CONSTRUCTION OF SPECTATOR STAND and PARKING AT ROSHNABAD, HARIDWAR.

Amount

DSR Item No.- 2.32 Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.

DSR Item No.- 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

DSR Item No.- 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

DSR Item No.- 2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

DSR Item No.- 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DSR Item No.- 4.1.4 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

DSR Item No.- 4.1.5 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR Item No.- 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

DSR Item No.- 2.35.3.1 Providing and applying Antermite treatment in floor plinth with Chloropyriphos/Lindane E.C. 20% with 1% concentration.

DSR Item No.- 5.33.1 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer -in - charge. All works upto plinth level

DSR Item No.- 5.33.2 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer -in - charge. All works above plinth level upto floor V level

DSR Item No.- 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

DSR Item No.- 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

DSR Item No.- 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

DSR Item No.- 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

DSR Item No.- 5.9.3 Suspended floors, roofs, landings, balconies and access platform

DSR Item No.- 5.9.7 Stairs, (excluding landings) except spiral staircase

DSR Item No.- 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars

DSR Item No.- 6.2.2 Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR Item No.- 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in: Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR Item No.- 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

DSR Item No.- 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

DSR Item No.- 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

DSR Item No.- 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix 1:6(1 cement: 6 fine sand)

DSR Item No.- 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

DSR Item No.- 13.3.1 20 mm cement plaster of mix : 1:4 cement mortar (External Walls)

DSR Item No.- 13.21 Extra for providing and mixing water proofing material in cement of plaster work in proportion recommended by the manufacturers.

DSR Item No.- 13.48.1 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications. Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr / 10 sq

DSR Item No.- 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

DSR Item No.- 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

DSR Item No.- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable

DSR Item No.- 13.85.1 Applying priming coats with primer of approved brand and manufacture, With ready mixed pink or grey primer on wood work (hard and soft wood).

DSR Item No.- 11.3.1 Cement concrete flooring 1:2:4 (1 cement :2 coarse sand:4 stone aggregrate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc complete. 40mm thick with 20mm nominal size stone aggregrate

DSR Item No.- 11.13.1 Providing and fixing glass strips in joints of terrazo / cement concrete floors. 40mm wide and 4mm thick

DSR Item No.- 11.23.5 Marble stone flooring with 18 mm thick marble stone, as per sample of marble apporved by Engineer-in-charge, over 20mm &(average) thick base of cement mortar 1:4 laid and jointed with Udaipur green marble

DSR Item No.- 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

DSR Item No.- 11.40 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

DSR Item No.- 11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

DSR Item No.- 11.25 Extra for marble stone flooring in treads of steps and risers using single

DSR Item No.- 11.24 Extra for prefinished nosing in treads of steps of stone / sand stone slab

DSR Item No.-11.56.1 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

DSR Item No.- 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

DSR Item No.- 9.1.2 Providing wood work in frames of door , window, celestory windows and other frames,wrought framed and fixed in postion with hold fast lugs or with dash fastners of required dia & length (hold fast lugs or dash fastners shall be paid for separately). Sal wood

DSR Item No.- 9.20.1 Providing and fixing ISI marked flush door shutters confirming to IS : 2202(PART I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains of cross bands and face veneers on both face of shutters. 35 mm thick including ISI marked stainless steel butt hinges with necessary screws

DSR Item No.- 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

DSR Item No.- 9.72.2 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x70x4 mm (ordinary type)

DSR Item No.- 9.74.1 Providing and fixing bright finished brass tower bolts(barrel type) with necessary screw etc,complete. 250x10

DSR Item No.- 9.75.1 Providing and fixing bright finished brass door latch with necessary screws etc. complete :300x16x5 mm

DSR Item No.- 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

DSR Item No.- 9.81.1 Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

DSR Item No.- 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

DSR Item No.- 21.3.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. With float glass panes of 8 mm thickness

DSR Item No.- 21.1.2.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

DSR Item No.- 21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. With float glass panes of 5.50 mm thickness

DSR Item No.- 21.17 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

DSR Item No.- 21.11.1 Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin-charge complete. 205x19mm

DSR Item No.- 21.15.2 Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete. Powder coated minimum thickness 50 micron aluminium

DSR Item No.- 21.16.2 Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineerin-charge. Powder coated minimum thickness 50 micron aluminium

DSR Item No.- 21.4.1 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body/plate with doubdle spring mechnism and door weight upto 125 kg, for doors including cost of cutting floors, embeddings in floors

DSR Item No.- 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like

DSR Item No.- 22.15 Providing and laying in situ seven course water proofing treatment with AAP (Atactic poly-prolene) modified Polymeric memberane over roof With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

DSR Item No.- 12.41.2 Providing & fixing on wall face un plastered Ridge PVE rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion single socked pipe 110 mm diameter

DSR Item No.- 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

DSR Item No.- 10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

DSR Item No.- 12.29 Providing and fixing false ceiling with 12 mm thick plain/ semi perforatedor with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminium primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodised aluminium (with 15 micron anodic coating) Tsections 35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminium frame work shall be paid separately).

NSI Imported GRABO 4MM thick (as per quote attached)

DSR Item No.- 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

DSR Item No.- 18.8.4 32 mm dia.

DSR Item No.- 18.8.3 25 mm dia.

DSR Item No.- 18.8.2 20 mm dia.

DSR Item No.- 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK.

DSR Item No. 18.9.6 50 mm dia.

DSR Item No. 18.9.5 40 mm dia.

DSR Item No. 18.9.4 32 mm dia.

DSR Item No. 18.9.3 25 mm dia.

DSR Item No. 18.17 Supply, installing, testing and commissioning of ISI marked Gun Metal gate valves screwed pattern conforming to IS 778 class 1 including gate valves screwed pattern conforming to IS 778 class 1 including jointing, supporting etc complete and as directed.

DSR Item No. 18.17.4 50 mm dia. - Gate Valves

DSR Item No. 18.17.3 40 mm dia. - Gate Valves

DSR Item No. 18.17.2 32 mm dia. - Gate Valves

DSR Item No. 18.17.1 25 mm dia. - Ball Valves

Supply, laying , testing & commissioning of UPVC-SWR pipes conforming to IS 13592/92 and fittings conforming to IS-14935/99, cutting the pipes to required lengths, laying in position to required grade and level, jointing, making holes, pockets, chases in walls, floors of all types and making good the same, testing and rectifying leakages for concealed piping within toilet blocks, sunken slab, plinth etc. complete and as directed.

NSI 110 mm dia.

NSI 80 mm dia.

NSI 40 mm dia

NSI 32 mm dia

Supply, laying, testing & commissioning of UPVC-SWR pipes conforming to IS 13592/92 and fittings conforming to IS-14935/99, cutting the pipes to required lengths, laying in the position to required grade and level, jointing, supporting with cleat / clamp / bracket support, testing and rectifying leakages for piping within vertical shafts / supported on wall / hung below slab etc. complete and as directed.

NSI 250 mm dia.

NSI 110 mm dia.

NSI 75 mm dia.

Supply, laying, testing & commissioning of Heavy duty ISI marked Floor Drain / Nahani trap & Clean Out Plug with approved make heavy duty, round or square SS grating etc. complete and as directed

NSI 250 mm dia. Outlet Floor Drain (F.D) at Terrace Floor, (Indore Sport comp)

NSI 110 mm dia. Outlet Outlet Floor Drain (F.D) & C.O.P ( 2 + 2) respectively.

NSI 80 mm dia. Outlet Nahani Trap , P. Trap & C.O.P (142 + 21 + 4) respectively. Providing & fixing vent cowl / guard / balloon with wire on terrace including jointing etc. complete.

Providing and fixing PVC Pipe.

NSI P 110 mm dia

NSI 80 mm dia

DSR Item No. 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

DSR Item No. 17.5.1 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 510x1040 mm bowl depth 250 mm

DSR Item No. 17.7.8 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. Brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers

NSI Installation, testing and commissioning of shower assembly including overhead rose Shower with revolving joint pattern and concealed 4 way single lever diverter having built-in non return valves with wall spout of 15mm x 150mm long including connecting inlet and outlet to main piping, cutting and making good the walls etc. complete and as directed.

NSI Providing and Fixing in position storage type storage water heater capacity 50 liters ‘ mild steel body Sphere hot’ ‘Venus’ ‘Racold’ or other approved make and horizontal wall mounted type including making water connections with stop cocks, pressure reducing valve if required, safety pressure release valve etc. complete.

DSR Item No. 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

DSR Item No. 17.34.1 Providing and fixing toilet paper holder : C.P. brass

DSR Item No. 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

DSR Item No. 18.15.2 Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

NSI Installation, testing and commissioning of 15 mm dia CP. brass ablution tap with hose union and CP. wall flange of approved quality.

NSI Installation, testing and commissioning of 15 mm dia CP. brass. Hand Spray or Jet spray with C.P. pipe connection and 15 mm C.P. angle stop cock.

DSR Item No. 19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

DSR Item No. 19.1.1 100 mm dia.

DSR Item No. 19.1.2 150 mm dia.

DSR Item No. 19.1.3 200 mm dia.

DSR Item No. 19.4 250 mm dia.

DSR Item No. 19.30.3.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR Item No. 19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supply, laying, testing and commissioning of 230 mm thick BB masonry rectangular Storm Water Chamber of a depth of 1.0 m, 150 mm thick bedding in CC 1:2:4 inside and outside plaster in cm 1:3, C. I. rungs weighing 5.2 kg each, C. I heavy duty frame and cover of size 0.9 x 0.9 m weighing 125 kg including excavations, dewatering shoring and strutting, backfilling etc complete as directed.

NSI Size 900mm x 600mm

NSI Size 900mm x 900mm

DSRI Item No. 19.35 Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc.

DSR Item No. 19.35.1 450 mm dia RCC pipes.

DSR Item No. 19.35.2 600 mm dia RCC pipes.

DSR Item No. 19.13.1.2 2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement. With Sewer bricks conforming IS : 4885 each

DSR Item No. 19.11.1.2 Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : With Sewer bricks conforming IS : 4885

DSR Item No. 18.12.8 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work. 80 mm dia.

NSI 'Supply, laying, testing and commissioning with bitumastic hessian cloth over two coats of anti-corrosive paints of G. I. heavy duty "C" class pipes. 80 mm dia.

NS Design, supply, erection, testing and commissioning of 04 Nos high mast LED Sports lights including lights, mast, mast foundation, electrical cabling, central/pole control panel, rider and all accessories etc., complete, required for proper completion of work, as per illumination (>2000 lux) requirements of televised casting national games level hockey ground. The lights, mast, founadations all have to be designed from recognized sports light and structural designers (including vetting from ISLE / IIT or equivalent institution / organization). The high mast (tentative hight approximately 35 M, but final hight as per design) having polyster powder paint with rope and foundation (as per design) is made up of two/three or more sections jointed by nuts & bolts. No welding shall be applied while jointing the section of poles. Including Copper Earthing with aviation Light and Lightning Arrestor complete as required. Supply and installation (tentative approximately 75000 Lumens, 500 W, 40 No flood lights on one pole/mast, but final lumens/lux/W/No of luminaries as per design) in outdoor stadium with Glare Free Sports Lighting Fixtures of Bajaj/Phillips or equivalent brand and manufacturers with approval of Engineer-in-Charge. (See other details in specifications.)

NS Supplying, erection, testing and commissioning of steel pole of 9 meter height, coated with polyster powder with high U.V & corrosion resistance, bracket length of 400mm long including 100W LED Light built in prewired control box with service door including lock and safety chain, supplying and fixing of 6 Amp SP MCB C-Series and 32 Amp heavy duty connector etc. for making connections with suitable size of copper wire and thimbles / lugs in the connector box, base plate of 200mm x 200mm x 12mm thick, bolt size 4 nos M16 nut and bolt, bolt length 300mm. The pole shall be installed in cement concrete foundation (1:3:6) i.e. 1 cement, 3 coarse sand and 6 graded stone with the help of anchor bolts of 3/4" dia by laying iron bar mesh fabricated with 6mm dia iron bar, earthing of pole, connection etc. complete as required.

DSR Item No. 18.60.1 Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80 mm dia nominal bore

DSR Item No. 18.37.1 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat. With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

DSR Item No. 6.1.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

DSR Item No. 6.12.2 Half brick masonry in common burnt clay building bricks in cm 1:3 (1 cement 3 sand) using second class bricks in foundation and plinth Baffle walls

DSR Item No. 13.10 15 mm cement plaster 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.Walls

DSR Item No. 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

NSI Providing and fixing cast iron cowl including carriage of material upto all leads and lifts

NSI Supplying & fixing 560 dia SFRC cover & frame heavy duty

SOR Item No. 1126021 Miscl. Providing and spreading RBM i.e., River Bed Material (treated asz granular sub-base /base/surface course material) in uniform layers with motor grader on prepared surface with rotavator and compacting with smooth wheeled roller to achieve the desired density.

SOR Item No. 11257811 (Mord) Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundatins and floors including supply of all material, labour and T&P etc. required for proper completion of the work (Based on PWD specifications).

DSR Item No. 16.68 Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in reuired colour and pattern over and inlcuding 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charges.

MORD/SOR Item No. 12-5-2-1 Plaing/reinforced cement concrete in substructure complete as per drawings and techinical specification clause 802, 804, 805, 806, 807, 1202 and 1204 P.C.C grade M 20 Nominal mix (1:2:4) upto 5m height.

MORD/SOR Item No. 10-8 Painting lines, Dashes Arrows, etc. on road in Two Coats on New work sqm Painting lines, dashes, arrows, etc. on road in two coars on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification clause 1702.

DSR Item No. 2.28 Surface dressing of the ground inlcuding removing vegetationa and inequalities not exceeding 15 cm deep and disposal of fubbish, lead upto 50 m and lift upto 1.5 m. All kinds of soil

DSR Item No. 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

SOR Item No.- 11-1-1-1 Excavation for structures earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting our, construction of shoring and bracing, removal of stumps of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material ordinary soil.

SOR Item No.- 12-3 Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification clauses 613.4 & 1204.

DSR Item No. 5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR Item No. 5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

SOR Item No.- 3-4 R&B Construvtion of embankment with approved material obtained from borrow pits (including cost of compensation for earth taken from private land) with a lift upto 1.5 m, transporting to site, speading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per materials by mechanical transport including loading, unloading upto 3 km lead.

SOR Item No.- 4-7-1-B R&B WBM Gradng 1 Provinding, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, stone acreening/binding materials to fill-up the interstices of the required density Grading 1 as per Tachnical Specification Clause 404. by Mechanical Means,

SOR Item No.- 2-2 MIS Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundation and floors including supply of all matarial, labour and T&P etc. reqired for proper completion of the work. (Based on PWD specifications)

MORD/SOR Item No.- 11-5-2 Brick work with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in superstrucure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)

MORD - 11-1-1 Earthwork in excavation for structures as per drawing and technical specifications Earthwork in excavation for structures as per drawing and technical specifications stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.Upto 3 m depth(for RCC Pipe excavation)

MORD - 11-1-2 Earthwork in excavation for structures as per drawing and technical specifications Earthwork in excavation for structures as per drawing and technical specifications stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.Upto 6 m depth

MORD - 9-3-A Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in double row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1106.1200 mm dia

MORD 11-4-2-1 Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C grade M 15

NSI Item Design, Providing, Fabricating, Assembling, Painting, Hoisting and Erecting in position including detailing of Primary Steel Structure MS RHS/SHS/CHS/Plates of thicknesses as per structural design or static analysis conforming to relevant IS code. Fabrication of structural elements shall be done using ARC/SAW/MAW welding process. Including transportation, cutting, threading, machining, all leads and lifts up to all heights, tools and plants and necessary scaffolding etc. required for all operations/hoisting/working. All structural members shall be painted with first coat of Epoxy Primer minimum 30 micron. Over primer, Epoxy Paint minimum 80 microns thick to be applied in two coats. Including Designing, Detailing, Providing, Fixing, Fabrication, Assembling and Erection of Roofing Material as per structural design or Non Linear Analysis, maintaining a minimum safety factor of Safety Coefficient of 4. Roofing Material Fabric should have perfect strength, inner reinforcement and water resistant coatings to withstand extreme wind/storm pressure, weathering effect of sun and rain (e.g., PES PVC Coated Fabric with both side PVDF lacquered/Coated, Weight 1200 gsm, Tensile Strength 5000/4300 N/5cm, Tear Resistance 600/500 N , FR Retardant B1.) This work shall including all material, patterning, forming, cutting, clamping, seaming, welding, fixing and installation with GI cables (thickness as per Design/Analysis), flashing, SS Swage End, Galvanized Membrane Plate with Paint as per Spec. etc. complete required for proper completion of work as per direction of the Engineer-in-Charge. Seam should be Single Stroke & minimum Width 50mm. Standard Warranty on Roofing Material should be 20 Yrs from Roofing Material Manufacturer/Supplier.

DSR Item No. 8.18.1.1 Stone work (machine cut edges Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately).Kota stone slabs exposed face dressed and rubbed. 25 mm thick

DSR Item No. 1.10.2 Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required. Group-B

DSR Item No. 1.12 Wiring for light/ power plug with 2x4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

DSR Item No. 1.14.1 2X1.5 sq.mm. + 1X 1.5 sq.mm earth wire

DSR Item No. 1.14.2 2X2.5 sq.mm. + 1X 2.5 sq.mm earth wire

DSR Item No. 1.14.4 2X6 sq.mm. + 1X 6 sq.mm earth wire

DSR Item No. 1.14.5 2X10 sq.mm. + 1X 10 sq.mm earth wire

DSR Item No. 1.18.2 S/L following 2 pair, 0.5 sq mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing PVC conduit as required.

DSR Item nO. 1.19 S/L co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing PVC conduit as required.

DSR Item No. 1.11 Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, 2 way modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc

S/F of following sizes of PVC conduit along with accessories in surface/recess including cuttting the wall and making good the same

DSR Item No. 1.21.1 (20mm)

DSR Item No. 1.21.2 (25mm)

DSR Item No. 1.32 S/F suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and flxing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required

DSR Item No. 1.31 S/F suitable size GI box with modular plae and cover in front on surface or in recess, including providing and flxing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc. as required.

DSR Item No. 1.38 S/F call bell/ buzzer suitable for D.C/A.C single phase, 230 volts, complete as required.

DSR Item No. 2.8.7 S/F way, three pole and neutral, prewired, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with loose wire box, terminal blocks, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted i/c earthing etc. as required. (But without MCB /RCCB/lsolator) 8 way (4 +24), Double door,

DSR Item No. 2.10.2 S/F 5 amps to 32 amps rating, 240 volts, 'C' series, miniature circuit breaker suitable for lighting and other loads Single pole and neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required..

DSR Item No. 2.13.1 40 amps

DSR Item No. 2.13.2 63 amps

DSR Item No. 5.4 Earthing with G.I earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

DSR Item No. 5.7 S/L 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

DSR Item No. 1.25 Supplying and fixing stepped type electronic fan regulator on the existing plate switch box including connections all as dirceted.

DSR Item No. 1.33 S/F 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

DSR Item No. 1.34 S/F brass batten/angle holder i/c connection etc. as required.

S/F following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. as required.

DSR Item No. 1.24.1 5/6 amps switch

DSR Item No. 1.24.4 3 pin 5/6 amp socket outlet

DSR Item No. 1.24.6 Telephone socket outlet

DSR Item No. 1.24.7 TV antenna socket outlet

DSR Item No. 1.22.1 S/F metal box of 75mmx75mmx60mm deep on recess with suitable size of phenolic laminated sheet cover in front including painting etc. required

DSR Item No. 1.40 P/L plain 16/0.20 mm twin, FR PVC insulated, PVC flat flexible copper cable on the floor/ wall, or side of the table/ door etc. as required.

A/R Supplying,fixing& Installation of LED lamp 20 watt (Crompton/Havells make)

A/R Supply & Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting (Type T5)of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.(Crompton/Havells make)

A/R Supply & Installation of exhaust fan in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required. Orient Make upto 300 mm sweep

A/R P/F bracket Light (Crompton/Havells make) with lamp

A/R S/F, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required. (1200 mm sweep) Orient/Bajaj make Model NEW BREEZE.

A/R Supply and fixing of Mirror light 1x10Watt ,Model No. LCL-10-CDL,Make Crompton/Havells

A/R S/F of Decorative Ceiling light fittings with thermoplastic High Impact Compact fitting in CFL 18 watt complete all in respect.Make Crompton/Havells

10.18 DSR CIVIL P/F Hexagonal MS sheet fan box for ceiling fan clamp od internall dia 140mm, 73mm height top lid of 1.5mm thick MS sheet with its top surface hacked, MS clamp shall be made of 12mm dia MS bar bent to shape as per standard design.

DSR Item No. 2.11 S/F single pole blanking plate in the existing MCB DB complete etc. as required. (5 no. /MCBDB)

DSR Item No. 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..

DSR Item No. 5.5 EARGIPL Cu earth plate elctrode:Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosurewith cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

DSR Item No. 5.8 EARG125X6 S/L 25 mm x 5 mm Copper strip in ground:Supplying and laying 25 mm X 5 mm Copper strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50 mm)

DSR Item No. 5.9 EARG125X6 S/L 25 mm x 5 mm G.I. earth strip in ground:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)

DSR Item No. 10.5.3 Supplying and making outdoor cable and termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required.240 sq. mm

DSR Item No. 12.39 Supplying and fixing of light class G.I. pipe of 100 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required.

DSR Item No. 11.3.2 Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.Above 6.5 meter and upto 8.0 meter

DSR Item No. 11.5 Providing and making steel pole collar with cement concrete (1 cement : 3 coarse sand : 6 stone aggregate 20 mm) of specified size and shape including form work, plastering if required, curing etc. as required. (volume of pole/ pipe not to be deducted)

DSR Item No. 13.1 Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

DSR Item No. 13.7 Supplying of two lengths of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) double pole cross arm for three wire 11KV over head line conductors complete with through bolts and nuts for clamping to the poles, 50 mm X 6 mm M.S. flats welded on one side to the channel iron and with bolts and nuts on the other side for tying the cross arms together, including drilling holes for insulator pins/ fittings, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.

DSR Item No. 13.8 Supplying and erection of a set of cross bracing FRLSame work for 11 KV over head line double pole structure having four members fabricated out of 50 mm X 50 mm X 6 mm angle iron to form a rectangle of minimum size 1400 mm width X 2500 mm height , complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc (as per drawing) and painting with primer and finish paint as required.

DSR Item No. 13.9 Erection of double pole 3 wire cross arm for 11KV/ 22KV/ 33 KV over head lines as required.

DSR Item No. 13.1 Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

DSR Item No. 13.11 Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

DSR Item No. 13.13 Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

NS 4c x25 sq.mm cable

NS 4c x16 sq.mm cable

NS 4c x10 sq.mm cable

NS 4c x 4 sq.mm cable

NS SITC of 4x25 sq.mm Al Armoured cable along the rope of high mast

NSI SITC of 4 sqmm,single core copper wire

Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing,Painting,Earthing,Numbering,Danger plate etc. Compleete as requried,numbering, danger plate etc. complete as required as per specification and drawing.SMDB-(ADMIN BLOCK)INCOMER:1 nos. 63A 415V, Ics=25KA, 4P MCCB with TM release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 200/5A.1 Set of phase indicating lamp with MCB BUSBAR 100A TPN Bus bar of aluminimum alloy. OUTGOING 3 nos. 32A 415V, TP+N MCCB of 25KA with TM based release having O/L, S/C protection.

NS Design, Manufacturing, supplying, fixing in position, testing and commissioning of the following front operated front access 2mm thick CRCA steel enclosure free standing, water, dust and vermin proof outdoor type Feeder pillars-1 with IP-54 protection hinged and lockable doors complete with interconnections copper crimping lugs, brass glands bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system . The panels fault withstanding capacity shall be of 25 MVA at 415 volts. All live accessories part shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be of colure coded with Heat shrinkable PVC insulated sleeves.INCOMER :1 no. 63A 415 Volts, TP+N MCCB 25kA with Thermal magnetic trip unit and ON, OFF, TRIP Indicating lamps.1 Set of phase indicating lamp with MCB, 1 no. 63A 415 Volts, 4P Contactor with time switch.BUS BARS:80 A TPN bus bars of aluminium alloy.OUT GOING: 16 Nos. 16A DP MCB of 10kA.

NS Design, Manufacturing, supplying, fixing in position, testing and commissioning of the following front operated front access 2mm thick CRCA steel enclosure free standing, water, dust and vermin proof outdoor type Feeder pillars-2 with IP-54 protection hinged and lockable doors complete with interconnections copper crimping lugs, brass glands bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system . The panels fault withstanding capacity shall be of 25 MVA at 415 volts. All live accessories part shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be of colure coded with Heat shrinkable PVC insulated sleeves.INCOMER :1 no. 125A 415 Volts, TP+N MCCB 25kA with Thermal magnetic trip unit and ON, OFF, TRIP Indicating lamps.1 Set of phase indicating lamp with MCB. BUS BARS:150 A TPN bus bars of aluminium alloy.OUT GOING: 42 Nos. 16A DP MCB of 10kA.2 Nos. 32A 4P MCB of 10kA.

Makin Developers Pvt. Ltd.

SURI CONSTRUCTIONS

M/S Shiv Kumar Agarwal

M/s Mahalaxmi Construction

unipro techno infrastructure pvt ltd