WELCOME MAINT AND CERTAIN OTHER MISCELLANEOUS MAINT WORKS TO MD ACCN AT MIL STN PITHORAGARH

Amount

DESCRIPTION OF ITEMS

Demolition of brick work,PCC Block or stone/boulder masonary built in cement mortar/lime mortar including all quoins, arches, pillars etc complete all as spd and directed

M & L precast cement concrete Block Masonary with solid blocks type C1 1:3:6 20mm graded stone aggregate exc 10cm in width and setting in mortar 1:6 including complete all as spd and directed

M&L for brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed

dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc.

M & L for 75mm thick PCC 1:2:4, type B-2 using 40mm graded stone aggregate, as in pavings/hard standing/path etc finished uneven and rough without using extra cement and including demolition complete all as specified & directed.

S & F Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments including 15mm screed bed in CM 1:6 and incl demolition PCC./tile complete all as specefied

S & F Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments including 15mm screed bed in CM 1:6 and incl demolition PCC./tile complete all as specefied

M& L for providing precast cement concrete rubber moulded coloured interlocking tiles/cobble stone 60 mm thick with grey cement and pigment of approved design and pattern complete all as specified and directed

M&L for refixing of interlocking paver blocks incl dismantling complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and direceted.

M & L for 15 mm thick rendering on brick work or concrete surfaces in CM 1:6, surfaces finished even and fair etc and then after preperation of newly plastered surface applying two coat of oil bound distemper over a layer of wall care putty of average thickness 1 mm complete all as specified & directed.

M & L for 15 mm thick rendering on brick work or concrete surfaces in CM 1:4, surfaces finished even and fair etc and then after preperation of newly plastered surface applying two coat of cement based paint complete all as specified & directed.

M & L for rendering 5mm thick in cm 1:4 as in ceiling finished even & fair including Taking down cement plaster of any description raking out of joints, hacking for key, scrubbing down with water etc and then after preperation of surface apply three coat of white wash on ceilling . complete all as specified & directed.

Taking down old cement plaster any description on brick or stone wall/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete as specified and directed.

M & L for 15 mm thick rendering on brick work or concrete surfaces in CM 1:4, surfaces finished even and fair complete all as specified & directed.

M&L three coat of white wash on walls including preparation of new plastered surface and complete all as specified.

M&L for applying one coat of oil bond distemper on old distempered surfaceses of walls of old treated surfaces all as specified including preparation of old surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soots and efflorescence salts ,removing nails and making good complete all as specified.

M & L for preparation (making surface good with putty wherever require) of old decorated surfaces of walls and applying one coat of exterior weather proof acrylic emulsion paint complete all as specified.

M&L for applying one coat of synthetic enamel paint including preparation of old steel surfaces of any description over 10cm width or girth all as specified.

M&L for applying one coat of synthetic enamel paint including preparation of old painted wooden surfaces of any description over 10 cm width or girth all as specified.

M&L for applying one coat of white wash on plastered or unplasred surfaces of walls of old treated surfaces all as specified including preparation of old plastered surfaces or unplastered white washed walls by brooming down or steel wire brushing , scrapping down smoke soots and efflorescence salts ,removing nails and making good complete all as specified.

All as per item No above but on ceiling surfaces.

S & F in repair PVC cabinet mirror size 350mm x 450 mm fixed with steel screws with rowel plug complete all as specified and directed

S & F rotational moulded polyethylene three layered water storage tanks 500 Litres capacity (cylindrical, vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I including taking down existing water tank complete all as specified & directed.

S & F rotational moulded polyethylene three layered water storage tanks 1000 Litres capacity (cylindrical, vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I including taking down existing water tank complete all as specified & directed.

S & F (in repair) 15 mm bore fancy type bib taps brass chromium plated screwed down, screwed for iron pipe or for brass ferrule including flench complete all as specified & directed.

S & F (in repair) 15mm bore pillar taps, brass chromium plated, screwed down high pressure with or without lettered, hot or cold with long screwed shanks and fly nuts, screwed to iron pipe complete all as specified & directed.

S & F (in repair) 15 mm dia chromium plated angle cocks/stop valves, brass, screwed down, high pressure with crutch or butterfly handle, flench screwed both ends for iron pipe or for union complete all as specified & directed.

S & F (in repairs) 15 mm bore concealed stop cock, chromium plated, cast copper alloy, screwed down with crutch or butterfly handle screwed both ends complete all as specified & directed.

S & F in repairs 20 mm bore PTMT ball valves, high pressure with polyethylene float and fly nuts complete, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S & F in repairs 32mm dia bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms)

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. (Cat No. F5001114 or equivalent)

S & F (in repairs) vitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with integral foot rest including replacement of ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed.

S & F (in repair) vitreous china wash down water closet pan (pedestal pattern), white, including plastic seat cover and flushing pipe complete all as specified & directed.

S & F (in repairs) PVC low level flushing cistern 10 Litre capacity, symphonic action type, white as approved including ball valve, float valve and handle, flush pipe complete all as specified & directed.

S & F (in repairs) vitreous china wash hand basin, white, size 550 x 400 mm (shape of basin as directed by engg in charge) including brackets, chromium plated waste coupling &PVC waste pipe of 32 mm dia complete all as specified & directed.

S & F in repairs 600mm long PVC connection, 15 mm bore complete all as specified & directed.

S & F in repair Brass CP towel rail 600 mm long as a approved quality complete all as specified & directed

S & F in repairs 20 mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified & directed

S & F in repair plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device

S&F in repairs for Brass chromium plated waste couplings of dia 32 mm for WHB fixed complete all specified and directed

S&F in repairs 40 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

S&F in repairs stainless steel peg set of Six complete all as specified and as directed.

Cutting Chases for concealed water tubing,shelves,chajjas,sunshades etc and making good disturbed surfaces, cutting not exceeding 10 cm girth, on brick walls complete all as specified & directed.

Refixing old serviceable 15 mm GI tubing and connection in new or old position (concealed in Wall, ceiling & floor etc.) including necessary fittings & fixtures etc. incl taking down complete all as specified and directed

Supply & Fix 15 mm bore medium grade galvanised steel tubing with all fittings and fixed complete to concealed in walls and ceiling or laid in floor incl taking down complete all as specified and directed.

Refixing old serviceable 20 mm GI tubing and connection in new or old position (concealed in Wall, ceiling floor etc.) including necessary fittings & fixtures etc. incl taking down complete all as specified and directed

Supply & Fix 20 mm bore medium grade galvanised steel tubing with all fittings and fixed complete to concealed in walls and ceiling or laid in floor and incl taking down complete all as specified and directed.

S & F in repair Kitchen plate rack of stainless steel of size 720mm x 600mm x 230 mm made out of 1 mm thick steel sheet complete all as specified & directed.

S & F in repairs stainless steel sink with draining board, made out of 1mm thick steel sheet for kitchen with waste pipe, CI cantilever brackets, connecting union overall size 915 x 460mm with bowl size 410 x 330 x 160mm complete all as specified & directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as spd and directed

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 600mm x 420mm x 160mm complete all as spd and directed

Providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement .. (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying three coats of elastomaric acrylic water proof coating Make: Dr. Fixit of pidilite or equivalent per sqm in each coat with roller application.(Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up and same third.)

S & F (in repairs) PVC floor trap 75 mm bore including jointing to waste pipe in cement mortar complete all as specified & directed.

S & F (in repairs) 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls/floors with necessary fittings complete all as specified & directed.

S & F in repairs PVC (SWR) bends 110 mm bore complete all as specified & directed.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floors etc complete all as specified & directed.

S & F in repairs 75 mm bore PVC (SWR) bends complete all as specified & directed.

S & F in repairs 40 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floors etc complete all as specified & directed.

M&L for , false ceiling consisting of wall angles ,main T ,cross T all of size 25 mm X25mmX1.4mm thick power coated GI grid frame work jointed angle as directed and mild steel hooks not less than 4 mm dia with arrangement for adjusting heights of ceiling with and incl provision of 4 mm thick E boards sheet in panels of size 600mmX600mm with necessary off cuts and fixing arrangements for ceiling ,tube light fitting incl dismantling of existing false ceiling and taking down and refixing of electric fitting care fully complete all as specified and as directed.

M&L for of 4 mm thick E boards sheet in panels of size 600mmX600mm with necessary off cuts and fixing arrangements for ceiling ,tube light fitting incl dismantling of existing false ceiling and taking down and refixing of electric fitting care fully complete all as specified and as directed.

M&L for repair to leakage /seepage from 'J' Hooks of CGI /AC/Galvalume roof sheets by replading cup washer and bitumen washer including necessary T & P complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 Sqm and n.exc 4.00 Sqm each. complete all as specified & directed.

Taking down shutters of any description exc. 1 Sqm & n.exc 2 Sqm each complete all as specified & directed.

Taking down shutters of any description not exc. 1.00 Sqm each complete all as specified & directed.

Refixing of shutters of any description exc 2 Sqm each in same opening including taking down, easing and adjusting and also refixing builders hardware as required

Refixing of shutters of any description exc 1 Sqm but n.exc 2 Sqm each in same opening including taking down, easing and adjusting and also refixing builders hardware as required

S & F of second class hard wood (Sal) as in plain, solid , straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified & directed.

S&F for Pressed steel frames for doors (125X60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified directed

S&F for Pressed steel frames for doors (105X60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified directed

S & F 28-30mm thick second class hard wood glazed and skeleton door shutters (three panels), open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framming plain, chamfered or rounded fitted with cut and mitred beads or securing glass etc, size of members of shutters all as per clause No 8.20 (a) of SSR Part-I (2009).

S & F 28-30 MM mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both side complete all as specified & directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fit-ted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening as per specification complete all as specified and directed

S&F in repairs factory made PVC Cupboard frame of the size 75mm x 40mm with a wall thickness of 5mm, made out of extruded 5mm thick plain/prelam PVC sheet of density 600 kg/cbm, having bottom width of 50mm and thickness of 10mm. All four frame lengths reinforced with 15 mm x 15mm M. S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners adjointed with 2 nos. of 15mm long brackets 0f 10mm x10mm M S square tubes. The door frame shall be fixed to the wall using 8/100 long M S screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member and minimum of 2nos. of screws to be provided horizontal member etc. complete as per direction of Engr-in-Charge, manufacturer's specification and drawing.

S&F factory made PVC cupboard flush type shutter of 30mm thick consisting of frame made out M S tubes of 19 gauge thickness and size 19mm x 19mm for stiles and rails. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement/ cynoacrylate adhesive with 5mm thick plain/prelam PVC sheet, on both side of inside panel incliding necessary items to fix the shuter to frame such as 100mm stailess steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutter.All four edges of the panel to be sealed with lipping of 10mm thick and 20mm wide PVC sheet baton (made by sticking 2nos. PVC foam sheet of 5mm thickness using PVC solvent cement adhesive). complete as per direction of Engr-in-Charge.

S&Fin repairs mild steel helical door spring 150 mm long ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed

S&F in repairs Door closer aluminium (extruded section) hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixecomplete all as per direction of engineer in charge

S&F Aluminium annodised barrel tower bolt of extruded section and fixed 200 mm size with bright bolt complete all as specified and directed.

S & F 250mm Aluminium alloy anodised sliding door bolts with hasp,staple(bolt type)and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or aluminium alloy and fixed.

S&F, aluminium handles 150mm size, cast type, anodised complete all as specified and directed.

S & F Butt hinges 100 mm, extruded aluminium alloy with galvanized mild steel hinge pin, anodised of type C-21 and complete all as specified and as directed.

S & F aluminium handles 125 mm long, cast type, anodized complete all as specified & directed.

M&L, preparing of new wooden surface exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F in repair sheet glass 3 mm thick ordinary quality and glazing with beads fixed with metal pins / Oil putty glazing rubber or aluminium beading in square n.exc 0.5 sqm in each pane including hacking out of old broken glass complete all as specified

S&F in repair for figured glass,pin headed type thickness 3 mm thick and glazing with oil puttty/rubber and aluminium beading in square n.exc 0.5 sqm in each pane in repair complete all as specified and directed.

S&F in repairs PVC boards 19/20 mm thick any colour as in cabinets incl sshelves and shutters, fixed with screws and adhessive as per direction of Engr-in-Charge and, manufacturer's instructions including piano hinges, magnet catcher, handles etc

S&F in repairs 18-19 mm thick block board core grade 2 quality interior grade , commercial type on both sides including piano hinges, magnet catcher, handles etc complete all as specified and as directed.

S & F mild steel work as in bands, straps, hold fast, wall ties, hooks for hanging fans, angle cleats & similar small articles conforming to Fe-410-0 or Fe-310-0 complete all as specified & directed.

S&F Powder coated aluminium window , ventilator, shutters and kitchen cupboards, side hung type/ slidding type/Louvered Ventilator without sash bars, alumimium section weighing 0.55 kg/m including necessary joining cleats glazing clips, ruber packing, aluminium snap beading screws aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 No) suitable handle (1 No) and door spring for door complete all as specified

S&F Powder coated aluminium frame and shutter for doors and frame for windows, ventilators and kitchen cupboards frame with one or more rebates including joining cleat for fixing etc. complete all as specified

Supply and Fixing sheet glass 4-5 mm thick ordinary quality and glazing with oil putty or rubber and aluminium beading in squares n. exc 0.5 sqm in each pane complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or weldedcomplete all as specified and directed.

S&F Steel windows with side hung shutters including Box type hinges with steel handle, and steel tower bolt, complete with out glazing bars, dovetailed or welded complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nomonal dia of bar and 1.18 mm avrage width of aperture ,fixed with tined tacks or galvanised wire staples complete all as specified and as directed.

S&F mild steel framed work such as grills grating etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars, barrel iron doors ladders framed balusters walk ways railing frame work of water tanks, hole fast and similar work confirming to Fe -290 Gde-E-165 all as spd and directed .

M&L, preparing of new steel surface exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S & F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.4 mm complete all as specified & directed.

S & F in repairs 300 mm long mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified & directed.

S&F in repairs door seal of aluminium powder coated with cotton mat of length 90 cm to 100 cm long complete all as specified and directed.

S&F as in repairs 200mm aluminium anodised barrel tower bolts of extruded section all as specified

S&Fas in repairs 150mm aluminium anodised barrel tower bolts of extruded section all as specified

S&Fas in repairs 300mm aluminium anodised sliding door bolt of extruded section all as specified

S&F as in repairs 150 mm extruded aluminum alloy handles, fabricated type anodised.

S&F as in repair 100 mm Butt hinges, medium weight, cold rolled mild steel, fixed to steel frames with and including welding etc complete all as specified

S&F 0.63mm thick galvanised corrugated mild steel sheeting with two corrugation side laps fixed with coach screws and washers in roofs etc with grade of zinc coating 275 including dismantling and prepararing new zinc (or galvanised ) surfaces to receive painting , by coating with mordant solution including washing and cleaning,and preparation of new or previously untreated steel surfaces over 10cm in width or girth and applying two coats of antisol roof paint (MB Green) over one coat of red oxide complete all as specified and as directed.

Supply and fixing 0.63 mm thick plain galvanised mild steel sheeting as in ridges, hips, valley gutter, drip, crumple and straight flashing (length and girth as fixed) with grade of zinc coating 275, corrugated mild steel sheeting with two corrugation side laps fixed with coach screws and washers in roofs etc with grade of zinc coating 275 including dismantling and prepararing new zinc (or galvanised ) surfaces to receive painting , by coating with mordant solution including washing and cleaning,and preparation of new or previously untreated steel surfaces over 10cm in width or girth and applying two coats of antisol roof paint (MB Green) over one coat of red oxide. complete all as specified and as directed

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / clading to wall, fixed with self tapping screw including dismantling all as specified

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / clading to wall, fixed with self tapping screw as including dismantling all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed

S&F rolled mild steel section as in main and cross beams hip and jack rafters , purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-290, Gde E-165 all as specified and directed.

All as per item no above but except material complete all as specified and as directed.

S&F in repairs of magnet catches in cupboard/ kitchen cabinet to receive shutter and fixed with including fittings complete all as specified and directed.

Providing cement concrete 25 mm thick type B-1 (1:2:4) using 20 mm graded agg as in sub base to flooring .

M & L, non skid joint free coloured ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade, including dismantling tile complete all as specified and directed

M & L, non skid joint free coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 Sqm, in floors over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in coloured cement to match including dismantling complete all as specified and directed

M & L, non skid joint free coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 Sqm, in skirting dado over and including 10 mm thick rendering in CM1:4 etc set & jointed in neat cement slurry and pointed in coloured cement to match including dismantling complete all as specified and directed

M & L, Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in CM1:4 set & jointed in neat cement slurry & pointed in coloured cement to match including dismantling complete all as specified and directed.

M & L, Glazed ceramic tiles in vertical surface of size 300x 600x 8 to 10mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in CM1:4 set & jointed in neat cement slurry & pointed in coloured cement to match including dismantling complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl screeding 15mm thick in CM 1:6 incl dismantling complete all as specified and directed.

M&L for vitrified Ceramic Double charge tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl screeding 15mm thick in CM 1:6 incl dismantling complete all as specified and directed.

M & L for non skid tiles, exterior grade, pattern of size 300x300mm, 8-10mm thick set and jointed in neat cement slurry and pointed in white/ coloured cement to match the shade as in floor over and including 15mm thick cement screed bed in CM 1:4 and dismantling of existing tiles complete all as specified and as directed.

M & L for non skid tiles, exterior grade, pattern of size 600x600mm, 10-12mm thick set and jointed in neat cement slurry and pointed in white/ coloured cement to match the shade as in floor over and including 15mm thick cement screed bed in CM 1:4 and dismantling of existing tiles complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick with white marble all arond 150mm wide over and including 15mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finshed polishing including demolition complete all as specified.

M&L for machine cut kota stone slab, 18-20 mm thick in riser and thread single piece on steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 including grinding and mirror finshed polishing including demolition complete all as specified and directed.

M&L for Granite (of any type of coloured) work (table rubbed and polished) 14-16 mm thick in steps jambs,pillars, window cills, cooking plateform /partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:6 incl moulding, chamfering of edges including demolition complete all as specified.

S&F in repair CP brass wall mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore complete all as specified and directed.

S&F in repair brass spindle for central hole basin mixer /bib tap (as per sample) for mixing hot & cold water screwed down for iron pipe and fixed with pvc conncetion complete all as specified and directed.

S&F in repair CP Brass central hole basin mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore complete all as specified and directed.

S&F in repair brass legs for wall mixer/pillar cock fixed with pvc conncetion complete all as specified and directed.

S&F in repairs curtain rod made of SS pipe dia of rod 20 mm with decorative brackets and ends complete all as specified and as directed.

S & F in repair water Jet for EWC chromium plated with PVC connection complete.

S&F in repairs C P coated Hand shower (health faucet) 1 mtr PVC tube with wall hook complete for EWC, all as specified and directed.

S & F in repair Brass chromium plated shower rose 125mm size incl shower arm complete all as specified and directed.

S & F (in repair) CP brass soap dish complete all as specified & directed.

S & F (in repairs) chromium plated Gratings 125 mm size complete all as specified & directed.

S&F in repairs PVC waste pipe 32 mm to 40 mm dia size of adequate length (minimum length 60cms) suitable for WHB/Sink with PVC adapter fixed complete all specified and directed

S&F in repairs PVC water tank covers of capacity exc 250 Ltrs not exc 500 Ltrs complete all as specified and directed.

S&F in repairs PVC water tank covers of capacity exc 500 Ltrs not exc 1000 Ltrs complete all as specified and directed.

Repair to low level flushing cistern PVC for making it fully functional and leak proof by replacing PVC syphon kit complete all as directed and specified.

S & F in repairs double legged door stopper of allluminium alloy with rubber

M&L superthermolay waterproofing APP membrane thickness 1.2mm polyster etc including laying on Roof sheet for leakage/seepage all as specified and directed

M&L water proof glue painting on roof /wall etc to protect water leakage/seepage all as specified and directed

S&F in repair 15mm bore fancy type bib taps (Long body ) brass chromium plated screwed down ,screwed for iron pipe or for brass ferrule including flench complete all as specified & directed .

S&F in repair 15mm bore fancy type bib taps (Two way ) brass chromium plated screwed down ,screwed for iron pipe or for brass ferrule including flench complete all as specified & directed .

Material & Labour for Providing Precast cement concrete type B1 (1:2:4) 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles set in cement mortar ( 1:6 ) incl form work demolition complete all as specified and directed.

Material & Labour for 6 to 8 mm dia TMT bars , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for complete removal of existing treatment using mechincal device and applying two coat Oil bound distemper (acrylic emulsion ) on old plastered wall with airless electric sprayers after prepearing old surface applied using airless electric sprayers over one coats of wall care putty of 1-1.5mm thickness prepared and sanded with electrically operated sanding machine. application to be done through the authorised applicator of manufacturer complete all as specified and directed..

M&L for complete removal of existing treatment using mechincal device and applying two coat Oil bound distemper (acrylic emulsion ) on old plastered ceiling surface with airless electric sprayers after prepearing old surface applied using airless electric sprayers over one coats of wall care putty of 1-1.5mm thickness prepared and sanded with electrically operated sanding machine. application to be done through the authorised applicator of manufacturer complete all as specified and directed..

S & F 20/25mm mm dia fancy type Drapery Rod with rubber sleeves including brackets complete, of approved quality and all as directed including taking down existing curtain rod complete all as specified & directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified.

Point wiring in replacement of one light point/fan/bell point controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size 25mm dia with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size & as directed & 3 mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified.

All as per srl item No-2 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit.

All as per srl item No-2 here in above but for one 3 pin 5A socket outlet independent with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit controlled by one switch

All as per srl item No-2 here in above but for one 5A socket outlet on the same board with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit controlled by one switch

Point wiring in replacement of one light point/fan/bell point controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size 25mm dia with all fittings (ISI Marked) controlled by one switch including including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories as directed, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified.

All as per srl item No-6 here in above but for one socket outlet 5 amps on indipendent board with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit controlled by one switch with including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories as directed.

All as per srl item No-6 here in above but for one socket outlet 5 amps on same board with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit controlled by one switch including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories as directed.

All as per srl item No6 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories as directed.

Point wiring in replacement of one light point/fan/bell point controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in PVC casing & caping with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size & as directed & 3 mm thick plastic laminated sheet,

All as per srl item No-10 here in above but one 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size

All as per srl item No-10 here in above but one 3 pin 5 Amps socket outlet independent switch board of light points in the same vertical plane, with cables, 1.5 sq. mm size

All as per srl item No-10 with n above but for one 3 pin 15 Amps socket outlet independent with 4 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 4 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of piano/modular plate with all accessories as directed.

S&F in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 2x4 sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 4 Sqmm as earth lead in & including concealed PVC conduit medium grade 25mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification all as required at site or directed.

All as per srl item No-14 here in above but in existing concealed conduit .

All as per srl item No-14 here in above but for cable of size 2x6 sqmm and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 6 Sqmm as earth lead in & including concealed PVC conduit .

All as per srl item No-14 here in above but for cable of size 2x6 sqmm and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 6 Sqmm in existing concealed conduit.

S&F in replacement for switch piano flush button single pole one way 5/6 amps 240 volts.

S&F in replacement switch piano flush button single pole one way 15/16 amps 230 Volts.

S&F in replacement for socket 5 amps 5 pin flush type, 230 volts.

S&F in replacement for socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts.

S&F in replacement for ceiling rose surface bakelite 3 terminals.

S&F in replacement Lamp holder insulated body with back plate for dome batten fittings.

S&F in replacement of fan regulator electronic, 5-step 2 mod type hum free suitable to control speed of fan from 0 to 100% and connecting electrically all as required or directed by engineer-in-charge.

S&F in replacement of switch modular type single pole one way 1 module 6 amps 240 volts.

S&F in replacement of switch modular type one way 1 module 16 amps 230 Volts.

S&F in replacement of socket 6 amps modular type 2/3 pin combined 2 module , 230 volts.

S&F in replacement of socket modular type , 2/3 pin, 6 and 16 amps combined 2 module, 230 volts.

S&F in replacement of electronic regulator 5-step 2 mod type modular type one way 230 Volts.

S&F in replacement of bell push AC SP 240 volts flush type 5/6 Amps, single pole one way complete as all specified and directed.

S&F in replacement of bell electric multi music type / AC SP 240 Volts Complete all as specified and directed.

S&F in replacement of capacitor 2.5 mfd, ± 5%, 440V, AC, 50 Hz after removing old/defective condenser complete all as specified an directed.

S&F in replacement of Tube light fitting integrated type suitable for LED 20W(4 feet) indoor decorative aluminium extruded LED batten complete with housing with all accessories pre wired and making connection with three core copper flexible cable from ceiling rose to PVC connection to light fitting complete all as specified and directed.

S&F in replacement of Tube light fitting integrated type suitable for LED 10W (2 feet) indoor decorative aluminium extruded LED batten complete with housing with all accessories pre wired and making connection with three core copper flexible cable from celling rose to PVC connection to light fitting complete all as specified and directed.

S&F in replacement of LED bulk head fitting with opal diffuser min 10 Watt, 6500 K, IP-65, with efficient heat dissipation and integrated electronic driver complete connecting electrically all as directed.

S&F in replacement of 5 A Switch Socket Combination with PVC Box as per directed by engineer in charge.

S&F in replacement of 15 A Switch Socket Combination with PVC Box as per directed by engineer in charge.

S&F in replacement of LED Bulb 9 W all as specified and directed.

S&F in replacement of Decorative Gate Light made up of high grade unbreakable ploycarbonate material Globe type of dia min 200 mm suitable for 9/10 w LED Lamp including fixing of GI pipe of suitable dia, any mm long light grade, partly embedded on column of gate with fixing arrangement complete and making electrical connection complete all as spfd. Make : C&S/Havells/Phillips/Bajaj/Wipro

S&F in replacement of LED post top lantern 35/40 Watt warm white/white made in die cast aluminium housing with decorative clear opal acrylic diffuser and IP-65 protection including fixing of GI pipe of suitable dia dia, 300 mm long light grade, partly embedded on column of gate with fixing arrangement complete and making electrical connection complete all as spfd. Make : C&S/Havells/Phillips/Bajaj/Wipro

S&F in replacement of High power LED security light 50 Watt IP 66 Energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source and electronic driver incl suitable size service bracket fixed with clamps, nut, bolt and washer and electric connection with 1.5 Sqmm multistranded twin core alum cable PVC insulated complete all as spfd.

S&F in replacement of Metal Clad type AC Box steel enclosure plug and socket copmlete with one SP MCB 25 Amps, 240 Volts.

S&F in replacement of modular type AC Box steel enclosure plug and socket copmlete with one SP MCB 25 Amps, 240 Volts.

S&F in replacement of Vertical type TPN DB, 4 Way, as per IS-8523, IP-42 protection, universal mounting with 100A copper bus bar with neutral bar, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for MCCB 125 Amps TPN as incomer and MCB TP as outgoing, with and including providing following MCCB/MCBs & making necessary electrical connection for Incoming & outgoing cables, with copper lugs, crimped with crimping tool:-a) Incoming:- MCCB, TPN, 415 Volts, 125 Amp ultimate breaking capacity (Icu)-25 KA, confirm to IEC-60947-2-01 No (b) Out going MCBS:- MCB TP 415 volts 63 Amps having repturing capacity 10 kA, 'C' curve type-4 Nos

S&F in replacement of Thermal magnetic release MCCB 4 pole 415 volt rapturing capacity 25 KA of size 125 amp complete all as specified.

S&F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 IK-09 protection with metal door single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

All as per item No 39 but for 8 way.

All as per item No 39 but for 12 way.

S&F in replacement of Amp rating 240,10 KA C- curve MCB SP of 6 to 32 Amp with connection testing and commisioning.

S&F in replacement of Amp rating 240,10 KA C- curve MCB DP SPN of 32 Amp with connection testing and commisioning.

S&F in replacement of Amp rating 240,10 KA C- curve MCB DP SPN of 40-63 Amp with connection testing and commisioning.

S&F in replacement of Amp rating 415,10 KA C- curve MCB TPN of 40-100 Amp with connection testing and commisioning.

Supply and fix in repairs Single core unsheathed 1100 volts PVC-FRLS insulated wire with copper conductor(multistrand) ISI marked of size 1.5 Sqmm, complete all as specified and directed.

Supply and fix in repairs of Single core unsheathed 1100 volts PVC-FRLS insulated wire with copper conductor(multistrand) ISI marked of size 2.5 Sqmm, complete all as specified and directed.

Supply and fix in repairs Single core unsheathed 1100 volts PVC-FRLS insulated wire with copper conductor(multistrand) ISI marked of size 4.00 Sqmm, complete all as specified and directed.

Supply and fix in repairs of Single core unsheathed 1100 volts PVC-FRLS insulated wire with copper conductor(multistrand) ISI marked of size 6.00 Sqmm, complete all as specified and directed.

Supply & fixing in repair of 1100 volts grade heavy duty cable with PVC insulated aluminiuum conductor served with an inner sheating of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4mm suspention wire one twin core flat/circular 10sq mm solid conductor.

Supply & fixing in repair of 1100 volts, 3 core flexible cable with PVC insulated copper conductor with each core 2.5 sqmm all as specified and directed.

M/S KS Shahi and Sons (BID ID -3412025)

SANJEEV ENTERPRISES (BID ID -3412321)