Construction 50 bedded Hospital at Mandap in Tehsil Dharampur Distt. Mandi (H.P.)

Amount

Excavation in hilly areas in all heights and depths and in all kinds of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rocks, hard rocks, chiseling/ wedging out of rock (where blasting is prohibited) and other intermediate classification of soil, setting out true to the required lines, grades width cutting and trimming of side slopes and level as shown in the drawing and as directed by the Engineer-in-Charge at site according to the MORD technical specification 2014 clause 1603.1, 1603.2 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of the road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus un-useful material to acquired width of the road or on approved dumping sites through all modes of transportation including head load or animals transport or mechanical means alongwith its leveling fine dressing and carriage of machineries, materials, tools equipments and safety measures and other incidentals necessary to complete the work by mechanical means and/or labour if required. Any loss to the public/private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be duly compensated by him in all cases as per direction of the Engineer-in-Charge including carriage of material within all leads and lifts. A recovery of useful stone for 4767.49cum (four thousand seven hundred sixty seven decimal four nine) cubic metre @ Rs. 300/- (Rupees Three hundred only) per cubic metre shall be effected on pro-rata basis in each running bill from this item. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Excavation in foundation, trenches etcetera in all classification of soil such as pick work, jumper work, blasting work soft rock and hard rock including chiselling wedging and any other mixed variety in dry or saturated conditions upto any depth and lift including pumping and bailing out water where required including stacking the serviceable and unserviceable materials separately as directed and then returning the stacked soil in fifteen centimeters layers when required into plinth and sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus un-serviceable excavated earth within all leads and lifts as per directed by the Engineer-in-Charge including entire carriage of material with in all leads and lifts, disposed materials to be neatly dressed and levelled including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drains and parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rocks, chiseling/wedging out of rocks (where blasting is prohibited) as per drawings and technical specification clause 305.1 and as per direction of the Engineer-in-Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto all leads and lift including dressing of sides and bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm (One hundred fifty millimetre) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water) upto any depth and any quantum of water including cleaning of slush which may arise out during dewatering as per the direction of the Engineer-in-Charge and carriage of material within all leads and lifts and other incidentals The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Excavating trenches of required width for pipes, cables, etc in all classification of soil such as pick work, jumper work, blasting work soft rock and hard rock including chiselling wedging and any other mixed variety in dry or saturated conditions upto any depth and lift including pumping and bailing out water where required including stacking the serviceable and unserviceable materials separately as directed and then returning the stacked soil in fifteen centimeters layers when required into plinth and sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus un-serviceable excavated earth within all leads and lifts as per directed by the Engineer-in-Charge including entire carriage of material with in all leads and lifts, disposed materials to be neatly dressed and levelled including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete including entire carriage of material with in all leads and lifts, disposed materials to be neatly dressed and levelled including other incidentals. including entire carriage of material with in all leads and lifts, disposed materials to be neatly dressed and levelled including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing form work with mild steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frame of 30x30x5mm (Thirty into thirty into five millimetre) size so as to give a fair finish including centring, shuttering, strutting and propping and centring etc etera with wooden battens and ballies in all heights of propping and centring below supporting floor to ceiling not exceeding 4 (four) meters and removal of the same for insitu-reinforced concrete and plain concrete work upto all floor level in all heights including entire carriage of material with in all leads and lifts, disposed materials to be neatly dressed and levelled including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

In foundation,footings bases of columns etcetera and mass concrete.

In flat surfaces such as soffits of suspended floors, roofs, landings balconies and access platform and the like floor upto any thickness upto all floor levels.

In columns, pillars posts and struts square rectangular or polygonal in plan up to all floor levels .

In beams, cantilevers, girders and lintels, sides and soffits of beams, beams haunching cantilevers bressumers and lintels in all depth /height not exceeding 1 (one) metre depths upto all floor levels

Vertical surfaces such as walls (any thickness) partition and the like including attached pillasters, buttresses plinth and string courses and the like in all floor heights.

Stair Case with sloping or stepped soffits excluding landing except spiral stair upto all floor level.

Providing and laying in position cement concrete of specified grade mechanically mixed and vibrated cement concrete 1:4:8 (One cement: four sand: eight graded/crushed stone aggregate 40mm (Forty millimetre) nominal size) as per specification and curing complete but excluding cost of form work in all work up to plinth level including all heights/depths including entire carriage of material with in all leads , lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying mechanically mixed 1:5:10 (one cement :five coarse sand : ten) graded crushed stone aggregate 40 mm(forty millimetres) nominal size cement concrete in retaining walls, return walls, walls (any thickness) up to all floor level and curing complete excluding the cost of centering, shuttering and finishing in all respect including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying Mechanically mixed and vibrated plain cement concrete M-10 (ten) graded crushed stone aggregate 40 mm (forty millimetre) nominal size) in open foundations and plinths or similar works complete as per drawings and MORD technical specification 2014 for rural roads clause 802, 803, 1202 and 1203 and curing complete including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing weep holes in brick masonry/stone masonry, plain / reinforced concrete abutment, wing walls, return walls, retaining walls and Breast walls with 110mm (One hundred ten millimeter) diameter PVC Pipe made of D-plast finolex having working pressure not less than 4.50 Kg P/Sq cm (four point five Killogramme per Square centimetres) extending through the full width of structures with slope of 1 one (Vertical) : 20 ( Twenty) (Horizontal) towards drawing face complete up to all height as per drawing and technical specifications clauses 614, 709, 1204.3.7 including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying reinforced cement concrete mechnically mixed vibrated design mix M-20 (twenty ) grade cement concrete for reinforced cement concrete work to obtained minium crushing strength of 25N/mm2 (Twenty five ) Newton per millimetres square) with minium cement contents of 400Kg/Cum (Four hundred killogramme per Cubic metres) using cement content as per approved design mix and curring complete, all work up to plinth level excluding the cost of centering, shuttering, including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying Reinforced cement concrete mechnically mixed vibrated design mix M-20 (twenty) grade cement concrete for reinforced cement concrete work to obtained minium crushing strength of 25N/mm2 (Twenty five ) Newton per millimetres square) with minium cement contents of 400Kg/Cum (Four hundred killogramme per Cubic metres) using cement content as per approved design mix and curring complete, for attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level to all floor levels excluding cost of centring shuttering finishing including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying Reinforced cement concrete mechnically mixed and vibrated in reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° (fifteen) Degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement design mix M-20 (twenty)cement concret work obtain minium crushing strenght of 25 N/mm2 ( Twenty three) Newton per millimetre square)with minium cement contents of 400Kg/Cum (Four hundred killogramme per Cubic metres) using cement content as per approved design mix, upto all floor levels including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and laying Mild steel and Medium Tensile steel bars Fe 500D made of SAIL, TATA Tiscon for reinforced cement concrete work including straightening, cutting, bending, placing in position and binding including the cost of binding bars all complete upto plinth level including entire carriage of materials within all leads and lifts and other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying Mild steel and Medium Tensile steel bars Fe 500D made of SAIL, TATA Tiscon for reinforced cement concrete work including straightening, cutting, bending, placing in position and binding including the cost of binding bars all complete above plinth level upto all floor levels including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5( seven point five) in superstructure above plinth level upto all floor level in all shapes and size in cement mortar 1:6 (one cement : six coarse sand) curing complete including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm (one hundred fifty/ two hundred fifty/three hundred) millimetres thick AAC blocks in super structure above plinth level up to all floor level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in superstructure above plinth level up to all floor levels in Cement Mortar 1:3( One cement: three coarse sand) and curing complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement :six sand : Twelve graded stone aggregate 20(Twenty) Millimetres nominal size) with Cement Mortar 1:6( One cement: Six sand) and curing complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Stone filling /Soling under floors tightly hand packed upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and MORD technical specifications 2014 as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Back filling behind abutment , wing walls and return walls complete as per drawings and MORD technical specification 2014 Clause 1204.3.8. with Granular Material including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 35mm ( Thirty five ) millimetres thick ISI marked decorative type factory made flush door shutters conforming to IS :2202 (Part I) core of block board construction with frame Ist class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing lead lined shutters including black enamelled/bright finished M.S. butt hinges with necessary screws including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).WOOD POLYMER COMPOSITE (WPC) FRAME & SHUTTER OF SV WOODS including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 30mm (Thirty) millimetres thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19(ninteen) gauge thickness and size of 19 mm x 19 mm(ninteen into ninteen)millimetres for styles and 15x15 mm(fifteen into fifteen)millimetres for top & bottom rails.PVC FLUSH SHUTTER OF I.S.I. MARK including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm (one point four)millimetres in both directions with wire of dia 0.63 mm (zero point six three) millimetres all complete With 1st class deadar wood beading 62X19 mm (sixty two into ninteen)millimetres including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 300×16mm (Three hundred into sixteen millimetre) nominal size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10(ten) as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete upto all floor levels including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. he rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10(ten) as per IS : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete upto all floor levels including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

200x10 mm ( two hundred into ten millimetre)

150x10 mm ( one hundred fifty into ten millimetre)

100x10 mm ( one hundred into ten millimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 (ten) as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc complete upto all floor levels including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

125 mm (one hundred twenty five millimetre)

100 mm (one hundred millimetre)

75 mm ( seventy five millimetre)

Providing and fixing 19mm thick ( ninteen milimetre) made of action tessa terramite resistant water proof commercial board box including shelves and shutters, the back side of cupboard/ cabinet of 8mm(Eight milimetre) thick ply and cut portions of shelves shall be finished with 6mm six milimetres) hard board edging. The cut portion of shutters from all the sides shall be finished with 12 mm(twelve)millimetres thick hard wood edging. the shutters from out side shall be finished with 1mm thick laminated sheet of approved shade includng piano hinges and magnetic catcher with all ascessories complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing Mild Steel grills of required pattern on wooden/steel frames of windows etcetera with 10mm (ten) millimetres mild steel square bars and welded to 6 x12 mm (six into twelve) millimetres flat. Total grill should be powder coated and as per direction by the Engineer-in-Charge including entire carriage of material with in all leads and lifts and including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 75mmx65mm (seventy five into sixty five) rounded hand rails in straight length complete in 1st class indian teak wood including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and laying 25mm (Twenty five millimetres) thick kota stone 55x55cm (Fifty five into fifty five centimetres) minimum size flooring with 7.5(seven point five) centimetres wide marble band & with coving(NTC/Johnson) of same shadethat of flooring of approved shade mirror polished finshed of uniform colour laid on 20mm (Twenty millimetres) average thick base of cement mortar 1:4 ( One cement : four coarse sand) laid over and joints with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete in all floor level in all heights upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying antiskid vitrified floor tiles of size 600x600 mm (Six hundred into six hundred)millimeters bell with coving(NTC/Johnson) of same shade that of flooring of approved shade with water absorption less than 0.08% (zero point zero eight)Percent conforming to IS: 15622, of approved make Somany /Kajaria /Nitco /Orient RAK, Johnson & Johnson) in all colours and shades, laid on 20mm (twenty)millimetrs thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three killogramme per square meters) including grouting the joints with white cement and matching pigments etc., complete upto all floor level in all heights including entire carriage of material with in all leads lifts and technical specifications as per the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing 2mm(two millimetres thick seamless static pulse venyl flooring 60x60cm (sixty into sixty) centimetres of approved shade of LG hausy with coving of same shade, carbed or mosaic/metalled finish laid with approved adhesive on sub-floor complete upto all floor level in all heights including entire carriage of material with in all leads lifts and technical specifications as per the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying digital ceremic glazed tiles with coving(NTC/Johnson) of same shade that of flooring of approved make of Kajaria , Nitco,Somany,Orient, Rak, Johnson and Johnson in flooring (300x600x10mm size)( three hundred into six hundred into ten millimeter) treads of steps 1.50m (one point five zero metre) high tiles in dada. Laid on a bed of 12mm. (twelve millimetre)Thick cement mortar 1:3 (one cement : three sand) finished with flush pointing in white cement complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying cobble stone / local cut stone / red mandana stone 600x600mm (six hundred into six hundred) 19mm (ninteen) millimetres thick cement mortar 1:4 (one cement :four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c preparing of nosing i/c rubbing and granite polish finish complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm (three hundred into three hundred into nine point eight millimeters) having with water absorption less than 0.5% (zero point five) percent and conforming to IS: 15622 of approved make of Kajaria , Nitco, Somany, Orient, Rak, Johnson and Johnson in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm (twenty millimeter) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. andd curing complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying black finished marble stone flooring with sami round nosing of approved make of in design and pattern, in landing of stair as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (twenty millimetre)(average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete upto all floor level as specified and as directed by the Engineer-in-Charge Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing white/ coloured Glazed tiles Ist quality 300mm to 450 mm ( three hundred millimetres to four hundred fifty millimetres) thick in skirting risers of steps and dado 12 (Twelve) millimetres thick cement mortar 1:3 (one cement :three sand) and jointed with cement slurry of make KAJARIA , Nitco, Somani, Johnson including entire carriage of material with in all leads and lifts and including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and laying 40 mm thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate) finished with a floating coat of neat cement, slurry complete upto all floor level in all heights including entire carriage of material with in all leads lifts and technical specifications as per the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing prepainted sandwich made of tata dura shine puffed roofing with top skin of 0.60 (Zero point six zero) millimetres thick sheet over steel trusses made of cold rolled steel coil with epoxy coating of 25(twenty five) micron having a puff depth of 50 mm (fifty millimetre) and weight of puff 35-37 (thirty five to thirty seven) steel frames are to be painted of approved shade i/c fixing with screws prepainted iron J or L hooks, bolts and nuts with prepainted limpet and rubber washers complete with all accesories as required including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing ridges or hips 60cm (sixty centimetre)overall with 0.60mm(zero point six zero) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20(twenty) microns over 5 (five)microns primer coating + bck coat of polyster of 5 (five)microns over 5(five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia and prepainted G.I limpet and bitmen washers complete with all accessories as including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 30(Thirty) Centimetres wide 30(Thirty) Centimetres overall semicircular 0.63 (Zero point six three)millimetres thick plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing M.S. BP Sheet 1.66 mm to 2.00 mm (One point six six to two Millimetres) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely). including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing on wall face unplasticised Rigid PVC 110mm ( one hundred ten milimetre ) of (Finolex/Supreme confirming to IS 13592-92)make for rain water pipes of working pressure not less than 4.00 kg/square centimetre ( four point zero zero kilogram per square centimetre ) including filling the joints with approved adhesive complete upto all floor level in all heights including carriage of material up to all leads and lifts and as per direction of Engineer in charge. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid uPVC rain water pipes of Supreme, AKG, Finolex, make conforming to IS : 13592-92 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimetre) gap for thermal expansion complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals.

110mm (One hundred ten millimetres) nominal size PVC bend

110mm (One hundred ten millimetres) nominal size PVC Shoe

Providing and fixing 110 mm ( one hundred ten millimetre) unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm ( fifty into fifty into fifty millimetre)hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete upto all heights complete including carriage of material up to all leads and lifts and as per direction of Engineer in charge. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing everest desigener fiber board ceiling tiles of size 600x600 mm. (six hundred into six hundred) millimetres over readymade Powercoated metal sheet section frame work 600mm C/C( Six hundred centre to centre grid suspended from roof, including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing ACP tiles ceiling 60x60cm ( sixty into sixty) centimetres (frame work to be measured and paid for separately) including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Steel work welded in built up sections made of TATA ,in grating, framed guard bars ladders, railing brackets and similar works , including cutting, hoisting, fixing in position and applying a priming coat of red lead paint upto all floor level in all heights complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Structural steel work riveted, bolted or welded in built up sections made of TATA, in trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. upto all floor level in all heights complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Steel work in built up tubular sections made of TATA(round, square or rectangular hollow pipes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete upto all floor level in all heightscomplete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt. .

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm (fifty) millimetres dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely)including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing MS railing for stair case having balluster of 19mm x19mm (ninteen into ninteen) millimetres and 12mm x12mm (Twelve into twelve )millimetres solid square bar with a clear height of 90cm (Ninety) millimetres embedded in cement concrete steps and jointed with electrical/gas welding at top along with MS flat of 40mmx6mm (Forty into six) millimetres size complete applying priming coat of red lead paint as per drawing specification including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing door frame made of ECO - 5000 Series galvanised powder coated steel section of 1.2mm ( one oint two milimetre ) thick galvanised steel ( Base steel as per IS 513 ) with zink of 120 gms/ Sq. mtr. ( one hundred twenty grams per square metre )powder coated with pure polyster powder upto 50-60 micron thick with rebate of 37mm ( thirty seven milimetre ) for shutter. The frame section should be cut to length and metre joined with corner brackets made of CRCA electroplated. The frame should be provided with ( a) 3 Nos. of M.S. powder coated 4" ( four inch ) Butt hinges of 2mm ( two milimetre ) thickness welded to the frame. (b ) 6 Nos. of 1.2mm ( one point two milimetre ) thick CRCA electroplated stiffeners should be welded to frame. ( c ) 6 Nos. of 8" ( eight inch ) M.S. hold fasts with split end tail welded to stiffener plates. ( d ) One No. aldrop receiver (e ) Each frame should be provided with 25x50mm ( twenty five into fifty milimetre ) tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer.Sections should be with Primer Coat of Epoxy Primer of 5-7 micron ( five to seven ) thick, finish painted with Polyester Paint of 12-16 ( twelve to sixteen ) microns thick and back coated with Alkyd backer of 5-7 ( five to seven ) microns, or Powder Coated with pure Polyester Powder up to 50-60 ( fifty to sixty ) microns thick. The entire frame should be provided with a coat of etch primer. including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

105 x 60mm ( one hundred five into sixty milimetre ) ( Single Rebate )

125 X 60MM ( one hundred twenty five into sixty milimetre ) ( Double revate )

Providing and fixing windows Eco 5000 series febricated from roll formed sections made of Galvanised Steel Colour Coated/ Powder Coated ( Base steel as per IS 513 "D" quality, Galvanized as per IS 277 with Zinc of 120 grams / Sq. Mtr. ) ( one hundred twenty grams per square metre ) with total coated thickness of 0.60mm ( zero point milimetre ) Paint Specuification:- Sections should be with Primer Coat of Epoxy Primer of 5-7 micron ( five to seven ) thick, finish painted with Polyester Paint of 12-16 ( twelve to sixteen ) microns thick and back coated with Alkyd backer of 5-7 ( five to seven ) microns, or Powder Coated with pure Polyester Powder up to 50-60 ( fifty to sixty ) microns thick. Dimensions of Sections:- Section for Frame should be of 98mm x 50mm, ( ninety eight milimetre into fifty milimetre ) section for Mullion should be of 46mm x 70mm, ( forty six milimetre into seventy milimetre ) Section for Shutter Frame should be of 46mm x 46mm,( forty six into forty six milimetre ) Section for fixed Glass Bead should be of 18mm x 25mm (eighteen milimetre into twenty five milimetre ) and Section for fly mesh Shutter Frame should be of 20mm x 40mm.( twenty into forty milimetre ) Fixing Details:- Frame and mesh Shutter Sections should be cut to length and metre joined with Corner Bracket made of Polyepropylene. Glass Shuttter should be mitre joined with corner bracket made CRCA electroplaed. Mullion Section should be joined with Frame/ Mullion using Nylon Mullion Cap Ethy Propylene Diamine Monomer ( EPDM) Gasket should be used all around glass in shutter between frame and Glazed Shutter and both sides of Fixed Glass. Rubber Gasket should be used around Fly mesh to fix Mesh in Mesh Shutter. 4mm (Four) millimetres thick glass shall be fixed to all window shutters. Accessories:- Each Glazed Shutter should be provided with MS Powder Coated Friction Hinges -I set, High Grade Aluminum Powder Coated Handle -1 No. Each Mesh shutter should be provided with S.S. Pivot Hinges -1 set, Seccolor make handle shall be provided per shutter. Window Frame should be fixed to brick/concrete masonary by using Nylon self expanding caps and driving MS electroplated 80mm ( eighty milimetre ) long screws into the caps through frames including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

6mm (Six millimetre) thick cement plaster to ceiling in cement mortar 1:3 ( One cement :three sand) upto all floor level including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

6 mm (Six millimetre) thick cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams upto all floor level and curing copmplete, including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

15mm (Fifteen millimetres) cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth in cement mortar 1:6 (One cement : six coarse sand) upto all floor level in all heights and curing complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

15mm (fifteen) millimetres Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty) millimetres in girth and finished even and smooth cement mortar 1:3(One cement :three sand) upto all floor level in all heights and curing complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

15mm (Fifteen millimetres) cement plaster in single coat on fair side of brick/ concrete /stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers, and/or rounded angles not exceeding 80mm (Eighty) millimetres in girth and finished even and smooth in cement mortar 1:6 (One cement : six coarse sand) upto all floor level in all heights and curing complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and applying BARIUM SOLPHATE PLASTER over plastered surface to prepare the surface even and smooth complete upto all floor level in all heights and curing complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

12 mm (twelve millimetre) thick cement plaster with cement mortor 1:3 (one cement : three sand) finished with a floating coat of neat cement upto all floor level and curing copmplete, including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Applying priming coat of ICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar. make With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade two or more coat applied @ 0.90 ltr/ 10 sqm (zero point nine liters per ten square metre)over an under coat of primer applied @ 0.80 ltr/ 10 sqm (zero point eight liters per ten square metre) of approved brand and manufactureICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar make including cleaning the surface of all dirt dust and other forign metter complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Applying one or more coats of wood primer with ready mixed pink or Grey primer of ICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar make on new wood surface after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm(zero point nine liters per ten square metre) over an under coat of primer applied @0.75 ltr/10 sqm(zero point seven five liters per ten square metre) of approved brand and manufacture of ICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar. make including cleaning of all dirt, dust and other foreign matter sand papering and stopping complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Finishing walls with weather proof water based acrylic Emulsion appling @ 3.84 Kg/10 sqm (three point eight four kilograme per ten square metre) over and including one coat of special primer applied @ 0.75 ltr /10 sqm (at the rate zero point seven five liters per ten square metres) premium acrylic washable emulsion paint of approved shade of asian paint / Nerolac paint Dulux paint system for interiors and exteriors using Primer as per manufacturers of ICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar make including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Finishing with Synthetic enamel paint Two or more coats applied on walls @ 1.25 ltr/10 sqm (at the rate one point two five liters per ten square metres) over and including one coat of special primer applied @ 0.75 ltr /10 sqm (at the rate zero point seven five liters per ten square metres) premium acrylic washable emulsion paint of approved shade of asian paint / Nerolac paint Dulux paint system for interiors and exteriors using Primer as per manufacturers of ICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar make including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government

Distempering with Synthetic/Acrylic oil bound distemper of asian paint / Nerolac of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

White washing with lime on undecorated wall surfaces two coats to give and even shade including thoroughly brooming the surface to remove all dirt, dust mortar dirt and other foreign matter complete upto all floor level in all heights complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Finishing walls with Epoxy paint (two or more coats) of ICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar make including appropriate priming coat of approved quality preparation of surface, etc. complete. including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Applying Birla white wall care putty over plastered surface after thoroughly brushing the surface free from mortar droops, dust, loose materials and other foreign matter sand papered smooth to give final matter finish to the surface complete upto all floor level in all heights including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Making plinth protection 50mm (fifty millimeter) thick in cement concrete 1:3:6 (one cement : three sand six graded crushed stone aggregate 20mm (twenty millimeter) nominal size) over 75 mm(seventy five millimetres) thick bed of dry brick ballast 40 mm(forty millimetres) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling and derssing and finishing the top smooth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Constructing Coursed rubble hammer dressed 'U' shape open surface drain with side wall. 15 X 23 cm (Fifteen into twenty three centimeter ) in cement mortar 1:6 ( One Cement : Six approved Sand) and inside plastering with cement mortar 1:3 (One Cement: Three approved Sand) including earth work and laying 10 cm (Ten Centimatre ) cement concrete in 1:5:10 (One Cement : Five approved Sand : Ten graded crushed stone aggregate) of 40 mm (Forty millimetres) nominal size and 7.5 cm (seven Point Five Centimatre ) cement concrete 1:2:4 (One Cement : Two approved Sand : Four graded crushed stone aggregate of 20 mm (Twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Loosining of the ground up to a level of 300 mm (three hundred millimetre)below the sub grade level, watered graded and compacted in layers to meet requirement of table 300.1 and 300.2 for subgrade construction as per technical specification clause 303.5.2 and including entire carriage of material with in all leads and lifts and as per drawings and MORD technical specifications 2014 as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Construction of granular sub base by providing well graded materials grading -1 spreading in uniforms layers with tractor motor grader on prepared surface, mixing by mix in place method with rotvator at OMC, and compacting with wheel roller of 80 to 100 KN ( eighty into hundred) static roller to achieve the desired denisty, complete as per MORD technical specification 2014 Clause 402 including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN ( eighty into hundred ) static roller weight to achieve the desired density including lighting, barricading and maintenance of diversion, etcetra as per Tables 400.11 and 400.12 and MORD Technical Specification 2014 Clause 406 by mechnical means including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and applying priming coat with bitumen Emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer @ 0.70 to 1.00kg/sqm (Zero point seven zero to one point zero kilogram per square metre ) using mechanical means as per MODR Technical Specification 2014 Clause 502 including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 Kg to 0.30 Kg per sqm (Zero point two five to zero point three zero kilogram) per square metre on prepared surface and cleaned with hydraulic broom as per MODR Technical Specification 2014 clause 503 including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and laying 30(Thirty millimetre) thick bituminous concrete with 100-120 ( Hundred dash One hundred twenty) TPH batch type hot mix plant producing an average output of 75(Seventy five) tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 (Five point four to five point six) percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MODR Technical Specification 2014 clause 507 complete in all respects including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing Solar heating panel(BOSCH) approved ISI make complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Total civil work

Providing and fixing 15(fifteen) millimetres nominal bore galvanised mild steel tubes ( heavy grade) made of B.S.T., Jindal (Hissar), Tata Steel Tubes Ltd., Prakash Surya tube for external work and floors, fitting and clamps including making good the wall, ceiling and floor including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and laying in trenches galvanised mild steel tubes 20 mm (Twenty milimeter) JINDAL(HISAR)/ TATA STEEL TUBE LTD ( heavy grade )tube fittings (earth work in trenches to be measured and paid separataly) including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and laying in trenches galvanised mild steel tubes 20 mm (Twenty milimeter) millimetres nominal bore galvanised mild steel tubes ( heavy grade) made of B.S.T., Jindal (Hissar), Tata Steel Tubes Ltd., Prakash Surya tube for external work and floors, fitting and clamps including making good the wall, ceiling and floor including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Making connection of galvanised steel distribution branch with galvanised mild steel mian 25 to 40 (Twenty five to forty )millimetres bore by providing and fixing tee including cutting as threading the pipes complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00(one ) metre spacing for INTERNAL WORK - EXPOSED ON WALL. This includes testing of joints complete as per direction of the Engineer-incharge.including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

1216 (16 mm O.D. pipe)(One thousand two hundred sixteen( Sixteen millimetres outer dia pipe)

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply,capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete for external workas per direction of the engineer in charge including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

1216 (16 mm O.D. pipe)(One thousand two hundred sixteen( Sixteen millimetres outer dia pipe).

Providing and fixing water closet squatting pan of Hindware/Cera (Indian type W.C. pan ) with 100 mm( One hundred) millimetres sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the wall and floors wherever required:White Vitreous china Orissa pattern BIG SIZE ORRISA PAN NO. 20004 size 580X400 mm(Five hundred eighty into four hundred). WITH LOW LEVEL P.V.C. CISTERN OF of Perryware/Jaquar/ Hindware/Cera IN WHITE SHADE including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing vitreous china dual purpose closet European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 (ten) litre low level flushing cistern with fitting and brackets, 40 mm (forty millimetres) flush bend, 20 mm(twenty millimetres) over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend. (ONE ANGLO INDIAN W.C. UNIVERSAL WITH CISTREN CAT. 20012. the size is 81x50x80cm (eighty one into fifty into eighty) centimetres of Perryware/Jaquar/ Hindware/Cera) including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan NO.20011) with seat and lid in white shade of Hindware/Cera with seat and lid, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan NO.20012 WITH JET PRESSURE) with seat and lid in white shade of Hindware/Cera with seat and lid, 10 (ten) litres low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

PProviding and fixing white vitreous china flat back large no 60001or wall corner type lipped front urinal basin of430x260x350 mm (four hundred thirty into two hundred sixty into three hundred fifty) millimetres and 340x410x265 mm (three hundred forty into four hundred ten into two hundred sixty five) millimetres sizes respectively with automatic flushing cistern in white shade of Jaquar/ Hindware /Cera with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 (five) litre white P.V.C. automatic flushing cistern with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government..

Providing and fixing viterous China wash basin N0 10001 SIZE 550x400x830 mm (five hundred ten into four hundred millimetre) in White Shade of superime quality Parryware, Hindware Sanitaryware, Neycer, Cera including cutting holes & making good the same and carriage of materials within all leads and lifts complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing wash basin in white shade with C.I. brackets, 15 mm (fifteen) millimetres C.P. brass pillar taps, 32 mm (thirty two) millimetres C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:UNDER COUNTER WASH BASIN ZEN CATEGORY No. 10049 SIZE 56 X 43 CM( Fifty six into forty three) centimetres the tap shall be elbo or foot opreated complete of Hindware/Parryware /CERA, Sanitary ware, Naycer make upto all floor level including entire carriage of material with in all leadsand lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing white vitreous china pedestal of Parryware, Hindware Sanitaryware, Neycer, Cera. for wash basin completely recessed at the back for the reception of pipes and fittings including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing Stainless Steel A ISI 304 (18/8) (eighten/eight) kitchen sink size 470x420 mm ( four hundred seventy into four hundred twenty) millimetres bowl depth 250 mm ( Two hundred fifty ) millimetres of AMC, UNIK, DIAMOND, Neelkanth. make as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (forty millimetres) including painting of fittings and brackets, cutting and making good the walls wherever required upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing 32 mm (thirty two milimetre) dia P.V.C. waste pipe Finolax make for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and Fixing Soap dish stainless steel CAN -1531of Jaquar or equivalent complete in all respectupto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing C.P. brass ISI marked IS. No. 8934 toilet paper holder JAQUAR,ESS-ESS make including the carriage of material within all leads, lifts through all modes of transportation as per direction of the Engineer-in-charge and other incidentals. The rate is includes of octroi, royality, Malkana, toll tax , GST, sale tax or other taxes imposed by the Government.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass make of Atul Modi Guard, Golden fish mounted on 6mm (six millimetre) thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washer including the carriage of material within all leads, lifts through all modes of transportation upto all floor level as per direction of the Engineer-in-charge and other incidentals. The rate is includes of octroi, royality, Malkana, toll tax , sale tax GST or other taxes imposed by the Government.

Providing and fixing CP towel rail complete with CP brass brackets fixed to wooden plugs with CP brass screws 600 mm ( six hundred millimetre long towel rail width 78 mm ( seventy eight millimetre) and effective height of 88mm ( eighty eight millimetre) weight not less than 190 gms (one hundred ninety grams)of Kingstone, Gem, Parko, Techno, Jal, ESS, Seiko, Modi ,JAQUAR make including entire carriage of material with in all leads and lifts and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 100 mm (one hundred) millimetres dia cromium plated grating JAL, ESS-ESS of superior quality for floor, gully or nahani trap complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 15mm (Fifteen) millimetres dia PTMT push cock tap with spout No. 3821, Superior heavy type of made JAL, ESS ESS, Kingstone, Gem, Parko, Techno, Seiko, jaguar including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing PTMT bib cock fancy tap No 12 of 15mm (Fifteen millimetres) dia ( Superior heavy type ) of made JAL, ESS ESS, Kingstone, Gem, Parko, Techno, Seiko, jaguar including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing plasticised PVC connection pipe Finolex make with brass unions 450mm ( four hundred fifty millimetre) length 15mm (fifteen millimetre) nominal size upto all floor level. including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing ball valve (brass) JAL, ESS-ESS of approved quality, High or low pressure, with plastic floats complete complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

15 mm (fifteen millimetre)nominal bore

20 mm (twenty millimetre)nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points JAQUAR, JAL-ESS of approved quality conforming to IS:8931 complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite Brass full way valve with C.I. wheel of approved quality (screwed end) :25 mm (twenty five) millimetres nominal dia complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing PVC water storage tank of Sintex three layer make (I.S.I. 12701 marked tripple layer) G.I. inlet or out let connection15mm (Fifteen) millimetres nominal bore ball valve and mosquito proof PVC cover with locking arrangement including providing pads of required size of inlet or outlet, compete in all respect including hoisting upto all floor level above ground level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing 110 mm x 75 mm (one hundred ten milimeters into seventy five millimeters) PVC Finolex make floor trap working pressure 6.00 Kg(six) per square centimetre (six kilogram per square centemtre) I.S.I. marked of self cleaning design including fixing with approved adhesive including cost of cutting and making goods the walls and floors etc. complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing, laying and jointing 110 mm (one hundred ten millimetre) diameter glazed stoneware pipes class SP-1(one) with stiff mixture of cement mortar in the proportion of 1:1 (one cement : one fine sand) including testing of joints etc. complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and laying 100 mm (one hundred millimetre) diameter S.W. pipe all round cement concrete 1:5:10 (one cement : five coarse sand :ten graded stone aggregate forty millimetres) nominal size including bed concrete as per standard design complete including entire carriage of material with in all leads and lifts and as per drawings and MORD technical specifications 2014 and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes 2.7 (two point sewven) millimetre thick of FINOLEX / SUPREME make ISI marked including fixing with approved adhesive etc. complete including entire carriage of material with in all leads and lifts and as per drawings and MORD technical specifications 2014 and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

75 mm (Seventy five millimetre) diametre

110 mm (one hundred ten millimetre) diametre

150 mm (one hundred fifty millimetre)diametre

Providing and fixing PVC door bend with ovalaccess door, insertion rubber washer 3 mm (three millimetres) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

I) 110mm dia (one hundred ten )millimetrediametre

II) 150 mm dia (one hundred fifty) millimetre diametre

Providing and fixing PVC single equal branch with oval access door, ISI marked of Finolex make insertion rubber washer 3 mm (three millimetres) thick bolts and nuts complete including fixing with approved adhesive etc. Complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

I) 110mm (one hundred ten millimetre) dia

II) 150mm (one hundred fifty millimetre) dia

Providing and fixing PVC double equal branch with oval access door, ISI marked of Finolex make insertion rubber washer 3 mm (three millimetres) thick bolts and nuts complete including fixing with approved adhesive etc. Complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

I) 110mm (one hundred ten millimetre) dia

II) 150mm (one hundred fifty millimetre) dia

Providing and fixing PVC Collars ISI marked of Finolex make including fixing with approved adhesive etc.complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

I) 110mm (one hundred ten millimetre) dia

II) 150mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain bend ISI marked of Finolex make including fixing with approved adhesive etc. complete.including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

I) 150mm (one hundred fifty millimetre) dia

II) 110mm (one hundred ten millimetre) dia

Providing and fixing U shaped wall mounted rail with hings 600x 100 mm ( Six hundred into one hundred millimetre ) Cat No. B2210107 and wall mounted grab bar 600 mm ( six hundred millimetre) long CAT No. B2210106 jaguar or equivalent superior quality complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing Exhaust fan ISI marked including fixing with approved adhesive etc. complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing square-mouth S.W. gully trap class SP-1(one) complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm (three hundred into three hundred millimetre) size (inside) the weight of cover to be not less than 4.50 kg (four point five zero kilograme) and frame to be not less than 2.70 kg (two point seven zero kilograme) as per standard design:100x100 mm (one hundred inti one hundred millimetre) size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5(seven point five) complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt

Providing and fixing C.I. cover without frame for manhole required shape and approved quality rectangular shape 455x610 mm (four hundred fifty five into six hundred ten milimetes) light duty the weight not less than 23Kg ( twenty three kilograme) including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Constructing masonry Chamber 60x60x75cm (Sixty into sixty seventy five Centimetyres) inside, in brick work in cement mortar 1:4 (one cement : four coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm (one hundred sixty) millimetres bottom diameter and 180 mm (one hundred eighty) millimetres deep ( inside) with chained lid and RCC top slab 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20mm (Twenty millimetres) nominal size , i/c necessary excavation, foundation concrete 1:5:10 ( one cement : five sand : ten graded stone aggregate 40 mm (forty) millimetres nominal size) and inside plastering with cement mortar 1:3 (one cement :three coarse sand) 12 mm(Twelve) millimetres thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(nonmodular) bricks of class designation 7.5 (seven desimal five) millimetres including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Constructing brick masonry chamber size inside dimensions 455 x 610 and 450 mm (four hundred fifty five into six hundred ten and four hundred fifty) millimetres deep single pipe line.for under ground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement : five sand ) C.I. Cover with frame (lightduty ) 355 x 610( three hundred fifty five into six hunderd ten) millimetres internal diamensions total weight of cover with frame to be not less than 38 (thirty eight ) Kilogramme (weight of cover 23 (twenty three) Kilogramme and weight of frame 15 ( Fifteen) kilogramme R..C.C top slabe with 1:2:4 mix (one cement : two sand : four graded crushed stone aggregate 20 (twenty) millimetres nominal size ) foundation concrete 1:5:10 ( one cement : five sand : ten graded crushed stone aggregate 40( Forty millimetres nominal size) inside plaster 15mm thick with cement mortar 1:3 (one cement : three sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

M/s Surindera Traders

Unipro Techno Infrastructure Pvt Ltd