Consruction for Compound wall and paver block work inside Anganwadi Center no. 12 At Indiranagar, Bhavnagar

Excavation for foundation upto 1.5 m depth

including sorting out and stacking of useful

materials in any type of soil and disposing off the

excavated stuff upto any lead.

Boring holes 3.5 m deep in ordinary soil (for cast in

situ piles) and getting out the soil and disposal of

2 the surplus excavated soil as directed within a lead 105.00 300.00 RMT

of 50 Meter for following diameter of pipes.(iii)

Extra for under reaming inside the bore Holes for

3 under reamed piles of following Diameter.(iii) 300 30.00 202.00 EACH

Providing and laying cement concrete 1:3:6 (1-

Cement : 3- Coarse sand : 6- graded stone

4 aggregates 20 mm nominal size) and curing 8.00 3710.00 Cum

complete including cost of formwork in (A)

Foundation and Plinth

Providing laying controlled cement concrete M-250

and curing complete including the cost of form work

5 but excluding the cost of reinforcement for 40.22 6250.00 Cum

reinforced concrete work in GROUND BEAMS /

PLINTH BEAMS /COLUM/FOOTING

Providing laying controlled cement concrete M-250

and curing complete including the cost of form work

6 but excluding the cost of reinforcement for 5.00 7350.00 Cum

reinforced concrete work in COAPING AT ANY

Brick work using common Brunt clay building bricks

having crushing strength not less than

7 Kg./Sqcm. In foundation and plinth in cement 52.00 5800.00 Cum

mortar 1:6 (1cement : 6 fine sand) (B) Conventional

20mm thick sand faced cement plaster on walls

upto height 10 metres above ground level

consisting of 12mm thick backing coat of C.M. 1:3

8 (1-cement : 3-sand) and 8mm thick finishing coat of 417.00 366.00 Sqm

C.M. 1:1 (1-cement : 1-sand) etc. complete.WITH

APPROPTIATE DESIGN AS INSTRUCTED BY

Finishing wall with weather proof Apex exterior

emulsion(plastic) paint on wall surface (two coats)

and one coat of primer to give an required shape

even shade after thoroughly brushing the surface to

9 remove all dirt, and remains of loose powdered 417.00 127.00 Sqm

materials.etc complete The material shall be as

described in list of approved material.shade and

pattern as directed by Architects/City Engineer /

Executive Engineer in charge.

Providing & fixing M.S. grills of required pattern

using M.S. flats, bright bar, hollow MS sactions at

10 required spacing and frame all-round square or 1275.00 127.00 Kg

round bars with round headed bolts and nuts or by

screws. Design and pattern as directed by Architect

Providing TMT Bar FE 500D reinforcement for

11 R.C.C. work including bending, binding and placing 2900.00 88.00 Kg

in position complete upto floor two level

No ITEM QTY RATE UNIT AMOUNT

Providing and fixing pre-cast Rubber Dye / steel

Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed /

vibrated mechanically and as per approved design

Confirming to IS 15658 : 2006 including 35 mm

Sand layer/grit layer for levelling and filling the joint

with sand in proper line and level as per guidlines

of IRC : SP 63-2018 etc.Complete.

13 supplying quary spauls/murrum as selected by EIC. 137.00 378.00 Cum

BMC/ROAD DEPT+/ TENDER WORK-2023-24 / ITEM NO.2

Spreading of quary spuls, murram & machine

BMC/ROAD DEPT+/ TENDER WORK-2023-24 / ITEM NO.5

Rolling and consolidation of soling including filling

15 in depression which occur during the process, with 137.00 8.00 Sqm

power roler 8 tonne to 12 tonne.

BMC/ROAD DEPT+/ TENDER WORK-2023-24 / ITEM NO.6

Supplying & Fixing 600 mm dia hot dip galvanising

cross spiral type razor edge concertina coil having

80 circles, 200 clips with optimum openable

strentch of 8m length using a central core wire high

corbon spring steel (High tensile wire) made up of

2.6mm dia as per IS:4454, Part-1, grade-1-II having

minimum galvanising of 230-250 gsm per mm2

aroung which a edge of razor sharp barbs strip of

5mm thick & 19mm width confirming to IS:513DD

quality having minimum galvanizing coating of

microns with series of barbs punched along the

length at regular interval support / tied with two

rows of barbered runner wires to newly proposed

MS / GI angle brackets at top and one runner wire

at the bottom with U nails & clips etc complete as

per manufacturers specification and directed by

EIC. (The item rate does not include the rate of MS

17 JCB supply as per requirement 45.00 950.00 Hrs

18 Beldar supply 12.00 422.00 no

19 Tractor supply 4.00 1580 per day