PROVISION OF BATHROOMS AND TOILET AT AULI AND PROVISION OF DRAIN REPAIR AND DRAIN COVER AT JOSHIMATH UNDER GE 871 EWS

Amount

Surface excavation n. exc. 30 cm deep and averaging 15 cm deep and getting in any type of soil.

Excavation in trenches exc 1.5 m wide and not exc 1.5 M depth for foundation and getting out in soft and loose soil.

Returning, filling in including spreading leveling watering and well ramming in layers not exc 25 cm thick in soil.

Removing excavated materials not exc 50 Metre and depositing where directed at a level not exc 1.5 M above the starting point (soil).

M & L hard core of gauge n. exc 63 mm, deposited spreaded and leveled in layer not exc 15 cm thick, watered and rammed to a true surface, broken stone or boulder.

M & L cement concrete 1:4 :8 type D2 using (40 mm graded aggregate) as in filling, foundation, mass concrete and sub base of floors etc.

M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) 75 mm thick as in plinth protection complete all as specified and directed.

M & L for RCC M-25 (design mix using 20 mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M 25 ( design mix using 20mm graded stone aggregate) for lintel beam, roof beam, cantilevers, bressummers etc complete all as specified and directed.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat fair finished surfaces

Use waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports over hangs etc.complete all as specified and directed.

M&L for mild steel TMT steel bars in reinforcement 10mm dia and over cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT steel bars in reinforcement 5mm dia and over up to 10mm dia in stirrups cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 using 20mm graded aggregate as in solid building blocks, exc. 10cm in width and setting in CM (1:6) complete all as specified and directed.

M&L for DPC 40mm thick in cement concrete 1:2:4, type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 using 20mm graded aggregate as in solid building blocks, 10cm in thick and setting in CM (1:4) complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth without using extra cement.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exc. 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed.

M&L for Glazed ceramic tiles Coloured 350 x 250mm/450 x 350mm 8 to 10 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:6 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

S&F mild steel rolled sections as in roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. ( Fe 410-W (Gde E-250) quality A) complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates ( Fe 410-W (Gde E-250) quality A) complete all as specified and directed.

S&F for Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

S&F for Mild steel bolts, purpose made, dia of bolt exc 11 but not exc 15 mm with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 15 cm long but not exc. 22.5 cm long complete all as specified and directed.

S&F for Mild steel bolts, purpose made, dia of bolt exc 11 but not exc 15 mm with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm long but not exc. 10 cm long complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for Pressed steel frames for doors with one or more rebates (Size of frame 105x60mm) including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed

S&F for 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F for Solid PVC door frame of size 50 mm x 47 mm, made out or 5 mm, plain colour PVC sheet, reinforced with MS Square tube all as specified and directed.

S&F for Factory made solid panel PVC door shutter, 30 mm thick (Style) consisting of frame made out of M.S. tubes for top and bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel on both sides having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on both sides and as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement and fixing in the frame at site all as per specification & drawing all as specified and as directed.

S&F for butt hinges medium weight cold rolled mild steel 100 mm complete all as specified.

S&F for Aluminium anodised barrel tower bolt, of extruded section and fixed of 150 mm long complete all as specified and directed.

S&F for 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F for extruded aluminium alloy handles fabricated type, anodised 150 mm long all as specified and directed

S&F for steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed

S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L for preparation of new steel surfaces of any description exc 10cm width or girth and applying two coat of 1st quality synthetic enamel paint over a coat of primer complete all as specified and as directed.

M&L for preparation of new surfaces of wall of any description and applying three coat of white wash complete all as specified and as directed.

S&F 15 mm bore GI tubing medium grade with all fitting fixed to wall and ceiling or laid in floor complete all as specified and directed

All as per item no. 41 above but 20 mm bore complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed fixed in walls and floors or trenches etc. complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed any length with rubber ring joints laid in trenches including taking down complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore pipe complete all as specified.

All as per Srl item No. 45 here in before but 75 mm bore.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal of 75 mm complete all as specified and directed

S&F PVC (SWR) 75 mm single junction T equal or unequal complete all as specified and directed

S&F PVC (SWR) 100 mm single junction T equal or unequal complete all as specified and directed

M&L for 75mm PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) vent cowl bore 110 mm.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding complete all as specified and directed.

Supply and fix Vitreous china urinal, bowl type, flat back, size of 465 x 355 x 265mm (minimum), white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, with grating and union for discharge pipe and PVC waste pipe, including making all connections to existing connections, fixed complete all as specified and as directed.

S&F Vitreous china urinal partition slab white of size 310 mm x 700 mm terminating about 40 cm above floor level complete all as specified and directed.

S&F vitreous china wash hand basin (550x400 mm) white flat back excluding taps, waste chain and plug and porcelain stopper but including brackets complete all as specified and as directed.

S&F 32 mm dia bore waste fittings brass chromium plated for glazed ware sink, basin etc with long screwed shank and fly nut , flange and bedded in red lead cement and other end fixed incl waste pipe of reqd length complete all as specified and as directed.

S&F 15 mm bore pillar tap cast copper alloy with capstan head, fancy type chromium plated screwed down high pressure with or without lettered 'Hot or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F Flushing cistern low level, PVC 10 Ltr capacity symphonic action type valve, valve less with inlet ball valve, float and handle incl bracket complete all as specified and directed.

S&F Flush pipe of polythene of low or high density or PVC, 32 mm dia for low level cistern complete all as specified and directed.

Supply and fix for PVC(LDPE), 32 mm dia, polyethylene, of pressure rating 6 kgf/sqcm, fixed complete to wall, ceiling or in floor, for wash hand basin including taking down of existing old pipe all as specified and as directed.

S&F PVC connection 15 mm dia and 450 mm long complete all as specified and as directed.

S&F CP grating of size 100 mm dia with waste hole complete all as specified

Supply and fix for towel Rail, brass chromium plated. 20 mm dia D type, 600 mm long between flanges complete all as specified and as directed

Supply and fix Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with mild steel chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F soap dish acrylic type complete all as specified

Supply and fix for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

Supply and fix rotational moulded polyethylene water storage tanks ISI marked of 500 litre capacity (Cylindrical vertical with closed top) including 20 mm brass float valve with HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule hoisted and fixed in position all as specified in SSR Part-I ,complete all as specified and as directed.

S&F 15mm dia stop valves/angle valve cast copper alloy, chromium plated, fancy type screwed down high pressure, with crutch or butterfly handle screwed with both ends for iron pipe or for union complete all as specified and directed.

S&F 15mm dia Bib taps, cast copper alloy, chromium plated fancy type, screwed down high pressure, with crutch or butterfly handle screwed with both ends for iron pipe or for brass ferrules and complete all as specified and directed.

S&F sheet glass 3 mm thick of ordinary quality and glazing with oil putty in square n. Exc.0.5 sqm in each pan

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of under ground cable/pipes etc. n exc 10 sq m on plan and n exc 1. 5 m hard /dense soil in depth and getting out complete all as specified and directed.

M&L Cement concrete 1:2:4, type B-1(using 20mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

M&L Extra for forming 30 cm inner girth fair finished drains or channels in cement concrete using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and directed.

Supply only Integral waterproofing compound mixed with plastering of wall surfaces complete all as specified and directed.

M&L Plain cement concrete 1:3:6 type C-1(using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L Providing Precast cement concrete 1:2:4 type B-1(using 20mm graded stone aggregate) in landings, cover slabs as drain cover, chajjas, water troughs, mangers, shelves set in CM 1:4 all as specified and directed.

M&L for point wiring concealed conduit with 1.50 Sqmm PVC FRLS insulated, unsheathed, single core, multistranded copper conductor cable 1100 volts grade including 1.5 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and including rigid PVC conduit of suitable size but not less than 20mm dia size confirming to IS 2079-1973 medium grade with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer, all fittings such as elbows, bends, junction boxes, saddles including PVC board (ISI Mark) and screws and rawal plugs including 3.0mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for following :-

One light/fan/bell point controlled by one ,one way switch .

One socket outlet 5 pin 5/6 Amps on independent board.

One socket outlet 5 pin 5/6 Amps on same board with other switches.

All as per item No 78 above but for socket out let, 15/16 Amps on independent board with 4 Sqmm size cable and 2.5 Sqmm for continuity earth wire connected to common earth dolly all as specified and directed by Engr - in - charge.

S&F switch piano flush type 5/6 Amps single pole one way all as specified & directed.

S&F switch piano flush type 15/16 Amps single pole one way all as specified & directed.

S & F socket out let 5 pin 5/6 Amps all as specified and directed.

S&F socket out let 2-in-1, 6 pin 5/6 & 15/16 Amps all as specified and directed.

S&F ceiling rose 2/3 terminals 65x25 mm dia polycarbonate isolated all as specified & directed.

S&F LED tube light fitting two feet 10 watt, slim design, 230volts, including connected with 3 core 23/0.0076 insulated copper wire from ceiling rose to fitting connector all as specified and directed.

S&F LED tube light fitting bright 18 watt. slim elegant design. and including connected with 3 core 23/0.0076 insulated copper wire from ceiling rose to fitting connector all as specified and directed.

S & F exhaust fan AC single phase 230/240, 50 HZ Volt of size 200 mm sweep MS body heavy duty operating with louvers shutter complete grouting the ragged bolt in wall fixing the frame and exhaust fan fix including louver shutter with frame on the exhaust side and connecting with PVC insulator 3 core 23/0.0076 copper wire rubber insulated from ceiling rose to exhaust fan motor complete all as specified and as directed .

Supply and fix of DB, SPN 4 way double door for MCB, 240 volt with 200 amps rated bus bar with enclosure blank plates for unused all as specified and directed

Supply and fix MCB 6-40 amps, 10 KA, SP 240 volt, 'C' series all as specified and directed

Supply and fix MCB 40 amps, 10 KA, DP 240 volt, 'C' series all as specified and directed

M&L in replacement earthing complete with galvanised steel earth plate electrode size 600X600X6mm thick buried directly in ground vertically to a depth not less than 2.25m deep below normal ground level with top edge of earth plate not less than 1.5m deep below normal ground level and connected to and including GI earth lead wire 4mm dia by means of bolts, nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and all as specified or indicated and testing on completion including excavation and earth work in any type of strata available at site, PCC (1:3:6) type C-1 earthing chamber, pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with GI watering pipe of 20 mm bore medium grade, wire mesh and lugs, GI protection pipe of 15 mm bore light grade up to 7.5 metre long all as specified and directed.

S&F building security light fitting complete with 25 watt LED type pressure die cast aluminium housing and heat resistant toughened glass with frame protection and better optics for uniform distribution complete fixed bracket made out of GI pipe 32 mm dia (light grade) 1.5 metre long and MS clamp and nut bolts washers and connected with twin core cable 1.5 sqmm from ceiling rose to fittings connector all as specified and directed .

M&L local sand dry, filling in trenches around under ground cable complete all as specified and directed.

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply laying and testing cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete all as specified and directed.

Supply and fix of GI tubes light grade, galvanised, 32 mm bore including necessary GI fittings, laid in trenches or under floor or fixed with poles/walls for fixing of air termination complete all as specified and directed.

Supply and fix of GI tubes medium grade, galvanised, 25 mm bore including necessary GI fittings, laid in trenches or under floor or fixed with poles/walls for fixing of air termination complete all as specified and directed.

supply and fixing new Gun metal gate valve/glove valve ISI marked with Iron wheel head screwed both end for GI tubing of size 25 mm dia

M/S Swarn Constructions

M/S ANSULBHUJWAN