Repair and Interior Furnishing work under the Expansion /Renovation/ Repair of Circuit House Champawat.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering All work upto plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-lll) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.ThermoMechanically Treated bars of grade Fe-500D or more

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana I Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate I retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work upto plinth level - Concrete of M25 grade with minimum cement content of 330 kg /cum

All work above plinth level upto floor V level - Concrete of M25 grade with minimum cement content of 330 kg /cum

Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brickwork with common burnt clay FPS (non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand)

Half Brick Masonry with common burnt FPS (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters ,window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sum.

Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Architect.Granite work.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing Ist quality ceramic glazed wall tiles conforming to1S: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Wall tiles for toilets Tile size:(150/200 x 150/200mm). Specification as per annexure 1

Providing and laying slate/quartzite tiles in flooring and skirting of approved colour and sizes (thickness upto 20mm), laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including epoxy grouting of joints

Providing and laying polished granite stone flooring in required design and patterns, in linear as well as curviliner portion of the building all complete as per the architectural drawings with 18mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement :4 course sand) laid and joined with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge Polished granite stone slab of all colour and texture except black, cherry/ruby red

Extra for pre finished nosing to treads of steps of marble stone.

Extra for granite stone flooring in treads of steps and risers using single length up to 2.00 metre .

LIME STONE FLOORING with 15-20 mm limestone stone, as per sample approved by Engineer-in-charge, over 20 mm (average) thick base of mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with epoxy coating and epoxy grouting.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with: Markrana white second quality

25 mm wooden planking, tounge and grooved in flooring, including fixing with iron screws complete with:Second class deodar wood

Providing and fixing on roof shingles composed of asphalt and combined with Glass felt and surfaced with mineral granules Certainteed, Algae Resistant, 110km/h Wind Resistance , Fiber Glass Composition: UL Class A Fire Resistance Rating( 1 Bag- 33.32 sft) including providing and Applying One coat of asphalt primer & anticorrosive fasteners, Swift Start - starter strip at Eave end,accessory – Shadow Ridge with matching features and colour over 12mm thick cement fibre board including waterproofing membrane a lightweight, synthetic polymer-based underlayment that outperforms felt and outclasses other synthetics. Designed for use on roof decks as a water-resistant layer beneath asphalt roofing shingles.The work includes with necessary Staging ,scaffolding and work to be Completed as per the engineer incharge. Surface area shall be considered for Measurement.complete in all manner as per manufacturer specification attached in annexure and approval of engineer in charge

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Gutter (600 mm over all girth)

Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183, density 48 kg/m? 50 mm thick, wrapped in 200G virgin Polythene bags placed over existing false ceilng and held in position by criss-crossing Gl wire.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre,with 25mm long dry wall screws @ 230 mm interval, including providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling work over the rabbit wire mesh reinforceent fixed to the framework all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting

Providing and fixing Teak wood panel of 12 to 15mm in thickness in false ceiling as per design and specs including polishing with pu polish to achieve satin finish, also including the as per design. Finishing: PU (matt) paint finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat. specifications provided in Annexure 1

Providing and fixing in place with necessary tools, nails, fastner, adhesive etc. Decorative teak wood mouldings 65mm x35mm as per design in ceiling and walls, including cornice and mouldings made of solid teakwood as per deisgn Finishing: PU (matt) paint finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement : 4 coarse sand)

12 mm cement plaster of mix :1:6 (1 Cement : 6 Fine sand)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 Itr/10 sqm over and including one coat of Special primer applied @ 0.75 Itr 10 sqm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Providing wooden panelling work on building façade with 18-20 mm teakwood panels, fixed over a framework of pinewood battens of size 50mm x 18 mm including all necessary fittings to complete the work as per design and instruction of engineer in charge Finishing: PU (matt) polish finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat

Providing and panelling on interior walls with teakwood panels of thickness 15-18mm as per design on a base frame work of pine wood battens of size 50mm x 25mm including all necessary hardware and adhesives, complete in all manner as per instruction of engineer in charge and drawings. Finishing: PU (matt) polish finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat

Providing and fixing wooden railing made of teak wood inclusive balustrade, jalis and rails as per design of heigth 900mm. As per design and instructions of engineer in charge, specification attached in annexure 1

Providing and fixing cnc cut wooden jali as per design made in teakwood panel. Specification attached in annexure 1

Stone work (machine cut edges) for wall cladding upto 3 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : with stone from local quarry upto 60mm thick having exposed face finely dressed and rough backing

Providing, hoisting and fixing Wooden truss made of sal wood as per design fixed in place with necessary stainless steel hardware, screws nails etc. complete in all manner as per instrtruction of engineer incharge Finishing: PU (matt) paint finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat

Providing and fixing teak wood panels of thickness 12-15 mm in sofit of roof overhang as per design and instruction of engineer in charge Finishing: PU (matt) paint finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat

Providing and panelling HDHMR panel of 4mm over 12mm HDHMR base board, including all adhesive, nail etc complete with Finishing: PU (matt) paint finish with pressureized pump spray of specified color, as per manufacturer application guideline, (2 coats of surfacer, 2 coat of pu white sealer, and 1 coat of top coat.) including dent filling,sanding and rubbing after every coat as required . Each coat to cover 8 - 9 sq.mtrs./ltr/coat

Providing and Displaying Marigold(Tagetes) inca hybrid different colour having 30 cm and above ht., with 6 to 8 flowers in bloom & blooming condition, well developed pot should be fully covered with fresh and healthy, foliage and flowers in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Tulip Dutch hybrid variety (3 in one) in each pot in full bloom fresh & bright in different colour well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Sunflower hybrid well developed 15 to 20 cm ht. with fresh & healthy foliage at blooming stage in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Cineraria Hybrid dwarf variety in different colour well developed with fresh & healthy foliage in bloom in 25 cm Earthen Pot/Plastic Pot.

Cosmos well developed fresh & healthy 20 to 25 cm ht. attractive colours multi branching at blooming stage in 20 cm Earthen Pot/Plastic Pot.

Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot

Neelgiri grass turf with earth 50mm To 60mm thickness

Bermuda Grass or Doob Grass

Acacia auriculiformis ht 150-165 cm in bag size 25 cm

Cassia fistula (Amaltash) height 120-135 cm. in big poly bag size 25 cm

Grevillea Robusta (Silver Oak) height 150-165 cm. in big poly bag size 25 cm

Excavation in foundation for retaining, breastwallsetc, inall typesof soil sand rocks includingall lead, lift anddisposal of surplusmaterial asper directionof engineer- in charge,asperdrawingandtechnicalspecificationsClause305.1of MORD Specifiction

WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 405.By mannual means

Providing and laying grey granite Cobble Stone of sizees 100-150x100-150x50-75 mm over 40 mm base of cement mortar (1:6), joints no more than 15mm wide filled with liquid grout composed of 3 part sand(2 part sharp sand, 1 part stone dust) and 1 part cement.

Providing and laying Natural stone blocks of variying sizes and thickness 40mm-60mm thickness in the pathways including levellingand base prepration with 50mm layer of sand with 50-100 m gaps in between each block filled with pebble stone of 25-30 mm size

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.(Note: Butt hinges and necessary screws shall be paid separately)Second class teak wood35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Second class teak wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with 1SI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class teak wood 35 mm thick

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250 x 10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc.

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

20 mm dia. nominal bore

25 mm dia. nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality complete High or low pressure with plastic floats 20 mm nominal bore

Providing and fixing brass stop cock of approved quality 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mmwith 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shades with 6 mm thick hard board backing: of Rectangular shape 453x357 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

75 mm dia

110 mm dia

Providing and fixing PVC Coupler (75 mm dia)

Providing and fixing PVC Coupler (110 mm dia)

Providing and fixing PVC Shoe (Plain) (75 mm dia)

Providing and fixing PVC Shoe (Plain) (110 mm dia)

Providing and fixing PVC plain bend of required degree. ( 75 mm dia)

Providing and fixing PVC plain bend of required degree. ( 110 mm dia)

Providing and fixing PVC Single tee with door required degree access door 75x75x75x110mm

Providing and fixing PVC Single tee with door required degree access door 110x110x100x110mm

Providing and fixing on wall face unplasticised Rigid PVC pipes (75 mm dia)

Providing and fixing on wall face unplasticised Rigid PVC pipes (110mm dia)

Providing and fixing on wall face unplasticised Rigid PVCpipes (110mm dia) For External Work

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour 20mm nominal bore. Weighing not less than 40gms.

Provinding & Fixing White Vitreous China Urinal including all materials T & P etc. Complete.Urinal (Make Jaguar or equivalent)

Providing and fixing white European wall hung water closet PP soft close seat cover, Hinges, Fixing Accessories and Accessories set, including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing 75 mm Pvc trap approved as per E/I (Make Jaguar or equivalent)

Providing and fixing 110 mm Pvc trap approved as per E/I (Make Jaguar or equivalent)

Provinding & Fixing Bib Cock with wall flange including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Provinding & Fixing long nose bib cock with wall flange including all materials T & P etc. Complete. approved as per E/I (Make Jaguar or equivalent)

Provinding & Fixing Piller cock including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing & Fixing shower Diverter as per specification (Make jaguar or equivalent)

Providing and fixing Sink Mixer with Swinging Spout (Wall Mounted Model) With Connecting Legs & Wall Flanges with including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing & Fixing Premium quality Bottle trap internal portion 32mm, size 250mm long wall connection pipe & wall flange as per approved by Engineer in Charge.

Provinding & Fixing Anguler Cock with wall flange including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Provinding & Fixing White Vitreous China Under Counter basin with including all materials T & P etc. Complete Counter top basin including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing C.P. brass shower rose with size 120 mm dia including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing C.P. brass shower Arm with size 20 mm & 450 mm long round Shape single flow with self cleaning function approved as per E/I (Make Jaguar or equivalent)

Providing and fixing Urinal Spreader bowl Top Inlet 15mm with Fixing Stud Brass Ingots as per IS:1264-1997 Brass Rod as per IS:319-1989 Plating: Nickel-10.0 micron Chromium-0.3 micron Stainless Steel Finish

Providing and fixing 600mm long towel rail without hanger total length of 600mm, including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing towel ring round with Round Flangincluding all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing toilet paper holder including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing tile inser floor trap of size 150 x 150 mm

Providing and fixing Soap dispenser including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

Providing and fixing Glass Self including all materials T & P etc. Complete approved as per E/I (Make Jaguar or equivalent)

King Size Bed specification as per Annexture 1 atteched

Super King Size Bed specification as per Annexture 1 atteched

Single Size Bed specification as per Annexture 1 atteched

Bed Side Table (night stand) specification as per Annexture 1 atteched

Wardrobe specification as per Annexture 1 atteched

Reception Desk specification as per Annexture 1 atteched

L-Shaped Table CM specification as per Annexture 1 atteched

Office Chair (Visitor chair) specification as per Annexture 1 atteched

CM Office Chair specification as per Annexture 1 atteched

L-Shaped Table specification as per Annexture 1 atteched

Sofa Side Table Circular (coffee table) specification as per Annexture 1 atteched

Coffee Table (centre table) specification as per Annexture 1 atteched

Sofa 4 seater (3 SEATER) specification as per Annexture 1 atteched

Sofa 2 Seater specification as per Annexture 1 atteched

Sofa single Seater specification as per Annexture 1 atteched

Relaxing Sofa Chair (wing chair) specification as per Annexture 1 atteched

Dining Table with 14 chairs specification as per Annexture 1 atteched

Dining Table WITH 6 CHAIR specification as per Annexture 1 atteched

Study Table specification as per Annexture 1 atteched

Room Chair (study chair) specification as per Annexture 1 atteched

Conference Table specification as per Annexture 1 atteched

Janta Darbar Table specification as per Annexture 1 atteched

Janta Darbar Chair specification as per Annexture 1 atteched

Supplying of King Size Bed Matress of The Sleep Company or equivalent of size 2130X1980 mm and 250 mm with air channels and 3 zone adaptive support approved as per the direction of engineer in charge or equivalent.

Supplying of King Size Bed Matress of The Sleep Company or equivalent of size 1800 X1800 mm and 250 mm with air channels and 3 zone adaptive support approved as per the direction of engineer in charge or equivalent.

Supplying of King Size Bed Matress of The Sleep Company or equivalent of size 1800 X900 mm and 150 mm with air channels and 3 zone adaptive support approved as per the direction of engineer in charge or equivalent.

Storage cabinet as per design 1800 x 450 x 750 made in teak wood finish pu polished to match colour and texture of other woodwork finishes provided in the room. As per design instruction of engineer in charge specification as per Annexture 1 atteched

Manufacturing & supplying of Curtains Channel, as per shape and design as per the following and as per drawing,,all complete job as per approved designed drawings & directions of engineer in charge. specification as per Annexture 1 atteched

Supplying and fixing of Main Curtains with liner backing and shear curtain having standard width 54" approx. including cost of stitching accessaries like rings,SS hooks as required as site, shape and design all complete job as per approved specificatons.specification as per Annexture 1 atteched

Television 65" specification as per Annexture 1 atteched

Mahesh Verma Constructions (BID ID -405910)