Civil Works for Creation of Facilities for Fetal Medicine, Medical Record Room, Plastic Department, Kitchen, GI Shed, Oxygen Generation Plant Room, Disabled-Friendly Infrastructure and Telemedicine Room, Compound Wall at NCH Campus Surat.

Name of work :- Civil Works for Creation of Facilities for Fetal Medicine, Medical Record Room, Plastic Department, Kitchen, GI Shed, Oxygen

Generation Plant Room, Disabled-Friendly Infrastructure and Telemedicine Room, Compound Wall at NCH Campus Surat.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Excavation for foundation upto 1.50 mt depth including sorting out and stacking of

Rupees One Hundred Twenty Three and

1 400.00 useful materials and disposing the excavated stuff upto any lead (A) Loose or soft CMT 123.13

Paisa Twelve Only

Excavation for foundation 1.50 mt to 3.00 mt depth including sorting out and stacking

Rupees One Hundred Thirty Six and Paisa

2 150.00 of useful materials and disposing the excavated stuff upto any lead (A)Loose or soft CMT 136.47

Forty Seven Only

Filling available excavated Earth (Excluding Rock) in trench plinth side of foundation

Rupees One Hundred Thirty Six and Paisa

3 400.00 . in layer not excluding 20 cm in depth consolidation each deposited layer by ramming CMT 136.92

Ninety One Only

and watering etc. complete

Filling foundation and plinth with murrum or selected soil in layer of 20 cm in Rupees Three Hundred One and Paisa

4 250.00 CMT 301.78 Seventy Seven Only

thickness including ramming watering and consolidating etc. complete

Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and getting out the soil

Rupees One Thousand Five Hundred Sixty

5 50.00 and disposal of the surplus excavated soil as directed within a lead of 50 Meter for Each 1561.19

One and Paisa Eighteen Only

following diameter of pipes.(iii) 300 mm

Providing and laying cement concrete 1:2:4 (1- Cement: 2- Coarse sand : 4- graded

Rupees Three Thousand Seven Hundred

6 15.00 stone aggregates 20 mm nominal size) and curing complete including cost of CMT 3741.69

Forty One and Paisa Sixty Eight Only

formwork in (A) Foundation and Plinth

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and laying in position Ready Mixed M-25 grade concrete for reinforced

cement conctere work , using cement content as per approved Design Mix

manufactured in fully automatic batching plant and transported to site of work in

transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured

as per mix design of specified grade for reinforced cement concrete work including

pumping of R.M.C. from transit mixer to site of laying, including the cost of form Rupees Five Thousand Five Hundred Fifty

7 135.00 work but excluding the cost of reinforcement for reinforced concrete including cost of CMT 5557.02 Seven and Paisa Two Only

admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength and durability as per

direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per

Letest Gov GR ) For Footing, Column, Beam, Sleb, Lintel, Chajja Foundation to 10th

Providing TMT Bar FE 500D reinforcement virgin steel for R.C.C. work including

8 10000.00 KG 83.06 Rupees Eighty Three and Paisa Six Only

bending, binding and placing in position complete up to All floor Level

Masonary work using Sand based Aerated light weight concrete block having

crushing strength not less than 35 kg/sqcm for super structure above plinth level in Rupees Five Thousand Two Hundred Sixty

cement mortar 1:5 ( 1 cement : 5 fine sand ) complete as per Technical Specification Nine and Paisa Fifty One Only

Providing 15 mm thick mala cement plaster on interior brick / concrete work for

plastering comprising of base coat of 11 mm thick cement plaster in cement mortar (1

Cement : 4 coarse sand) in rough finishing and 4 mm thick top coat of cement mortar Rupees Three Hundred Fourteen and

10 500.00 1:2 (1 Cement : 2 Coarse sand) finished with trovel including scaffolding curing with SMT 314.16 Paisa Sixteen Only

1x1mm Grooves at junction of Structural members etc. complete. up to 11th floor

Providing 10 mm. Thick cement plaster in single coat for plastering on ceiling and

soffits of stairs and finished even and smooth in : (I) Cement mortar 1:4 (1 cement : Rupees One Hundred Eighty Three and

4 sand) with 1x1mm Grooves at junction of Structural members etc. complete. up to Paisa Seventy Five Only

11th floor level

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

20 mm Thick sand faced / Mala cement plaster on walls for up to 11th floor level

above ground level consisting of 12 mm Thick backing coat of c.m. 1:3 (1 cement : 3 Rupees Three Hundred Forty Seven and

sand) and 8 mm Thick finishing coat of c.m. 1:1 (1 cement : 1 sand) etc. complete.up Paisa Forty One Only

to 11th floor level

Applying two coats of (white cement based) or (acrylic lappy (putty)) and two coats

of primer of approved brand and manufacture on new wall surface to give an even

13 700.00 SMT 40.59 Rupees Forty and Paisa Fifty Nine Only

shade including thoroughly brushing the surface free from mortar dropping and other

foreign matter and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of approved brand and

manufacture on undecorated wall surface, ceiling surface and sloping roofs to give an

14 1500.00 SMT 89.04 Rupees Eighty Nine and Paisa Four Only

even shade including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Providing And filling with good quality sinder(steam coal) as directed by engineer in

Rupees Four Hundred Fifty and Paisa

15 15.00 charge in sunks in layers of 15 cm thick,including watering,placing ,ramming well etc CMT 450.46

as directed, up to 11th floor level.

Providing & fixing in position standard extruded Aluminum Two track sliding

shutters with colour anodized section having Frame Top & Bottom member size

61.85mm x 31.75mm x1.20mm size Weight per Rmt= 0.695 Kg and Frame vertical

membesr size 61.85mm x 31.75mm x 1.30mm size Weight per Rmt = 0.659 Kg For

shutters using top and bottom size 50 x 20 x 1.50 mm size Weight per Rmt =

Kg & interlock member size 50 x 29 x 1.50 mm size Weight per Rmt = 0.994Kg &

side member size 50 x 20 x 1.50 mm size Weight per Rmt = 0.731 Kg Two track

sliding glass shutters including providing 6 mm thick Sceint gobain heat 70% Rupees Five Thousand Thirty and Paisa

16 14.40 SMT 5030.81 Eighty One Only

reflactive glass for glazing fixed with Rubber gasket,Air Lock Strip Silicon Sealant

with Standard Extruded Colour Anodized Aluminum Coted fittings including

Stainless steel mosqito net jali ,wire of I.S gauge designation 85-G with wire of

mm fix in aluminium door, window, ventilator shutters of any size, any shape with

etc all complete for all required materials labours and equipments as per detail

drawing window. as directed. For Windows

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing & Fixing in position standard extruded approved colour anodised

Aluminum Ventilator with outer frame 65 x 25 mm Stander Frame with 6 mm thick

Sceint gobain heat 70% reflactive glass Fix glass Louver alluminium strip blade

Rupees Three Thousand Eight Hundred

17 10.80 fixed or lovers ventilation including for glazing fixed with Transparent Silicon gasket SMT 3820.83

Twenty and Paisa Eighty Three Only

with Standard Extruded Colour Anodized Aluminum Coted fittings and all required

materials labours and equipments as per detail drawing Ventilator. as directed. For V1

Providing and fixing factory made single extruded WPC (Wood Polymer Composite)

solid plain flush door shutter 30MM THICK of required size comprising of virgin

polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers

(wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity

index of 12 for 100 gms) having minimum density of 650 kg/cum and screw

withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive Rupees Four Thousand Two Hundred

18 10.08 strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of SMT 4240.99 Forty and Paisa Ninety Nine Only

flame of Class A category with property of being termite/borer proof, water/moisture

proof and fire retardant and fixing with stainless steel butt hinges of required size with

necessary full body threaded star headed counter sunk S.S screws, all as per direction

of Engineer-In-Charge.WPC

Providing and laying machine cut machine polished Granite stone Sill, Jam, treads

and risers rounded moulding laid over 12 mm (avg.) thick bases of cement mortar 1:6 Rupees One Thousand Seven Hundred

(1-cement : 6-coarse sand) jointed with grey or colour cement slurry including Twenty Nine and Paisa Twelve Only

rubbing and polishing incl. etc. complete

P & L 60x60 cm. Matt vitrified Tiles flooring 8 & 10mm Thick Tiles flooring over

20 mm (average) base, skrting risers of steps, Dedo of cement mortar 1:6 ( 1 cement:

Rupees One Thousand Five Hundred

20 61.25 6 coarse sand) on new surface or fixing on existing flooring by adhesive material SMT 1589.74

Eighty Nine and Paisa Seventy Four Only

including finised with flush pointing & cleaning the surface etc. complete and Colour

Shade approved byEngineer-In-Charge (item including existing flooring dismentaling)

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm

broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to

be tempered to bring mortar creme out upto surface using white cement including

rounding off junctions and extending them upto 15 cm along the wall,clearing with

water and oxalic acid etc. as directed. + Providing and laying broken chine mosaic

flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid SMT Rupees One Thousand One Hundred Fifty

21 50.00 1153.84 Three and Paisa Eighty Four Only

over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out

upto surface using white cement including rounding off junctions and extending them

upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.(item

include dismentaling of existing Water Proffing)

Providinfg and fixing Safty grills of required pattern for windows/ Door using

necessary M.S angle/ M.S pipe, M.S flats and other structural steel at required

Rupees One Hundred Fifteen and Paisa

22 800.00 spacing including cutting, welding and fabriction etc. including one coat of primer of Kg 115.14

approved quality and two coats of oil painting as per detail drawing etc complete.

Providing erecting and fixing double coated (ISI) water tank of required capacity

23 2000.00 each with all necessary fittings and connection etc. complete on terrace. Litre 3.95 Rupees Three and Paisa Ninety Four Only

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH-

40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of Special type on Clamping system made out From Z

Clamps with nut/bolt wall Clips etc. at every two metre C/C or shall be concelled as Rupees One Hundred Ninety Five and

24 100.00 Rmt 195.67 Paisa Sixty Six Only

directed including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH-

40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of Special type on Clamping system made out From Z

Rupees One Hundred Forty Eight and

25 100.00 Clamps with nut/bolt wall Clips etc. at every two metre C/C or shall be concelled as Rmt 148.12

Paisa Eleven Only

directed including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH-

40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of Special type on Clamping system made out From Z

Rupees Ninety One and Paisa Eighty

26 200.00 Clamps with nut/bolt wall Clips etc. at every two metre C/C or shall be concelled as Rmt 91.84

directed including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH-

40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of Special type on Clamping system made out From Z

Rupees Seventy Two and Paisa Sixty Four

27 150.00 Clamps with nut/bolt wall Clips etc. at every two metre C/C or shall be concelled as Rmt 72.65

directed including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B)

conforming to IS 13592-1992 with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be

fixed on wall using of Special type on Clamping system made out From Z Clamps Rupees Eight Hundred Thirty Four and

28 15.00 with nut/bolt wall Clips etc. of the size 160 mm diametre x 210 mm length x 196 mm Rmt 834.38 Paisa Thirty Eight Only

heigh at every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure

poluthene pipes of the following outside Dia. Low densidy, complete with special Rupees Three Hundred Thirty Nine and

falnge compression type fittings, wall clipsetc. including making good the wall ceiling Paisa Four Only

and floor.(G)110 mm

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-

pressure pipes I.S. class NP2 of the following internal diameter with collars and butt Rupees Two Hundred Fifty Seven and

ends prepared for collar joints including testing of joints complete.(B) 150mm Paisa Eighteen Only

Providing and fixing in C.I. SWR cowel went 110mm dia to pipes.(B) 110mm dia. Rupees Three Hundred Forty Four and

31 10.00 No 344.09 Paisa Eight Only

Providing and fixing cast iron (Spun) Nahni trap of the following nominal diameter

of self cleaning design with C.I. screaed down or higned grating including cost of Rupees Six Hundred Fifty Three and Paisa

cutting and making good the walls and floor 100mm inlet and 50mm outlet.(C) Eight Only

Providing and fixing wash down water closet dual flushing system type (European

type W C pan) with integral P and S trap including jointing the trap with soil pipe in

cement mortar 1:1 (1 cement five sand) including providing and fixing plastic seat

cover for wash down WC with CP brass hinges and rubber buffers back plastic seat

and including fitting such as lead valve siphon 15 mm dia brass ball valve with Rupees Four Thousand Two Hundred

33 4.00 No 4242.00 Forty Two and Zero Paisa Only

polythene float CP brass handle unions and couplings for connection with inlet out let

and over flow pipes 40 mm dia porcelain enameled flush bend including cutting holes

in walls and making good the same connection the flush bend with cistern and closet

vitreous china.

Providing and fixing brass screw down stop tap.(A) 25mm dia. Rupees Two Hundred Twenty and Paisa

34 10.00 No 220.82 Eighty One Only

Providing and fixing brass screw down stop tap.(A) 15mm dia. Rupees Two Hundred Five and Paisa

35 10.00 No 205.83 Eighty Two Only

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (ii) Rupees One Hundred Eighty Nine and

36 5.00 No 189.84 Paisa Eighty Three Only

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S.

brackets painted white including sutting holes and making good the same but Rupees One Thousand Five Hundred

excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm Thirty Three and Paisa Thirty Two Only

size. (i) In white colour.

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mm dia. Rupees Sixty Seven and Paisa Ninety One

Providing and fixing Urinal of approved quality including conecting the Urinal with

waste pipe , tap etc. complete.(A) White earthenware flat back or corner Rupees One Thousand Seventy Four and

type size 430mm x 260mm x 350mm. Paisa Eighty Six Only

Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm dia. Rupees Seventy Eight and Paisa Seventy

40 5.00 No 78.75 Four Only

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass

Rupees Eight Hundred Fifty Nine and

41 4.00 mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with No 859.41

Paisa Forty Only

C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to Rupees Six Hundred Sixteen and Paisa

42 4.00 No 616.42 Forty Two Only

wooden plugs with C.P. brass scews (B) 600mm x 20mm size.

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib Rupees One Hundred Eighty Six and Paisa

43 20.00 No 186.83 Eighty Two Only

tap polished bright. (i) 15mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, Rupees Three Hundred Eight and Paisa

44 5.00 No 308.73 Seventy Two Only

shanks and back nuts. (i) 15mm dia.

Providing and fixing in position English/Gujrati letters made from 3.0 mm thick ACP

Rupees Four Thousand Five Hundred

45 15.00 sheet Signage as directed by Engineer in charge with all necessary tools & plants etc. Smt 4545.00

Forty Five and Zero Paisa Only

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and

Rupees One Thousand Two Hundred Forty

46 5.00 water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard No 1246.92

Six and Paisa Ninety One Only

weight (i) Square mouth traps (B) 150mm x 100mm size P or R type

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Constructing brick masonry chamber for underground C.I. Inspection chamber and

bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame

15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone Rupees Three Thousand Nine Hundred

47 15.00 aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with No 3916.78 Sixteen and Paisa Seventy Eight Only

cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(i) Inside dimensions 500mmx 700mm and 450mm deep

for single pipe line.

Constructing Sandwitch Platform of 18 mm thick Polished Black Granite at top and

25 mm thick Kota stone slab one side polished at bottom with cementing Materials /

adhsives including makeing necessary grooves in walls with Vertical sandwich two

Kotastone 25 mm support every 60 cm centre to centre or as required including all Rupees Two Thousand Seven Hundred

48 20.00 labour material of approved quality incl. full moulded round front edge granite strip SMT 2772.45 Seventy Two and Paisa Forty Five Only

of one side polished and jointed with grey cement slurry including rubbing and

polishing etc. complete up to 11th floor levels (only top Measured)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS :

13983 with C.I. brackets and stainless steel plug 40 mm, including painting of

fittings and brackets, cutting and making good the walls wherever required, painted Rupees Two Thousand Three Hundred

49 4.00 white including cutting holes in walls and making good the same but excluding No 2326.66 Twenty Six and Paisa Sixty Five Only

fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and fixing alluminum colour anodised Partition with door / Double or

single door of sides, top and bottom member of size 101.6 mm X 44.45 mm X

mm ( 1.605 Kg / Rmt ) with vertical sides member and central vertical member of size

101.6mm X 44.45mm X 2.01mm ( 1.605 Kg / Rmt ) and glazing clip (0.124 Kg / Rmt Rupees Two Thousand Five Hundred

50 254.80 ) with 6mm thick glass in upper portion and 8 mm thick high press laminated sheet in SMT 2525.00 Twenty Five and Zero Paisa Only

lower portion as per detailed drawing in true line and level including fixtures,gaskets,

clips etc complete. All Floor.including all type of fixtures, hardware, pivot,simple

lock,handle and required all other materials and tools.directed by EIC

Proving & Fixing Chicken mesh for joint between brick work & RCC work fixing Rupees Two Hundred Seventy and Paisa

51 40.00 Smt 270.18 Seventeen Only

with nail & GI washer as per director in Charge

Providing and laying polished kota stone slab 20 to 25mm thick in risers of

steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement :

coarse sand) and jointed with gray cement slury mixed with pigment to match the

Rupees One Thousand Three Hundred

52 70.00 shade of slab including rubbing and polishing etc. jointed 3 MM EPOXY GROOVE Smt 1344.31

Forty Four and Paisa Thirty One Only

with color cement slurry including finised with flush pointing & cleaning the surface

etc. complete and Colour Shade approved by Engineer-In-Charge

Providing 20 mm thick water proof cement plaster using water proofing powder

1Kg/1bag of cement up to 11th floor levels on brick / concrete wall work using water

proofing materials in C M 1: 4 ( 1 cement 4 coasrse sand) including finishing with a

flooting coat of neat cement slurry etc complete up to 11th floor level. and shall be Rupees Two Hundred Seventy Six and

53 50.00 guaranteed for minimum period of 10 years after handing over the completed building SMT 276.74 Paisa Seventy Four Only

by the main contractor to be finished as directed. Stamp paper guarantee 10 years to

be furnished before receiving any payment from the client.

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block

60mm thick with grade of concrete M300 pnumatic compressed / vibrated

Rupees Six Hundred Eighty Three and

54 100.00 mechanically and as per approved design Confirming to IS 15658 : 2006 including 35 SMT 683.88

Paisa Eighty Eight Only

mm Sand layer for levelling and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and laying Rubber tectile flooring (Direction and warning tile -

300x300x2.3 mm), Luminance Contrast: Yellow: 47.85, Fixing with: Self-adhesive Rupees One Thousand Five Hundred

tape Butyl rubber tape Epoxy Adhesive for desable person anti skit as per requirment Fifteen and Zero Paisa Only

and instructed by engineer incharge

Providing and fixing bright finish brass hydraulic door closer of approved model and Rupees One Thousand Four Hundred

56 8.00 make with necessary screws and finishing etc. complete. Each 1422.84 Twenty Two and Paisa Eighty Three Only

Providing and fixing 19 mm thick water proof plywood shutters for platform cabinet

including using approved formica on shutter and teakwood decorative batten patti in Rupees Four Thousand One Hundred Sixty

front portion with necessray fixtures and fastenings including polishing work etc. Five and Paisa Twenty Four Only

complete and direction of engineer in charge.

Fabricating, supplying and fixing in position SS railing for staircase and balcony with

brush finish and 304 grade as per Indian Standrd and detailed drawing including

Rupees Three Thousand One Hundred

58 20.00 grinding, cleaning and filling the welded spots with SS finish (Only Length will be RMT 3173.42

Seventy Three and Paisa Forty Two Only

paid for payment heigth max.1.0 mt.). The Work to be executed as per consultant

Providing and fixing in position collapsible steel shutters with vertical channels 20 x

10 x 2 mm braced with flat iron diagonals 20 x 5 mm size with top & bottom rails of

Rupees Five Thousand Eight Hundred

59 7.50 T iron 40 x 40 x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking SMT 5825.33

Twenty Five and Paisa Thirty Two Only

arrangements, stoppers handles including applying a priming coat with red lead paint

& Two Coat of oil paint etc. complete

Providing corrugated G.I. sheet of class-3 roofing fixed with glavanished iron J or L

Hooks, Bolts and nuts 8mm diameter with bitumen and G.I. limpet washer or G.I. Rupees Seven Hundred Twenty Seven and

limpet washer. filled with white lead complete excluding the cost of purlins, Rafters Paisa Twelve Only

and Trusses.(1) 0.80 mm thick sheet.

Painting two coats (excluding priming coat) on steel and other metal surface with

enamel paint, brushing, interior to give an even shade including cleaning the surface Rupees Eighty Seven and Paisa Eighty

an even shade including cleanicn the surface of all dirt, dust and other foreign matter. Only

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing, supplying, fabricating and erecting in position the steel Work for colums,

grill, bars, truss, purlins, runners, cleats, insert plate, base plate etc for all structural

elements as per detail, made up from closed structural steel hollow sections

(RHS/SHS including rolled section ) as per IS 4923 of grade Yst 310 mpa - weather

resistant of Tata Structural / sections or an approved equivalent as per details /

drawings/instructions including cutting, bending, jointing, connecting, welding and / Rupees Seventy Five and Paisa Seventy

62 8500.00 Kg. 75.75 Five Only

bolting and / riveting and fabricating and erecting in position etc complete for all

levels as directed. The rate to include all necessary fixtures, fastening including

welding rods of standard approvded quality etc for complete the job. The rate shall

also include the one coat of red lead paint, epoxy coat & necessary scaffolding etc.

complete as directed

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra

Strength The Light weight calcium silicate ceiling tiles shall have , light reflection

85% noncombustible as per B.S. 476 part IV, 100% humidity resistanceandalsohaving

thermalconductivity0.043° w/m KC.for the best thermal Insulation . The Light weight

calcium Silicate tile shall be of approved texture Fine fissured/ Spintone/Cosmos

having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of

size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal

gridof hot dipped galvanized steel sections (galvanizing @120 grams per sqm SMT Rupees One Thousand Six Hundred Forty

63 160.00 1648.96 Eight and Paisa Ninety Five Only

including both side) consisting of main ‘T’ runner suitably spaced at joints to get

required length and size of 24X38mm made from 0.30 mm thick (minimum) sheet,

1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to

centre to form agrid of 1200X600mm and secondary cross ’T’ of length 600mm and

size 24x28mm made of 0.30 mm thick (Minimum) sheet to be interlocked at middle

of the 1200X600mm panel to form grid of size

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and fixng curtain For Door/Window using Fire retardent Material including

necessary hanging attachments like hooks/ rings, 25mm SS rod/ alluminium channel/

Rupees One Thousand Seven Hundred

64 10.00 Socket on rod ends/ middle supporting sockets including 1 inch Adjustable Curtain Rmt 1717.00

Seventeen and Zero Paisa Only

S.S. Rod up to 12 ft long and parda 7 ft Ht with best quality Curtain Knobs and

bracket etc. complete

Providing & fixing of reinforcement bars (reiforcement bars shall be paid extra under

relevant item of work)Providing and supplying HY200 with Rebar or HIT-V

Threaded Rod with a pre-defined ratio (3:1) of resin and hardener in a soft foil pack

of 330ml, 500ml. The product should be approved by ETA, ICC, CSTB, COLA, BZS

with Shock approval, Seismic approval in Anchors and Rebars to use in cracked/un-

cracked concrete, tested for service temperature of -10deg C to +60 deg C.

Application to be designed separately for Rebares as Simply Supported Moment or

Splice as per EC2/TR23 or relevant tested and accepted rebar guidelines. Anchoring Rupees Three Hundred Seventeen and

65 16.00 with HIT-V with HY200 to be designed as per ETAG guidelines of post installation Each 317.14 Paisa Fourteen Only

of anchors and TR 29. LEED certified injection adhesive for rebar fixing in wet/dry

flooded holes conditions for diameters. The chemical should have service life of more

than 50 years and is to be tested for water tightness. Providing, Drilling & Fixing Re -

Bars As per Engineer Instruction Excluding cost of steel & including Chemical.

8 mm dia (12 mm drill diameter and 200 mm depth)

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing & fixing of reinforcement bars (reiforcement bars shall be paid extra under

relevant item of work)Providing and supplying HY200 with Rebar or HIT-V

Threaded Rod with a pre-defined ratio (3:1) of resin and hardener in a soft foil pack

of 330ml, 500ml. The product should be approved by ETA, ICC, CSTB, COLA, BZS

with Shock approval, Seismic approval in Anchors and Rebars to use in cracked/un-

cracked concrete, tested for service temperature of -10deg C to +60 deg C.

Application to be designed separately for Rebares as Simply Supported Moment or

Splice as per EC2/TR23 or relevant tested and accepted rebar guidelines. Anchoring Rupees Three Hundred Seventy Eight and

66 16.00 with HIT-V with HY200 to be designed as per ETAG guidelines of post installation Each 378.75 Paisa Seventy Five Only

of anchors and TR 29. LEED certified injection adhesive for rebar fixing in wet/dry

flooded holes conditions for diameters. The chemical should have service life of more

than 50 years and is to be tested for water tightness. Providing, Drilling & Fixing Re -

Bars As per Engineer Instruction Excluding cost of steel & including Chemical.

10 mm dia (14 mm drill diameter and 200 mm depth)

Providing and fixing rubber speed breaker including installation as directed by Rupees One Thousand Three Hundred

67 16.00 RMT 1393.80 Ninety Three and Paisa Eighty Only

Engineer incharge.

Providing and fixing in position S.S. daso by providing top 50 mm dia stain less steel

pipe rail with starting and end point vertical post of 50 mm dia with wall/column

Rupees One Thousand Seven Hundred

68 15.00 including bending welding and fixing for staircase and balcony as directed.(testing is RMT 1794.77

Ninety Four and Paisa Seventy Seven Only

required of s.s 304). The work to be executed as per Architect drawing and E.I.C. etc.

complete up to 11th floor levels.

Providing and Fixing Commander make grab bar made up of aluminium alloy for

Divyang toilet with EWC P or S concealed (710 X 370 X 810 mm),Cistern,cruse

special soft close seat cover,internal fittungs,wash basin 510 X 400 mm, Spatula lever Rupees Thirty Seven Thousand Eight

69 6.00 faucet,2 nos.Wall mounted grab bar 600 mm long , wall mounted hinged hand rail Nos. 37875.00 Hundred Seventy Five and Zero Paisa

750 X 100 mm with bottel trap and paper holder with all require s.s fixture &

fastening which approved by Engineer incharge.

Demolition including stacking of serviceable materilas and disposal of unserviceable Rupees One Thousand Thirty and Paisa

70 20.00 CMT 1030.81 Eighty Only

materials with all lead and lift. (i) R.C.C. work

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Demolition of Brick work and stone masonry including stacking of serviceable

Rupees Five Hundred Thirty Six and Paisa

71 15.00 materilas and disposal of unserviceable materials with all lead and lift.(ii) In Cement CMT 536.09

Dismentling steel work including distempering and stacking the materials with all

72 105.00 Kg. 3.67 Rupees Three and Paisa Sixty Six Only

Dismentling doors, windows, ventilators etc. (wood or steel) shutters including

Rupees Two Hundred Forty Four and

73 15.00 chowkhats architraves, holdfasts and other attachment etc. complete and stacking Each 244.98

Paisa Ninety Seven Only

them within all lead and lift.(ii) Exceeding 3 Sq.M. in area.

Dismentling C.I. pipes G.S.W.pipes abd A.C. rain water pipes with fittings and Rupees Seventy Three and Paisa Two

clamps including stacking the materials with all lead and lift ( for any dia, of pipe

Dismantling santtary fittings like wash basin . W.C. pan Indian and European type, Rupees Three Hundred Ninety Four and

75 15.00 Each 394.51 Paisa Fifty Only

flushing tank etc. including stacking the materials with all lead and lift.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

All the waterproofing activities shall be carried out by in-house application company

of the principal material manufacturer and provide a written corporate Supply Apply

Corporate Warranty from the principal manufacturer that all work executed will be

free from defects in materials, workmanship and free of leaks for a period of 3 years

from the date of Work Completion, unless resulting from structural defects or causes

other than the work of this section. Said defects shall be remedied by the principal

manufacturer for the period of the warranty without additional cost to the owner for

waterproofing material only. Providing and applying hydrophilic crystalline

based waterproofing system In two coat application.The application to be done

from+ve(positive) side on a wet open pore green concrete surface at Rupees Three Hundred Fifty Four and

76 30.00 coverage of 0.8to1kg/sqm as per manufacturer specification.It should be SMT 354.51 Paisa Fifty One Only

hydrophilic in nature,should be able to grow crystals year after year to seal

microcracks.The product should confirm to DIN1048 part5 nd should

provide in depth crystallization.The material and application warranty to be given by

manufacturer’s authorized distributor/applicator on prescribed format for10

years.Note:- Treated area should be screeded using hydrophilic crystalline admixture

KIM(Krstol Internal Membrane) @ 2% for be stresults:-Application of crystalline

coating to be done within 7days of casting of concrete

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

(Acoustic Wall Paneling (upper edge reach- above 2.44 mts to ceiling) Providing

and fixing acoustical wall paneling with using ultra metal frame work to be fixed on

wall at every 600mm horizontally and 1200 mm vertically fixed with the help of

Metal cleat by using IC-91 which is screw fixed directly to the wall and fixing CS

on IC91 with help of clip/Screw and where ever required and using Knauf make

insulation glass wool between framing and panel with technical specification of

48 Kg/m3 and 50MM thick on above CS55 fixing SONIDO acoustic board of

size 1200 x 600 x 15mm fix on CS55 and then fixing 6MM thick ply wood of size

50MM than fixing vinyl grippers of ecotone make EG 15 Griper system using

,Tracks ( Perimeter Track , Half wrap, mid seam whatever is required) . Vinyl SMT Rupees Three Thousand Nine Hundred

77 38.00 3949.10 Forty Nine and Paisa Ten Only

grippers must have base tapes for better grip. Fixed in between Vinyl grippers and

sonido board pasting ecotone synco PF of 10X10mm thick on the acoustical panel

by using adhesive as per specifications of manufacturer. Fabric Stretching

Supplying and laying FR grade fabric stretch Clara Fabric shade vide catalogue Name

Brass/Atom is then cut into required size and shape and stretched, inserted

inside the gripper by using tools recommended by manufacturer, by Architect

and as specified including all accessories, material & labour complete as directed

by Architect / Engineer – in – charge

Providing & Fixing health faucet with 8 mm dia 1 mtr long flexible tube and wall Rupees One Thousand Four Hundred Five

78 10.00 Nos. 1405.92 and Paisa Ninety Two Only

hook as per eic instruction.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and Supplying Glass door storwel . and should be mandatorily submitted

along with Bid. glass door storwel should be mandatorily submitted along with Bid

shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded

construction. It should have shelf thickness of 0.7 mm, Back thickness of 0.8mm,

Door thickness of 0.8mm (high yield strength) and all other components shall have a

thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield

strength as per IS:513. The glass door storwel shall have a brass handle and a 2 way

locking mechanism with shooting bolt . It should have a height wise adjustable shelf Rupees Eight Thousand One Hundred

79 1.00 Nos. 8144.64 Forty Four and Paisa Sixty Four Only

mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It

should also have a M10 Screw type Leveller with Hex plastic base. The finishing

shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of

colour options and shelving options shall be available.The rate shall include all

materials, hardware, and labour etc. complete as per instruction of engineer-in charge.

Providing and Supplying side table with Overall Size :Depth — 461.0 mm Width —

460.0 mm Height — 510.0 mm Material:Body panels of Bed side table are made of

18 mm thick Prelaminated Particle Board 1S:12823 Class E1 (as per EN13986) .All

the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with

Hot Melt EVA glue.Drawer front are made of 18 mm thick Prelaminated Particle

board 1S:12823 Class E1 (as per EN13986). Hardware:The high quality hardware Rupees Four Thousand Forty and Zero

80 1.00 used like Roller slides, Hinges , minifix, dowels is of make Nos. 4040.00 Paisa Only

Hettich.Construction:Knock Down construction.Packets :1 packet.Finish :.18 mm

thick PrelaminatedParticle Board 1S:12823 Class E1 (as per EN13986) is in Imperial

Oak shade.Lipping shade is 299P MAKE REHAU.The rate shall include all

materials, hardware, and labour etc. complete as per instruction of engineer-in charge.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and Supplying main table with ERU ..Supplying and placing in position

Main Table with ERU of the following specifications. Its size shall be 1650 Width x

700 Depth x 743 Height (Main Desk) 1000 Width X 450Depth X 743 Height

(ERU).Top shall be of 18 mm thickness made of PLT board with 2 mm Edge

banding. Wenge and savannah Maple PLT board shall be used. The Understructure

shall be in pre-laminated panels made with PLT boards . 2- Drawerand 3 - Drawer Rupees Nineteen Thousand Four Hundred

81 1.00 Nos. 19462.70 Sixty Two and Paisa Seventy Only

storage units with different combinations to support tops made with 18 mm PLT

boards of different colours.Modesty and back panels made with 18 mm PLT boards.

The pedestals / storages shall be fitted with necessary locks. The rate shall include all

materials, hardware, and labour etc. complete as per instruction of engineer-in charge.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and Supplying Leatherette chair with High Back Chair. SEAT/BACK ASSEMBLY : The

Cushioned seat should be made of Injection molded Plastic outer and inner. Plastic Inner should be

upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2

kg/m3,and hardness load 16 ± 2 kgf for 25 Percent compression.The Cushioned back should be made

of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It

upholstered with Pure Leather.Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D)BACK SIZE : 47.5 cm. (W) x

77 cm. (D)ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in

pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03

cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up

to 6.5±0.5cm in 5 steps.ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism

should be designed with the following features:• 360° revolving type.• Front-pivot for tilt with feet

resting on ground and continuous lumbar support ensuring more comfort.• Tilt tension adjustment can

be operated in seating position.• 5-position Tilt limiter giving option of variable tilt angle to the chair.•

Seat/back tilting ratio of 1: 2• The mechanism housing should be made up of HPDC Aluminium black

powder coated.SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat Rupees Twenty Thousand Seven Hundred

82 1.00 through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.ADJUSTABLE Nos. 20705.00 Five and Zero Paisa Only

BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T

spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit

individual need.PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an

adjustment stroke of 10.0±0.3 cm.PEDESTAL ASSEMBLY The pedestal should be High Pressure

Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ±

0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS:The twin wheel

castors should be injection moulded in Black Polypropylene. Overall Dimensions of Chair-Seat

Height -44.5 to 54.5 cm.Height -114.0-131.5 cm.Width and Depth of Chair as measured from base -

Width-76.1 cm and Depth-76.1 cmThe rate shall include all materials, hardware, and labour etc.

complete as per instruction of engineer-in charge.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and Placing Partitions are generally structured by Aluminum extruded sections.All panels

are in standard size and ready to assemble condition.All exterior metal surfaces are POWDER

COATED FINISH .12 mm thk. Pre laminated or laminated panel on both the side of the partition. It

has provision for all utility management and to mount worktops, etc., All joineries are free from

Nailing, Screwing and adhesives. .All components are removable without any damage and designed to

reconstruct, reorient or reconfiguration layout very easily.Entire systems are free from maintenance

like refinishing anti pest treatments or refitting, lifetime.It has inherent Sound and thermal insulation

properties. All panels are twin layered and very proper sealing in joint are provided to ensure these

properties. System is designed in such a manner that resizing of structure and related mountings can be

carried out at site easily, if required. It is Eco‐Friendly in true sense. Partition Skeleton Main Vertical

Section : Aluminum extruded section having overall size of 73 mm x 29 mm having wall thk.

mm with provision to connect to outer vertical closing section at all side. Main Horizontal section :

Aluminum extruded section having overall size 73 mm x 29 mm having wall thk. 1.50 mm with

provision to connect with each other at side to supporting panels of 12 mm thk. on the both sides of

Rupees Three Thousand Five Hundred

83 150.00 partition. Electric trench box section : Aluminum extruded section having over all size 60 mm x 80 Nos. 3585.50 Eighty Five and Paisa Fifty Only

mm having wall thk. 1.40 mm with snap fitting arrangment. Connecting pole section : Aluminum

extruded section having overall size 99.60 x 99.60 box section having wall thk. 1.40 mm and

provision to connect with all type of connections. ( i.e. " L " , " T " and " PLUS connectivity ).

Verticle and Horizontal covring seal section : Aluminum extruded section having over all size

x 8.40 mm having wall thk. 1.20 and provision to cover all open sides with snap fitting. Double Glass

Section : Aluminum extruded section having over all size 56.0 mm x 9.70 mm having wall thk.

mm and provision to hold 5 mm thk. Glass with cushioned rubber for every side of glass on both the

sides of the panel. Solid filler panels: Solid panel made out of 12.00 mm thk. laminated / pre

laminated board of particle or MDF or PLY on both side of the partition. Glass filler panels : having

mm thk. Clear toughened Glass on both sides of the partition.

Memorandum showing items of works to be carried out

Approved Rate SOR 2024-25

Item estimated but

Item Of Work Unit In figures estimated

No. may be more In Words

Rs. Ps. quantites

Providing and Supplying Leatherette chair office chair.SEAT/BACK

ASSEMBLY: The seat and back should be made from seasoned wood and plywood.

The same should be upholstered with black synthetic leather and polyurethane

foam.BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm.

(D).ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x

±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60

microns).UNDERSTRUCTURE ASSEMBLY: The understructure assembly should Rupees Four Thousand Eight Hundred

84 20.00 Nos. 4858.10 Fifty Eight and Paisa Ten Only

be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S.

E.R.W. tube and powder coated (DFT 40-60 microns).Overall Dimensions of Chair-

Seat Height - 48.0 cm.Height - 87.5cm.Width and Depth of Chair as measured from

base - Width-58.0 cm and Depth-56.5 cm.The rate shall include all materials,

hardware, and labour etc. complete as per instruction of engineer-in charge.

Total Amount :-

Total Amount :-

Rupees :-Seventy Six Lakh Twenty One Thousand Eighteen Only

(A) Total tendered amount

(B) Rebate on above tendered amount(if any) (% In figure) ________ (% in Words) ___________________________

(C ) Net tendered amount(A - B)

(D) Net Tendered Amount (In words): Rupees

Deputy Executive Engineeer Executive Engineeer

Project Implementation Unit Zone 7 Project Implementation Unit zone