CONST OF BUILDING WORK REMAIN WORK BALUGANG ROAD OF DISPENCERE AND SHOP AT NAGAR PALIKA MUSSORIE 02

Side Clearance including all labour and T&P

15.56 Dismantling old plaster or skirting ranking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping groundwith in 50 meters lead.

15.1 Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead as per direction of Engineer-in-charge.

2.6 Earth work in execavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out land disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge 2.6.1 All kind of soil

4.1 Providing and laying in possition cement concrete of specification grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.8 1:4:8: (1 Cement : 4 coarse sand (Zone - III) : 8 graded stone aggregate 40 mm nominal size)

5.15 Providing, hoisting and fixing above plinth level up to floor five level precastreinforced cement concrete in lintels, beams and bressumers, including setting in cement mortar 1:3 ( 1 cement : 3 coarse sand), cost of required centering and shuttering but, excluding the cost of reinforcement, with 1:1:2 ( 1 cement : 1.5 coarse sand (zone - III) : 3 graded stone aggregate 20 mm nominal size)

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

12.41 Providing and fixing on wall face unplasticised Rigid rain water pipes conforming to IS : 13592cType A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single Socketed pipes (weepholes)

5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level 5.22.6 Thermo-Mechsnicslly Trested bars of grade Fe-500 D or more

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level in all shapes and size in :6.4.2 Cement mortar 1:6 ( 1 cement : 6 coarse sand)

12 mm cement plaster of mix 1:6 (1 cement : 6 fine sand) (13.1.2) DSR-

13.3 20 mm cement plaster of mix: 13.3 20 mm cement plaster of mix:

2-1 Cement plum Masonry with 40% plum & 60 % 1:3:6 cement concrete including supply of all material, labout, T&P etc. required for proper completion of the work. As per drawings and technical specification Clause 802, 803, 1202 & 1203 of MORD Specification (with 12% G.S.T rate including) (4344.40*.12=521.33=(4344.40+521.32=4865.73)

10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel ect. As required. 10.25.2 in gratings, frames, guard bar, ladder, raillings, brackets gatesand similar works

9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in possition with hold fast lugs or with dash fasteners of requied dia & length (hold fast lugs or dash fastener shall be paid for separately) 9.1.2 Sal wood

9.20 providing and fixing ISI marked flush door shutters conforming to IS: 2202(part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 9.20.1 35 mm thick including ISI marked Stainless steel but hinges with necessary screws

11.41 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufaacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4( 1cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with ehite cement and matching pigments etc. complete 11.41.3 Size of Tile 800x800 mm

13.80 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete

13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade 13.41.1 New work( two or more coats) over and including waterthinnable priming coat with cement primer

13.61 painting with syntetic enamel paint of approved brand and manufacture to give an even shade: 13.61.1 Two or more coats on new work

Finishing walls with textured exterior paint of required shade: New work(Two or more coats) of (MR)

13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.3 painting Steel work with Deluxe Multi Surface paint togive an even shade. Two or more coat applied @0.90 ltr./10 sqm of approved brand and manutacture

21.3 providing and fixing glazing in aluminium door, window, Ventilator shuttersand partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the diretions of engineer-incharge.(Cost of aluminium snap beading shall be paid in basic item)21.3.1 with float glass panes of 4.0 mm thickness(weight notless than 10kg/sqm)

4.1 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level: 4.1.3 1:2:4( 1cement :2 coarse sand(Zone-III): 4 graded stone aggregate 20 mm nominal size)

4.11 providing and laying c.c floor 50mm thick with cement concrete 1:2:4( 1 cement :2 coarse sand(Zone-III):4 graded stone aggregate 20 mm nominal size

16.70 providing and fixing G.I chain link fabric fencing of width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in charge. 16.70.2 Made of G.I wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colur and shade

10.6 Supplyinh and fixing rolling shutters of approved make, made of required size M.S laths, interloacked together through their entire length and jointed together at end by end locks, mounted on specially designed pipe shaft with brckets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strenght conforming to IS: 4454-part 1 and M.S. top cover of required thickness for rolling shutters. 10.6.3 80x0.90 mm M.S laths with 0.90 mm thick top cover

10.7 providing and fixing ball bearing for rolling shutters

10.30 Providing & fising glass panes with putty and glazing clips in steel doors, windows, clerestory windowss, all complete with : 10.30.2 5.5 mm thick glass panes

12.1 providing corrugated G.S sheet roffing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I limpet washers or with G.I limpet washers filled with white lead, including a cost of approved sheel primer and two coats of approved paint on overlapping of sheets complete( up to any pitch in horizontal/vartical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m2

12.31 Providing 10 mm thick plaster of paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame( frame work to be paid separately): 12.31.1 Flat surface

Sanitary fittings

17.2 Providing and fixing white vitreous china pedestal type water closet (European type W.C pan) with seat and lid, 10 litre low level ehite P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) , conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.2.1 W.C pan with ISI marked white solid plastic seat and lid

17.7 Providing fixing wash basin with C.I brackets, 15 mm C.P brass pillar taps, 32 mm C.P brass waste of standard pattern, including painting of fitting and brackets , cutting and making good the walls wherever require: 17.7.2 white Vitreous China Wash basin size 630x450 mm witha single 15 mm C.P. brass pillar tap

Providing & Fixing of 15 mm G.I class 'B' Pipe(Jindal hissar Make) complete with G.I. fittings & clamps including supply of all materials, labour and T&P etc and including making good the wall etc.(internal work)) as per D.s.r code no 18.12.1 15 mm dia nominal bore

18.12.2 20 mm dia nominal bore

18.48 providing and placing on terrace (at all floor levels) polyetthlene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 18.18.2 20 mm norminal bore

18.16 Providing and fixing brass stop cock of approved quality 18. 16.2 20 mm norminal bore

18.21 Providing and fixing uplasticised PVC connection pipe with brass unions : 18.21.2 45 cm length 18.21.2.1 15 mm norminal bore

18.49 Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931:18.49.1 15 mm nominal bore

18.53 Providing and fixing C.P brass angle valve for bain mixer and geyserpoints of approved quality conforming to IS: 893118.53.1 15 mm nominal bore

18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 Coarse Sand) for water meter complete with C.I double flap surface box 400x200x200 mm(inside) with locking arrangement and RCC top clab 1:2:4 mix(1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size),i/c necessary excavation, foundation concrete 1:5:10 ( 1cement :5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard degin 18.37.1 with common burnt clay F.P.S(non modular) bricks of class designation 7.5

17.31 providing and fixing 600x450 mm beveled edge mirror of superior galss(of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P brass screws and washers complete.

8.1 Marble work gang saw cut(polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grount of average 12 mm thick in cement mortar 1:3 ( 1cement: 3 Coarse Sand), including pointing with ehite cement mortar 1:2( 1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be securedto the backing by means of cramps, which shall be paid for separately 8.1.1 aj Nagar Plain white marble/Udaipur green marble/Zebra black marble. 8.1.1.1 Area off slab upto 0.50 sqm

Item Drainage

12.41 Providing and fixing on wall Face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.12.41.1 75 mm diameter

12.41 Providing and fixing on wall Face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.12.41.2 110 mm diameter

Item Electrical fittings

Wiring point for light with 1.50 sq. mm PVC insulated single core cable in HD PVC condute pipe on surface complete with 1.50sq. Mm PVC insulated Aluminium conductor cable as earth continuity wire drawn inside the conduit complete in all respect. (M.R)

Light Rate

Tube Light/led Light

fan with box/ fan

Fan with box rate/ exest fan

plug point box

MCB box

C S RAWAT

RADHEY SHAYAM SHARMA