PROVN OF 02 X GAZIBO SPORTS STORE ROOM AND SANITARY BLOCK NEAR PAOAT AT MIL STN GANDHINAGAR

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation of pole,laying of cables etc in soft/loose soil and getting out complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Soft/ disintergrated rock complete all as specified and directed.

M&L for Surface dressing n exc 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as directed. Note : Depth after punning shall be measured and paid.

Removing excvaated soil nexc 50m and depositing where directed at a level n exc 1.5 m above the stating point soil etc completed all as specified and as directed.

Spreading and levelling under floor layers not exceeding 25 cm thick and well ramming including watering as required complete all as specified and directed.

Spreading and levelling under floor layers not exceeding 25 cm thick and well ramming including watering as required complete all as specified and directed.

Removing excavated material rocks exc 250m but n exc 500m and depositing where directed at a level n exc 1.5 m above the starting point in soil complete all as specified and directed.

M&L for hard core of gauge exc 63mm but n exc 100mm deposited, spread and levelled in layers n exc 15cm thick watered and rolled/rammed to a true surface completed all as specified and directed.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation, sub base, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (40mm graded aggregate) in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in surface channel and drains, etc. complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for padestal/coping around poles, including necessary form work, finishing even and smooth without using extra cement, all as specified and directed.

M&L for providing precast cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in manhole covers including placing the cover in position and set in cement mortar 1:6 complete all as specified and directed. Note : Reinforcement shall be measured and paid seperately.

M&L design mix RCC M-25 grade concrete in foundation including raft,footing foundations beem ,plinth beams base for coloumn etc complete all as specified and directed.

M&L design mix RCC M-25 (using 20 mm graded granite stone aggregate) for slabs suspended on walls, beams and columns, in floors, roofs, landings and in shelves and the like complete all as specified and directed.

M&L design mix RCC M-25 in lintel beams/lintels, roof beams over 1.50 mtr spancomplete all as specified and directed.

Supply only Integral waterproofing compound complete all as specified and directed.

M&L for old size fly ash Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for cutting chases, pinning in, for brick walls, making good to facings for concealed water tubing etc. cutting exceeding 10cm but not exceeding 20cm girth complete all as specified and directed.

Supply and laying sub class burnt bricks as cable protection cover length of bricks230x115x75mm laid perpendicular to cable all as directed.

Form work to sides of concrete foundations footing bases of coloumn raft and raft beams sides and soffits of plinth beams and similar works vertical or to batter complete all as specified and directed.

M&L for formwork to chullah hoods, cha jjas, troughs and similar items in cluding edges complete all as specified and directed.

M&L for Form work for to side and soffits of floor or roof beams, beam haunchings, girders bressummers lintels, cantilevers, shelved including sup-ports, overhangs etc also splays between floors and beams etc. complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

S&F, stainless steel butt hinges, medium weight, of size 100 mm complete all as specified and directed.

S&F framed work such as grills, grating etc with ends of bars shoulderd or rivetted or forcged into spikes ,framed guard bars, barred iron doors congirming to FE 290 Gde E-165 complete all as specified.

S&F, Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending, hooking etc and binding with MS wire 0.9mm dia(annealed).

S&F, mild steel TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

S&F mild steel work in weather shed posts, main and cross beams, hip and jack rafters, purlins, including special shaped washer etc. complete using ERW or induction butt welded tubes, conforming to IS 1161-1979, Gde St-240 complete all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

M&L Aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.30mm (section No 20621), bottom size 92x31.75x1.30mm (section No-20620) and shutter top & bottom of size 40x18x1.29 mm (section No-20844) and sides (handle) of size 40x18x1.29mm (section No-20846) and lock side shutter frame of size 40x18x1.29 mm (Section No 20845) with rubber gasket, beading and locking arrangement and rollers etc including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 4mm thick glass (any shade) with necessary rubber beading gasket etc all as specified. Make:-Indal/ Jindal/ Hindalco.

M&L for non asbestos, fibre reinforced deisgner cement board ceiling, 4mm thick (610mm x 610mm) with hot-dip GI heavy duty suspended ceiling gird system T-2420 all as per manufacturers instructions. (Make : M/S Everest Industries Ltd or equivalent).

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc and including 20mm thick screed bed in CM 1:4 complete as specified and directed.

M&L for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 40mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L 75 mm thick cement concrete type D2, 1:4:8 (40mm graded aggregate) in sub-floors, sub-bases, floors and pavings etc complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D-2( 40 mm graded stone aggregate ) as in sub base of flooring complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 350x250x7mm / 450x350x7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. complete all as specified and directed.

M&L for rendering cement plaster 12mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:4) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement with water proofing compound @3% by wt of cement or as per manufacturers instructions (WPC shall be paid seperately) complete all as specified and directed.

M&L for two coats of Acrylic distempe over one coat of 1mm thick wall care putty ( Make : Birla/JK White) base on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement primer complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying two coat of white wash on ceilings complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

S&F, 4mm thick, black tinted glass panes fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq.m in each pane

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F, steel water tubes with rubber gasket at end of each pieces of pipe, light grade, galvanized, with all fittings of size 40mm dia laid in floors/trenches/fixed with poles for protection of cable complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

Supplying and laying of 20mm outer dia CPVC pipes SDR 13.5 fittings on walls/ceiling or laying in floors including connection to old GI Pipe (if requried) complete all as specified and directed.

S&F of 20 mm outer dia CPVC elbow (3/4x 1/2) with brass thread at one end for fixing of taps etc and other end plain complete all as specified

S&F of 20mm outer dia CPVC Tee with brass thread at one end for fixing of taps etc and other end plain complete all as specified

Supply, hoisting and fixing in position, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top) including dismantling of old PVC/AC water storage tank of 500 liter capacity complete all as specified and directed.

S&F 15mm dia Brass CP bib cock cast copper alloy fancy type with long shank capstain head serewed down high pressure pipe in repairs complete all as specified and directed.

Supply only pillar taps fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed 15 mm bore dia complete all as specified and directed.

S&F, vitreous china wash down water closet pan including S or P trap (pedestal pattern), white with seat cover (including fixing bolts but excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, Stop valves, 15mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as directed.

S&F, Gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe for 20 mm bore of pipe complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms) complete, all as specified and directed.

S&F, PVC connection of 15 mm bore and 450 mm long with brass checknut and union etc complete

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F, 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) nahani trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore.

M&L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed as specified.

Cutting into existing manhole150 dia for connection new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate, smooth finished and reforming benching as required all as directed.

S&F, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, stainless steel tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed.

S&F, PVC low level flushing cistern 10 Ltr capacity including all fitting such as flush pipe brackets complete all as specified and directed.

S&F, vitreous china wash basin, white, flat back of size 450mm x300mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F, Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

M&L for wiring with and including multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories & including with multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with provision sunken concealed terminal boxes complete all as specified and directed for the followings :-

(a) One light/fan /Exhaust point controlled by one switch

(b) One multi purpose socket 5 Amps, Independent board.

S&F, LED light fitting, 1 x 20 watt 220V, AC, decorative box type with driver , holder , including LED tube light complete set flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

S&F, lamp holder insulated body with back plate for battern fittings complete all as specified and directed.

S&F Switch piano, flush type 5 Amps One Way 230 volts complete all as specified.

S&F modular switch piano, flush type 6 Amps one way 230 volts complete all as specified.

S&F, modular frame plate 8 module, ISI marked complete all as specified and directed.

S&F, modular metal flush box 6 module ISI marked complete all as specified and directed.

S&F, socket outlet 2 in1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F, MCB single pole with neutral 240 volts 32Amps with thimble suitable for existing wires incl connecting, testing and commissioning complete all as specified and directed.

S&F, Distribution Board SPN 4 way, 240 volts, factory made powder coated, double door with neutral and earth link, suitable for fixing MCB,s complete including connecting all as specified and directed.

S&F, Distribution Board SPN 2 way, 240 volts, factory made powder coated,Single door with neutral, suitable for fixing MCB,s SPN complete including connecting.

S&F Ceiling rose 3 terminal size 50x65mm surface type 230 volts complete all as specified.

Supplying & laying, XLPE insulated, PVC inner sheathed, 6 Sqmm, 2 Core, armored with galvanized steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete all as specified and directed.

Supply and laying in repair of GI pipe 40mm dia light grade below road/fixed to along the poles/walls with necessary clamping, including encasing the cable into the pipe all as specified and directed.

M&L for ceiling rose, PVC/poly carbonate, isolated body three terminals complete all as sepcified and directed.

S&F MCB SP 6-32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

S&F, MCB’s SPN 32 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

Supply and fix of exhaust fan, 300 mm sweep, 1400 rpm, MS body heavy duty, AC single phase, 230 volts with, blades, and frame and louvers including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed. Make : Crompton/ Havells /Khaitan/ Almonard/ Bajaj

Cutting holes suitable for fixing 300mm sweep Exhaust fans through brick walls built in cement mortar and making good around the holes in cement mortar 1:3 complete all as specified and directed.

S&F, 1 x 18 watt, LED tube light fitting basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, LED Decorative luminaire with suitable for lamps LED light high efficiency LED driver, optimized heat dissipation for ensuring high LED life span complete all as specified and directed.

M&L, earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth strip of 25x4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth strip of 25x4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 40 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 40 mm bore light grade 7.5m.

K K Construction Co

Shree Builders

divyarsh entrprise

Ramdev and Sons

M.A. MUNSHI AND CO.

Haritwal traders

SNEH TRADERS