casing capping of required size with accessories along with 1 run of 6 sqmm copper cable as earth continuity conductor including taking down the old existing submain wiring complete all as specified and as directed. Note :- Two runs of 6 sqmm and one runs of 6 sqmm cable as earth along with PVC casing caping will be measured as one length.

M&L in repairs for Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.5 of SSR 2020 part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 6 mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion. Note : The rate is ilnclusive of necessary earth work, RFR and removal etc

M/S SUHEEL CONSTRUCTIONS

M/s Riyaz Enterprises

M/S BHAT AND CO