CERTAIN REPAIR TO VARIOUS OTM ACCN IN LOWER AREA AND SECTION HOSPITAL TA BN COMPLEX UNDER AGE BR II AT IMA DEHRADUN

Amount

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Demolition of old brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area n.exc 1.50 Sqm each complete all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n.exc 4.0 Sqm each ccomplete all as specified and directed

Taking down shutters of any description.exc 1 Sqm and n.exc 2 sqm each complete all as specified and directed.

Taking down shutters of any description. n.exc 1 sqm each complete all as directed

Factory made solid panel PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for top & bottom rails ms frame shall be covered with heat moulded plain colour PVC "C" channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 etc complete all as directed

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixing in opening as per specification and drawing in SSR complete all as specified and directed

15mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) complete and jointed, tested and fixed to wall and ceiling or laid in floors including taking down existing tubing, complete all as specified and directed

20mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) complete and jointed, tested and fixed to wall and ceiling or laid in floors including taking down existing tubing complete all as specified and directed

Rendering 5mm thick plaster in CM (1:3) on concrete surface of ceiling finished even & smooth without using extra cement complete all as specifiied and directed

Rendering 10mm thick plaster on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth without using extra cement and mixed with water proofing compound as per manufactures instructions, (work to be carried upto 7.5 Mtr height) complete all as specified and directed. Note- WPC will be measured paid as supply only under respective items separetely

Rendering 15mm thick plaster on other than fair faces of brick work or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Preparation of new plastered or unplastered surface of ceiling and applying three coat of white wash complete all as specified and directed.

Preparation of new plastered or unplastered surface of wall and applying three coat of white wash complete all as specified and directed

Preparation of old plastered/un-plastered surfaces of wall by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including cornices, pillar etc and applying one coat of white wash on walls complete all as specified and directed

Preparation of new plastered surfaces of wall and applying two coats of snowcem (cement base paint) over a coat of cement primer on walls complete all as specified and directed.

Preparation of old plastered/un-plastered surfaces of wall by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including cornices, pillar etc and applying one coat of cement base paint (snowcem) complete all as specified and directed.

Brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed

75mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in plinth protection or similar places, and finishing the surface even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with sealing compound grade 'A' including necessary formwork etc and including demolition of existing old cement concrete in ground floors and pavings n.exc 15cm thickness (below or above) ground level complete all as specified and directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor including demolition of existing old cement concrete etc complete all as specified and directed.

100mm thick PCC 1:2:4 type B2 using 40mm graded crushed stone aggregate as in hardstanding including necessary formwork and spike rolling or making impression of expanded metal while the concrete is green etc and including demolition of existing old cement concrete in complete all as specified and directed.

30mm thick 2nd class H.W. factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc (with sash bars) devided into squars, edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/gauze etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed.

35mm thick 2nd class H.W. factory made plain framed panelled shutters (any number of panels) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both face, size of rails and stiles as per IS 1003 (part-I) kiln seasoned and chemical pressure treated complete all as specified and directed.

35mm thick 2nd class H.W. factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc(with sash bars) divided into squars, with plain chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitered beads for securing glass/gauze etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

2nd class hard wood, plain straight chowkats & frame wrought rounded or chamfered put together with glue pinned at joints and fixed complete all as specified and directed.

Hacking out old broken glass pane (any size thickness and description) from wooden frames complete all as specified and directed

3mm thick sheet glass ordinary quality in square n exc 0.50 sqm each pane glazed with oil putty or fixed with wooden bead complete all as specified and directed

Butt hinges, 100mm long, medium weight, cold rolled, mild steel complete all as specified and directed

Butt hinges, 75mm long, medium weight, cold rolled, mild steel complete all as specified and directed

200 mm long aluminium anodized, barrel tower bolts of extruded seciton and fixed (ISI marked) complete all as specified and directed

100 mm long aluminium anodized, barrel tower bolts of extruded seciton and fixed (ISI marked) complete all as specified and directed

150mm extruded aluminium alloy handles, fabricated type, anodized complete all as specified and directed

100mm extruded aluminium alloy handles, fabricated type, anodized complete all as specified and directed.

300mm long aluminium anosized sliding door bolt with hasp staple (bolt type) and fixing clips to sheet cast or extruded section of cast aluminium complete all as specified and directed

Floor door stoppers of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in door, overall length of cover plate 150mm complete all as specified and directed

300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

Preparation of new or previously untreated wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including laying of 15 mm thick screed bed or bedding layer in CM 1: 6 complete including dismantling of existing floor tiling and removing rubbish off the premises complete all as specified and directed

Non skid ceramic coloured jointless tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including laying of 15 mm thick screed bed or bedding layer in CM 1:6 complete including dismantling of existing floor tiling and removing rubbish off the premises complete all as specified and directed.

Glazed ceramic coloured tiles of size 300 mm x 200 mm x 7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with tile and including 10 mm thick rendering in cement mortar 1:6 finished rough surface to receive tiles including dismantling of existing wall tiling and removing rubbish off the premises complete all as specified and directed.

Machine cut Kota stone slab flooring 20-22 mm thick laid over and including 20mm screed bed in CM 1:4 laid and jointed with grey cement slurry, mixed with pigment to match the shade of slab including grinding,rubbing and polishing mirror finish and dismantling of the existing kota stone flooring of any description etc complete all as specified and directed.

Chequered cement concrete coloured tiles 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment to match the shade of tiles over and including 15mm thick screed bed in CM 1:4 complete including dismantling of existing tiles of any description complete all as specified and directed

MS work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and directed

Machine pressed precast coloured concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade laid, jointed and pointed in grey cement with pigment to match the shade of tile with and including 25mm thick sand cushioning layer including dismantling of existing damaged tile flooring etc complete all as specified and directed.

PCC 1:2:4 Type B-1 {using 20mm graded crushed stone aggregate} as in coping/benching bed plates including weathering, slightly rounded or chamfered angles and throating etc including necessary form work including demolition of existing cement concrete of any description complete all as specified and directed.

40mm thick PCC type B-1 1:2:4 (with using 20mm graded stone aggregate) as in flooring and finishing the surfaces even and smooth using extra cement complete including demolition of concrete complete all as specified and directed

PVC low level flushing cistern 10 Ltr capacity symphonic action type white including ball valve, float valve and handle including bracket and PVC flush pipe fixed in repair complete all as specified and directed

Vitreous china wash down water closet pan (pedestal pattern) white including seat cover of plastic, CP jet and pipe etc complete including necessary PVC pipe fittings fixed in repair complete all as specified and directed

Vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests including concrete bedding and making good existing floor fixed in repair complete all as specified and directed

PVC conections 15mm size with PTMT nuts of 450 mm long fixed in repair complete all as specified and directed

PVC conections 15mm size with PTMT nuts of 600 mm long fixed in repair complete all as specified and directed

15mm bore stop valve chromium plated male end screwed both end for iron pipe fixed in repair complete all as specified and directed. Make- Jaguar ESSCO cat part No MQT-513AKN or equivalent of cera/Hindware

Walling of random, rubble brought upto courses stone masonary, well bonded bedded and soilidly hearted and built in cement mortar (1:6) with and including P:C:C through bond stone in cement concreate 1:3:6 type C1 using 20 mm graded stone aggregate complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone with max depression on face from straight edge held against the dressed surface not exc 20mm and dressing of face and joints as specified of random rubble walling uncoursed or brought upto coursed of lime or sand stone all as specfied and directed.

15mm bore long body bib tap chromium plated with wall flange and aerator fixed in repair complete all as specified and directed. Make- ESSCO (Jaguar) cat part No MQT-512KN or equivalent of Cera/Hindware

Vitreous china wash basin, white, flat back, size 550x400mm including bracket, PVC waste pipe, CI grading fixed in repair complete all as specified and directed.

15mm dia pillar taps, rocket type with aerator fixed in repair complete all as specified and directed. Make- Jaguar Cat part No MQT-507KN or equivalent of Cera/Hindware

110mm dia PVC (SWR) sanitary short connection socket to fit WC outlet fixed in repair complete all as specified and directed

PVC (SWR) bends 75 mm dia any radius fixed in repair complete all as specified and directed.

PVC (SWR) bends 110 mm dia any radius fixed in repair complete all as specified and directed.

Continous (piano ) hinges mild steel bright finish or elctrogalvanised width of flape (when open ) 30mm complete all as specified and directed.

Continous (piano ) hinges mild steel bright finish or elctrogalvanised width of flape (when open ) 30mm fixed in repair complete all as specified and directed.

1000 Litres capacity rotational moulded polyethylene water storage tanks, three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including 20mm dia GI light grade washout pipe 50mm long with plug and 20mm dia GI light grade over flow pipe 600mm long with fitting including dismantling of existing unserviceable tank and removing from site complete all as specified and directed

500 Litres capacity rotational moulded polyethylene water storage tanks, three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including 20mm dia GI light grade washout pipe 50mm long with plug and 20mm dia GI light grade over flow pipe 600mm long with fitting including dismantling of existing unserviceable tank and removing from site complete all as specified and directed

15mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 142 gm) complete all as specified and directed.

20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gm) complete all as specified and directed

15mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 142 gm) fixed in repair complete all as specified and directed.

20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gm) fixed in repair complete all as specified and directed

PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, fixed to walls/floors fixed in repair complete all as specified and directed.

Door closer hydraulically regulated designation No 2 ,universal type suitable for door shuters of 701 to 850mm inwidth and of weight between 36 to 60 kg fixed as in repair complete all as specified and directed.

PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in surface channels and drains including demolition and taking out of existing cement concrete of any description complete all as specified and directed.

Preparation of old painted wooden surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed

Preparation of old painted steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed

Complete removal of existing treatment on old decorated surfaces (plastered/un-plastered) of walls including cornices and making good surface by applying a coat of 1.5 mm thick Birla/JK Putty complete all as specified and directed.

Preparation of new or old plastered surfaces of walls Facia, Chhajas and applying two coat of Appex or weather proof paint over a coat of primer complete all as specified and directed

Preparation of new or old plastered surfaces of wall and applying two coat of oil emulsion distemper over a coat of primer complete all as specified and directed

Forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed

4mm thick E-board false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605 X 605mm fixed with 1:6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework by means of 4mm dia adjustable "J" hook consisting of two Nos washers and two nuts at 1.2 mtr centres, size of main tee 38mm X 25mmX 1.4mm, cross tee 38 mm X 25 mm X 1.4mm, angle along walls 38 mm X 25mm X 2.0 mm and including taking down existing boards any thickness including cover fillets etc complete all as directed

Drapery rod in any length, high strength MS pipe with corrugated wooden finished having outer dia 28mm with plastic ring of ABS plastic of dia 56 to 58mm, a pair of brackets, fixed in repair complete all as specified and directed

Decorative finals ABS plastic in matching colour of wooden finished of same colour of rod fixed in repairs complete all as dierected.

Brass chromium plated towel rail 600mm long fixed in repair complete all as directed. Make : ESSCO (Jaquar) Cat No. AEC-1111 or equivalent of make Cera/Hindware

6mm thick cement corrugated or semi corrugated sheet in roofs fixed in repair wdith L or J type bolt including dismantlingt existing sheets complete all as specified and directed.

2nd class hard wood as in scantling clean swan fixed with nails complete including dismantling existing timber scantlings 40 sqcm and over in section in any position etc complete all as specified and directed

Pre- painted galvalume aluminium Zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding ridges to wall, fixed with self tapping screws etc complete including dismantling existing sheeting any type, gauge, thickness etc complete all as specified and directed

Pre- painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete including dismantling existing sheeting any type, gauge, thickness etc complete all as specified and directed

Regular modified polyester colour coated galvanized tile profile 0.5mm thick inclusive of protective coating as in roof fixed to steel member / wooden member with self drilling zincolium coated metal screws having cap with rubber and metal washer including dismantling of corrugaed AC/fiber sheet any pattern in roof including ridge complete all as specified and directed.

Keyed painting to random rubble masonary uncoursed or brought upto course in CM1:4 complete all as specified and directed.

0.63 mm thick galvanised corrugated mild steel sheeting with two corrugation side lap fixed with L or J type hooks and washer as in roof, wall etc with grade of zinc coating 120 complete including dismantling existing sheets all as directed.

0.80mm thick plain galvanized mild steel sheeting with grade of Zinc coating 120 fixed with "L"or "J" type hooks and washer as in ridges, hips, valley gutter etc including dismantling old sheets in ridges, hips valley gutter any pattern etc complete all as specified and directed

2nd class hard wood, plain fillet, bullnosed, splayed, chamfered or rounded on one edge, clean sawn, secured with nails, sectional area exc 3 sqcm but n.exc 6 sqcm complete fixed in repair complete all as specified and directed

Glass dividing strips 3mm thick and 38mm wide inserted in position and confirming to design complete all as specified and directed

Precast RCC 1:2:4 Type B-1( using 20 mm graded crushed stone aggregate} as in cover slab, set and jointed in CM 1:4 incl demolition of existing old RCC slabs of any description complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately under respective items of this BOQ)

Mild steel bars 08 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanized wire staples in repairs complete all as specified.

4mm thick cement building boards fixed in ceiling to timber framework with screws including all accessaries and including dismantling existing boards any thickness including cover fillets etc complete all as specified and directed

Sink made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter on to dwarf wall or inclulding fixing cantilver brackets and connecting union to pipe overall size 405mm x 460mm x 203 mm bowl size 405 mm x354mm x 203mm fixed in repair complete all as specified and directed. Make :- Make:- Prayag Cat part No.1216DM or equivalent in Blue star/Nirali.

Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter on to dwarf wall or inclulding fixing cantilver brackets and connecting union to pipe overall size 914 mm x 460x 203 mm bowl size 405 mm x 354 mm x 203mm complete all as specified and directed. Make :- Make:- Prayag Cat part No.1239DM or equivalent in Blue star/Nirali.

18 mm prelaminated PVC board interiror grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber / steel frame work as in cupboard shelves fixed in repair complete all as specified and directed

18 mm prelaminated PVC board interiror grade prelaminated both side with decorative choice lamination and fixed with screw to timber / steel frame work fixed in repair complete all as specified and

18mm thick partical board for insulation purpose fixed with nails to timber frame work including dismantling exsisting board complete all as specified and directed.

Vitreous china bowl urinal flate back size 430 x 370 x 340 mm with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1.2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixed in repair complete all as specified and directed

Vitreous china urinal, half stall type white with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1.2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixed in repair complete all as specified and directed

30mm thick flush shutters, solid core construction, with blockboard core and plywood panels, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Steel window factory made with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded Drg No TD-032 sh 1/10 to 10/10 complete all as specified and directed.

Steel window factory made with side hung shutter including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded Drg No TD-032 sh 1/10 to 10/10 complete all as specified and directed.

Steel ventilators with top hung shutter including hinges, steel peg stay Drg No TD-032 sh 1/10 to 10/10 complete all as specified and directed.

Vitrified ceramic jointless tiles light shade 10 mm thick (square/ rectangular) polished, area of each tile exc 0.18 Sqm but not exceeding 0.36 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:4 and dismantling of existing floor tiling and removing rubbish off the premises complete all as directed.

Vitrified ceramic jointless tiles Light shade 10 mm thick (square/ rectangular) polished, cut to size as required, as in vertical surfaces such as dado, skirting, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 10 mm thick rendering in cement mortar 1:4 finished rough to receive tiles including dismantling of existing wall tiling and removing rubbish off the premises complete specified and directed.

Glazed ceramic coloured joint free tiles of size 450x300mm x 7mm thick as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tile with and including 10 mm thick rendering in cement mortar 1:3 finished rough to receive tiles including dismantling of existing wall tiling and removing rubbish off the premises complete all as specified and directed.

Solid PVC wall lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and Drawing in SSR fixed in repair complete all as specified and directed.

5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing in repairs on to wall to make PVC frame as per specification and drawing in SSR complete all as specified and directed.

Powder coated aluminium anodised door with frame and shutter and glazing 5mm thick glass and 12mm thick prelaminted particle board exterior grade in bottom panel (kit ply, novapan) glass fixed with rubber gasket with aluminium galzing clips, section of aluminium door shall be of following size :- Frame ; 100 x 44 x 1.98 mm glass thickness with rawal plug. Middle lock rail ; 150 x 44 x 1.98mm thick, Bottom rail ; 150 x 44 x 1.98mm thick, Top rail/Style : 85 x 44 x 1.98mm thick, Glazing beading : 0.70 mm thick , Aluminium handle `D' type 150mm, Aluminium tower bolt 9.9mm dia shoot 200mm long, Mortice lock - 100 mm 4 lever, aluminium stooper cleat - 02 Nos including taking down existing doors etc and making good of wall complete all as specified and directed.

Powder coated aluminium anodised windows/ventilators with side hung shutter and frame made with aluminium section with and including glass (as specified below) Aluminium section shall be of size:- Frame 47 x 44mm x 1.98mm thick, Top/bottom and side style/rails of Shutter - 44 x 47mm x 1.98mm thick, Glass : 5mm thick tinted glass fixed with rubber gasket with aluminium beading. Aluminium fitting such as peg stay, aluminium hinges, aluminium handle 100mm long, aluminium tower bolt 100mm long and including taking down existing and making good of wall surface with matching to existing surfaces complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty fixed in repair complete all as specified and directed.

Granting doom 125 mm dia with waste hole of PTMT (minimum weight 40 gms) fixed in repair complete all as specified and directed.

15mm Chromium plated basin mixer with U shaped round casted spot with 450mm long braided hoses fixed in repair complete all as directed. Make:- ESSCO (Jaguar) cat No MQT-516AKN or equivalent of Make cera/Hindware

15mm Chromium plated wall mixture with 115mm long bend pipe for connection to overhead shower (with bush and piston divertor fitting) with areator fixed in repair complete all as directed. Make :- ESSCO (Jaguar) cat No,MQT-517BKN or equivalent of Make cera/Hindware.

5.5 mm thick frosted glass panes and glazing with oil putty or fix in alumium door/ window complete all as specified and directed.

Push cock with wall flange size 25mm with plain KNOB fixed in repair complete all as specified and directed. Make- ESSCO (Jaguar) Cat part No- MVF-553 or equivalent of Cera/Hindware.

Grinding of existing mozaic / kota stone flooring including mirror polishing complete all as specified and directed.

Overhead Shower 125 mm dia Round shape single Flow (ABS body chrome plated with Gray face plate) with Rubit cleaning system complete all as specifie and directed. Make- ESSCO (Jaguar) Cat part No- EOS-542AJN or equivalent of Cera/Hindware

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners brass handles etc as specified in clause 10.24 of SSR Part -I errected in position and securing runners with holdfasts and brackets including taking down existing steel gate complete all as specified and directed.

Aluminium wardrobe hooks (single) 50 mm to 60mm fixed in repairs complete all as specified and directed.

Hasp and staple 125 mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed in repair with screws complete all as specified and directed.

Clean the surface of roofs, walls, corner of window and door frame, slab and similar works by removing dust, loose particles, oil & grease to enusure the surface is clean, dry and sound and spread smart care hybrid polyurethan sealant in joint, cracks, and spread at edges to ensure adhension of sealant at both edges of joint/crack and then level the sealant with spatula/putty knife and finally finishing by tooling the surface with a concave shape with shop water complete all as per manufacturer instrcution and as directed. Make:- Asian paint product code no 5428 or equivelent of STP BERGER/Shalimar/Pidilite Industries Ltd/Structural Water Proofing Co Pvt Ltd/ Apar Infotech Pvt Ltd.

All as per per item No 131 here in before but sealant filling spreaded to cover holes of L/J hooks average dia 6-8 mm on CGI/PGI/Steel/AC roof sheet complete all as specified and directed. Make:- Asian paint product code no 5428 or equivelent of STP BERGER/Shalimar/Pidilite Industries Ltd/Structural Water Proofing Co Pvt Ltd/ Apar Infotech Pvt Ltd.

Rolled structural mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner grith in cement concrete, using extra cement, including forms, moulds, mi-tred/stopped ends etc complete all as specified and directed

Rendering 20 mm thick plaster on stone masonary surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

Demolition of cement concrete of any description and in any position complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

20mm bore gun matal gate valve male end screwed both end for iron pipe fixed in repair complete all as specified and directed.

15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs.

Disconnecting existing tank of any description, setting aside (or lowering if required) for cleaning and removing all Scale dirt etc and from mouths of circulating pipes including washing with bleaching powder etc and hosting, reconnecting and re fixing in position of capacity exc 500 ltr but n exc 1000 ltr complete all as specified and directed.

Disconnecting existing tank of any description, setting aside (or lowering if required) for cleaning and removing all Scale dirt etc and from mouths of circulating pipes including washing with bleaching powder etc and hosting, reconnecting and re fixing in position of capacity exc 250 ltr but n exc 500 ltr complete all as specified and directed.

Preparing of new steel surfaces over 10 cm width and girth and applying two coat of synthetic enamel over a coat of red primer complete all as directed.

5mm thick sheet glass ordinary quality in square n exc 0.50 sqm each pane, glazed with oil putty or fixed with wooden bead complete all as specified and directed

4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m each pane complete all as specified and directed

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and.exc 1.5m and n exs 3.00 m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and directed..

150 mm bore, salt glazed stone were (SGSW) drain pipe, grade 'A', laid to slope in tranches and jointed in cement mortar 1:1 including necessary testing including demolition and breaking up drain complete all as specified and directed.

PCC 1:4 ;8 type D-2 using 40mm graded crushed stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested suitable for 150mm bore of pipe complete all as directed.

200 mm bore, salt glazed stone were (SGSW) drain pipe, grade 'A', laid to slope in tranches and jointed in cement mortar 1:1 including necessary testing including demolition and breaking up drain pipe complete all as specified and directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested suitable for 200mm bore of pipe complete all as directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested suitable for 300mm bore of pipe complete all as directed.

300 mm bore, reinforced concrete pipe class NP-3 laid and jointed with collars laid to slope in tranches and jointed in cement mortar 1:1 including necessary testing including demolition of existing pipe complete all as specified and directed.

Construction of soakage well of size 3.60 M dia X 3.00 M deep, excavation in any type of soil, foundation in PCC 1:3:6 type C-2, walls of honey combed and solid in M-25 (design mix) concrete, including intercepting chamber, screen chamber, brick work in CM 1:4, plaster where shown on drg shall be 12mm thick in CM 1:6, bearing plaster 15mm thick in CM 1:4, RCC cover slab In M-25, filling with brick bats of gauge 80 to 150mm complete all as specified and shown Drg TD-309 sheet 1/4 to 4/4

Cutting into existing manholes for connecting new drains of 150 mm internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

Cleaning the sewage line up to 150mm dia by rodding manually and removing the sludge and completely cleaning by flushing with water etc complete , sludge shall be buried into ground and throwing the enough quanity of lime to stop the foul smell complete all as specified and directed.

Cleaning the sewage line over 150mm dia and upto 250mm dia by rodding manually and removing the sludge and completely cleaning by flushing with water etc complete , sludge shall be buried into ground and throwing the enough quanity of lime to stop the foul smell complete all as specified and directed. Note:(Quated Rates are including with one helper to trade man)

Dewatering of septic tank and draining out the water and burrying the water into the ground including throwing of required quanity of lime to stop the foul smell complete all as specified and directed.

Desludging/cleaning of septic tank /soakage well of any depth by mechanically means or by pumping and burrying the sludge into the ground pit , covering the pit with earth and finally spraying unslaked lime over the pit including throwing of required quantity of lime to stop the bad smell complete all as specified and directed. Note:-(i) cost of the pit is deemed to be included in the unit rate quoted by the tendered (ii) Rates quoted by the contractor for this item are for solid contents of sludge only (The volume of solid contents of sludge shall be calculated by reducing 50% of loose/separated quantities of sludge)

Cleaning blockage of WC ,gully trap, floor trap etc upto Ist manhole by rodding manually and removing the sludge cleaning by flushing with water etc complete , all as per site requirement all as specified and directed.

Dismantling posts or struts ( wood ,steel or RCC) any section including taking out embedded portion and making good disturbed natural ground complete all as specified and directed.

Dismantling fencing wiremesh any type and any description complete all as specified and directed.

Pre-cast RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in column ,pillars, piers,posts and struts complete all as specified and directed.

Mild Steel work as in posts and struts in fencing including cutting tops to shape as directed drilling holes notching bfor wires etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting and riveting etc complete all as directed.

Supply and fixing MS galvanised chain link fencing, of size 4mm dia and mesh size 100x100mm to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Galvanized 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc fixed in repair complete all as specified and directed. (Each line wire to be measured)

Restaining, resecuring of galvanized 2 strand steel barbed wire with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining boths, including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc including making good staples etc complete all as specified and directed. (Each line wire to be measured)

Mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel screw bolts 5 to 10 mm dia (machine made ) with hexagonal or squre head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or squre nuts exc 5 cm but n exc 10 cm long complete all as specified and directed.

Milled steel framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles, as necessary gusset plates riveting etc exc 10 kg each bracket over 10 kg each to be measured under Structual steel complete all as specified and directed

M/S RAJESH KUMAR GOYAL

Alankar Traders

Aggrawal Builders and Furnishers

M/s caspur construction company