Construction of Staff Quarters TypeII for Judicial Staff at Mohkampur Dehradun

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including

disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by

ramming and watering, lead up to 50 m and lift upto 1.5 m.

3 2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. Cum 40.50 2123.75 86,012.00

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of

rubbish up to a distance of 50 m outside the periphery of the area cleared.

5 2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% lit 328.82 234.75 77,190.00

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors

6 2.35.3.1 using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match Sqm 411.03 310.05 127,440.00

the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Total Earth work 642,243.00

Cement Concrete work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand

(zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses,

string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering Cum 13.84 9895.20 136,950.00

and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses,

string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering Cum 60.80 8519.20 517,967.00

and finishing: 1:5:10 (1 cement : 5 coarse sand (zone-lIll) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20

mm nominal size derived from natural sources).

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface

with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

12 4.14 Extra for concrete work in superstructure above floor V level for each four floors or part thereof by mechnical means. Cum 29.59 169.45 5,014.00

Total C. C. Work 1,465,223.00

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of

13 5.33 concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of

centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of

the specified mininum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

13.1 5.33.1.1 All works upto plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cum. Cum 369.15 9504.75 3,508,678.00

13.2 5.33.2.2 All works above plinth level upto floor V level, Concrete of M30 grade with minimum cement content of 350 kg /cum in columns, pillars piers etc. Cum 240.40 10011.35 2,406,681.00

13.3 5.33.2.1 All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cum in lintel beams and girders etc. Cum 793.40 9860.40 7,823,241.00

14 5.35 Add for using extra cement in the items of design mix over and above the specified cement content therein. qtl 467.58 733.50 342,969.00

15 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. Cum 364.05 355.65 129,474.00

5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

16 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 367.41 392.15 144,080.00

Contractor 2 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

17 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 2065.64 961.30 1,985,700.00

18 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 2098.16 736.40 1,545,085.00

19 5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 3828.29 927.25 3,549,782.00

20 5.9.7 Stairs, (excluding landings) except spiral-staircases Sqm 442.26 764.95 338,307.00

21 5.9.19 Weather shade, Chajjas, corbels etc., including edges Sqm 126.06 951.10 119,896.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Total RCC WORK 45,653,248.00

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement

mortar 1:6 (1 cement : 6 coarse sand)

25 6.5 Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. cum 207.49 169.45 35,160.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1

cement :4 coarse sand)

27 6.14 Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. sqm 810.33 15.00 12,155.00

28 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. Sqm 2019.02 104.80 211,593.00

TOTAL BRICK WORK 7,794,526.00

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and

29 9.21.1 well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt Sqm 507.55 2392.65 1,214,390.00

hinges with necessary screws

30 9.47 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia (heavy type) mtr 396.16 175.00 69,328.00

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

32 9.74.1 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm Nos 524.00 441.60 231,398.00

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with

necessary screws etc. complete. 150x10 mm.

34 9.81.1 Providing and fixing bright finished brass handles with screws etc. complete: 125 mm Nos 524.00 256.65 134,485.00

Providing and fixing aluminium handles, IS] marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with

necessary screws etc. complete : 100 mm.

36 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Nos 262.00 121.65 31,872.00

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto

37 9.84 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Nos 34.00 983.15 33,427.00

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade,

with necessary screws etc. complete..

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of

adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required)

extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour

and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash

adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware,

SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1

9.147.A to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically

jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc.

After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as

9.147.A per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design

approved by Engineer-in-Charge.

Contractor 3 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:

16231 shall be paid separately.

Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875

— Part 3 (ii) Sites with structure height more than 20m for all wind speeds

Three track three panels sliding door with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on two

panels along with multi-point locking system, adjustable nylon rollers with SS 304 body.

9.147.B3.1 Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (74 mm & above). (Height upto 2.5 metre). Sqm 259.60 10078.95 2,616,495.00

Total Wood Work 5,864,872.00

Sub Head VI STEEL WORK

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb,

bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,

including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-

treatment of the surface as directed by Engineerin-charge:

42.1 10.14.2.1 (A) "Profile C" Fixing with adjustable lugs with split end tail to each jamb (DR) R.M. 198.80 611.75 121,616.00

42.2 10.14.1.1 (B)"Profile B" Fixing with adjustable lugs with split end tail to each jamb (SR) R.M. 1053.92 583.30 614,752.00

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows

43 9.27.2.1.1 and clerestory windows with hinges and necessary screws. (30 mm thick shutters) with ISI marked M.S. pressed butt hinges bright finished of required size. Second class teak sqm 80.64 4326.80 348,913.00

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and

44 21.1 sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including

cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

(Glazing, paneling and dash fasteners to be paid for separately)

44.1 21.1.1.2 For fixed portition: Powder coated aluminium (minimum thickness of powder coating 50 micron) Kg 448.96 530.90 238,353.00

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM

44.2 21.1.2.2 rubber / neoprene gasket required (Fittings shall be paid for separately): Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 1767.76 634.45 1,121,555.00

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural

45 21.3.2 drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness (weight not less than Sqm 484.08 1505.25 728,661.00

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved

design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the Kg 1122.40 638.35 716,484.00

grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and

direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete: Stainless steel (grade 304) wire gauze of 0.5

mm dia wire and 1.4 mm aperture on both sides

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of

approved steel primer. M.S. tube

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural

drawings and direction of Engineer-in-charge complete.

49.1 21.8.1 Upto 5mm depth and 5 mm width Rm 1427.84 96.75 138,144.00

Total Steel Work 8,496,625.00

Providing and laying Vitrified tiles in floor in 600x600 mm size (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to 1S:15622,

of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm

50 11.41A.3.1 including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the Sqm 1346.00 1464.85 1,971,688.00

notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish.

Providing and laying Vitrified tiles in 600x600 mm size (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of

51 11.46.2 approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Sqm 204.48 1623.05 331,881.00

sqm including grouting the joint with white cement & matching pigments etc. complete.

Contractor 4 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in

52 11.38 all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 Sqm 243.20 1315.30 319,881.00

kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except

burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 Sqm 989.86 1267.95 1,255,088.00

coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with Sqm 97.44 3071.05 299,243.00

white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge.

Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator ,

vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel Cum 34.37 9823.80 337,618.00

shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and

polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement

slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Total flooring 7,047,252.00

Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre

painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm

58 12.54.2 made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at

1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction

perpendicular to it at 600 mm centers with help of suspension brackets.

Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing

with clip in tiles into spring ‘T’ with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet sqm 243.20 2354.65 572,651.00

having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holesand having NRC of 0.5, electro statically polyester powdercoated of

thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement

59 22.3 slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of

vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

22.3 (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). Sqm 392.56 769.60 302,114.00

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:

(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. -

(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. -

(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289

kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in -

parapet all around.

22.6 (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. Sqm 484.96 688.90 334,089.00

61 22.14.1 Grading roof for water proofing treatment Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) Cum 47.17 8042.30 379,355.00

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of

following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by

Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including

rounding of junctions of walls and slabs.

Contractor 5 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster

and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as

directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement :

3 fine sand) as per standard design : In 75x75 mm deep chase.

Total Roofing 2,412,382.00

64 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) Sqm 6519.27 333.35 2,173,198.00

65 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) Sqm 4888.31 383.00 1,872,223.00

66 13.16.1 6 mm cement plaster 1:3 (1 cement: 3 fine sand) Sqm 3143.12 300.45 944,350.00

67 13.50.2 Applying priming coat : With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood. Sqm 1218.10 74.65 90,931.00

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer

applied @ 0.90 kg/10 sqm).

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all

69 13.41.1 complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 Sqm 9536.36 185.65 1,770,425.00

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of

suitable shade with ordinary paint of approved brand and manufacture.

71 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. Sqm 9536.36 262.70 2,505,202.00

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even

and smooth complete.

Total Finishing 11,374,314.00 -

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick

ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1

cement : 4 fine sand).

Total Miscellaneous 70,842.00 -

Total Civil Work 90,821,527.00 -

Plumbing Details (Internal)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and

making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with

fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including Nos 64.00 8006.60 512,422.00

painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard

board backing : Oval shape 450x350 mm (outer dimensions)

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40

mm long screws, rawl plugs etc., complete

79 17.34.1 Providing and fixing CP Brass toilet paper holder. Nos 64.00 803.70 51,437.00

Providing and fixing unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, Single socketed pipes. Upvc pipe 110 mm diameter

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450

mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion : Upvc nahani trap 110x110mm dia.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Contractor 6 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S.

84 12.43.2 screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. Nos 846.00 371.30 314,120.00

Providing and fixing unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion : Upvc terminal guard 110 mm dia.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion : Upvc plain bend 110 mm dia.

Providing and fixing unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion : Upvc door bend 110 mm dia.

89 17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia Nos 128.00 119.55 15,302.00

Providing and fixing unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion : Upvc tee 110 mm

91 17.8 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. Nos 96.00 1683.35 161,602.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting

and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 225 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm

gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110x110x110 mm tee

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm Shoe

97 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4). Nos 17.00 298.25 5,070.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

98.1 18.8.1 15 mm nominal outer dia Pipes R.M 956.80 497.80 476,295.00

98.2 18.8.2 20 mm nominal outer dia Pipes R.M 1669.80 537.60 897,684.00

98.3 18.8.3 25 mm nominal outer dia Pipes R.M 99.40 627.25 62,349.00

99 18.12.4 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore R.M 75.00 540.30 40,523.00

100 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore Nos 64.00 506.80 32,435.00

101 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore Nos 64.00 670.45 42,909.00

102 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

103 18.58.1.1 Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia Nos 192.00 37.60 7,219.00

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes

for inlet, outlet and overflow pipes but without fittings and the base support for tank.

105 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore Nos 32.00 462.50 14,800.00

106 18.20.3 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore Set 32.00 486.80 15,578.00

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

109 18.53A Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. Nos 32.00 74.80 2,394.00

110 18.22.2 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter Nos 64.00 222.35 14,230.00

Contractor 7 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Total Plumbing (Internal) 4,336,485.00 1,108,242.00

Building Façade & Modular Kitchen work

Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1800mm length (minimum) and 130 mm wide (minimum),

in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary

profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work

111 26.3 height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first Sqm 693.00 6283.85 4,354,708.00

layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum

Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400 mm and length of 595 mm of approved

texture,design and pattern having Flexural Strength/ Modulus of Rupture of ≥ 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-

3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical ‘T’ (for intermediates)/ ‘L’(for ends/ termination)/ Tubular

sections (at corners)of size 80x60x2 mm/ 40x60x2 mm / 40x40x2 mm respectively,

spaced at maximum spacing of 600 mm c/c matching to the tile vertical grid, and horizontal aluminium ‘C’-clamps of size 56x25x2 mm thickness of length 150 mm at junction of

tiles and of length 75 mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400 mm c/c matching to the tile horizontal grid with two numbers of

26.92 self-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers. The vertical ‘T’/’L/ Tubular’ sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-

brackets (galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and

stainless steel grade 304,M10 full threaded anchor fasteners with nylon sleeve 100 mm long (for brick work) and M8 expansion anchor fasteners 75 mm long for concrete surface,

spacing of brackets to be based on a structural/ static calculation. The brackets shall be of length 175 mm at junction of two vertical aluminium profiles and of length 100 mm at

26.92 intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25 mm

with EPDM washers.

EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends.

The tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size which shall be inserted and pressed into position on the ‘C’ clamps holding

the tiles and the cut-tiles shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. The vertical joint open groove between two adjacent tiles

26.92 shall be 5 mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rain

screen principle with provision for natural ventilation of the space between the façade tiles and the structural wall. The work shall be carried out as per specification, drawing and

as per direction of the Engineer-in-Charge.

Note : Scaffolding wherever required to be paid separately

112.1 26.92.2 With 16 mm thickness (+/- 10%) terracotta tiles of other than grey colors Sqm 441.66 5991.40 2,646,162.00

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions

of the building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight

including checking of all the structural and functional design.

(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick

aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite

panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer

(Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316

Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item

includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests

on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the

handing over of the building for occupation.

The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as

per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on Sqm 592.84 5015.05 2,973,122.00

the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per

grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer- kg 5276.28 414.30 2,185,963.00

in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this

account). The weight of aluminium extruded section shall be taken for purpose of payment.

Finishing walls with textured exterior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied

@ 2.20kg/10 sqm

Contractor 8 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of

scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock

system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution

of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter.

The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with

essential safety features for the workmen etc., complete as per directions and approval of Engineer in charge. Sqm 3962.74 338.25 1,340,397.00

Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand

and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry Sqm 1134.66 109.90 124,699.00

surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-Incharge (The rate is inclusive of all materials &

labours involved except scaffolding).

Cleaning of exposed concrete, Brick, Stone surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning

with oil free air blast as per direction of Engineer in charge.

120 AR-1 Supply & installation of 28 mm WPC Jali of size 7'x3' or as per requirment, Complete with Scafolding & Fixing as per approved Design. Sqm 135.95 5881.00 799,522.00

Providing and fixing 18 mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded

121 9.166.1 steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to Sqm 1021.44 1362.30 1,391,508.00

be paid separately).

Providing and fixing 6 mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded

122 9.167 steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge. Sqm 355.20 1010.60 358,965.00

Providing and fixing cupboard shutter with 19 mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved

123 9.168 brand including 2 mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per Sqm 329.28 2829.25 931,615.00

direction of Engineer-in-charge. (Payment of providing and fixing auto closing hinges shall be paid separately)

124 9.170 Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. 200 mm Nos. 128.00 186.65 23,891.00

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws

including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack,

Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The

127 9.173 same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in-charge. (For payment purpose only kg 1728.00 533.25 921,456.00

weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing

and fixing telescopic channel shall be paid separately)

Providing and fixing 2 mm thick 16 to 19 mm wide PVC edge binding tape of approved quality for cupboard/ wardrobe shutters including necessary synthetic resin hot pressed to

edges on binding machine etc. complete as per direction of Engineer- in-charge.

129 9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete. Nos. 640.00 52.50 33,600.00

130 9.81.1 Providing and fixing bright finished brass handles with screws etc. complete: 125 mm Nos. 384.00 256.65 98,554.00

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same

etc. complete as per direction of Engineer-incharge.

132 AR-2 Supply & installation of Stainless Steel Door Viewer (Magic eye) of approved quality and make including necessary screws etc. complete. Nos. 32.00 540.00 17,280.00

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 75 mm

Total Building Facade & Modular Kitchen work 18,987,107.00 816,802.00

Electrical Work (Internal)

Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with

134 1.10 modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed mediumclass PVC conduit alongwith 1 No. 4 sq. mm FRLS

PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm

FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Contractor 9 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC

conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit

as required. 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the

existing surface/ recessed steel/ PVC conduit as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch,

140 1.11 modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Nos 76.00 1562.00 118,712.00

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of

recessed conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet

and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet

and 15/16 A modular switch, connections etc. as required.

144 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. Nos 32.00 99.00 3,168.00

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar,

145 2.4.2 neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6way 4+18 Double Door Nos 2.00 4974.00 9,948.00

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with

146 2.10. connections, testing and commissioning etc. as required.

Single pole and neutral

146.2 2.10.2 Single pole and neutral No 41.00 599.00 24,559.00

147 2.13 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering

pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as

10.18 DSR Providing and fixing Hexagonal MS sheet fan box for ceiling fan clamp od internall dia 140mm, 73mm height top lid of 1.5mm thick MS sheet with its top surface hacked, MS

clamp shall be made of 12mm dia MS bar bent to shape as per standard design.

152 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. No. 128.00 87.00 11,136.00

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

153.3 1.24.6 Telephone socket outlet No. 96.00 148.00 14,208.00

153.4 1.24.7 TV antenna socket outlet No. 96.00 148.00 14,208.00

154 1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 module No. 192.00 327.00 62,784.00

Providing and fixing plain 16/0.20mm (0.50sqmm) twin circular flexible FRLS PVC insulated, PVC sheathed copper conductor cable direct on the wall with PVC clips etc. as

Contractor 10 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Supply, Installation, Testing and commissioning of of Surface mounted type 36 watt LED Batten 6500K cool white SMD LED light source,1150mm ,140-270V, 50 Hz, pf >=0.9,

Aluminium Housing, Minimumm lamp Effeciency 100lm/W,Chip Efficency 130lm/W, polycarbonate diffuser,in built control gear having driver efficiency more than85%, minimum

156 NSI-1 CRI-80, Ingress Protection IP20, Total Harmonics less than 20%,Beam Angle >=120,Lumen Maintenance >=80% after 6000 burning Hours, capable to with stand 2.5 Kv Surge No. 292.00 1709.00 499,028.00

voltage,minimum 50000hours LED Life,as per IS 103229Part.V sec.1, 2012 along with Photobioloical safety LED as per IS:16108/2012 /IEC:62471;2006. completewith all accesories

including connections etc as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades,

30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.0, Air delivery minimum 210

157 19.1 CMM, 350 RPM (tolerance as per IS : 374 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut Nos 96.00 2730.00 262,080.00

bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as

Supply, Installation, Testing and commissioning of of Ceiling mounted type 100 watt High Bay suspension Type Luminary with matallic adjutable Bracket with Eye Bolt 3500K

,140-300V, 50 Hz, pf >=0.95, Pressure Die Cast Aluminium Alloy Housing, Minimumm lamp Effeciency 120 lm/W, polycarbonate UV Stablised Optical Type diffuser,in built control

158 NSI-2 gear having driver efficiency more than equal to 85%, minimum CRI-70, Ingress Protection IP67, Total Harmonics less than 10%,Beam Angle >=120,Lumen Maintenance >=80% Nos 2.00 7200.00 14,400.00

after 6000 burning Hours, capable to with stand 1.5 Kv Surge voltage for one minite ,5 KV Transient Surge,,minimum 50000hours LED Life,as per IS 15802Part.XV Section-2 &

16105 Part-2 sec.1, 2012 latest along with Photobioloical safety LED as per IS:16108/2012 /IEC:62471;2006. completewith all accesories including Installation at hight upto 10

meters connections, Testing etc as required.

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Distribution Bus Box fabricated out of 14 guage CRCA sheet steel in cubical,

compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland

159 NSI-3 plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. bus box shall be suitable Job 17.00 86269.00 1,466,573.00

for accomodating Energy Meters as per UPCL Norms with a loose wire box and sealable bus bar Chamber. (All hardwares like nuts and bolts used shall be Galvanized and Zinc

Building Meter Bus Box as per UPCL specification mentioned below

BUS BAR 100 amps TP&N

2 nos 60 amps Single phase energy meters

Outgoing - 2 nos 40 ampsDP MCB.

Supply Installation testing & commissioning oof 18W Inverter LED batten with backup 4 hrs , Charging Time 8 hours, 6300K,85% Driver Efficeincy,,system Efficiency

100lm/W,system current less than 106mA,builtin Electronic Control Gear ino. Li-Ion Batteru having Backup of 6 hours,with Extruded Aluminium Housing, Polycarbonate Diffuser,

160 NSI-4 minimum CRI-80, Ingress Protection IP20, Total Harmonics less than 20%,Beam Angle >=120,Lumen Maintenance >=80% after 6000 burning Hours, capable to with stand 1.5 Kv Nos. 76.00 1250.00 95,000.00

Surge voltage for one minite 2.5 KV Transient Surge,,minimum 50000hours LED Life,as per IS 10322Part.V & 10107 Part-2 sec.1, 2012 along with Photobioloical safety LED as per

IS:16108/2012 /IEC:62471;2006. completewith all accesories including connections etc as required

Supply, Installation, Testing and commissioning of of surface Mounted 9 watt LED bulk Head Plastic Luminary 6500K cool white ,240 v, 50 Hz, pf >=0.95, Die Cast Aluminium

Housing, Minimumm lamp Effeciency 100 lm/W,Chip Efficency 130lm/W, polycarbonate diffuser,in built control gear having driver efficiency more than equal to 85%, minimum

161 NSI-5 CRI-80, Ingress Protection IP55, Total Harmonics less than 20%,Beam Angle >=120,Lumen Maintenance >=80% after 5000 burning Hours, capable to with stand 2.5 KV Transient Nos. 4.00 1928.00 7,712.00

Surge,,minimum 50000hours LED Life,as per IEC safety Class (1)i completewith all accesories including connections etc as required.

162 NSI-6 Supplying and fixing of wall bracket polycarbonate powder coated upside down side glass shade, connections Testing etc. as Required. No. 128.00 579.00 74,112.00

S I T C of 300 swwep ISI Marked 4 pole ,3 blades,capacitor Type E Class Insulation , Propeller Type totally enclosed Motor Exhaust fan as per IS 2312/1967 Latest compleate with

all accessories with Bird Screen suitable to operate on 240V single phase 50 Hz AC supply with o.0 9Pf and minimum Air Delevary as per table-2 of IS2312 :1967 and maximum

Wattage Input as per table 2 of IS 2312:1968 including Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning

etc. as required. as reqd.

Providing & Fixing of vartical ISI Marked ABS Engineering Plastic Gyser (water Heater) 25 Liter Capacity. BEE 5 Star Rating with Vitrious Enamel vented type inner Container as

164 NSI-9 per ISIS 2082:2018 latest 60N/Sq.cms. Pressure Rating with pressure safety Release and 2 meters Extension Chord and all standatd mountings and accessories , making water Nos 32.00 15230.00 487,360.00

connection etc as reqd.

165 2.11 S/F single pole blanking plate in the existing MCB DB complete etc. as required. (4 no. /MCBDB) Nos 165.00 13.00 2,145.00

Supplying and fixing following rating, Double pole, (Single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB

167 2.15 DB complete with connections, testing and commissioning etc. as

Contractor 11 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP

MCB, "C" curve including connections, painting etc. as required. For AC

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate One Module for modular switches in recessincluding supplying and fixing Anchor Cat-6

Data Information Outlet, crimpling, connection, testing etc. as required.

170 1.53.2 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run mtrs 1600.00 96.00 153,600.00

Supplying installation testing commissioning of 24 Port, 2 layer,Web Managed, 4 SFP Port, 56 Gbps switching capacity,41.7MPPS Thoughtput,Data switch Dlink with 2 U rack ,

cable maneger etc as reqd.

Supplying and fixing 8 way, Double Door single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes

etc. complete as required.

174 6.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) Mtr. 200.00 126.00 25,200.00

175 6.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run Mtr. 60.00 197.00 11,820.00

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I.bolts, nuts, chuck nuts and spring washers etc. complete as required.

177 6.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. Mtr. 50.00 195.00 9,750.00

Total Electrical Work(Internal) 17,921,470.00 2,964,309.00

Electrical (External)

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering

pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as

Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays with perforation not morethan 17.5%, in convenient sections, joined with

connectors,suspended from the ceiling with M.S. suspenders including bolts& nuts, painting suspenders etc as required.

180.1 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Mtrs 50.00 777.00 38,850.00

Total Electrical (External) 324,546.00 -

Supply ,installation testing and commissioning of 13 Pessenger (844Kg.)Machine Room less lift having contract speed of 1.5 meter per second serving four different floors (S+8+T)

10 floors , Type(MRL) Machine room less with gearless traction having + /- 5% landing accuracy,,speed 1.5 mps,10 levels with a total travell of 34 mtrs,(approx.) with 10 stops

181 MR and doors opening all on one side,with VAVF cotroller,having ARD with Dry MF batterirs, Microprocessor based simples slective collective with attendent operations,415 V 50 Hz 3 Each 2.00 2521150.00 5,042,300.00

phase 4 wire power,with power operated centre opening horizontal sliding stainless steel scrach free car and landing doors, Car size and dimenssions suitable for hospital

strchers,, infra red curtain and one hour fire rating,,with overload waring indiactor,, concealed luminary with LED light, axial pressure ceiling fan, with voice annoucement system.

etc as required.

Total Lift Work - 5,042,300.00

Solar Power & Fire Fighting

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline

182 silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as

a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic

Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should

not be less than 90% at the end of 10 years and 80% at the end of 25 years.

b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with

efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency

level to suit the Grid Voltage Frequency.

c) Data Monitoring System complete with accessories.

d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other

accessories etc. as required.

e) Lightning and surge voltage protection.

f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules,

main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

Contractor 12 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Remark Solar inverter has 6 yr warranty, Solar panel have 10 yr warranty, AMC is required after 6 yr, 1 Array will have 10 panel connected in series, Connection 1 array have 10

panels in series 240 volts DC, 10 amp, Connection 10 array output in parallel 240 volts 100 amp DC, Connection output 2 parallel array in series 480 volts 100 amp. KWp 25.00 61060.00 1,526,500.00

Supplying, installation, testing and commissioning of solar water heating system with heat exchanger type including , make up water tank and piping etc, 200 liters Havells.

184 NSI-S-2 Supplying, installation, testing and commissioning of Solar Pathway light with panel , Battry and 20 w LED light. Nos 2.00 31361.00 62,722.00

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including,Welding, fittings like elbows, tees, flanges, tapers, nuts bolts,

185 18.7 gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthatic enamel paint of required shade complete

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS

5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

186.1 18.9.2 Single headed Stainless steel Nos. 10.00 6139.00 61,390.00

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked,

conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

187.1 18.10.2 Single headed Stainless steel Nos. 4.00 6139.00 24,556.00

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming

to IS 13095 of following sizes as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts,

washers, gaskets and conforming to IS 780 of following sizes as required

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and

internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal

193 18.17 internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the

equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to

interconnect hose pipe coupling as required

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe

connection conforming to IS 904 as required

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement

196 18.20 with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. set 1.00 18244.00 18,244.00

197 18.22 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. Nos. 1.00 1546.00 1,546.00

198 18.23 Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

DSR Civil Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes

for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Contractor 13 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Providing and fixing carbon-di-oxide fire extinguishers trolley mounted with all accessories internal discharge tube,high pressure discharge hose, discharge nozzle, suspension

bracket, ISI marked as per IS:2878 Finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.

Providing and fixing Carbon-di-oxide Fire Extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube. 30cms long

201 NSI-F-2 high pressure discharge hose. Discharge nozzle,suspension bracket, confirming to IS:934 finished externally with red enamel paint and fixed to wall with brackets with rawl

plug/dash fasteners complete with internal charge. (CCOE Nagpur Approved clynders)

202 NSI-F-3 Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.

203 NSI-F-4 Providing & fixing carbon steel Fire man axe with rubber insulated handle tested to 20000 volts. Nos. 1.00 626.00 626.00

204 NSI-F-5 Providing and fixing Mechanical foam ( AFFF) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.

Providing and Fixing of self illuminated /auto glow Exit signs printed on photoluminescent sheet containing self illuminated base chemical,of appropriate size not less than

400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site.

Supplying, installation, testing & commissioning of manual call box of MS construction in surface/in recess with stainless steel chain and hammar complete with glass & push

button etc. as required.

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metalliccover complete with all connections etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for

operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone

enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition

210 17.1.9.1 and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required 4 zone Each 8.00 8866.00 70,928.00

Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in

approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections,

211 17.1.10 interconnections etc complete as required. 10 Zone panel for fire alarm system 250 Watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-

3 complete with all accessories as required - 2 Nos.(one to act as standby) Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24 V DC

supply conforming to IEC-268 for simplex mode of operation/communication

suitable for 20 Nos.talk back unit -1 set.

Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24 V DC supply conforming to IEC-268 for simplex mode of operation/communication

suitable for 20 Nos.talk back unit -1 set. Annoucement control desk suitable for selection of different zones selectively and ON ALL CALL switch with visual indication etc.,

complete as required- 1 set. Amplifier change over switch for inter changing amplifier- 1 No. Monitor panel for loudspeaker complete output selector ON/OFF switch, fuse visual

17.1.10 indications etc. complete as required- 1 No. Gooseneck microphone with stand and ON/OFF switch -1 No. Mains ON/OFF switch, fuse indication lamps, DC and AC voltmeters & Each 1.00 70389.00 70,389.00

ammeters terminal blocks etc. complete as required -1 set. Battery charger trickle cum boost to take complete load of fire alarm & PA system complete with all accessories

including providing & fixing of 2 nos. 12 volt,30 AH each sealed maintenance free batteries -1 set.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zonebutton paging station) with seamless integration facility

withmain fire alarm panel for voice evacuation complete as required.

213 17.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required. Each 10.00 965.00 9,650.00

214 17.3.3 Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required Each 10.00 1793.00 17,930.00

215 17.3.4 Supplying, installation, testing & commissioning ofceiling/wall mounted loud speaker, 3/1.5 Watt in ABSenclosure complete as required Each 1.00 2428.00 2,428.00

216 17.3.7 Supplying, installation, testing & commissioning of digitalaudio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required. Each 1.00 145793.00 145,793.00

217 17.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required Each 1.00 81756.00 81,756.00

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer

218 17.5.1 of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. mtr 350.00 359.00 125,650.00

Supplying and drawing of cable Fire Retardant PVC insulatedcopper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required

219.1 17.5.3.2 speaker cable Two pair, 2-core, 1.5 sqmm mtr 200.00 89.00 17,800.00

219.2 17.5.3.4 speaker cable Four pair, 2-core, 1.5 sqmm mtr 100.00 158.00 15,800.00

Total Solar Power & Fire Fighting 3,985,415.00 1,258,332.00

Contractor 14 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

Supply, installation, testing and commissioning of 4 MP COMS 0.37 inch Sensor,4MP(2560×1440) ,,1080P ( 1920 x 1080 ) ,720 P resolution, 30 mtrs Ir, day night capable, Focal

220 NSI-C-1 Length(mm)3.6, Frame Rate (fps)30, Video Streaming Triple compressed stream,Minimum Illumination for Capturing Color Image0.03 lux WDR (Wide Dynamic Range) DWDR SNR No. 16.00 6837.00 109,392.00

(Signal to Noise Ratio) ≥52 Db Installation Type Outdoor with aluminium Housing, IP Bullet camera connections ,testing etc. as reqd,.

Supply, installation, testing and commissioning of 4 MP COMS 0.37 inch Sensor,4MP(2560×1440) ,3MP(2304×1296) ,1080P ( 1920 x 1080 ) ,720P ( 1280 x 720 ) ,D1 ,CIF ,480 x 240

resolution, 30 mtrs Ir, day night capable, Focal Length(mm)2.8, Frame Rate (fps)30, Video Streaming Dual compressed stream,Minimum Illumination for Capturing Color

Image0.002 lux WDR (Wide Dynamic Range) DWDR,SNR (Signal to Noise Ratio) 50-60 Db Installation Type Outdoor with aluminium Housing, IP Dome camera connections ,testing

Supply, installation, testing and commissioning of POE Layer 3 - access switch 24 ports, with, Management Port (RJ 45/RS 232/USB), Switching Capacity / Forwarding Bandwidth

(Non Blocking / Line Rate /Wired Speed) 2x (Numbers of access ports + Number of Uplink Ports) (Gbps) 128, RAM (MB) 256, Flash Memory (MB) 128, Throughtput / Forwarding

222 NSI-C-3 Performance (MPPS) 96, Number of VLAN Supported 4000, Number of VLAN IDs Supported 4000, Number of IPV4 Routes 500,Number of IPV6 Routes 500,Number of Mac Nos. 1.00 80593.00 80,593.00

Address Supported (k) 32, Basic Layer-3 Protocol from day 1 Static Routing,RIPv1,OSPFv2, Premium Layer-3 Protocol from day 1 802.1Qbb,802.1Qaz, DHCP

Snooping,ACL,802.1x,RADIUS/ TACACS,Port Security etc. as reqd,.

D-Link 6U Rack Enclosures Networking/Server Rack with cable management and Connectors etc. as reqd. D-LinkR

(NWR-6U-5045-GR)

Contractor 15 Digitally signed by RAHUL

Bill of Quantities

S.NO DSR NO. DESCRIPTION OF ITEM Unit Qty. Rate

64 Channels NVR with 4K (3840 × 2160), Recording Speed for all channels (fps)

Upto 60, Total Storage Capacity of the hard disk provided

40TB, SATA III Internal Hard Drive Interface,Internal Storage Expandable upto 16TB, Number of Hard Disks supported 8, Redundancy Option RAID 0,RAID 1,RAID 5,RAID 6,RAID

10,Conformity to Dry Heat test at Specified Maximum Operating Temperature for 16 hours as per IS :9000 latest, Conformity to Damp heat at 40 degree C - 95% RH (cyclic test):

two cycles of 16+8 hours as per IS: 9000 latest, Conformity to Cold test at Specified Minimum Operating Temperature for 4 hours as per IS: 9000 latest,valid BIS certificate as per

IS 13252 etc. as required.

81-82 CM LCD Monitor, 1920 x 1080 (Full HD) resolution, Aspect Ratio 16:9, 250 nits brightness, Response Time (millisecond) 5 millisecond, VGA Port, HDMI Port,Display Port,

Power Consumption in Operating Mode (Maximum) 36Watt, Power Consumption in Sleep Mode (Maximum 0.5Watt,Technology LED Backlit etc. as required.

226 NSI-C-7 FES 8 Ports Managed PoE+ Layer 2 Access Switch FESR (FES-GS-1010P) Nos. 1.00 33580.00 33,580.00

HDMI1.4 Cat.6 10.2 Hdmi Extender, HDMI resolution 1080p @ 50 / 60Hz, Supported audio formats Dolby, Storage Humidity (no condensation) 5% - 95 % RH, Data transfer rate

10.2 Gbps, ISO9001 Compliance etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of

recessed conduit as required.

229 1.53.2 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run Mtrs 550.00 96.00 52,800.00

Supplyin & Installation of FES 8 Ports Managed Non POE Layer 2 Access Switch (DGS-1210-10/ME) with SFP++, along with6 port Patch Panel LIU fully loaded including Patch chord,

Connectors etc. etc. as reqd.

231 NSI-C-10 Suppling Laying and fixing of 6 core OFC Cable as reqd. Mtrs 350.00 71.00 24,850.00

Total CCTV WORK 156,450.00 574,015.00

Contractor 16 Digitally signed by RAHUL