SPL REPAIR TO BLDG NO 22 BCD 47M QTRS FOR NURSES AND RETAINING WALL AT PALAMPUR MIL STN

Amount

SCHEDULE 'A' Part-I Excavation in trenches,nexc 1.50m wide and n exc 1.50m in depth for foundation,etc or for shafts,wells,cesspits,manholes,pier holes,etc n exc 10 sq m on plan and n exc 1.5m in depth and getting out any type of soil complete all as specified and directed.

Returning,filling in, including spreading, levelling, watering and well ramming in layers not exc25 cm any type of soil complete all as specified and directed.

Removing excavated soil n exc.50m and depositing where directed at aleveln exc 1.50m above the sterting point complete all as specified and directed.

Excavation post holes (or similar holes) in any type of soil each n exc 0.50 cu.m,getting out,returning,filling on and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25cm, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm crushed stone aggregate) as in cement concrete in foundation, filling and mass concrete complete all as specified and directed.

M&L plain cement concrete,1:3:6 type C-2 (using 20mm graded crushed stone aggregates) as in surface channels or drains etc, complete all as specified and directed.

M&L for thick PCC 1:4:8 type D-2 (40mm graded crushed stone aggregate) as in sub base of floors/ paver block/ path etc finishing the surface even & rough without using extra cement complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L PCC M-10 type B-1 (using 20mm crushed stone aggregate) as in surface channels or drains complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in support on walls, beams, columns in floors, roof landings, balconies, kitchen slab and in shelves a like complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

M&L walling of random rubble, un-courses, with best quality locally available harder stones such as granite, trap, basalt stone etc, well bonded bedded & solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 13 above but except stone. Note: Old stone obtained against dismantling/demolition shall be used.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, caltilevers, shelves including supports, overhangs etc also splays between floors and beams etc, fair finished surface complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 5 mm dia and over up to 10 mm dia in stirrups,spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F steel work in tubular trusses incl special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240 complete all as specified and directed.

S&F steel window 1.25 thick box type (Primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises guaged/glazed skelton shutter ERW sec 50mm x 20mm and 1mm thick with one or two openable leaf as directed consisting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled section portion in PCC (1:2:4) type B-1 four Nos for each window including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape-04 Nos per window. (ii) Handle of Z sec 20mm x 25mm, 100mm long- 1 No Per Leaf. (iii) MS tower bolt 150m long- 2 No per leaf. (iv) Z Sec 20mm x 25mm, 100mm long stopper-1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge-01 No per leaf. (vi) MS pintal hinges of size 75mm x 12mm - 2 Nos per leaf. (vii) Fabrication & fixing arrangement as per drg No. CEPZ TD-26/13 incl two coats of synthetic enamel paint over a coat of red oxide primer including taking down old existing unserviceable window with frame and shutter and grills complete all as specified and directed.

S&F factory made Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood rail and style plain framed, panelled shutter with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 (part 1) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer, complete all as specified and directed.

S&F pressed steel frames of size 165mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer,complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, incl glazing (sheet glass 3mm thick ordinary quality fixed with glazing putty in each pane etc.) with two coats of synthetic enamel paint over a cost of red oxide primer over new steel surfaces, complete all as specified and directed.

S&F mild steel roof trusses (framed), trussed, purlins, crane gantries. rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe 410-W (Grade E-250) complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sink) forming holes, without any attachment complete all as specified and directed.

S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. Fe-410 W(Gde-E-250) quality-B, complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE)

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

S&F GI frame work for ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section(not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including 4mm thick non AC board with two coats of white wash complete all as specified and directed.

S&F GI frame work for ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section(not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including 6mm thick E-board (Classic) false ceiling boarding complete all as specified and directed.

S&F aluminium anodised powder coated chowkhats frames for doors, windows, ventilators, partition with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F Powder coated Anodised aluminium window and ventilator shutters (minmium thickness of powder coating 50 micron), weight of aluminium section not less than 0.914 kg/m for style and rail, weight of glazing clip not less than 0.124 Kg/m including necessary joining cleats, glazing clips, rubber neoprane packing,anodised aluminium snap beading,screws,anodised aluminium fittings such as peg stays one number,hinges type B-21, 100 mm long two numbers,suitable handle one number on each shutter complete all as specified and directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 250 mm size (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp and staple ,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repair aluminium (extruded section body) door closer hydraulically regulated, designation No. 3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs PVC coated mild steel conduit pipe 25mm dia (Drapery rod) with PVC coated MS clamps to hold drapary rod and decorative attachment at one or both ends of drapary rod, fixed to opening of door/windows, each opening n exc 1.50 mtr, contained with a pair of clamps and ap pair of side ornamental attachments complete all as specified & directed.

S&F precoated sheet type door spring, heavy type, 200mm long including roller and roller plate complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/450mm x 350mm x 7mm/450x300x7mm/600x300x7mm thick set and jointed in neat cement slurry, pointed in white or coloured cement to match the colour of tiles, over and including 10mm thick backing coat in CM 1:4 to receive tiles, complete all as specified and directed.

M&L machine cut kota stone slab flooring 18 to 20mm thick laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 15 mm thick screed in CM (1:4) complete all as specified and directed.

M&L machine cut kota stone slab 18 to 20mm thick in riser of steps,skirting,dado and pillar laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Vitrified Ceramic tiles 10mm thick (square / rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified.

M&L Vitrified Ceramic tiles 10mm thick, light grade (square / rectangular) polished on vertical surfaces such as skirtings, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L 20mm thick granite (of any type) work (table rubbed and polished and moulding of outer edgers) for wall lining (veneering to wall) with and including 10mm thick in cement mortar (1:3) and pointed in white cement (1:2) using marble dust with admixture of pigments to match with shade of granite, complete all as specified and directed.

M&L 30cm x 30 cm x 25mm thick, coloured rubber moulded chequered cement concrete tiles with grey cement and pigment set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished and moulding of outer edges) in steps, jambs and pillars, window cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Precast cement concrete copings for fixing RCC jallie 50mm thick including all mouldings of type B-0 (1:2:4) using 12.5mm crushed stone aggregates, set in cement mortar 1:4 complete all as specified and directed.

M&L PCC M-10, nominal mix type C-1, using 20mm graded mechanically crushes stone aggregate, 50mm thick of in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternative panels n exc 1.20 Sqm each, 12mm wide and 5cm deep joints & shall be formed between the bays and shall be filled with mastic filling comprising a mixture of the part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume) complete all as specified and directed. Note:- The unit included for use of form work (straight or curved)

M&L 75mm thick PCC 1:2:4 type B-1 (using 20mm crushed stone aggregate) finished even and smooth without using extran cement, spike rolling to surfaces or making impressions of expanded metal, whilst the concrete in green complete all as specified and directed.

Glass dividing strip, 3mm thick 38mm wide fixed in any position complete all as specified and directed.

M&L 25mm thick PCC 1:2:4, type B-0 (using 12.5mm crushed stone aggregate) as in floor finished rough to receive floor finishes complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

Providing precast cement concrete louvres and jallies, 35mm thick including all mouldings of type B-0 (1:2:4) using 12.50mm crushed stone aggregate, set in cement mortar 1:4 complete all as specified and directed.

Demolition of PCC in ground floor and paving not exc 15cm thickness (below or above ground level) complete all as specified and directed.

Taking down roof trusses,coupled rafters or trussed beams clear span above 4.00m and upto 8m complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work precast concrete articles complete all as specified and directed.

Raking out joints/pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs etc. complete all as specified and directed.

Taking down cement plaster on walls and roof ceilings etc., including racking out joints, hacking for key, scrubbing down with water etc. to receive new plaster complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc. 1.5 sq.m each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) exc 1.5 sq.m but n. exc 4 sq.m each, complete all as specified and directed.

Dismantling water tanks and removing to store of capacity 500 ltr and not exc 1000 ltr and S&F rotational moulded polyethylene water storage tank 500 litres but not exc 1000 ltr capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, making connections including 20mm bore ball valve brass with polyethylene float and fly nut and dismantling existing water tank of any capacity and removing from site complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge and thickness in roof covering including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed.

M&L preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L preparing new surface of steel of any description, over 10cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long , fixed to wall with CP brass screw and PVC rawl plugs, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site complete all as specified and directed.

S&F steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specifed.

S&F steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specifed.

Fixing only old steel water tubing obtained from taking down, 15mm bore, galvanised, "medium grade" with all new fittings, fixed to wall and ceiling or laid in floor, complete all as specifed and directed.

Fixing only old steel water tubing obtained from taking down, 20mm bore, galvanised, "medium grade" with all new fittings, fixed to wall and ceiling or laid in floor, complete all as specifed and directed.

Vitreous china, wash hand basin, (white) of size 550mm x 400mm including brass CP waste coupling 32mm size with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends, complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed.

S&F 15mm bore fancy type stop valves/angle cock (two way if required), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union complete all as specified and directed.

S&F fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F soap dish vitreous china white,approximate size 160mm x 160mm x 90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm incl waste fittings, brass, chromium plated for sinks, with long screwed shanks and fly-nuts, waste pipe of specified bore and length, fixed in repair complete all as specified and directed.

S&F 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for GI tubing complete all as specified and directed.

M&L 15mm thick rendering over brick/stone masonry surface in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering over brick/stone masonry surface in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L raised pointing to squared rubble, coursed or uncoursed or ashlar masonry or concrete block walling in CM 1:4 complete all as specified and directed.

M&L concrete bed to drain pipes 100/110mm including packing under and completely surrounding pipes with concrete after they are laid and tested; in cement concrete 1:3:6 complete all as specified and directed.

S&F 100/110 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed .

S&F 110mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall, ceiling, floors etc. complete all as specified and directed.

S&F 100/110mm bore PVC (SWR) bends complete all as specified and directed.

S&F PVC (SWR) vent cowl 100/100 bore dia, complete all as specified and directed.

Drilling holes for bolts, pipes etc. exc 25mm dia but not exc 60mm dia, 10cm depth or above complete all as specified and directed.

M&L preparation of newly plastered surface of walls and applying two coats of oil bound distemper to achieve smooth surface complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of brick/stone masonry surface and applying two coats of cement base paint complete all as specified and directed.

Taking down shutter of any description exc 1 sq.m but n. exc 2 sq.m each. complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and paving's not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed.

Dismantling of wall & ceiling boards (fiber, pulp, insulation etc) or insulation boards /slabs /blankets any thickness, including cover fillets complete all as specified and directed.

Dismantling timber scantlings 40Sq.cm and over in section, in any position complete all as specified and directed.

Dismantling unframed work in fillets, rails, posts, rafters, purlins, scantling etc. under 40 sqcm in section complete all as specified and directed.

Taking down water tank exc 250 ltrs & not exc 500 ltrs capacity and removing to store complete all as specified and directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GI nipple for inlet, outlet, washout and overflow etc, including 20mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repair vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), complete all as specified and directed.

M&L 10 litres capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32mm dia PVC flushing pipe and 15mm dia, 450mm long PVC connection with CP brass coupling nuts and PVC washer at both ends complete all as specified and directed.

S&F vitreous china, wash basin flat back, with pedestal white of size 550mm x 400mm including brass Chromium Plated waste coupling 32mm size with long screwed shank and fly nuts, flange end bedded in red lead cement,PVC medium grade 32mm size waste pipe, PVC connection 15mm size, 450mm long with PTMT nuts at both ends (fixed in repair), complete all as specified and directed.

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 Kgf/sq.cm for low level cistern and waste pipe for sink, washbasin complete all as specified and directe

S&F in repairs fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repairs stop cock, fancy type, chromium plated, with long shank and cup cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repairs stop cock, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed to WHB and sink or concealed type wall mixer fixed in any position as per site requirement complete all as specified and directed.

S&F PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and directed.

S&F ball brass valves, high pressure, with polythene float and fly nut complete, screwed for 20 mm bore iron pipe or brass ferrule complete all as specified & directed.

M&L 32/40mm bore waste fittings, brass, chromium platged for glazed ware sinks, basin, etc. with long screwed shanks and fly-nuts, flange and bedded in red lead cement and other end fixed complete all as specified and directed.

Dismantling of cast iron or reinforced cement concrete, PVC drain pipes, fixed to wall or laid in trenches complete all as specified and directed.

S&F in repairs 110mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall, ceiling, floors etc. complete all as specified and directed.

S&F in repairs 110mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, as in floor and trenches complete all as specified and directed.

S&F in repairs 75mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall, ceiling, floors etc. complete all as specified and directed.

S&F in repairs 75mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, as in floor and trenches complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap plain with grating including jointing with solvent 75mm bore complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends complete all as specified and directed.

S&F in repairs,Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified & directed.

S&F steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, but except GI tubing complete all as specifed.

S&F steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, but except GI tubing complete all as specifed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares exc. 0.50 sq.m in each pane, complete all as specified and directed.

M&L preparation of newly/old plastered wall surface and applying two coats of oil bound distemper on newly plastered surfaces applying plaster of paris putty of 1mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of cement base paint complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.(inner girth only measured)

Cutting opening through walls built in cement mortar for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and directed.

SCHEDULE 'A' PART-II Taking down old unsv copper/aluminium point wiring concealed/batten (light, fan socket on power) complete, including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron, round block etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down un-serviceable DB of any size and capacity including MCB etc and removing material to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

Taking down unserviceable sub main wiring of any type and any size from wall, ceiling etc complete all as specified and directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5/6 amp switch with 1.5 Sqmm single core multistranded copper conductor FRLSH, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLSH, PVC insulated (unsheathed) drawn into and PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl all fittings such as Tee, connector pieces, L-junction etc on joints including (GI Modular metal flush boxes of any way including Modular white cover plate with frame i.e. 1 to 8 way as per site requirement) for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following:- (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed.

All as per the description of serial item No 142 here-in-before but one 5 pin socket outlet, 5/6 amps on the same board complete all as specified and directed.

All as per the description of serial item No 142 here-in-before but one 5 pin socket outlet, 5/6 amps, independent complete all as specified and directed.

All as per the description of serial item No 04 here-in-before but for one 5 pin socket outlet 15/16 Amps on Independent board with cables 2.5 sqmm size complete all as specified and directed.

S&F switch piano, flush type single pole one way 6 Amp, 240 volts ISI marked complete all as specified and as directed.

S&F socket outlet 2 in 1, 3 pin, 6 A complete all as specified and directed.

S&F socket outlet 3 pin, 6/16 Amp, flush type, 240 Volts, 6 pin flush type complete ISI marked complete all as specified and directed.

S&F switch piano, flush type single pole, one way 16 Amps, 240 volts ISI marked complete all as specified and directed.

S&F ceiling rose, 3 terminal surface type complete all as specified and directed.

S&F angle lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply & fixing surface /wall mounted light fitting pre wired suitable for single T8 LED tube along with supply and fixing one number LED tube in polycarbonate housing of nominal wattage - 18 Watt, Lumen out put - 2100 Lm, Colour Temp - 6500 Kelvin, Size & Length - G13/ T8/ 4 Feet with integral/in built driver, having short circuit and surge protection including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Make:- Cat Part No for batten:- STREAKT8UPTO 1X22WSSBSWH of make Havells 'or' IGP161LT8-16 of make Crompton 'or' TMC501 P 1xT-LED 22W P3241 of make Philips or its equivalent as approved. Cat Part No for Tubelight:- PHOTANULTRAE2.0 1213T8SSTL18WLED865SPC of make Havells 'or' LTT8-20 of make Crompton 'or' MAS LED tube 1200MM 18W865 T8 I-2100 lm of make Philips or its equivalent as approved

Taking down old un-serviceable light fitings/bulkhead fittings of any type and model complete and making good the disturbed surface complete all as specified.

M&L distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F of SPN 40 to 63 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connecting to GI earth wire of size 4mm size by means of bolts, nuts, check nuts and protected by provision of GI medium grade pipe of 15mm bore including provision of 40mm tk cover of RCC (1:2:4) reinforced with XPM (wt no less than 4Kg/sqm) and frame of angle iron 40mmx40mmx6mm with 6mm dia MS bar handle made to shape, GI light grade 20mm dia pipe for watering of suitable length placed on tp edge of earth plate, common salt and charcoal filling, with fixing arrangement, funnel, wire mesh and excavation and earthwork in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m complete all as per plate No. 3 of SSR 2009 Part-I and connecting to earth test point all as specified and directed by Engineer-in-Charge and including testing on completion.

Note:-(i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B1, 80mm thick reinforcement with 8mm TOR steel @ 100 c/c in lieu of CI cover and the rate includes in the unit rate of item. (ii) Earth electrode shall be protected upto test point using necessary arrangement with suitable size GI pipe up to 7.50m and the rate includes in the unit rate of item. (iii) Earth pit chamber and RCC cover shall be painted with red paint over a primer coat and the rate includese in the unit rate of item. (iv) The earth chamber shall be constructed 5m away from the edge of the bldg pit and the cost of the same is deemed to be included in the rate for this item.

Taking down old unserviceable electric storage water heater any type/size, supply and installlation of electric storage water heater (vertical type geyser minimum 5 Star rating) 50 ltr capacity, 240V, AC single phase having stainless steel inner tank incl heavy duty pin type fasteners 4" long and PVC flexible connection as per site requirement incl plug in top 15 amp and making necessary inlet/outlet water connection and making good disturbed surface of walls to match with existing surface complete all as specified and directed. Note:- Old unserviceable electic water heater to be deposited in MES store yard.

Taking down old unserviceable exhaust fan (PVC body) any type/size, supply and fix exhaust fan ISI marked, AC single phase 240V, made of steel body, voltage 230V, 50 Hz, RPM 1400, copper winding of sweep 250mm complete with connection from ceiling rose to exhaust fan complete all as specified and directed. Note:- Old unserviceable exhaust fan to be deposited in MES store yard.

S&F bell, AC 230 volts, single pole complete all as specified and directed.

S&F modular switch 1 way 6 A,1 module, 240 volts ISI marked complete all as specified and directed.

S&F modular bell push 6A 1 module complete all as specified and directed.

S&F modular socket outlet 2 in 1, 3 pin, 6 A complete all as specified and directed.

S&F modular socket 3 pin, 16 amp flush type, 240 volts ISI marked complete all as specified and directed.

S&F single pole and neutral enclosure with 1 two pin and earth plug and a socket complete with one single pole MCB, 20 amp, 240 volts ISI marked complete all as specified and directed.

S&F Sheet metal enclousers, TPN distribution board 4 way, double door complete with appropriate size bus bar, neutral link and Earth Bar fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

S&F SPN 32 to 40 Amp rating 240V, 10 KA 'C' curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioining complete all as specified and directed.

M&L in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sq mm for phase and neutral and one run of 6.0 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and directed. Note:- Wiring shall be done in proper colour coding.

S&F exhaust fan ISI marked, AC single phase 240V, made of heavy duty steel body, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 250mm complete with connection from ceiling rose to exhaust fan complete all as specified and directed. Note: Old unserviceable exhaust fan to be deposited in MES yard.

Supply, fixing, installation and testing vertical type storage electric water heater (Geyser) of 25 Ltrs capacity 230 volts including 5 star BEE rating, tank made of ultra thick super cold rolled steel plates with high density PUF insulation, 2 KW, 230 V, Single Phase, 50 Hz, AC, BEE 5 Star rated, suitable for a pressure rating of 0.8 MPa Bar with 7 years warranty on inner tank, 5 years on heating element & 2 year comprehensive warranty with & including connected accessories and 2 Nos anchor fasteners of size as per manufacturer instructions grouting and fixing and making good the disturbed surface complete and connecting electrical and water supply connection using steel braided hose 2 Nos complete all as specified and as directed. Make:- Havells, Model - Monza DX, Cat No: GHWAMGTWH025/Bajaj Calenta 25 Ltr or equivalent in Racold/CG. Note:- (i) Installed Geyser's warranty card should be submitted to the Engr-in-Charge. (ii)The cost of making good the disturbed surfaces and matching to the existing/original surface is deemed to be included in the unit quoted rates.

Taking down fan, sealing cable end, dismantling blades and removing fan and blade to store complete all as specified and directed.

S&F ceiling fan ISI marked, AC single phase 240V, complete with blades, down rods, electronic regulator and accessories, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 1200mm min air delovery 210 CFM 5 star rated with brushless direct current motor complete with connection from ceiling rose to exhaust fan complete all as specified and directed. Note: Old unserviceable exhaust fan to be deposited in MES yard.

Disconnecting water heater and taking in safe custody/refixing the same and making the connection and testing complete all as specified and directed.

Disconnecting electonic meters temper proof LCD display and taking in safe custody and refixing the same with caliberation and cleaning and making the connection and testing complete all as specified and directed.

SUBASH MAHAJAN

Kulbir Singh Govt. Contractor

M/S ER CONSTRUCTIONS

M/s ASS Construction Co

MM Constructions