Construction of State Level Laboratory at Sidhpur in Tehsil Dharampur District Mandi HP

Amount

Civil Work:- Excavtion in foundation, trenches etc. in all kinds of soil such as pick work jumper work, blasting work in soft/hard rock, chiselling in soft/hard rock including wedging out upto all lift, stacking the excavated soil upto all lead clear from the edge of excavation and then returning the stacked soil in 15cm layers when requaired into plinths, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Providing and laying cement conrete 1 : 4 :8 . ( 1 cement : 4 sand and : 8 grade stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth upto all leads and lifts as per the direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying cement concrete (M25 design mix)1 : 1½ : 3 mix. ( 1 cement : 1½ : sand : 3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in :

Foundation, footing, basis of columns and the like mass concrete.as per direction and to the entire satisfaction of Engineer-in-Charge.

Columns,pillars,posts & struts upto floor two level.

Beams, cantilever, girder and lintel sides and soffits of beams haunchings cantilevers girder, bressumers and lintel not exceeding one meter in depth in all heights from floor as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor two level. as per direction and to the entire satisfaction of Engineer-in-Charge.

Stair cases (except spiral stair cases) excluding landing nut including preparing of the surface and finishing of nosing upto floor two level.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain.

Foundation, footing, basis of columns and the like mass concrete.as per direction and to the entire satisfaction of Engineer-in-Charge.

Columns,pillars,posts & struts upto floor two level.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors upto 200mm kin thickness.

Beams, cantilever, girder and lintel sides and soffits of beams haunchings cantilevers girder, bressumers and lintel not exceeding one meter in depth in all heights from floor as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Providing form work of ordinary timber plankings so as to give a rough finsih including centring, shuttering, strutting and propping etc. heightof propping and centring below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu reinforced concrete and plain concrete and plain concrete work in:-

Stair cases with sloping otstepped soffits excluding landing

Edges of slabs and breaks in floors & walls under 20 cms. Wide.

Providing, Laying of Tor steel reinforcement for RCC work including bending binding and placing in position including wire upto all floor level as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work using common burnt clay Ist class building bricks in super structure above plinth level upto floor two level in cement mortar 1:6 (1 cement :6 sand)including curing complete as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.

Square rubble masonery with approved quality i/c racing out joints in wall in CM 1:4 (1cement:4 Sand)

Half brick masonry in common burnt clay 2nd class building bricks in superstructure above plinth level upto floor two level incement mortar 1:4 )1 cement :4 sand )including curing complete as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position with second class deodar wood in all leads and lifts.

Providing and fixing wood paneled glazed or paneled and glazed shutters for doors, windows and clear story 40mm thick windows including bright finished black enameled iron with necessary screws with second class deodar wood 40mm thick in all leads and lifts.

Prov. & fixing wire gauge shutters using galvanized MS wire gauge of IS gauge designation 85 G. with wire of dia. 0.56 mm for doors,windows & clerestrey windows including bright finished black enameled iron hinges with necessary screws.

15mm cement plaster in single coat of rough sides of bricks/concrete stone walls for interior plastering upto floor two level including arrises internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement:6sand) within all leads and lifts.

20mm cement plaster in single coat of rough sides of bricks/concrete stone walls for interior plastering upto floor two level including arrises internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement:6sand) within all leads and lifts.

Boulder/stone filling under flooe/behind retaining walls.

Providing and laying cement concrete 1:6:12 (1 cement :6 sand :12 graded stone agg. 40mm nominal size) On curing complete excluding cost of form work in foundation and plinth in all lead and lifts as per direction and to the entire satisfaction of the Engineer-in-Charge.

Providing fixing Vetrified double charge 60x60 cm (Nitco/Kajaria/RAK/EQU flooring as required complete.

P/F 10mm thick Anti skid floor tile in Toilet floor

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry.

Providing and laying Duro stone vetrified tiles (300x300mmx10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.

Providing and laying granite stone in flooring 20mm(average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick

Providing and fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete)

Providing and fixing 19mm thick Commercial Board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete)

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete.

Providing and fixing 4mm thick burl ply of standard quality and of approved shade & design wall lining i/c fixing with approved adhesive, butt jointing and nails & screws complete (Base frame work to be measured & paid for separately)

Providing and fixing bright finished brass sliding door-bolts with nuts and screws etc. complete.

Providing 40x3mm iron hold fast 40mm cms long including fixing to frames with 10mm dia bolts, nuts and wooden plug and embedding in cc block 30x10x15 cms 1:3:6 (1 Cement:3 sand : draded stone aggregate 20mm nominal size) in all leads and lifts.)

Providing & fixing Moulded hand rail of M.S. hollow pipe 50mm dia welded in straignt length over M.S. flat Hollow hand rail in stair case

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete.

Providing and fixing bright finished hard drawn hooks and eyes.

Providing & fixing 12mm thick & 100mm tvide palment with 25mm dia meter wooden curtain rod and bracket including fixing 25x3mm MS flat 10 cm long

Making plinth protection 50mm thick in cement concrete 1:3:6 (1 cement :3 sand :6 graded stone aggregate 20mm nominal size as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.

Constructing course rubble hammer dressed "U" shap open surface drain with side wall 15x22 cm in cement motor 1:6 (1 Cement :6 sand) and in side plastering with cement plaster 1:3 (1 cement :3 sand ) including earth work and laying 10cm cement concrete in 1:5:10 (1 cement :5 sand :10 graded stone agg. 40mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement :2 Sand :4 graded stone 20mm nominal size) and finished with a floating coat of neat cement complete as standred design as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.

Providing & fixing 15cm wide 45 cm overall semi circular plain G.I. sheet gutter with iron brackets 40x3m size bolts and nuts 0.80mm thick sheet

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a requred for metling the surface.

Applying priming coat over new wood and wood based surface after and I/c preparing the surface by thoroughly cleaning oil, grease,dirt and other foreign matter with ready mixed paint other than white as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lift.

Painting two coat (excluding Priming coat )on new wood and wood based surface with ready mixed paint brushing to give an even shade I/c cleaning of all dirt dust and other foreign matter, sand papering and stopping with while enamel paint as per direction and to the entire satisfaciton of Engineer-in-charge upto all lead and lifts.

Providing & fixing PVC rain water pipe 100mm dia

Steel work welded in builtup section trusses & framed work including cutting ,hosting and fixing in position and applying a priming coat of red lead paint. In Beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

Steel work rivetted in built up sections including cutting,hoisting, fixing,in position and applying a priming coat of red lead paint .In grating,Framed s,bars,ledders railings,brackets & similar works.

Providing prepainted G.I. Sheet roofing fixed with galvanised scruws hooks 0.63 cm thick sheet as per doirection and to the entire satisfaction of engineer in charge

Providing ridges or hips 63 cm over all in plain G.I.sheet with galvanised iron J or L hooks.bolts and nuts 8mm dia G.I. Limpetand bitumen washers copmlete:-0.63 mm thick sheet

Providing and laying interlocking paver block in grey cement and under layer of sand 0.125 mtr or 125 mm thick average complete in all respect as per direction and to the entire satisfaction of engineer in charge.

ELECTRICAL WIRING:- Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core(flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, mod

Group A.

Group C.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required.

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required:-

20mm dia

25mm dia

Supplying an drawing following sixe of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existin surface/recessed, Steel.PVC conduit as required.

PVC insulated HRFR LS Copper conductor 1.5 Sq.mm.

3x1.5 Sq. Mm.

3x4.0 Sq. mm.

Supplying abd erection of 6 amps. To 32 amps. Rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-

Single pole, Cat-A.

Supplying and fixing following ratring, double pole (sinle phase & neutral) 240 volts, residual current fircuit breaker (RCCA), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

25 Amps. Cat-A.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plates, cable, identification labels interconnectionss, phosphatized, and powder painted,including earthing etc. as required.

double door-6 way

Double door-8 way

Wiring for light/power plug with 2x10 Sqmm PVC insulated copper conductor single core cable in surface/rcessed steel conduit along with 1 No. 10 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit/sub-main 4x6 swmm size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) opper conductor cable in surface/recessed steel conduit along with 2 No. 6 sqmm.( 4x6+2x6) HRFRLS/PVC insulated single core copper conductorcable for earting as required.

S/F G.I. Modular Box:-

Supply and fixing G.I. Modular Box of following sizes along with modular base and cover plate for modular swiches in recessa as required.

Supplying & fixing following size modular base and cover plate on the existing modular metal boxes as requied:-

Modular base and cover plat, 2 module

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required.

Supplyin and fixing following rating Modular switch/socket in the existing switch box/cover plate including connection etc. as required.

Telephone socket outlet, Modular.

TV. Socket outlet, modular.

Supplying and drawing co-axial TV cable, RG-6 grade, 0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper brain and protected with PVC sheath in the existing surface/ recessed, stel/PVC conduit as required.

Supplyin and drawing following pair of Fire Retardant, PVC insulated 0.5 Sq. mm. (FR-Flexible) copper conductor, flat, u narmoured, telephone cable in existing surface/recessed, steel/PVC conduit as required.

Two pair

Supply and drawing following pair for internet in the existin surface/recessed, steel/PVC conduit as required.

Two pair

Earthing with copper earth plate 600 mmx600mmx3mm thick, includin accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or clke and salt) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode completle as required.

Supplying and laying 8 SWG Copper wire at 0.50 mtr. Below ground level for earth electrode conductor, including soldering etc. as required.

WATER SUPPLY AND SANITARY:- Providing and fixing white vitreous china was down water closet (European type W.C. pan) within tegral 'P' or 'S' trap including jointing the tap with soil pipe in CM 1:1 of yware/Hindware/CERA.(seat and cover to be measured and paid for seperately) but includng entirie carriage of mateials upto all leads and lifts.

Anglo India Universal Closet

Providing and fixing 10 liter capacity low level white PVC flushing eistern with manually controlled device (handle lever) conforming to IS: 7231,Parryware/Hindware/Seabrid/Orient (Coral) with all fittings and fixtures such as syphonic system, float valve etc. complete inclyding cutting and makng good the walls and floors whe rever required and entire carriage of material upto all leads and lifts.

Providing and fixing white plastic seat and cover (Solid Type) for Anglo Indial Universal closets with CP brass hinges and ruber buffers including entire carriage o material in all leads and lifts.

Providing & fixing vitreous china wash basin flat back size 550x450mm Hindustan sanitary ware /CERS of standard quality with single hole for pillar tap including cutting holes in walls and maing good the same but excluding fittings and including entire carrigate material upto all leads. lifts and heights.

Providing and fixing vistreous China pedastral for Wash Basin complete.

Providing & fixing 32mm dia chromium plated brass rubberplug for sink on wash basin including entire carriage of materials upto all leads, lifts and heights.

Providing &fixing 32mm PVC waste pipes (heavy duty) for wash basin or sink including brass check nut and including entire carriage of materials upto all leads, lifts and hiehgts.

Providing & fixing 100mm dia C.P. grating for floor trap.

Providing &fixing 600mmx450mm beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet and fixing to nylon plugs with steel screws and washers complete including entire carriage of materia lin all leads, lifts.

Providing & fixing 600x20mm Chromium plated brass towel rails of Jaguar Czar/ Mare makecomplete with chromium plated brass brackets fixed to rawl plugs with chromuym plated brass screws including entire carriage of materials upto all leads, lifts and heights.

Providing & fixing 600x20mm glasshelf with C.P. Brassbrackets complete.

Providing & fixing Toilet paper holder C.P. brass with caprtan bed of approved brand.

Providing & fixing CP Jet set i/c CP brass stop work complete in all respect.

Providing & fixing CP brass soap dish of Jaguar/Czar/Mare make with CP brass bracket fixed to rawl plugs with cP brass screws including entire carriage of materials upto all leads, lifts and heights.

Providing & fixing CP brass bib tap 20mm dia.

Providing & fixing 15mm dia C.P. brass pillar Tap.

Providing & fixing Brass Stop Cock 15mm dia.

Providing & fixing Brass stop cock 20mm dia

Providing & fixing CP stop cock 15mm dia.

Providing & fixing 15mm nominal bore and 45 cm in length PVC connection pipe (heavy duty) with brass unions including entire carriage of materials upto all leads and lifts.

Providing & fixing brass full way Valve wheel 15mm dia.

Providing & fixing brass ball valve (Horz Plunger Type) High pressure with polythene floats 15mm dia.

Providing & fixing 1000 lt.PVC water tank of Sintex or Equvalent made i/c accessories fitting complete.

Constructioning manhole with reinforced cement concrete top slab in 1:2:4 (one cement:twosand: four graded crushed stone aggregate 20mm (twenty millimeters) nominal size) foundation concrete 1:4:8 (one cement: four sand: eight graded crushed stone aggregate forty millimeters nominal size) inside plastering 15mm thick with cement mortar 1:3 (one cement : three sand) and makig channels in cement concrete 1:2:4 mix (one ceent:two sand: four graded crushed stone aggregate 20mm (twenty millimeters) nominal size) finished smooth complete including curing and testing and entire carriage of materials up to all leads ands lifts.

Inside size 800mm x800mmx 500 (eight hundred into five hundred millimeters) and 500mm (five hundred millimeters) deep including RCC frame and cover 505mm (five hundred five millimeters) internal dia meter (heavy duty) with 230mm thick (two hundred thirty millimeters) wall of common burnt clay brick masonry in cement mortar1:3 (one cement: three sand).

Providing & fixing Ferrule i/c boring & taping the main 15mm dia.

Providing & fixing to wall/ceiling and floor galvanized mild steel tubes (medium grade) of Jindal make, tube fitting and clamps including making good the wall, ceiling and floor including entire carriage of materials upto all leads and lifts.

15mm nominal bore.

20mm nominal bore.

Providing & fixing sand cast/cast iron spun spigot and socket soil waster and ventilating pipe of approved brand (lead caulked joints to be measured and paid for separately) including all leads and lifts of materials as per BIS specification.

100mm nominal bore.

75mm nominal bore.

Providing and fixing sand cast iron/cast iron spum fittings and accessories including entire carriage of materials upto all leads and lifts.

a)Bends of required degree, any radius.

I) Plain

i) 75mm nominal size

100mm nominal size.

B) Collar

i) 75 mm nominal size

ii) 100 mm nominal size

Providing & fixing cast iron cowl including entire carriage of materials upto all leads and lifts as per BIS specification.

Providing lead caulked joints to sand cast iron/ast pipes and fittings including testing of joints including entire carriage of materials upto all leads and lifts.

100mm dia meter

75mm dia meter

Providing & fixing MS stay and clamps fdor sand cast iron/C.I. pipes

100mm dia meter

75mm dia meter

Providing & fixing 75mm cast iron floor trap of self cleaning design with or without vent arm complete including cost of curring holes and making good the walls floors and entire carriage of materials upto all leads and lifts.

Provisions for survey investigation design & drawings after acertaining the safe bearing capacity of the soil at site. The structural design & drawings of all the buildings & other components and getting them approval from the competent authority

HARJEET SINGH

MS Kamal Dev Sharma