SPECIAL REPAIRS TO BLDG NOS T 35 AND T 06 REPLACEMENT OF DOOR WINDOWS OF BLDG NOS T 124 NP 115 AND NP 116 AND COOK HOUSE NEAR BLDG NO T 106 AT MIL STN DHRANGADHRA

Amount

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation complete all as specified and directed.

Removing excavated material (Soil) not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in padding on roof using integral water proofing compound @2% by Wt. of Cement, finishing cement concrete surface even and smooth without using extra cement, complete all as specified and as directed. (WPC will be measured and paid separately).

M&L for PCC 1:2:4 type B2 (using 40 mm graded as in bed blocks etc. complete all as specified and directed.

M&L for providing cement concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in coping, including necessary form work complete all as specified and directed.

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in padestal/coping, bed block for post, including necessary form work, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry Type B1 1:2:4 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in landing / cover slab etc setting in CM 1:6 complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, Type B1 (using 20 mm graded granite stone aggregate) for slabs suspended on walls, beams and columns, in floors, roofs, landings and in shelves and the like complete all as specified and directed.

Supply only, integral water proofing compound complete all as specified and directed.

M&L for water proofing treatment to existing non-accessible roof slabs by providing 10mm thick bedding layer of cement morter (1:3) mixed with water proofing compound as per manufacturer's instruction and applying one coat of bituminous/polymerized primer confirming to IS-3384 @ 0.30 Ltr/Sqm and laying of actetic polypropylene (APP) modified membrane pre-fabricated, reinforced with non-woven polyester of 3.50Kg/Sqm (minimum), 3mm thick (minimum), with minimum 75mm side overlaps and 100mm end overlaps and applying one coat of bituminous aluminium paint over APP membrane complete including taking down existing water proofing treatment with bedding layer of cement mortar complete and removal of debries out side MD land all as specified and as directed. Note:- Supply only water proofing compound shall be measured and paid separately.

M&L cutting holes in stone walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, Exc. Half brick but not exc. One brick, Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall

M&L for walling of random rubble stone masonry, uncourses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified and directed.

M&L for extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

M&L for formwork to flat fair finished surfaces of concrete of chullah hoods, chajjas, troughs, slab, shelf and similar items including edges complete all as specified and directed.

M&L for 35mm thick Ist class hard wood, glazed and skelton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars) ,edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a). Note :- Wire cloth etc shall be measured and paid seperately.

S&F, Ist class hard wood 35 mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of 12 mm veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F, factory made, 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for flush shutters 30mm, solid core construction, with particle board core and ply wood face panels, commercial type on both sides complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each and refixing in same opening after easing and adjustment complete all as specified and directed.

Taking down shutters of any description nexc 1 sq.m each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each completed all as specified and directed.

Taking down old shutters of any description exc. 1 sqm but not exc. 2 sqm each and refixing in same opening after easing and adjustment complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

S&F, in repair, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, in repair, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 100 mm and fixed complete all as specified and directed

S&F, in repair, aluminium anodised, barrel tower bolts of extruded section with length of bolt 100 mm and fixed complete all as specified and directed

S&F, Aluminium anodised barrel tower bolt of extruded section and fixed 150 mm long complete all as specified and directed

S&F, in repair, Aluminium anodised barrel tower bolt of extruded section and fixed 150 mm long complete all as specified and directed

S&F, Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long complete all as specified and directed

S&F, Butt hinges med weight cold rolled mild steel and fixed 100mm size complete all as specified and directed.

M&L for 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F, continuous (piano) hinges, mild steel bright finish or electrogalvanised, width of flap 40 mm complete all as specified and directed.

S&F, for extruded aluminium alloy handles, fabricated type, anodised 100mm size complete all as specified and directed.

M&L in repair, extruded aluminium alloy handles, fabricated type, anodised 100mm size complete all as specified and directed.

S&F, extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, in repair, extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, Mortice lock, brass, four lever, verticle type, size 100mm complete all as specified and directed.

S&F, in repair, Mortice lock, brass, four lever, verticle type, size 100mm complete all as specified and directed.

S&F, hasp & staples 125mm in size, safety type alu. anodised fixed with screws complete all as specified and directed.

S&F, in repair brass chromium plated, tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed.

S&F, in repair, 20mm dia, stainless steel, fancy type,tubular curtain rod fix on decorative brackets with decorative globe at both end complete all as specified and directed.

S&F, in repair, stainless steel, fancy type Brackets decorative with fancy type globe at both end curtain rod for 20mm dia curtain rod complete all as specified and directed.

S&F, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F, in repairs, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F, Door closer hydraulically regulated, Aluminium (extruded section body) designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F, in repair, Door closer hydraulically regulated, Aluminium (extruded section body) designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, in repairs, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F, mild steel bolts, purpose made,with hexagonal or square head one end and screwed the other,or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long dia of neck in exc 12 n.exc 20mm complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inclding cranking, bendiing spirally for hooping for columns, hooking ends and biinding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F, Rolled section as in main and cross beam hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates. Gde Fe 410-S complete all as specified and directed.

S&F, Rolled section as in main and cross beam hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates. Gde Fe 410-S including one shop coat of zinc chrome primer complete all as specified and directed.

S&F, mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F, mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F, Mild steel for roof trusses (framed), trussed purlins, crane gantires, rails and fasternings and heavy bracket framming (beam, tee, angle, channel or flat sections ) incuding distance pieces, clats etc. and confirm to Gde- Fe-410-0 or Fe 310-0 including one shop coat of zinc chrome primer complete all as specified and directed.

M&L for rolled mild steel angle iron or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

M&L for rolled mild steel angle iron or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete including the foregoing items if structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) all as specified and directed.

S&F, welded steel wire fabric, cut to length, fixed to steel members/reinforcement steel, weigh per Sqm not exc. 4 Kg complete all as specified and directed.

S&F, factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F factory made steel windows with side hung shutters incl projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded including applying one shop coat of red oxide primer complete.

S&F factory made steel ventilators with top hung shutter including hinges steel peg stay including applying one shop coat of red oxide primer complete.

S&F, Aluminium anodised windows/ ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- sheet glass, wire cloth, lock, etc shall be measured and paid seperately.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction.

S&F, in repairs, of anodised aluminium grill made with 6 mm bars made to shape, DG-104 including U/F/H aluminium channel/ sections complete all as specified and directed. Note :- (i) Fabrication work shall be got done from approved fabricator of manufacturer of alluminium sections. (ii) Sample of grill shall got approved by the GE in writing.

S&F, Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F, Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. complete all as specified and directed.

M&L for 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, as in aluminium door panels/partition of any size fixed with screws to timber frame work complete all as specified and directed.

S&F, 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber frame work in cup boards, rebated or flat edged fixed in repairs complete all as specified and directed.

M&L for 6mm thick external teak wood lipping fixed to18/19mm thick block or Veneered particle boards with nails complete all as specified and directed.

M&L for machine cut kota stone slab, 450x600mm ( 18"X24"), 20-25mm thick as in flooring laid over and including cement mortar screed bed of 15mm thick in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

M&L for rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75mm thick cement concrete type C2 1:3:6 (40mm graded aggregate) complete all as specified & as directed.

M&L for 25 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and as directed by Engineer - in - Charge

M&L for joint free coloured glazed ceramic tiles of size300x200/ 350x250x7mm/ 450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size300x200/ 350x250x7mm/ 450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for Non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for Non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for Non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm as in dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick (compacted thickness) sand cushion below paver blocks including takingout old paver block floor complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 450 x 350 x 7mm thick High lighter tiles on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1;4 complete all as specified and directed.

M&L for heavy duty, exterior grade ceramic tiles of size 300 x300x 10mm thick, set, jointed and pointed in neat cement slurry in trades/risers, landing with white cement and pigment over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

M&L for chequered cement concrete tiles 20 cmx20 cmx20 to 25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry over and including 15 mm thick screed bed in CM (1:6) as in floor complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for 10mm thick rendering in CM (1:3) to concrete surface of ceiling finished even and smooth all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed. (Note :- Water proofing compound shall be measured and paid separately)

M&L for preparation of old decorated plastered or unplastered surfaces of wall including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on wall complete all as specified and directed.

M&L for preparing of old plastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for preparing of old plastered or un-plastered wall surfaces and applying one coat of oil bound distemper on plastered surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of cement base paint complete all as specified and directed.

M&L for complete removal of existing treatment of wall with mechanical scrubber and applying two coat of cement base paint over one coat of primer complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

M&L for 3mm thick sheet glass is ground or obscured or frosted, on one side, pin headed type and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane complete all as specified and directed.

S&F, 4.8 mm thick Sheet glass, ordinary quality ,in square exc. 0.5 Sqm in each pane with necessary rubber gaskets complete all as specified and directed.

S&F, 3 mm thick fugured glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane

Hacking out old broken glass (any thickness, size, quality or description) not exc 0.5 Sqm each pane from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all,as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complte all as specified and directed.

M&L for preparing surface of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint and Sanding newly tarred or painted surfaces with clean sharp sand

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM 1:3 mix , 40mm thk in two coats, using polymer SBR Latex or equivalent as approved @ 5 Ltrs per 50 Kg bag of cement complete all as per manufacturer's Specifications/instructions and as directed. Note :- (New reinforcement or Welded wire fabric) will be measured and paid separately)

Taking up or down steel tubing and connections complete all as specified and directed for 15mm bores of pipe complete all as specified and directed.

Taking up or down steel tubing and connections complete all as specified and directed for 20mm bores of pipe complete all as specified and directed.

Taking up or down steel tubing and connections complete all as specified and directed for 25mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for 15mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for 20mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for 25mm bores of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 15mm bores of pipe.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 20mm bores of pipe.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 25mm bores of pipe.

S&F, 32mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

Supply, hoisting, fixing in position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

S&F, in repair, bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

Supply only Pillar taps cast copper alloy with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, in repair, Pillar taps cast copper alloy with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, in repairs, stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, in repairs, 20mm bore dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F, in repairs, 25mm bore dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Supply only 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F, in repair, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F, in repair, 25mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F, in repair, Grating, square, 150mm size of PTMT (minimum weight 100gms) complete all as specified and directed.

Supply only PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, in repair, only PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 75mm bore PVC (SWR) branch piece, single (Single Y) equal or unequal with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) branch piece, single(Single Y) equal or unequal with access door complete all as specified and directed.

S&F, 110 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F, 75 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F, in repair, 75 mm outer dia PVC (SWR) floor trap, plain with Grating including joining with solvent complete all as specified and directed.

S&F, in repairs, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for Salt glazed stoneware (SGSW) drain pipes laid in trenches and jointed for 200mm bore internal dia of Grade 'A' pipe laid and jointed complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished and reforming benching as required for 200mm bore of pipe complete all as specified and directed.

S&F, in repairs, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, in repair, 8mm dia brass, chromium plated health faucet (Hand shower) with 01 meter long flexible tube and wall hook complete all as specified and directed. Make : Jaquar Cat No - ALD-573 or equivalent as approved by GE from the makes mentioned in Appx 'C'.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair, vitreous china wash basin, white, flat back of size 550mm x 400mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F, in repair, kitchen sink with out drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all bowl size 600mm x 600mm x 230mm to 260mm complete all as specified and directed.

S&F, in repair, 0.63mm thick, stainless steel plate rack of size 1200mm x 900mm x 180mm complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) including 'P' or "S" trap and including water closet seat cover complete all as specified and directed .

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of cement (unreinforced) of any description and in any position not otherwise specifically provided for such as sunken floor, roof padding etc complete all as specified and directed.

Demolition of cement (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete of chajjas and similar suspended work complete all as specified and directed.

Dismantling of timber scantling 40 sqmm and over in section, an any position (framded) complete all as specified and directed.

Dismantling of timber scantling but fillet rails, post rafter purlin etc under 40 sq cm in section (unframed) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of asbests cement (corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes of size 100mm jointed in neat cement mortar and taking out of trenches if required complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes of size 200mm jointed in neat cement mortar and taking out of trenches if required complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar for 110mm and 75mm bore of pipe from wall/floors etc complete all as specified and directed.

SNEH TRADERS

divyarsh entrprise

Ramdev and Sons

Shree Builders

Priya Construction co.

Navkar Enterprises