Mtc. of non-residential building at LTV Division PWD office during the year 2026-27

Takingout doors,windowsandclerestorywindow shutters(steelorwood) includingstackingwithin50 metres lead :14.10.1 Of area 3 sqm and below.

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete: 6.12.3 In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Providing woodwork in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed in position :8.1.3 Local Teak Wood

Providing and fixing panelled/or panelled and glazed shutters fordoors,windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and orglazing,which will be paid for separately but including the wooden beading of 20 ×12mm for fixing panelling and or glazing as per direction of Engineer-In-Charge.8.5.1 8.5.1 Local Teak wood 8.5.1.2 30 mm thick shutters

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board including\ providing and fixing of frame work made of special section power pressed/ role form G.I. sheet with zinc coating of grade 175 consisting of floor and ceilling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick fixed to the floor and ceilling at the spacing of 610 mm centre to centre with dash fastener of 12.50 mm dia-mater, 40 mm length and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceilling channel and placed at a spacing of 610 mm centre to centreb by 6 mm dia bolts and nuts at both ends of partition fixed flush to wall with rawl plugs at spacing 450 mm centre to centre and fixing of boards to either side of frame work by 25 mm drive all screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre, including jointing and finishing to a flush finish with recommended joiunting compound , jointing tape, joint finisher and two coats of primer siutable for boards asper manufacture's specification and direction of the Engineer-In-Charge all complete.. 8.103.1: 67mm overall thickness partition with 8.5 mm thick double skin Glass reinforced Gypsum (GRG) board conforming to IS: 2095: part III

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : 12.35.1:- New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sectionsand other sections of approved make c onforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling,C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer­in­charge. (Glazing and paneling and dashfasteners to be paid for separately) :-16.1.1:- For fixed portion of approved quality:-16.1.1.1:-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

:- For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- 16.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).