Constt of Community Hall at Phalli Brahmana

Amount

Earthwork in excavation by mechanicall means in trenches for foundation ,over areas (exceeding 30cm up to 1.50m) in depth as well as 10m on plan including disposal of excavated earth up to 1 mtr. Form cutting edges and disposal of earth and level neatly dressing in 75% AKS, 20% ordinary rock and 5% hardrock.

Providing and Laying P.C.C in (1:5:10) mix with 20mm nominal crushed stone agg. Including all lead lift and carriages including loading, unloading stacking at site complete Job.

Providing and laying in position cement conc. Of specified grade excluding the cost of centering and shuttering all work up to plinth level (1:3:6) (1: cement:3 coarse sand:6 graded stone agg. 20 mm nominal size) Including all lead lift and carriages including loading, unloading stacking at site complete Job.

Supply and pacing of stones in Plumb Conc.

Providing /laying R.C.C in (1:1.5:3) mix with 20mm nominal size crushed stones aggregates excluding centering and Shuttering. Including all lead lift and carriages including loading, unloading stacking at site complete Job.

Centering and Shuttering of Ordinary Timber

Suspended floors, roofs, landing, balconies and access platform

Lintels, beams, plinth beams, griders, bressumers and cantilevers

Columns

Edge of slab

Reinforcement for RCC works including cutting, bending, binding and placing etc all complete.

Brickwork with bricks of class designation 75 above plinth level up to floor level in cement mortar (1:6)mix.Including all lead lift and carriages including loading, unloading stacking at site complete Job.

Providing and laying 1:2:4 mix flooring with the floating coat of neat cement including cement slurry with 20mm nominal size crushed stone agg.50mm thick. Including all lead lift and carriages including loading, unloading stacking at site complete Job.

12mm cement plaster of mix 1 cement:6 coarse sand Including all lead lift and carriages including loading, unloading stacking at site complete Job.

6 mm thick (1:3 mix)

Distempering with oil bond washable distemper of approved brand and manufacturer to give an even shade

White washing with lime to give an even shade on new work (three or more coats)

Finshing walls with water proofing cement paint of required shade on new work (two or more coats applied @ 3.84kgs/10sqm)

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60mm thickness, including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60mm pressed, mild steel welded or rigidly fixed together by mechanical means, including M.S pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing on wall face unplasticised-rigid PVC rain water pipe confirming to IS:13592 type-A including jointting with seal ring confirming to IS:5382 leaving 10mm gap for thermal expansion single socketed pipes 110mm diameter.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S pressed butt hinges bright finished of required size with necessary screw excluding panelling which will be paid for seprately , all complete as per direction of engineer-in-charge. Second class kail wood.

Providing and fixing glazed shutters for doors, windows, clerestory windows using 10kg/sqm (4mm thick) float glass panes including ISI marked M.S pressed butt hings bright finish of required size with necessary screws

Providing and fixing wire gauge shutters using galvanized M.S wire gauge of average width of aperture 1.4mm in both directions with wire of dia 0.63mm, for doors windows and clestory windows with hinges and necessary screws.

Providing and fixing M.S grills of grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.particle board 12mm thick.

Providing and fixing circular /hexagonal cast iron box for ceiling fan clamp of internal dia 140mm, 73mm height , top lid of 1.5mm thick MS sheet with its top surface hackedwith proper bonding, top lid shall be screwed into the cast iron MS sheet box by means of 3.3mm dia round headed screws one lock at the corner. Clamp shall be made of 12mm dia MS bar bent to shape as per standard.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete:100x10mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete: 100mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete: 125mm

Providing and fixing of electric points complete in all respect as per requirement of site, to be paid as per actual

Vinod Kumar Dutta