PROVN OF HARD STANDING IN FRONT OF BLDG NO. T-24 AND PROVN OF GENERATOR SET FOR AD BDE SIGNAL COY AND ADDN / ALTN TO BDE CONFERENCE HALL, COMPOUND WALL NEAR SIGNAL OFFR LIVING, PROVN OF DRAIN WITH COVER SLAB NEAR OFFR ACCN AND PROVN OF ATTACHED TOILE

Amount

SCH 'A' PART-I : [PROVN OF HARD STANDING IN FRONT OF BLDG NO. T-24 OF AD REGT WKSP AT NABAGRAM MILITARY STATION (MW-16] [Note : Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-I.]

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil, complete all as specified and directed.

Removing excavated soil not exc 50 m and depositing where direcred at a level n.exc 1.5 m above the starting point, complete all as specified and directed. [Total Qty : 39.00 (Part-I) + 2.50 (Part-III) + 34.56 (Part-V) + 4.00 (Part-VI) + 3.00 (Part-VIII) = 83.06]

M&L hard core of broken stone boulder exc 63 mm but n.exc 100 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rolled / rammed to a true surface, complete all as specified and directed. [Total Qty : 39.00 (Part-I) + 1.86 (Part-III) + 1.00 (Part-VI) + 1.40 (Part-VII) = 43.26]

Formwork to edges of rough finished surfaces of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20 cm wide and sides of Reinforced Cement Concrete / Plain Cement Concrete bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide, complete all as specified and directed.

M&L 75 mm thick Plain Cement Concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base of floor, complete all as specified and directed. [Total Qty : 260.00 (Part-I) + 4.00 (Part-VI) = 264.00]

M&L 50 mm thick Plain Cement Concrete (1:2:4) type B1 using 20 mm graded stone aggregate and finished the concrete surface even and smooth using extra cement complete all as specified and directed. [Total Qty : 260.00 (Part-I) + 4.00 (Part-VI) = 264.00]

M&L forming 12 mm thick expansin joints filled with preformed bituminous filler and top 30 mm primed and sealing with sealing compound, grade 'A' on 50 mm thick concrete surface, complete all as specified and directed.

SCH 'A' PART-I : [PROVN OF GENERATOR SET FOR AD BDE SIGNAL COY AT NABAGRAM MILITARY STATION (MW-17)] [Note : (i) Other items of Part-II are clubbed up with Part-I. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-II taking the rate from Part-I.]

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

Excavation post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft / loose soil, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface, complete all as specified and directed. [Total Qty : 18.00 (Part-II) + 8.00 (Part-III) + 2.00 (Part-VII) = 28.00] [Note : Returning filling has done with PCC & measured & paid in respective items of schedule separately.]

M&L Plain Cement Concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed. [Total Qty : 2.55 (Part-II) + 0.64 (Part-III) + 0.30 (Part-VII) + 0.15 (Part-VIII) = 3.64]

S&F Mild Steel roof truss (framed), purlins, posts, cranes, gantries, rails, heavy brackets framing (beam, tee, angle, channel or flat section) including distance pieces cleat etc (Fe 290, Gde E 165), complete all as specified and directed. [Total Qty : 1829.92 (Part-II) + 488.34 (Part-III) + 100.00 (Part-VI) = 2,418.26]

S&F plates (Plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment etc and fixed by riveting or welding or with nut and bolts (including nut and bolts) conforming to Fe- 290-W Grade E- 165, quality B, complete all as specified and directed. [Total Qty : 90.43 (Part-II) + 40.19 (Part-III) + 10.00 (Part-VI) = 140.62]

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws, complete all as specified and directed. [Total Qty : 112.13 (Part-II) + 15.00 (Part-III) + 7.00 (Part-VI) = 134.13]

All as per Item No. 2.06 above but plain sheet, complete all as specified and directed.

M&L brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6), complete all as specified and directed. [Total Qty : 8.34 (Part-II) + 7.36 (Part-III) + 8.58 (Part-IV) + 18.40 (Part-V) + 5.00 (Part-VI) + 3.85 (Part-VII) = 51.53]

M&L rendering 15 mm thick using cement mortar (1:6) on fair faces of brick masonry/conc surface and finished the surface even and smooth without using extra cement, complete all as specified and directed. [Total Qty : 79.43 (Part-II) + 16.00 (Part-III) + 13.00 (Part-VI) = 108.43]

M&L & preparation of newly plastered or unplastered surfaces of wall by applying two coats of cement base paint, complete all as specified and directed. [Total Qty : 79.43 (Part-II) + 9.00 (Part-III) + 184.54 (Part-IV) + 15.00 (Part-VI) + 40.00 (Part-VII) = 327.97]

M&L & preparation of new or previously untreated surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of zinc chrome red oxide primer, complete all as specified and directed. [Total Qty : 76.73 (Part-II) + 19.96 (Part-III) + 3.50 (Part-VI) + 7.00 (Part-VII) = 107.19]

SCH 'A' PART-III : [ADDN / ALTN TO BDE CONF HALL AT NABAGRAM MILITRARY STATION (MW-18)] [Note : (i) Other items of Part-III are clubbed up with Part-I & Part-II. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-III taking the rate from Part-I & Part-II.]

Dismantling stone slabs and tiles of any description of description of thickness in floors, apron laid dry or and pointed, complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc and getting out in soft / loose soil, complete all as specified and directed. [Total Qty : 3.00 (Part-III) + 27.55 (Part-IV) + 45.00 (Part-V) + 5.50 (Part-VI) + 4.00 (Part-VII) + 51.30 (Part-VIII) = 136.35]

M&L plain cement concrete 1:4:8 Type D2 (using 40mm graded stone aggregate) as in foundation, filling mass concrete, complete all as specified and directed. [Total Qty : 0.60 (Part-III) + 1.97 (Part-IV) + 9.00 (Part-V) + 0.50 (Part-VI) + 0.28 (Part-VII) = 12.35]

M&L Plain Cement Concrete 1:4:8, D2 (using 40mm graded stone aggregate) 100 mm thick for paving, sub base path etc., complete all as specified and directed.

M&L Plain Cement Concrete 1:2:4 type B1 (using 20mm graded stone aggregate) 40 mm thick for paving etc., complete all as specified and directed.

Returning, filling-in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft /loose soil, complete all as specified and directed. [Total Qty : 0.50 (Part-III) + 12.13 (Part-IV) + 10.44 (Part-V) + 1.50 (Part-VI) + 1.80 (Part-VII) + 43.00 (Part-VIII) = 69.37]

M&L vitrified ceramic tiles of light shade 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in near cement slurry and pointed in white or coloured cement to match with & including screed bed or bedding layer of cement mortar 20 mm thick in cement mortar 1:6, complete all as specified and directed.

M&L 75 mm thick plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection etc surface finished even and smooth without using extra cement, complete all as specified and directed. [Total Qty : 15.00 (Part-III) + 6.50 (Part-VI) = 21.50]

SCH 'A' PART-IV : [PROVN OF COMPOUND WALL NEAR SINGLE OFFICER LIVING AT NABAGRAM MILITARY STATION (MW-19)] [Note : (i) Other items of Part-IV are clubbed up with Part-I to Part-III. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-IV taking the rate from Part-I to Part-III.]

M&L sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed. [Total Qty : 5.90 (Part-IV) + 1.60 (Part-VI) + 0.85 (Part-VII) = 8.35]

M&L Reinforced Cement Concrete M-25 (Design mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete, complete all as specified and directed. [Total Qty : 9.60 (Part-IV) + 1.50 (Part-VI) + 1.00 (Part-VII) = 12.10]

M&L Reinforced Cement Concrete M-25 (Design mix) using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc, complete all as specified and directed. [Total Qty : 1.85 (Part-IV) + 0.50 (Part-VII) = 2.35]

M&L Reinforced Cement Concrete M-25 (Design mix) using 20mm graded stone aggregate over 1.5 m span, as in lintels, beams, roof beams, cantilever, bressummers, complete all as specified and directed. [Total Qty : 3.42 (Part-IV) + 1.00 (Part-VI) + 0.25 (Part-VII) = 4.67]

Removing Excavated soils exceeding 50metres but not exceeding 250 metres and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and directed. [Total Qty : 15.42 (Part-IV) + 2.20 (Part-VII) = 17.62]

Formwork to side of concrete foundations, footings, bases of columns, raft and raft beams side and soffits (if any) of foundation & plinth beam vertical or to batter and similar type of work in rough finished surface, complete all as specified and directed. [Total Qty : 56.06 (Part-IV) + 6.00 (Part-VI) + 10.50 (Part-VII) = 72.56]

Formwork to sides of column and similar type of work rough finished rectangular in shape, complete all as specified and directed. [Total Qty : 34.44 (Part-IV) + 6.50 (Part-VII) = 40.94]

Formwork to sides and soffits of floor or roof beams, beam haunching, girder, bressummers, lintels, cantilevers, shelves, including supports, overhangs etc. & also splays between floor & beams, finished rough & in flat surfaces etc., complete all as specified and directed. [Total Qty : 34.20 (Part-IV) + 8.50 (Part-VI) + 9.60 (Part-VII) = 52.30]

M&L TMT mild steel bars 10mm dia and over as in reinforcement, cut to length bend to shape required, including cranking bending spirally for hooping for coumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. [Total Qty : 886.56 (Part-IV) + 870.00 (Part-V) + 150.00 (Part-VI) + 895.00 (Part-VII) = 2801.56]

M&L TMT mild steel bars 6 mm to 8 mm dia, cut to length bend to shape required, including cranking bending spirally for hooping for coumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips as in stirrups, complete all as specified and directed. [Total Qty : 526.90 (Part-IV) + 5.00 (Part-VI) + 165.00 (Part-VII) = 696.90]

Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, mixing with liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. [Total Qty : 23.52 (Part-IV) + 19.00 (Part-VII) = 42.52] [Note : Liquid water proofing compound will be measured & paid separately in respective items of BOQ.]

Rendering 15 mm thick with Water Proofing Compound liquid grade in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement, complete all as specified and directed. [Total Qty : 47.46 (Part-IV) + 21.00 (Part-VII) = 68.46] [Note : Liquid water proofing compound will be measured & paid separately in respective items of BOQ.]

Supply only Liquid Integral waterproofing compound, complete all as specified and directed. [Total Qty : 6.35 (Part-IV) + 0.50 (Part-VI) + 1.50 (Part-VII) = 8.35]

M&L & Providing precast cement concrete louvres and jallies, 25 mm thick (measured solid), set in cement mortar (1:4) type B0 (1:2:4) using 20 mm graded stone aggregate including all mouldings but excluding frame, complete all as specified and directed.

SCH 'A' PART-V : [PROVN OF DRAIN WITH COVERED SLAB NEAR OFFICER ACCN AT AD BDE AT NABAGRAM MILITARY STATION (MW-20)] [Note : (i) Other items of Part-V are clubbed up with Part-I to Part-IV. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-V taking the rate from Part-I to Part-IV.]

M&L 10mm thick rendering in Cement Mortar 1:4 on fair faces of brick wk concrete surfaces finished even & fair, complete all as specified & directed.

M&L Plain Cement Concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in bands, string course coping apex stone bed plate kerbs and the like including weathering , slightly rounded or chamfered angle with and incl necessary use and waste of form work complete all as specified and directed. [Total Qty : 2.30 (Part-V) + 0.45 (Part-VIII) = 2.75]

M&L Plain Cement Concrete (1:3:6) type C-1 using 20.mm graded stone aggregate as in benching of drains, surface channel etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered /stopped ends etc. complete all as specified and directed.

M&L precast cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) in landings, cover slabs (for man holes , drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in Cement Mortar 1:4 complete all as specified and directed.

SCH 'A' PART-VI : [PROVN OF ATTACHED TOILET FOR OFFICERS AT AD BDE CAMP OFFICE AT NABAGRAM MILITARY STATION (MW-21)] [Note : (i) Other items of Part-VI are clubbed up with Part-I to Part-V. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-VI taking the rate from Part-I to Part-V.]

PART-VI : B/R PORTION

Dismantling wall and ceiling boards (fibre pulp, insulation etc) or insulation boards /slabs/blankets any thickness, including cover fillets, complete all as specified and directed.

M&L Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded aggregate for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

All as per Item Ser No. 4.09 above, but 5 mm dia and over upto and including 10 mm dia as in stirrups, complete all as specified and directed.

Formwork to rough finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

M&L good quality Earth filling under floor including spreading levelling in layers n.exc 25 cm thick and well rmmming including watering as required, complete all as specified and directed. [Note : Good quality of Earth for filling obtained from excavation can be utilized subject to approval of AGE (I) Nabagram.]

M&L non skid ceramic coloured tiles7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including screed bed or bedding layer of mortar 15 mm thick for laying floor tiles using Cement Mortar (1:6), complete all as specified and directed.

M&L glazed ceramic tiles 450 x 350 x 7 mm tk set and jointed in neat cement slurry and pointed in white or colour cement over 10 mm backing coat using cement mortar 1:4 complete all as specified and directed.

S&F 20 mm thick granite (of any type) machine cut, in skirting/ dado laid over 15 mm thick screed bed (1:6) and jointed with grey cement slurry, and pointed with white cement with with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in Cement Mortar (1:6), complete all as specified and directed.

M&L rendering 10 mm thick with Water Proofing Compound using Cement Mortar (1:4) on fair faces of brick masonry/conc surface and finished the surface even and smooth without using extra cement, complete all as specified and directed. [Note : Water proofing compound wiil be measured and paid separately.]

S&F mild steel bolts with hexagonal or square head one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square not exc 10 cm long n.exc 15 cm long dia metre of neck exceeding 11 to 15 mm complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distempering over one coat of chalk whiting as preparatory to distemper complete all as specified and directed.

S&F Aluminium Anodised Frame work (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge, complete all as specified and directed.

S&F sheet glass 4 mm thick ordinary quality glazing with metal frame in square n.exc 0.5 sqm in each panes, complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and averaging width of aperture 1.40 mm and fixed with tinned tacks, or galvanixed staples to metal / wooden frame complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification, complete all as specified and directed.

S&F factory made solid PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plaint colour PVC sheets for top rail, lock rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F Butt hinges, of size 100 mm length extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type C-22, complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150 mm long, complete all as specified and directed.

S&F aluminium anodised handles of size 150 mm, complete all as specified and directed.

S&F vitreous china wash hand basin, oval type size 600 x 480 mm white including CP pillar tap, PVC waste pipe etc and cutting for and pinning in ends of brackets or erecting stands or fixed on Reinforced Cement Concrete slab etc complete all as specifed and directed.

S&F Vitrious china urinal half stall type white including waste pipe complete, providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and inclding 60 mm long brass screws, pointing around urinal back in cement with brackets flush pipe grating and union for discharge pipe, complete all as specified and directed.

S&F vitrious china EWC, white including PVC seat cover including fixing with floors/ walls including all necessary screws, bolts etc complete all as specifed and directed.

S&F 10 lit capacity PVC valveless, syphomic action, flushing cistern, low level, white with inlet, ball valve, float and handle, including bracket, flush pipe etc connected to the EWC complete all as specifed and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F health faucet chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and CP wall hook includig making connection and fixed in position, complete all as specified and directed.

S&F stop valve 15 mm, fancy type chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F bib tap, 15 mm, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

M&L 75 mm PVC floor trap, plain with grating including jointing with solvant cement etc complete all as specified and directed.

M&L cast iron nahani trap 100 dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F cast Iron 100 bore 'P' or 'S' trap including jointing to EWC, waste pipe etc and fixed in cement concrete type B1 (1:2:4), complete all as specified and directed.

M&L PVC (SWR), gully trap, 125 mm, setting and jointing with waste pipe, solvent cement complete all as specified and directed.

S&F tubular towel rail, 20 mm dia brass chromium plated, D type, 60 cm long between flanges, complete all as specified and directed.

M&L UPVC pipe 20 mm bore of pressure rating 10 Kgs/sqcm fixed complete to walls, ceilings or in floors etc including necessary brass fittings like elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc complete all as specified and directed.

M&L reinforced concrete pipes of bore 150 mm, class NP 2, laid and jointed complete with collers, complete all as specified and directed.

Cutting into existing manholes for connecting 150 mm bore new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified and directed.

All as per Item No. 6.38 above but for 100 mm bore pipe, complete all as specified and directed.

M&L reinforced concrete pipes of bore 100 mm, class NP 2, laid and jointed complete with coller, complete all as specified and directed.

PART-VI : E/M PORTION

M&L point wiring of any length using approved colour coding as per IS, with stranded copper conductor 1.5 Sq.mm (Nominal area), single core, PVC insulated and unsheathed stranded FRLSH cable 1100 volts grade, ISI - 694 marked, in PVC rigid conduits heavy duty ISI marked totally concealed in wall/floor/roof including all accessories etc. with sunken boxes suitable for mounting switches/sockets etc. and PVC insulated stranded copper conductor 1.5 Sq.mm single core cable as earth and connecting to common earth dolly complete all as specified for the following:-

[Note- (i) Cutting in chases and pointing in will be done by contractor without any cost. (ii) Making good of distrubed surfaces matching with existing finishes will be done by contractor without any extra cost.]

All as per Item No. 6.42 to 6.43 here-in-above & One light point controlled by one, One-way switch complete all as specified and directed.

All as per Item No. 6.42 to 6.43 here-in-above but One fan point controlled by one, One-way switch complete all as specified and directed.

All as per Item No. 6.42 to 6.43 here-in-above but One 5 pin 5 Amp Socket outlet point on same board with other switches including earth wire complete all as specified and directed.

All as per Item No. 6.42 to 6.43 here-in-above but One 5 pin 5 Amp Socket outlet point on independent board complete all as specified and directed.

All as per item No. 6.42 to 6.43 here-in-above but with 2.5 Sqmm (Nominal area), single core, PVC insulated and unsheathed stranded FRLSH cable 1100 volts grade, ISI - 694 marked, including PVC insulated stranded copper conductor 2.5 Sqmm single core cable as earth and connecting to common earth dolly complete all as specified for one 15 amps socket outlet point on independent board. [Note:- Making good of disturbed surfaces will be done by contractor without any claims.]

S&F piano switch, flush type, 5 Amps single pole complete all as specified and directed.

S&F multipurpose socket outlet, flush type, 3 pin, 5 Amps complete all as specified and directed.

S&F switch socket combination, 2 in 1, 3 pin 6 & 16 Amp flush type complete all as specified and directed.

S&F ceiling rose surface type three terminals complete all as specified and directed.

S&F MCB, Single pole, rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,C- curve complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Energy efficient, sturdy engineering plastic Exhaust fan, plastic body AC single phase, Operating voltage 220-240 Volt, frequency 50Hzs, having blade sweep 250 mm, 1200 rpm speed, minimum 860 cmh air flow, supply complete with louvers and frame fixed with suitable size GI bolts, nuts and washers duly grouted and connecting up with 0.75 Sqmm size 3 core PVC insulated flexible cable with multistranded copper conductor from ceiling rose to connector of exhaust fan, complete all as specified and directed. [Note : Purchase voucher and warranty certificate to be produced for claiming of payment.]

S&F LED based security light 35 W in aluminium pressure die cast housing with touched glass cover having IP 66 Protection and with aluminium bracket including taking down of old unservicable security light complete all as specified and directed.

SCH 'A' PART-VII : [PROVN OF GATE AT AD BDE OFFRS MESS AT NABAGRAM MILITARY STATION (MW-22)] [Note : (i) Other items of Part-VII are clubbed up with Part-I to Part-VI. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-VII taking the rate from Part-I to Part-VI.]

PART-VII : PAVING

Surface dressing n.exc 15 cm deep in soft/ loose soil, complete all as specified and directed.

M&L 100 mm thick Plain Cement Concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and directed.

M&L Plain cement concrete type B-0 (1:2:4) using 12.5 mm graded stone aggregate as in rounded or chamfered on edging complete all as specified and directed.

PART-VII : B/R ITEMS

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches pillars, etc complete all as specified and directed.

M&L forming mortice holes, exc 50 but n.exc 100 cu cm for balusters, newels, rag-bolts etc and grouting with cement mortar 1:2 after balusters, etc are fixed complete all as specified and directed.

S&F framed work (Fe 290, Gde E 165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L applying one coat of cement base paint on old plastered / unplastered surfaces of walls complete all as specified and directed.

SCH 'A' PART-VIII : [PROVN OF STREET LIGHT WITH SWAGED POLE ALONG THE ROAD AT AD REGT AT NABAGRAM MILITARY STATION (MW-23)] [Note : (i) Other items of Part-VIII are clubbed up with Part-I to Part-VII. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-VIII taking the rate from Part-I to Part-VII.]

M&L good quality, dirt less, clean, dry river Sand cushioning / Sand covering using Tibba sand for underground cable protection complete all as specified and directed. [Note : For the purpose of payment, maximum only punned thickness which will be 18 cm will be measured & paid as per site measurement.]

Supply and laying Sub Class "B" Bricks Designation 75 as in cable Protection of size 250mmx125mmx50mm complete all as specified and directed.

S&F Galvanised Iron Pipe light grade 80 mm bore with necessary accessories / fittings bracing with pole / wall by FI clamps made with 32x6mm for cable protections / pole for crossing of culverts / nallah and all as specified and directed.

S&F Galvanised Iron Pipe light grade 40 mm bore with necessary accessories / fittings bracing with pole by FI clamps made with 32x6mm for cable protections / pole for crossing of culverts / nallah and all as specified and directed.

Supply and errect steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-37 (9.5 metres long) including 1mtr 40mm dia bracket mount on pole top complete all as specified and directed. [Note : Payment will be done after production of original purchase voucher & manufacturer's test certificate duly vetted by Engr-in-Charge.]

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with 1100 volts grade with stranded aluminium conductor 16 X 4 Sqmm, complete all as specified and directed.

S&F 70 watt LED street light fitting made up of pressure die cast aluminum housing with toughened glass and high powered individual LEDs with secondary optics, constant current driver with in built protection against lightning ,over voltage & short circuit, IP66 Protection and fixing on 40 mm dia of bracket complete all as specified and directed.

S&F distrubution board 32A, 3 pole, 230 volts Digital time switch complete installed in 350 X 350 X150mm with size and 2mm thick CRCA sheet outdoor type panel for timer mounted on angle iron stand fixed at 75 cm from the ground level made out of angle size 50 X 50 X 6 mm grouted in PCC 1:3:6. complete all as specified and directed.

S&F PVC insulated, sheathed weather proof, copper conductor of size 1.5 sqmm, 3 core complete all as specified and directed.

S&F FRP Junction box with front cover of size 250x250 x 160 mm (FRP) for street light pole with locking arrangement with IP 66 protection with 32 Amps 4 way heavy duty terminal block with 10A MCB SP with two steel bracket to fix with pole and aluminium bus bar of rating 100 Amps complete all as specified and directed.

M & L earthing complete with galvanized steel earth plate electrode of 60 cm X 60 cm X 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized Iron earth strip 25 X 4 mm thick by means of nuts bolts washers etc as earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel, galvanized iron pipe light grade 15 mm diameter for protection of earthing

Item No. 8.11 Contd.... wire,(To be concealed in wall/floor) connected to earthing test point, all as shown in electrical plate No. 3 of MES Schedule Part I. , connected to earthing test point including testing on completion, excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep with a PCC (1 3 6) type C1 using 20mm graded stone aggregate earth chamber ,40mm thick RCC cover type

Item No. 8.11 Contd.... B1 (1 2 4) B1 using 20mm graded stone aggregate with 8 mm dia tor reinforcrment 100mm c/c and 12 mm dia MS bar handle on top of cover on ground level, 20 mm dia GI watering pipe, funnel, etc. complete and testing resistance in completion all as shown in electrical plate no. 3 connected to the earthing test point, all as specified and directed.

Cutting the road / hard standings and excavating in trenches not exceding 0.40 mtr wide and not exc 0.80 mtr deep across the road for laying cable including making good the excavated portion by means of Plain Cement Concrete 1:2:4, type B1 using 20mm graded stone aggregate complete and matching with the surroundings complete all as specified and directed.

SCH 'A' PART-IX : [PROVN OF FIBER SHEET WITH LOOPHOLES FOR GATE NO. 03 OF NABAGRAM MILITARY STATION (MW-24)] [Note : (i) Other items of Part-IX are clubbed up with Part-I to Part-VIII. (ii) Abstract for MB Entry / RAR / Final Bill will be prepared separately for Part-IX taking the rate from Part-I to Part-VIII.]

M&L affix Solid PVC sheet on the street/ iron gate frame consisting of minimum 3mm thick Plain/ Colour PVC sheet, self coloured in plain shades by blending suitable pigments with PVC resin. The sheets will have silky matt surface finish free from any blistering, colour blots, creasing, pin holes, etc. The density of the sheets shall be min 600 Kg/Cum, and all are inclusive fixing arrangement including splayed edges, notchings, allowances for overlaps and passings at angles, batteries, strutting, bolting, clamping, nailing, welding, wedging, etc. to the steel/ iron frames complete all as specified and directed.

S&F of framed brackets of angles or trees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, rivetting, etc. conform to Fe-290, Gde-165, complete all as specified and directed.

Abida Enterprises (BID ID -3281667)

A.R. ENTERPRISE (BID ID -3285374)