Special repairs to CPO Md Accn Bldg No. P-206 at INS Valsura, Jamnagar

Taking down cement plaster of any description on PCC/stone surface/brick surfaces including raking out joints, hacking for key scrubbing down with water etc and removal of entire debris as ordered outside MoD land complete all as specified and as directed.

Demolition of brickwork/PCC block or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of entire debris as ordered outside MoD land complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for in this Schedule and removal of entire debris as ordered outside MoD land complete all as directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to faciliate demolition) including removal of entire debris as ordered outside MoD land complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule (BOQ), complete all as specified and as directed.

Dismantling of Fibre sheets (corrugated, semi corrugated or plain) etc any thickness including ridges as in roof covering and removal of debris to outside MoD land and depositing where directed including necessary scaffolding, safety net, safety belt, etc complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, including removal of entire debris as ordered outside MoD land complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MoD land complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down chowkat or frame with shutters (including grills, fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for PCC 1:5:10 type E2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete for sunken portion complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in roof kerbs, mud stops, coved fillets, padding over roof, cills, steps, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

Supply only Liquid Water Proofing Compound (ISI Marked).

M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified and as directed.

M&L for cutting holes into or through brick / PCC block / stone masonry wall built in cement mortar and making good in cement mortar 1:3 or PCC 1:2:4 type B0 as required for superficial area exc 150 sqcm but not exc 400 sqcm and 15 to 20 cm of depth (of cutting), complete all as specified and as directed.

M&L for cutting holes in brick/stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as required including making good as per its original specification without any extra cost, not exc. half brick thick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall).

Cutting chases in brick/ stone wall, pinning in, making good to facing where required and plastering in CM 1:4 to ends of edges of landing, steps, cills, lintels etc and cutting chases not exceeding 10 cm girth for concealed water tubing and similar works and making good cutting as per its original specfication complete all as directed.

S&F Second class hard wood kiln seasoned, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixed in position complete all as specified and as directed.

S&F factory made 35 mm thick second class hard wood plain framed panelled door shutter (any number of panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12mm thick veneered particle boards with commercial veneering on both face the size of rail and style as per IS - 1003 (Part I) kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified and as directed.

S&F factory made 35 mm thick second class hard wood glazed and skeleton door shutter open rebated and prepared to receive glass, guage etc edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a), kiln seasoned and chemically pressure treated, supplied and fitted to chowkats, complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window / Ceosetory windows & other Frames/ Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/sqmm, modules of elasticity 900 N/sqmm and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: MS hold fast/ lugs/ SS dash fasteners shall be measured and paid for separately.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/sqmm, modulus of elasticity 850 N/sqmm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer -In- Charge. Note: Stainless steel butt hinges and necessary SS screws shall be measured and paid for separately.

S&F 150 mm long aluminium, anodised, barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 100 mm size stainless steel butt hinges (ISI Marked), medium weight.

S&F 150 mm size extruded aluminium alloy handle (ISI Marked), cast type, anodised and fixed complete all as specified & as directed.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flaps (when open) 40 mm fixed with CP steel screws complete all as specified and as directed.

S&F mild steel 300mm ordinary rat tail rod pattern spring including roller and roller plate, complete all as specified & as directed.

S&F 100mm hasp and staple, stainless steel, including bolts to hinge plate and fixed with screws complete all as specified and as directed.

S&F Stainless steel Magnetic catcher with striking plate fixed with screws, conforming to the sample kept in GE’s office, complete all as specified and as directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples along with wooden beads complete all as specified and as directed.

S&F in repairs stainless steel drapery rod of 25mm dia (in lengths as directed) with & including stainless steel decorative SS bulb type finial at both ends / SS end socket and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws (65mm long) on walls/beam complete all as specified & as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, framed signed boards, walk ways, railings, framework of water tanks and similar work including welding conforming to Fe.290 (Gde E-165), complete all as specified & as directed.

S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, steel ladders etc fixed with angle cleats or other connecting plates etc conforming to Fe-410-W (Gde E-250) quality 'A’ complete all as specified and as directed.

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F aluminium powder coated (minimum thickness of powder coating 50 micron) frames for doors, windows and ventilators with one or more rebates including joining cleat for fixing, powder coated aluminium snap on beading, neoprene gasket etc. complete all as specified and as directed.

S&F aluminium powder coated (minimum thickness of powder coating 50 micron) window and ventilator shutter, side hung type without sash bar, aluminium section weighting 0.90 kg/m including necessary jointing cleats, louvers, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos.), suitable handle (2 Nos.) etc. complete all as specified and as directed. Note: Glass/Wire mesh shall be measured and paid for seperately.

S&F 80mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed. Note :- Door stopper shall be conforming to the sample kept in GE’s office.

S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified & as directed.

M&L for cutting out cracks to 'V' section in existing roofs or terrace cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified & as directed.

Material and labour for complete removal of existing water proofing treatment of any description or any other type of treatment over roof slab, parapets, chimney stacks, etc including cement plaster over RCC roof and cleaning the surface with wire brushes and washing with water, removing of insolvent materials and removing & depositing the debris, rubbish, etc outside MoD land, brushing neat cement slurry @ 3 Kg of cement per Sqm over the cleaned surface and provide 15mm thick screed bed/bedding layer/plaster in CM 1:3 mixed with integral Water Proofing Compound (WPC) as per manufacturer's instructions and finishing the surface even & smooth without using extra cement while the cement slurry is still green on RCC roof/parapet, provide oil bound bituminous primer @ 0.30 Kg/Sqm after bedding layer/plaster is cured with water for 7 days & completely dried, provide minimum 4mm thick APP based modified polymeric water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyester matt fabric weighing not less than 160 gms/Sqm with over laps 100 mm longitudinal direction (side laps) and 150 mm on the transverse direction (end laps) by thermo-fused torch flame application method as per detailed procedure as directed and finally finishing the top surface with one finishing coat of bituminous aluminium paint complete all as specified and as directed. Notes: (i) WPC shall be measured & paid for separately as ‘Supply only’. (ii) The work shall be carried out only through manufacturer or their authorised applicator and contractor shall submit a written guarantee of the manufacturer/authorised applicator for the effectiveness of WPT for 10 years from the date of completion of contract. (iii) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (iv) The net area of water proofing treatment shall be measured without any extra allowance for laps.

M&L for rounding to edges of stone slabs (one edge), 18 to 20mm thick stone as in steps, cooking platform and other similar situations, including machine polishing to edge to give high gloss finish etc., complete all as specified and as directed.

M&L for average 25mm thick plain cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in floor, levelling course, etc by maintaining gradient/ undulation, finished fair & even complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40 mm graded crushed stone aggregate) as in sub-floors, sub-bases, floors and pavings, etc finished fair and even complete all as specified & as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces of wall mixed with integral liquid water proofing compound as per manufacturer’s instructions and finished the surface even and smooth without using extra cement complete all as specified and as directed. Note : Liquid WPC shall be measured and paid for separately as 'Supply only'.

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick layer of white cement based wall care putty complete all as specified & as directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white cement based wall care putty complete all as specified & as directed.

M&L for complete removal of existing treatment by mechanical means (any number of layers) by hand held sander/ long handle sander, including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces of wall and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white cement based wall care putty on walls complete all as specified & as directed.

M&L for complete removal of existing treatment by mechanical means (any number of layers) by hand held sander/ long handle sander, including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces of ceiling and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white cement based wall care putty on ceiling complete all as specified & as directed.

M&L for preparing newly plastered surface of walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm as per manufacturer's instructions complete all as specified and as directed.

M&L for complete removal of existing treatment by mechanical means (any number of layers) by hand held sander/ long handle sander, rubbing down, stopping of distempered & Jet pressure washing and painted surface of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm as per manufacturer's instructions complete all as specified and as directed.

S&F 4mm thick tinted sheet glass, ordinary quality and glazing with oil putty or wooden beads or fixed to aluminium sections not exceeding 0.5 Sqm in each pane complete all as specified & as directed.

S&F 4mm thick tinted sheet glass, ordinary quality and glazing with oil putty or wooden beads or fixed to aluminium sections exceeding 0.5 Sqm in each pane complete all as specified & as directed.

S&F 4mm thick figured glass, pin headed type and glazing with oil putty or wooden beads or fixed to aluminium sections not exceeding 0.5 Sqm in each pane complete all as specified & as directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of 1st quality synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of 1st quality synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of 1st quality synthetic enamel paint of approved tint complete all as specified & as directed.

Taking up or down 20 mm bore GI tubing and connection, including cleaning for re-fixing stacking at site where directed.

Taking up or down old 25 mm bore GI tubing and connection, including cleaning for re-fixing stacking at site where directed.

Taking up or down old 32 mm bore GI tubing and connection, including cleaning for re-fixing stacking at site where directed.

M&L for galvanized steel water tubing medium grade of 25mm bore (ISI marked) with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supplying and laying of 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, elbows, unions, end pieces, etc and fixed with solvent cement fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Supplying and laying of 32mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, elbows, unions, end pieces, etc and fixed with solvent cement fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F in repairs 32mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

S&F in repairs 15mm bore bib tap with wall flange, fancy type, cast copper alloy, long body, chromium plated screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. 7508 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore two way bib tap fancy type, brass, chromium plated with flange and aerator, screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. 7512 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs Health Faucet brass chromium plated with 1.2 mtr SS Chrome plated EPDM tube & ABS hook wall mounted type complete all as specified and as directed. Make: Prayag Cat No. BEA-85 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs concealed type stop valve with wall flange 15 mm bore of pipe, brass chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make: Prayag Cat No PIS-18 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs chromium plated 110mm square over head ABS shower with SS Arms & Flange, swivel joints fixing to steel pipes etc complete all as directed. Make : Prayag Cat No BS-72N or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore brass, chromium plated, sink mixer wall mounted with 170mm long swivel spout, connecting legs and wall fange, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. Make: Prayag Cat No. 7555 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore, brass, chromium plated, wall mixer with L bend with wall flange and one for shower rose, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe complete all as directed. Make: Prayag Cat No. 6875 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore, brass, chromium plated, single lever basin mixer W/O pop up waste system for hot and cold water mixing, screwed for iron pipe complete all as directed. Make: Prayag Cat No. 7851-N or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repair CP brass soap dish including fixing with brass screws complete all as specified & as directed. Make : Prayag Cat No BA-05 or equivalent in makes mentioned in Appendix 'B' here-in-after

S&F in repairs stainless steel Peg Set of Six of standard size (not less than 300mm long) fixed to wall with two rawl plugs and chromium plated brass screws complete all as specified & as directed. Make :- Cat Part No BEA-30 of make – Prayag or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make : Prayag Cat No BA-40 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (Minimum weight 90gms) complete all as specified & as directed.

S&F in repairs stainless steel grating square shape of size 140mm with openable round dome of 75mm dia and fixed complete all as specified & as directed.

S&F in repairs PVC connections 15mm dia, 600mm long with PTMT nuts & washers at both ends.

S&F 32 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2, fixed to walls, ceilings or in floors etc. complete as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in floors/ fixed to walls, complete all as specified & as directed.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in floors/ fixed to walls, complete all as specified & as directed.

S&F 75 mm bore PVC (SWR) bends any radius including jointing the same with solvent cement complete all as specified & as directed.

S&F 110 mm bore PVC (SWR) bends any radius including jointing the same with solvent cement complete all as specified & as directed.

S&F 75mm bore PVC (SWR) junction single (single T) equal or unequal with access door including jointing the same with solvent cement complete all as specified & as directed.

S&F 110mm bore PVC (SWR) junction single (single T) equal or unequal with access door including jointing the same with solvent cement complete all as specified & as directed.

S&F PVC (SWR) Vent cowl 75mm bore size fixed complete all as directed.

S&F PVC (SWR) Vent cowl 110mm bore size fixed complete all as directed.

S&F in repairs PVC (SWR) floor trap plain including jointing with solvent cement, diameter of outlet 75mm, complete all as specified & as directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 600mm x 480mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm/ suitable fastener bolts, with & including 32 mm dia CP brass bottle trap and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & as directed.

S&F in repairs 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and flush pipe of polyetylene of low or high density or 32 mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with aluminium alloy brackets and guard rail 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as specified and as directed.

S&F in repairs bathroom cabinet mirror (400x500mm) including fixing screws complete all as specified and as directed. Make: Prayag Cat No. 554 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs corrosion resistant Stainless Steel Kitchen plate rack of size 31x30x10 inch, with 0.80 mm thick Stainless Steel sheet (minimum weight 7.00 Kg) fixed to walls with rawl plug and brass screws, complete all as specified and as directed.

S&F sink without draining board, glossy finished, made out of 1.00 mm thick stainless steel sheet for kitchen or laboratory with plug, washers and waste pipe, including bedding in CM to dwarf wall or including fixing cantilever, brackets and connecting union to pipe, overall size 495x420 mm with bowl size 410x330x160 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings.

Dismantling of existing any type & any capacity water storage tank fixed in any description and S&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover hoisted and fixed in position where ordered and making necessary connections for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

M&L for preparation of the surfaces of existing sunken floor thoroughly to have a sound base and application of two components acrylic polymer modified cementitious flexible waterproof coating with Brushbond Master Seal 550 (BASF)/ Brushbond (Fosroc)/ Pidifin 2K (Dr. Fixit) or equivalent in other makes of 1mm thickness. The coatings shall be applied at intervals and as per manufacturer's specifications. Providing Base Coat 20mm thick plastering in the CM 1:3 mixed with approved water proofing compound like Master pel 777 (BASF)/ Conplast WL (Fosroc)/ Pidiproof LW ( Dr. Fixit) or equivalent in other approved makes (Integral waterproofing compound confirming to IS 2645) for floor and walls. Providing Top Coat 20mm thick plastering in the CM 1:3 mixed with approved water proofing compound like Master pel 777 (BASF)/ Conplast WL (Fosroc)/ Pidiproof LW ( Dr. Fixit) or equivalent in other approved makes (Integral waterproofing compound confirming to IS 2645) for floor and walls. Providing and application Brushbond Coating of two components acrylic polymer modified cementitious flexible waterproof coating with brush bond Master Seal 550 (BASF)/ Brushbond (Fosroc)/ Pidfin 2K (Dr. Fixit) or equivalent in other approved makes of 1mm thickness. The coating shall be applied at intervals and as per the manufacturer's specifications.

M&L for Kitchen cabinet with shutter complete in required sizes made out of 18 mm thick PVC board with one side decorative and other side white balancing lamination fixed with screws and adhesive, SS screws of 5.5 mm size, fixed as per manufacturer’s instructions and standard trade practice, complete all as specified and as directed including taking down existing old Kitchen cabinet.

All same as per serial item No. 112 here-in-above, but both sides white lamination in CB shelves, partitions, sides, etc.

S&F 100mm long stainless steel designer handle (heavy duty) fixed to cupboard shutters with brass screws complete all as specified & as directed.

S&F stainless steel kitchen cabinet overlay/ L clip hinges complete all as specified and as directed.

S&F 60 cm long stainless steel telescopic channels for sliding modular Kitchen racks/ drawers. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern plain/ cutlery basket of size 18"x20"x8" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern Thali basket of size 18"x20"x8" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern plain/ cutlery basket of size 18"x20"x6" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern plain/ cutlery basket of size 18"x20"x4" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern cup and saucer basket of size 18"x20"x4" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern perforated cutlery basket of size 18"x20"x4" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

M&L for non shrink cementitious micro concrete (‘SikaRep Microcrete-4’ of Sika / ‘Renderoc RG’ of Fosroc or equivalent of Dr. Fixit/ Pidilite/ Asian) meeting ASTM C1107 standard in average thickness 60mm and having minimum compressive strength 50 N/sqmm after 28 days as per ASTM C109, for repair to column, beam, slab, etc, complete all as per manufacturer’s instructions complete all as directed. Notes : (i) Formwork shall be measured and paid for separately. (ii) Reinforcement shall be measured and paid for separately.

Providing, fixing and removing of water tight shuttering (Form work) using film coated 12mm thick plywood sheets for micro-concreting the lintels/ beams/ slabs in line and level and with proper support of average thickness 50-75mm including scaffolding and all safery measures of labourers complete all as specified and directed. Note : Formwork under this item shall be measured and paid only for repair of RCC members with micro concrete.

M&L providing additional reinforcement TMT bars in place of more than 1/3 corroded reinforcement bars including cutting, bending, placing and fixing in position using 'Lokfix' of M/s Fosroc or equivalent of Dr. Fixit / SIKA / Pidilite/ Asian with & including all necessary tools, scaffolding, etc. complete all as specified and as directed. Note : Weight of TMT bars shall only be measured for payment purpose.

E&M Items: Taking down carefully existing unserviceable/perished surface conduit/concealed conduit/batten/casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/conduit/casing caping, etc and making good the disturbed surfaces of wall, floors, ceiling, etc to match with the adjoining surfaces, complete all as specified and as directed.

All as per serial item No. 128 here-in-before but for one 3 pin 5/6 Amp modular switch socket on same board with other switches.

All as per serial item No. 128 here-in-before but for one 3 pin 5/6 Amp modular switch socket on independent board.

All as per serial item No. 128 here-in-before but for one 16 Amp and 6 Amp (3 pin) combined, modular switch socket on independent board with 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour.

S&F in repairs modular switch, single pole, one way, 6 Amp, 1 module with all accessories complete all as directed.

S&F in repairs modular switch, single pole, one way, 16 Amp, 1 module with all accessories complete all as directed.

S&F in repairs modular switch 2 way, 6 Amp, 1 module with all accessories complete all as directed.

S&F in repairs modular socket 6 Amp, 2/3 pin combined, 2 module with all accessories complete all as directed.

S&F in repairs modular socket multipurpose 6 / 16 Amp - 2/3 pin combined, 2 module with all accessories complete all as directed.

S&F in repairs modular bell push 6A, one way, 1 module with all accessories complete all as directed.

S&F in repairs bell, Ding Dong/Multi music type, 240 Volt AC supply complete all as directed.

S&F in repairs modular type TV socket outlet modular type, 1 module complete.

S&F in repairs modular type RJ 11 Telephone socket, 1 module complete.

S&F in repairs 20 mm dia rigid non-metallic PVC conduit (heavy duty, ISI marked) exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends, etc and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed.

M&L for metal flush boxes concealed for mounting TV /Telephone socket etc including logic modular plates and surrounds of suitable size including dismantling existing box.

S&F in repairs ceiling rose surface bakelite White/ Ivory/ Urea finish 50mm dia three terminals including PVC square mounting block & electric wiring connection complete all as specified and as directed.

Taking down existing batten type light fitting of any description & fixed in any position and S&F new clear white 20 Watt wall mounted 4 ft LED batten type decorative light fitting, minimum CCT 5700K, 230 Volts, 50 Hz, extruded aluminium housing & polycarbonate diffuser, fixed as per manufacturer's instructions and making necessary electrical connections and testing on completion complete all as specified and as directed.

Taking down existing batten type light fitting of any description & fixed in any position and S&F new clear white 10 Watt wall mounted 2 ft LED batten type decorative light fitting, minimum CCT 5700K, 230 Volts, 50 Hz, extruded aluminium housing & polycarbonate diffuser, fixed as per manufacturer's instructions and making necessary electrical connections and testing on completion complete all as specified and as directed.

Taking down existing street/ security light fitting of any type & fixed in any position and S&F new 45 Watt LED street/ security light fitting, High Efficiency, minimum IP 65 protection, CCT - 5700K, system lumen efficacy ≥ 110 Lm/W, Power factor ≥ 0.95, powder coated pressure die cast aluminium housing, top opening with separate driver compartment and clear PMMA/polycarbonate/toughened glass heat resistant cover, fixed on walls or steel/concrete pole at any height including making connection from ceiling rose/ Junction Box to light fitting with and including three core 1.5 Sqmm cable multistranded copper conductor PVC insulated & PVC sheathed, 1100 V grade of required length fixed as per manufacturer's instructions and making necessary electrical connections and testing on completion, fixed over & including mounting bracket made of 32mm bore GI pipe ‘light grade’ not less than 1.20m long, bent to shape at required angle, fixed to Pole/wall with & including mild steel clamps (02 Nos) made out of flat iron 50x6mm with nuts, bolts & washers, complete all as specified and as directed.

S&F in repair modular step type fan regulator 120 W, 2 module, AC, 230V, electronic complete all as specified and as directed.

Carefully disconnecting electric & water connections and taking down existing serviceable Geyser (water storage type) of capacity 25 litre vertical type and re-fixing the same with & including new ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of suitable size but not less than 10mm dia 125mm long with nuts & washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original and re-connecting electric & water connections, complete all as directed.

S&F in repairs 15mm dia stainless steel braided connection tube, heavy duty of size 450 mm long with CP brass adopter/ union washer both sides suitable for hot & cold water supply for geyser complete all as specified and as directed.

S&F in repairs single pole and neutral enclosure with a two pin and earth plug and socket complete 240 V with one Single Pole MCB 20 Amps, 10 kA, 'C' Curve complete all as specified and as directed.

S&F in repairs Distribution Board (DB) sheet metal enclosure, SPN, 12 way with 100 Amps rated bus bar, double door, 240 Volts, suitable for fixing MCBs, fixed in concealed or on wall as per site requirement, complete all as specified and as directed.

S&F in repairs Distribution Board (DB) sheet metal enclosure, TPN, 4 way with 200 Amps rated bus bar, double door, 415 Volts, suitable for fixing MCBs, fixed in concealed or on wall as per site requirement, complete all as specified and as directed.

S&F in repairs MCB SP 6 to 32 Amp, 240 V, 50 Hz, AC supply, 10 kA, 'C' Curve, complete all as specified and as directed.

S&F in repairs MCB SPN 40 Amp, 240 V, 50 Hz, AC supply, 10 kA, 'C' Curve, complete all as specified and as directed.

S&F in repairs MCB TPN 63 Amp, 415 V, 50 Hz, AC supply, 10 kA 'C' Curve with proper size lugs complete all as directed.

Supply, laying, jointing and testing LT XLPE (cross linked polyethylene) insulated, screened, PVC bedded, galvanised steel strip or wire armoured electric cable (heavy duty) with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 Core (ISI marked) laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out old unserviceable cable complete all as specified & as directed. Note : Sand cushioning, cable protection covers, protection pipe, jointing kits and excavation & earth work shall be measured & paid for separately.

M&L for filling approved dry river sand for cushioning and cover for protection of under ground electric cable in trenches 8 cm before laying cable and 15 cm deep over the cable and punning to 18 cm total thickness complete all as specified and as directed. Notes :- (i) Approved dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment, only punned thickness shall be measured.

Taking down old existing unserviceable LT PCC Cable Cover of any type/ size and Supply and laying new un-reinforced precast concrete cable cover, Class LV, Type-1, Flat, size 250mm x 150mm x 40mm for protection of underground electric cable in trenches complete all as specified and as directed.

M&L for Earthing with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected using galvanized iron earth lead wire 4 mm dia upto 7.5mtr as earthing lead by means of bolts, nuts, check nuts and washers of GI earth lead wire protected by Gl light grade pipe 15 mm bore, including provision of concrete earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover reinforced with 8 mm dia TMT bars reinforced at 100 mm C/C both ways and handle of 6 mm dia MS bar made to shape, GI medium grade 20 mm bore pipe for watering perforated at bottom, 2 m long placed on top edge of earth plate, charcoal and common salt filling test point made out of 40x8 mm flange with fixing arrangement, funnel, wire mesh and earth work in any type of soil, returning, filling in and removal of surplus soil to a distance not exceeding 50 m all as per electrical Plate No. 3 of SSR Part I and connected to earth test point including testing on completion complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing.

Taking down carefully and refixing the existing serviceable electric meter single/ three phase of any capacity or make, making all new electrical connections, complete all as directed by Engineer-in-Charge or as per site requirement.

S&F suitable size PVC/ Fiber electric meter box with viewing window/ glass for meter reading for equiped existing electric meter single phase including all required mounting arrangement on wall/ panel complete all as directed by Engineer-in-Charge.

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in trenches, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soil complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mts and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as directed.

M&L for post construction Anti Termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

S&F XPM design aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples along with wooden beads complete all as specified and as directed.

S&F GI Chicken wire mesh cut to size made to shape as ordered including fixed to walls with nails for receiving the plaster complete all as directed. Note : Weight of GI chicken wire mesh shall be 250 to 300 gm/Sqm.

M&L for writing letters or figures (Block, Roman, Italic or Indian) of size 5 to 8 cm high with thick synthetic enamel paint of approved tint over a synthetic enamel paint circle of 15 cm dia in approved tint for describing building numbers on concrete/plastered surfaces complete all as specified & as directed. Note : The font, style, matter, tint of paint & place of writing shall be as directed by the Engineer-in-Charge.

M&L for writing letters or figures (Block, Roman, Italic or Indian) of size 8 to 10 cm high with thick synthetic enamel paint of approved tint over a synthetic enamel paint circle of 30 cm dia in approved tint for describing building numbers on concrete/plastered surfaces complete all as specified & as directed. Note : The font, style, matter, tint of paint & place of writing shall be as directed by the Engineer-in-Charge.

Please Enable Macros to View BoQ information