PROVISION OF POL STORE AT NEW MT POOL AND MES OFFICE COMPLEX HARD STANDING AT PETROL PUMP FUME FREE CHAMBER FOR WELDING SHOP B327 FALSE CEILING INSIDE OFFICE AND CUSTOMER SHED WITH HARDSTANDING AT ZAMORIN GAS AGENCY AND ADDITION ALTERATION TO SAILOR

Amount

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth; and not exceeding 10 sqm on plan for foundation, etc. and getting out in hard/dense soil complete, all as specified.

M&L for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete.

M&L for Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for rough finished surfaces of concrete complete as specified

M&L for Use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete complete as specified

M&L for Use and waste formwork to sides of beams for rough finished surfaces of concrete complete as specified.

M&L for Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete as specified

M&L for Reinforced cement concrete M30 (design mix) using graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete for column footing complete as specified and as directed. (Note: Reinforcement will be measured and paid separately)

M&L for Reinforced cement concrete M30 (design mix) using graded stone aggregate for column complete as specified and as directed. (Note: Reinforcement will be measured and paid separately)

M&L Reinforced cement concrete M30 (design mix) using graded stone aggregate for beam complete as specified and as directed.(Note: Reinforcement will be measured and paid separately)

M&L Reinforced cement concrete M30 (design mix) using graded stone aggregate for Slab complete as specified and as directed. (Note: Reinforcement will be measured and paid separately)

S&F Mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete as specified and as directed.

All as per item No.12 above but 5mm dia over up to and including 8mm dia complete as specified and as directed.

All as per item No.12 above 5mm dia over up to and including 10mm dia stirrups complete as specified and as directed.

M&L pre-cast cement concrete block in cement concrete masonry 1:3:6 type C-1 ( using 20 mm graded stone aggregate)with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 complete as specified and as directed.

M&L Providing precast cement concrete louvers and jallies, 25mm thick (measured solid), including all mouldings Type C0 1:3:6 using 12.5mm graded aggregate complete as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 surfaces finished even and smooth complete as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in ceilings using cement mortar 1:4 finished even and smooth without using extra cement complete as specified and as directed.

M&L for applying a coat of blown type bitumen grade 85/25 conforming to IS:702 heated to working temperature of 180ºC and applied @ 1.20 Kg per square metre of the surface area and provide a layer of 4mm thick APP modified torch applied water proofing membrane weighing not less than 4.00 Kg per square meter reinforced with nonwoven polyester matt, weighing not less than 160gm/sqm having softening point not less than 140oC, Longitudinal tensile strength not less than 650 N/5 CM, tear strength of 180N(Min), a static puncture resistance of 180, keeping a minimum of 10 cm over laps and 15cm end lap complete as specified and as directed.

M&L for two coat of oil emulsion distemper on walls including preparation of new plastered surfaces and priming Chalk whiting, on plastered surfaces, preparatory to distempering complete as specified and as directed.

M&L for preparing new plastered surface and applying two coats of antifungal paint Apex ultima or equivalent over a coat of primer on wall surfaces complete as specified and as directed.

M&L for two coat of oil emulsion distemper on celling including preparation of new plastered surfaces and priming Chalk whiting, on plastered surfaces preparatory to distempering complete as specified and as directed.

S&F Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide including preparation of new steel surfaces over 10 cm width or girth complete as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm complete as specified and as directed.

Spreading and levelling in layers n exc. 25 cm thick filling under floor including watering as required complete as specified and as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete as specified and as directed.

M&L for Hardcore with broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface with broken stones or boulders complete as specified and as directed.

M&L cement concrete 1:4:8 type D-2 100 mm thick, (using 40 mm graded stone aggregate) as in filling and mass concrete complete as specified and as directed.

M&L for PCC 1:2:4 type B1 ( using 20 mm graded aggregate) 40 mm thick as in flooring complete as specified and as directed..

S&F 38mm thick glass dividing strips, 3 mm thick, inserted in position, confirming to design complete as specified and as directed.

M&L for PCC 1:3:6 type C2 ( using 40 mm graded aggregate) 75 mm thick as in plinth protection/hard standing complete as specified and as directed.

S&F of machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 80mm thickness, M-35 Grade with grey cement and pigment complete as specified and as directed.

M&L for sand filling in, including spreading , levelling, watering and well ramming in layers not exc 25cm thick on ground complete as specified and as directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete as specified and as directed.

S&F steel work in tubular trusses including special shaped washers etc, complete using ERW or induction butt welded tubes conforming to IS 4923-1968 Grade ST-240 for square or rectangular tube complete as specified and as directed.

S&F Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe 410 -W (Gde-E-250) quality-A complete as specified and as directed.

S&F aluminium powder coated door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete as specified and as directed.

S&F Anodised powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete as specified and as directed.

S&F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete as specified and as directed(minimum thickness of powder coating 50 micron).

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete as specified and as directed.

M&L for 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium frame work complete as specified and as directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed to aluminium (extruded section) body complete as specified and as directed.

S&F 150 mm long Mild steel barrel tower bolts of extruded section complete as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor - Overall length of cover plate - 140mm complete as specified and as directed.

S&F Mortice lock, vertical type, size 100 mm - Mild steel - 4 Levers complete as specified and as directed.

S&F Anodised aluminium snap grid frame work for false ceiling of grid size 605mm x 605mm complete as specified and as directed.

S&F Hangers 6 mm dia. G.I. (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long size of grid 605mm x 605mm complete as specified and as directed.

M&L for Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws of 4mm thick complete as specified and as directed.

M&L for preparation of newly board ceiling and applying two coats of oil bound distemper emulsion over a coat of alkali resistant primer complete as specified and as directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in hard/ dense soil.

M&L for Cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete as specified and as directed.

S&F of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to all, fixed with self tapping screws complete as specified and as directed.

M&L for 100 mm thick cement concrete 1:2:4 type B-1, (using 20mm graded granite stone aggregate) as in hard standing complete as specified and as directed.

M&L chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed in neat cement slurry and pointed with mixture of grey and white cement to match the surfaces in floors over screed bed or bedding layer of cement mortar 1:6, 20mm thick complete as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete as specified and as directed.

Taking down cement plaster on bricks or stone walls including raking out joints hacking for key scrubbing down with water etc complete as specified and as directed.

Dismantling aluminium doors including glass pane/prelaminated particle board complete as specified and as directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire stapple.

S&F in repair Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire stapple.

M&L 4 mm thick Sheet glass ordinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane.

S & F 4 mm thick Sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane.

S&F Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixe with coach screw and washer in roof, wall etc.

S&F 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels and covered with decorative face veneer on both faces with lipping etc complete as specified and as directed.

S&F Curtain rails/Harrison rails, anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers and decorative Cap at ends etc complete as specified and as directed.

S&F 200 mm size aluminium anodised barrel tower bolt of extruded section complete as specified and as directed.

S&F 100mm Stainless steel butt hinges, cold rolled medium weight complete as specified and as directed.

S&F 150 mm size aluminium handles, cast type anodised complete as specified and as directed.

M&L for one coat of oil emulsion distemper on walls including preparation of old surfaces complete as specified and as directed.

M&L for preparation of old painted surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint on steel/iron surfaces complete as specified and as directed.

Demolition Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete as specified and as directed.

S&F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor (Work in foul condition and in shaft) complete as specified and directed.

S&F, PVC (SWR) reducer 110mm dia any radius complete as specified and directed.

S&F, PVC (SWR) bends 110mm dia any radius (Work in foul condition and in shaft) complete as specified and directed.

M&L for cutting into existing manholes for connecting new drains 150 mm dia, making good to pipe and rendering, cutting out existing benching for forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1,smooth finished, and reforming benching as required (Work in foul condition and in shaft) complete as specified and directed.

M&L for Point wiring complete as specified with 1100 volt grade confirming to IS 694, 1.5sq.mm (nominal area) single core PVC insulated unsheathed FRLS cable multi-stranded copper conductor drawn through and including in stove enamelled steel conduit of suitable size but not less than 20mm dia, with all fittings, fixed on wall/ceiling /floor including fixing of rotary switches and duly earthed with same cable as for point wiring above but green in colour as continuous earthing wire for one light/point controlled by one rotary switch complete as specified & directed by Engineer-in-Charge.

Material and labour for colour code point wiring FRLS PVC insulated and unsheathed cable with 1.5 Sqmm copper conductor single core multistrand 1100 Volt grade confirming to IS 694 drawn through PVC casing and capping of size 20/25mm, Junction boxes, suitable size gang box including 1.5 Sqmm earth wire copper insulated wire connected to common earth dolly complete as specified and as directed for One light point controlled by one modular switch.

Material and labour for colour code point wiring FRLS PVC insulated and unsheathed cable with 2.5 Sqmm copper conductor single core multistranded 1100 Volt grade confirming to IS 694 drawn through PVC casing and capping of size 20/25mm,Junction boxes, suitable size gang box with 3 pin socket outlet 6/16 A independent board including 2.5 Sqmm earth wire copper insulated wire connected to common earth dolly complete as specified and as directed. Note for item No. 77 to 79 :- (i) Necessary in stove enamelled steel conduit junction boxes for identifying junction as required on site/directed by Engr-in-charge for point wiring work with dummy plates shall deemed to be included in the quoted rate. (ii) Same size wire shall be used for phase, neutral & earth conductor (iii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads.

S&F modular switch one way 6A/16,1 module complete as specified and as directed.

S&F modular white cover plate with frame 3 module complete as specified and as directed.

S&F modular socket 6/16Amps 2/3 pin 2 module complete as specified and as directed.

S&F ceiling rose, three terminal, PVC/Polycarbonate, insulated body, ISI marked complete as specified and directed.

M&L sub main wiring using 2 runs of 4 sq mm FRLS PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC casing caping along with 1 run of 4 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly complete as specified and directed by Engr-in-charge. Note :- (i) One run of PVC casing and caping , 3 runs of 4 sqmm PVC insulated copper conductor cable will be measured as one unit. (ii)Strictly follow the proper colour code red/yellow/blue for phase , black for neutral and green for earth.

Supply and fix LED tube light luminaire 20W 4 feet output lumens greater than 100 lumen/watt, CRI = >60, CCT = > 4000, Internal surge protection up to 2KV, Power Factor >0.95 warm white with single piece integral with epoxy powder coated aluminium housing with die cast aluminium frame with housing complete as specified and directed by Engr-in-charge.

Supply and fix LED down lighter recess mounted with satin finish side rim 2x2, 33W(+/-2W) output greater than 125 lumens per watt,CRI-80,Internal surge protection up to 4 KV, Power factor greater than 0.95 ,THD=< 10% polystyrene diffuser for UGR less than 22,50000 burning hours as per L 70 and 4000K CCT, warm white complete as specified and directed by Engr-in-charge.

Supply and fix recess mounted LED down lighter warm white with die cast housing finished in white powder coating 15W complete as specified and directed by Engr-in-charge.

Supply and fix wall mounted fan with 450mm sweep, with inbuilt fan regulator, single phase 240 V,50Hz complete as specified and directed by Engr-in-charge.

Supply and fix switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete as specified and directed by Engineer-in-Charge.

Supply and Fix LED tube light fitting 2 x20W flameproof type FLP-WP made of aluminium alloy LM6, with electronic ballast, bipin holders, connector block, recommended for Gas / vapour group of IIA & IIB and zone 1&2 IP 65protected etc. complete with all accessories prewired and including connecting up with three core 1.5Sqmm FRLS copper conductor complete as specified and directed by Engineer-in-Charge.

Supply and fixing Sheet steel enclosure LM6 flame proof MCB DB SPN - 4 ways with 200 A rated bus bar & neutral link complete as specified and directed by Engineer-in-Charge.

Supply and fixing MCB single pole & neutral 240 volts, 6-32amps, 10KA , C-Curve complete as specified and directed by Engineer-in-Charge.

Supply and fixing MCB single pole 240 volts, 6-32 amps, 10KA, C-Curve complete as specified and directed by Engineer-in-Charge.

M/S V ASSOCIATES

Gates Infra Construction Co

KDR CONSTRUCTION

Palace constructions