Building Works

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[1] Dismentling doors, windows, ventilators etc. (wood or 26.00 Each 244.98

steel) shutters including chowkhats architraves,

holdfasts and other attachment etc. complete and

stacking them within all lead and lift. (ii) Exceeding

Sq.M. in area.

[2] Removing and scraping of old deteriorated plaster of any 41.48 Sqm 18.94

thickness fromm wall / R.C.C member including stacking

of serviceable material and disposal of unserviceable

from site of work with all lead and lift

[3] Providing 15mm thick cement plaster in single coat on 63.00 Sqm 194.07

Rough (Similar) side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (ii) Cement mortar 1:4 (1-cement :4-

[4] Providing and laying Mirror polished Machine polished 53.00 Sqm 2629.03

Green Marble stone slab 18mm (Average) thick for doors

& windows sill & Jams clading as per design including

full moulded round front steps & 1cm nosing &

necessary groove on trads of steps ;laid on 20mm thick

cement mortar 1:6 (1 cement : 6 coarse sand) jointed

with gray cement sluury including rubbing and polsihing

etc. complete.for Doors / windows sill & jams clading.

[5] Providing and laying Vitrified tiles 8 to 10 mm thick, 24'' 230.00 Sqm 1073.13

x 24'' in flooring treads of steps and landing laid on a bed

of 12mm thick cement mortar 1:3 (1-cement : 3-coarse

sand) finishing with flush pointing in white cement.

[6] Providing and laying Vitrified tiles 8 to 10 mm thick, in 11.00 Sqm 1538.85

skrting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with

white cement slurry

[7] Providing and laying Vitrified tiles 8 to 10 mm thick, 36'' 68.00 Sqm 1484.61

x 36'' in flooring treads of steps and landing laid on a bed

of 12mm thick cement mortar 1:3 (1-cement : 3-coarse

sand) finishing with flush pointing in white cement.

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[8] Providing & Fixing of Armstrong Mineral Fibre 233.00 Sqm 1111.00

Acoustical Suspended Ceiling System with Dune

(Bevelled Tegular) Edge Tiles With Armstrong 15mm

Exposed GRID The tiles should have Humidity

Resistance (RH) of 99%, NRC 0.5, Light Reflectance

>85%, Thermal Conductivity k = 0.052 -0.057 w/m K,

Colour White, Fire Performance UK Class O / Class 1 (BS

476 pt -6 &7) in module size of 600 x 600 x 16mm,

suitable for Green Building application, with Recycled

content of 32% be laid on Armstrong Superfine 38 with

15 mm wide T -section flanges colour white having

rotary stitching on all T sections i.e. the Main Runner,

1200 mm & 600 mm Cross Tees with a web height of

38mm and a load carrying capacity of 14 Kgs/M2 &

minimum pull out strength of 100 Kgs .. The T Sections

have a Galvanizing of 90 grams per M2 and need to be

installed with Suspension system of Armstrong make.

[9] Providing and fixing Anodized Alluminum Section Jindal 51.00 Sqm 2809.82

Deluxe Sliding Window System 27mm series THREE

track window as shown in elevation, shutter with 5mm

thick transparent plain float glass, with transparent

silicon sealant with allu. anosized coated fittings and

fixture etc complete.

[10] Removing dry or oil bound distemper by a washing and 472.00 Sqm 10.99

scraping and sand papering the wall surface smooth

including necessary repairs to scratches complete.

[11] Wall painting with Applying two coats of putty & two 472.00 Sqm 160.01

coats of primer of approved brand & Three coats of

plastic emulsion paint of approved brand and

manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from

mortar droppings and other foreign matter and sand

papered smooth.

[12] Providing and fixing door Double shutter having factory 18.00 Sqmt 5968.09

fabricated std. Extruded aluminium colour anodized

hollow section {Section 63.50 x 38 mm x 2.50 mm thick }

for door frame, hollow portion of door frame shall be

filled with wood to be insert for durable grip of door

hinges, with factory made 38 mm.thick flush door both

side pre laminated with 6 Lever Mortice lock, SS Aldrop

30cm long, SS Handle size 15 Cm Long, Tower Bolt size

20 cm etc. as per detail colour & pattern approved by

this office including necessary anodized alluminum

fixtures and fastenings.

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[13] WALL PANELLING WITH TEXTURED VINEER AND 14.00 Sqmt 11009.00

FABRIC PANEL SHEET

Providing and fixing wall panelling made with50mm x

25mm thick Aluminium pipe with 12mm thick Red and

white grade plywood with 4mm thick premium quality

texture sheet with matt finish PU polish, Panelling with

8mm thick minereal fiber board panel which is covered

with 25mm thick 40 density cushion covered with

premium grade fabric, Panelling with 05mm thick

premiu grade texture phase vineer sheet with given

appropriate groove and finish with PU matt finish

malamine polish, Cushion panels are install with

premium grade glue with required necessery hardware

complete as per given details by architect and engineer

in charge.

[14] Providing and Arranging Cushioned Seat & back, PP 6.00 No 8743.31

outer back cover, PP arms, Single back lock, Push back

mechanism, gas lift for seat height adjustment, five prong

Nylon base with twin wheel nylon castor.Including all

materials and labour etc.Complete as per drawing and

instruction of engineer-in charge.Size : Max.Hight

1020mm Min.Height 930 mm, Seat : 500mm x 460mm,

Back: 500mm x 440 mm Low Back Chair :Priviya-7003

[15] Providing and Arranging PREMIUM EXECUTIVE 1.00 No 42745.06

REVOLVING CHAIR (Meduim Back) Sigma chrome Base

with Knee Tilt Synchro Mechanism with Any Position

back Lock, Seat & Back - Made from High Density U -

FOAM, Armrest in two pieces 12mm outer boire cut

veneer polyurathine High gloass & 6mm hot pressed

plywood upholstered pad which fix with seat .Including

all materials and labour etc.Complete as per drawing and

instruction of engineer-in charge.Size : max.Height :

1105 mm to Min. 1015mm, Seat : 660mm x 660mm, back

510 mm x 600 mm Molto 562 Meduim Back Chairs

[16] Providind and Arranging Medium Back Chair - Seat & 8.00 No 15219.83

back cushioned on ply, aluminum die casted arms with

cushioned pad, Synchro mechanism with single back

lock, gas lift, chrome base.Including all materials and

labour etc.complete as per detail drawing and

instruction of engineer-in charge.Size : max.Height

1070mm, Min.970mm, Seat: 490mm x 510 mm, Back :

640 mm x 510 mm MARCO 1002 Meduim back Chairs

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[17] Providing And Arranging table for chamber having 1.00 No 49568.38

overall thickness of Top 40 mm (18+18+4mm) 18 mm

thick MR Grade plywood and 4.00 mm thick veneer at

top with melamine polish finish including 8mm thick

back painted glass. Top to be made from 75mm x 50 mm

Indian teak wood with half round moulded on long side

with melamine polish. Leg 50 mm x 50 mm x 1.6 mm

thick CRCA Square pipe and supporting pipe 50 mm x

25mm x 1.8 mm finishing with epoxy powder coated

micron with leveller. Appron having 18 mm thick MR

Grade plywood with 4.00 mm thick veneer having

melamine polish finish. Drawer Unit-450 x 550 x

mm having all Structure 18 mm thick MR grade plywood

with veneer and teakwood border of specified size with

melamine polish finish. Drawers (3 Nos) slides on Ebco

make telescopic channel with Godrej make lock with two

keys and necessary fixtures and fastening as approved

with balancing laminate inside 0.8 mm thick of approved

shade including all materials and labour etc. Complete as

per drawing and instruction of engineer-in charge. Side

Unit to be provided saparetly. Executive Table with MDU

veneer Size :- 1800mm x 900mm x 750mm

[18] Providing and Arranging side unit with top 40mm 4.00 No 26166.13

overall thickness made from 18 mm thick MR grade

plywood with 4.00 mm thick veneer on top with

melamine finished polish. Side and drawer made of

18mm thick MR grade plywood with 4.00 mm thick

veneer with melamine finished polish and inside 0.8mm

thick balancing laminate of approved shade. Teakwood

border with melamine finished polish of specified size to

be provided all around the borders of plywood. Drawer

run on Ebco make telescopic channel with Godrej make

lock with Two keys and shutter fixed with auto hinges

incld. all necessary fixtures and fastening as approved

and back of the unit with 6mm thick MR grade playwood

with 0.8 mm thick laminate of approved shade with

nylon bullet including all materials and labour etc.

Complete as per drawing and instruction of Engineer-in

charge. Side Table veneer Size 1200 mm x 450mm x

[19] Providing And Arranging table top 37 mm thick made 5.00 No 19431.65

from 18 mm thick MR grade plywood with 1.00 mm

thick laminate finish.Leg & frame to made from 50 x

mm x 1.6mm & 50mm x 25mm x 1.8mm size CRC pipe

powder coated 50 micron finish with levlar Appron

mm thick MR grade plywood with 1.00 mm thick

laminate finish with T.W. border of specified size with

melamine polish. The balance laminate 0.8mm thick to

be provided on inner faces including all materials and

labour etc. complete as per drawing and instruction of

engineer-in charge. Working Table: size : 1500 mm x

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[20] Providing, fixing & Arranging linear workstation as per 4.00 No 36834.07

drawing, framing the skeleton with 18mm + 18mm thick

vertical and horizontal plywood patti both side cover

with 6mm thick plywood for grooving design and

installation, make hole/ face plate for conduit pipes of

eletcrical/ networking cables with openable stud from

horizontal partition vertical support of 18mm + 18mm

thick double plywood cover with 1mm laminate finish

including 18mm thick curvica on exposed edges. Fitted

25mm thick (Partical board, interior grade) post forming

laminated top, fixed with metal clamps including

suspended metal keyboard-mouse tray fixed with

telescopic channel, cable manager and separate drawer

with lock, telescopic channel and box, made from 18mm

plywood with 1mm outside and 0.8mm inside laminate

as well as 18mm post forming outside of shutter with

auto hinges of hafele or equivalent for left or right side.

Drawer run on Ebco make telescopic channel with

Godrej make lock with Two keys. Providing and fixing of

softboard (12mm thick) finished with tapestry of good

quality partition hight 1200 mm. Including all materials

and labour etc. complete as per drawing and instruction

of engineer-in charge. W/S 1200 mm X 750mm x

1050mm with MDU (P.A)

[21] Providing and supply The chair pipe structure of MS 15.00 No 4533.57

CRCA finish 16 gauge round pipe having a diameter of

mm, the understructure frame tubular structure with

stability for proper balance, the seat and back is

supported on spring structure, the backrest armrest and

seat dimensioned and curved from an ergonomics point

of view, the frame and spring-seat structure prepared

from MIG welding process & powder coated, proper high-

density rubber bush provided at all four legs, seat & back

upholstered with fabric.

[22] Blinds assemblies are to be supplied & installed in all 63.00 Sqmt 2147.26

windows with great precision. It should be water

resitant and fitted on alluminium headrails duly power

coated and fitted with stainless steel drive rods. Manual

operated and should have ISI mark.Providing & fixing

roller type window curtains of Deck, Aerolux, Siddhi or

eq. make including same brand channel - chain

mechanism, synthetic black out fabric of approved

colour & design, silver coated backside, same fabric

plated pelmet etc. with all necessary fittings etc.

complete as per Architect/ Site engineer's instructions as

should be as per engineer in charge and chief architect.

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[23] Providing and Arranging book storage having top 18 mm 4.00 No 65014.42

thick MR grade plywood with 4.00 mm thick veneer

melamine polish finish with 0.8 mm balancing

laminate.Shelves made of 12 mm thick clear float glass

with all edge polish. Side and shutter made of 18mm

thick MR grade plywood with 4.00 mm thick veneer

melamine polish finish with 6mm thick clear float glass

and Lock and nylon bullet.louver on bottom made of

solid wood fram for ups exsos including all necessary

fixtures and fastenings as approved, incld. all materials

and labour etc.Complete as per drawing and instruction

of engineer-in charge (with T.W. border patti with

melamine polish) Glass Storage with UPS 1200mm x

[24] Providing and fixing in position partly glazed, partly 169.00 Sqm 3030.00

solid partition work including glass door in Aluminium

frame work using average 450 x 450 mm grid

(horizontally and vertically) comprising of 50 x 50 x

mm Aluminium section and / or as per frame work

shown in the drawing with 12 mm thick all proof

Plywood of IS:710 of approved brand on both sides

finished with 1.0 mm thick laminates of approved shade,

pattern, texture, make and colour as shown in drawings.

Item to include 12 mm thick toughened glass with acid -

frosting/ glass film as per detail design drawings and

100 mm x 40 mm Aluminium vertical member and

mm x 40 mm Aluminium top/ bottom member for glass

door frame to take 12 mm thick toughened glass with

acid frosting work. All exposed T.W. surfaces to be

finished in 2- 2 coats of melamine sealer and polish of

matching laminate colour as directed including all

necessary Stainless Steel finish brass fittings, fasteners,

hardware like door closers/ floor spring, glass locks,

glass door handles of 450 mm length, mortise lock, brass

hinges, door stopper, stopper etc. as per detail design

drawings and wood preservative etc. as per list of

approved material and as approved by the project

Consultant complete in all respect. (Note : In case of false

ceiling, the vertical members to be fixed with RCC slab

ceiling but the area of partition payable will be below the

false ceiling only)

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

[25] Providing & fixing compactor of Base frame fabricated 5.00 No 35350.00

from cold formed channel & angle sections of 10/14

Gauge Thick HRC material and sections Sizes of 25 x

x 25 mm, 25/45 x 100 x 25/45 mm, 45 x 45 mm with

guide rails comprises of solid round shaft of  30 mm

(Bright bar) in ground finish, press fit in to cold formed

'U' channel made from 14 G Thick material completely

grouted within the floor with 0 – 0 levelling having

Nos. of Cast Iron Wheels of Size : 128 X 28mm (moving

on a pair of rails) for units of lengths less than 3540 mm.

All units more than length 3540 mm shall have 6 nos. of

cast iron wheels of size 128 x 28 mm (moving on 3 Nos.

of rails) . The Driving wheel will comprise of a central

hub resting on a pair of roller bearings with 3 insertable

arms engaging into the hub. Boltless type shelves made

of 22 SWG C.R.C.A, quality steel having 8 folds each

designed to carry a U.D.L. of 50 Kgs. Vertical and central

panels made out of 22 SWG mm thick C.R.C.A. The ‘UNI-

LOCK’, or the individual unit lock is a specially designed

mechanism embedded in the hand wheel body itself with

a central lock to enable locking of the entire system with

one key with stoppers on either ends of the rails to

prevent the Compactor unit from moving away from the

rail including all necessary fixture, fastners, fittings,

directed by Engineer Incharge. Approved Make (A)

Compactor Sew Single Face Station Unit :- 2700 x 475 x

Total Rs.

I/We am/are willing to carry out the work at…......................% above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as

Estimated amount put to tender Estimated amount put to

Deduct………% below Add………% Above

In words In words

Description of Item

Item RateIn

(with brief specification and reference to book of Quantity Unit Amount

No. Figure

specifications)

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by

the Engineer-In-Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.:

PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C.

items where there is a change as per actual mix design the cost of difference of cement consumption

have been deducted from the rate of original item at the rate of input rate mentioned in all the

5. Credit of Dismantal Material amount of Rs……NA…. must be recovered from Contractor's R.A Bill.

6. Payment will be given only if the material testing result is satisfactory.Testing of material shall be

done as per statement attached with specification

Dated Signature Deputy Executive Engineer Executive Engineer

the Contractor. R & B Sub Division R & B Division

Nadiad Nadiad