Construction of New Government Science Collage at Varachha, Dist.Surat.

Construction of New Government Science College at Varachha, Dist. Surat

BILL OF QUANTITIES

Percentage Rate Tender

Item Description of Item Quantity Unit Rate In Amount

1 Excavation for foundation upto 1.5 m depth including 7754.00 Cmt 123.13

sorting out and stacking of useful materials and

disposing off the excavated stuff upto All lead.(A) Loose

2 Excavation for foundation for depth from 1.5 m to 3.0 4860.00 Cmt 170.50

m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto

All lead. lead.(B) Dense or Hard soil

3 Excavation for foundation from depth 3.00 m to 5.00 m 3084.00 Cmt 184.77

including sorting out and stacking of the useful materials

and disposing off the excavated stuff up to all lead. (A)

Dense or Hard soil

4 Filling in foundation and plinth with sand in layers of 20 524.00 Cmt 481.80

cm. Thickness including watering ramming and

consolidating etc. comp.

5 Filling available excavated Earth (Excluding Rock) in 7785.00 Cmt 136.92

trench plinth side of foundation . in layer not excluding

20 cm in depth consolidation each deposited layer by

ramming and watering etc. complete

6 Filling foundation and plinth with murrum or selected 1557.40 Cmt 301.78

soil in layer of 20 cm in thickness including ramming

watering and consolidating etc. complete

7 Filling in foundation Coursed rubble Soiling with hard 882.00 Cmt 3476.26

stone of approved quality in foundations and plinth in

Cement Mortar 1:6 (1-Cement : 6-coarse sand) etc.

Item Description of Item Quantity Unit Rate In Amount

8 Anti Termite System 2592.00 Smt 134.33

P/L of Permenent piping technology Anti Termite

treatment before flooring work by installing LLDP (Low

linear density Polyethylene) tube of 8 mm O.D.& 6.4 mm

I.D.With in Built Pressure Compenstaion chif every 30 cm

interval in the tube, having working pressure of 2 kg/cm

2 and realese rate of 1.9 ltr/Hour fixed by P-Clip and

nails . The LLDP pipe shall be installed at the entire

periphery of the building and at internal network of

building depth of 20 to 200 mm under floor every 2 to

mtr.c/c distance (adjustble as per building layout ) &

Ends of loop pass through a PVC Elbow of minmum

mm ID at junction box of wall and floor level, entring into

a steel reinforcmed grooved flexible pipe mini.22 mm LD

leading into junction box and during injecting chemicls

for termite control tretment. The anti-termite chemical

Lmidcloprid 30.5% SC Mix as per IS 6313(part-III) shall

be injected by the pressure pump diluted with water @

10.5 ml/5ltr of water at the rate of 2 kg/sq,cm.@ 5 ltr

/Smt .the contractor shall submit approved line plan for

piping system and junction boxes dully approved By

Engineer -in-charge with bond of 5 Years warnty .

9 Providing and laying in position Ready Mixed M-150 2023.00 Cmt 4320.98

grade concrete for reinforced cement concrete work in

Foundations & Plinth, using cement content as per

approved Design Mix manufactured in fully automatic

batching plant established on site and transported to site

of work in transit mixer having continuous agitated

mixer, manufactured as per mix design of specified grade

for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, excluding

the cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) For All Floor

Item Description of Item Quantity Unit Rate In Amount

10 Providing and laying in position Ready Mixed M-200 384.00 Cmt 6037.38

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) For Plinth slab

and all R.C.C. memebers at all floor level

11 Providing and laying in position Ready Mixed M-250 4205.33 Cmt 5292.40

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Footing and

12 Providing and laying in position Ready Mixed M-250 549.51 Cmt 7715.39

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Column For

Item Description of Item Quantity Unit Rate In Amount

13 Providing and laying cement concrete 1:3:6 (1-Cement : 66.99 Cmt 3095.25

3- coarse sand : 6- machine cut stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

14 Providing and laying in position Ready Mixed M-250 281.36 Cmt 6373.10

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for

Plinth/Ground Beam

15 Providing and laying in position Ready Mixed M-250 1287.00 Cmt 6674.08

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Beam For All

Item Description of Item Quantity Unit Rate In Amount

16 Providing and laying in position Ready Mixed M-250 63.00 Cmt 6942.74

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Chhajja For

17 Providing and laying in position Ready Mixed M-250 43.50 Cmt 8004.25

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Lintal For All

18 Providing and laying in position Ready Mixed M-250 1333.00 Cmt 7464.91

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Slab For All

Item Description of Item Quantity Unit Rate In Amount

19 Providing and laying in position Ready Mixed M-250 87.50 Cmt 6797.30

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Stair For All

20 Providing and laying in position Ready Mixed M-250 1093.00 Cmt 7351.79

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for RCC Wall For

21 Providing and laying in position Ready Mixed M-250 43.55 Cmt 6880.12

grade concrete using cement content as per approved

Design Mix manufactured in fully automatic batching

plant established on site and transported to site of work

in transit mixer having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of reinforcement and including cost of centering.

shuttering, formwork finishing and admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer -In - Charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) for Coping For

Item Description of Item Quantity Unit Rate In Amount

22 Providing and fixing stainless steel railing made from 119.00 Rmt 3973.34

anticorrosive SS 304 grade pipes, consisting of 50 mm

dia (16 gauge) handrail and 38 mm dia (16 gauge) SS

grade balusters placed at 1.20 m centre-to-centre, firmly

fixed into the RCC slab. The railing shall include

horizontal SS pipes of 25 mm dia (16 gauge) spaced at

0.20 m centre-to-centre, fixed using 18.75 mm dia (16

gauge) SS pipe connectors with the balusters. The entire

assembly shall be provided with all necessary brackets,

base plates, welding, grinding, buffing, and mirror

polishing, complete with all accessories as per the

approved detailed drawings and as directed by the

Engineer-in-Charge. The rate shall be inclusive of all

materials, labour, fittings, fixing in position, finishing,

cutting, wastage, scaffolding, loading, unloading, and

transportation to site — complete in all respects.

23 Providing IS Mark TMT FE 550D bar reinforcement for 1072433.00 Kg 86.76

RCC work including bending & placing in position

complete up to All floor Level

24 Extra for concreting in grade M350 instead of M250 3417.00 Cmt 273.57

including cost of cement, labour etc. complete.

25 Extra for concreting in grade M300 instead of M250 120.00 Cmt 182.38

including cost of cement, labour etc. complete.

26 Providing and fixing eco-friendly light weight calcium 1014.00 Smt 1674.15

silicate false ceiling tiles having Tegular edge & 15 mm

Thick Densified edges on the Tile Periphery for Extra

Strength The Light weight calcium silicate ceiling tiles

shall have, light reflection 85% non-combustible as per

B.S. 476 part IV, 100% humidity resistance and also

having thermal conductivity0.043° w/m KC.for the best

thermal Insulation. The Light weight calcium Silicate tile

shall be of approved texture Fine fissured/ Spintone/

Cosmos having NRC value of 0.5 & Globe having NRC

value of 0.75 NRC or equivalent of size 595 X 595 mm to

be laid on true horizontal level suspended inter locking

metal grid of hot dipped galvanized steel sections

(galvanizing @120 grams per Smt including both side)

consisting of main ‘T’ runner suitably spaced at joints to

get required length and size of 24 X 38mm made from

0.30 mm thick (minimum) sheet, 1200mm centre to

centre, and cross ‘T’ of size 24 X 28mm made out of

0.33mm (Minimum) sheet spaced 1200mm along spaced

between main 'T' at 600mm centre to centre to form

agrid of 1200x600mm and size 24x48mm made of

0.30mm thick (Minimum) sheet to be interlocked at

middle of the 1200x600mm panel to form grid of size

600x600mm resting on periphery walls/partitions on a

perimeter wall angle pre-coated steel of size

(24x24x3000mm made of 0.40mm thick (minimum)

sheet with the help of rawl plugs at 450mm centre to

centre with 25mm long dry wall screws @ 230mm

interval and laying 15mm thick densified edges light

Item Description of Item Quantity Unit Rate In Amount

27 Brick work using common burnt clay building bricks 110.50 Cmt 4214.33

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement :

5 -fine sand)(B) Conventional below plinth

28 Brick work using common burnt clay building bricks 1543.66 Cmt 4503.04

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement :

5 -fine sand) (B) Conventional All Floor

29 Half Brick masonry in common brunt clay building bricks 1444.00 Smt 685.83

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional in super

structure. for All Floor

30 Providing 20 mm thick double coat mala cement plaster 15241.52 Smt 286.10

on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster in

cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2

(1 Cement : 2 Coarse sand) finished with trovel including

scaffolding curing etc. complete For All Floor

31 Providing 10 mm. Thick cement plaster in Single coat for 11087.97 Smt 189.50

plastering on ceiling and soffits of stairs and finished

even and smooth in : (I) Cement mortar 1:4 (1 cement :

sand) including Mala troveled finish etc. complete.For All

32 20 mm Thick Mala Plaster + Natural Stone Stamping 2629.00 Smt 1330.88

Texture Plaster :

Providing and applying 20 mm thick double coat cement

plaster in Cement Mortar consisting of 12 mm thick base

coat in C.M. 1:4 finished rough to receive key and 8 mm

thick top coat in C.M. 1:2 over external brick

masonry/R.C.C. surfaces, including forming grooves as

per drawings and instruction of Engineer in charge

Providing and applying 1.5 mm to 2.0 mm thick Natural

Stone Stamping Texture finish using Apex Ultima Allura

Concordia Granizia or approved equivalent over

prepared plastered surface, in approved shade and

pattern duly approved by the Architecture Office,

Gandhinagar, including surface preparation, exterior wall

primer, protective top coat of Apex Ultima Allura Clara

Matt/Sheen or approved equivalent, all materials, labour,

scaffolding, curing, tools & plants and incidental charges

complete as per manufacturer’s specifications and

directions of Government Architect, Gandhinagar /

Engineer-in-Charge.Including providing written 5 years

guarantee against peeling, flaking, blistering, fading, loss

of adhesion, fungal/algal growth and texture failure,

Item Description of Item Quantity Unit Rate In Amount

33 20 mm Thick Mala Plaster + Exposed RCC Stamping 2674.23 Smt 1418.37

Texture Plaster :

Providing and applying 20 mm thick double coat cement

plaster in Cement Mortar consisting of 12 mm thick base

coat in C.M. 1:4 finished rough to receive key and 8 mm

thick top coat in C.M. 1:2 over external brick

masonry/R.C.C. surfaces, including forming grooves,

bands and required architectural features, complete.

Providing and applying 1.5 mm to 2 mm thick Exposed

R.C.C. Stamping Texture finish using Asian Paints Archi

Concrete or approved equivalent over prepared

plastered surface, in approved shade and pattern duly

approved by the Architecture Office, Gandhinagar,

including surface cleaning and preparation free from

algae, fungus and seepage, application of exterior primer,

application of 1st and 2nd coats of texture paste in semi-

dry condition, making approved texture pattern with

required tools, gentle steel trowel buffing, and

application of two coats of protective clear finish as per

manufacturer’s specifications as per manufacturer’s

specifications and directions of Government Architect,

Gandhinagar / Engineer-in-Charge.Including providing

written 5 years guarantee against peeling, flaking,

blistering, fading, loss of adhesion, fungal/algal growth

and texture failure, complete.

34 Providing throating or plaster drip and moulding to 1619.50 Rmt 43.74

R.C.C. Chhajja.

35 Applying two coats of Birla or Asian acrylic lapy (putty) 25991.00 Smt 40.59

& two coats of primer of approved brand and

manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand

papered smooth.

36 Wall painting (two coats) with plastic emulsion paint of 14813.00 Smt 83.36

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

37 Wall painting (two coats) with plastic emulsion paint of 11179.00 Smt 89.04

approved brand and manufacture on undecorated ceiling

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

38 Wall Painting (Two coats) with weather proof 100 % 4001.00 Smt 120.26

acraylic emulsion (Apex or equivalent type) paint of

approved brand and manufacture and of required shade

on exterior wall surface to give an even shade over and

including primery coat with Alkaly resistance primer of

approved brand after thoroughly brushing surface to

remove all dust and remains of loose powdered material

etc. copm. for all height

Item Description of Item Quantity Unit Rate In Amount

39 Masonary work using Aerated light weight concrete 133.00 Cmt 4598.92

block having crushing strength not less than 35 kg/sqcm

for super structure above plinth level upto floor two level

in cement mortar 1:5 ( 1 cement : 5 fine sand ) complete

as per Technical Specification

40 Providing and fixing GI louvers as shown in elevation, 45.00 Sqmt 2392.00

using 114 mm wide G.I. sheet of 0.55 mm thickness

having weight not less than 490 gm per running meter,

roll formed to obtain 84 mm wide louvers, snap fixed on

specially shaped G.I. channels. The GI channels shall have

a weight not less than 3.06 kg per running meter. The

louvers and channels shall be factory finished with

minimum 55 micron thick powder coating of approved

colour and make. The work includes providing,

fabricating, fixing, necessary fasteners, supports, cutting,

fitting, and all complete as per drawings and as directed

by Engineer-in-charge, including provision of openable

Mechanisum etc. completed as per directed engineer

41 Providing and fixing in position standard extruded 31.00 Smt 3706.70

Aluminium Four Track Sliding Window System (27 mm

Series Deluxe Type) comprising four shutters and one

top fixed ventilation. The frame shall consist of top,

bottom, and side sections of size 136 mm × 50 mm,

mm thick, weighing 2.466 Kg/Rmt, and the shutters shall

consist of top, bottom, and side sections of size 65 mm ×

28 mm, 1.5 mm thick, weighing 1.020 Kg/Rmt, with

interlock section of size 37 mm × 31.75 mm, 1.3 mm

thick, weighing 0.328 Kg/Rmt. The window shutters

shall be fitted with 5 mm thick transparent tinted float

glass, while the fixed top ventilation portion shall be

glazed with 5 mm thick clear float glass, both fixed with

clip bead arrangement and EPDM rubber gasket to

ensure airtight and watertight performance. All joints

shall be properly sealed with approved section sealant,

and the entire system shall include air lock strip and

power-coated standard aluminium fittings. The work

shall be completed in all respects including materials,

labour, fittings, tools, and equipment, as per detailed

drawings and as directed by the Engineer-in-Charge.

Item Description of Item Quantity Unit Rate In Amount

42 Providing and fixing in position standard extruded 456.00 Smt 3759.22

Aluminium Three Track Sliding Window System (27 mm

Series Deluxe Type) comprising three shutters and one

top fixed ventilation. The frame shall consist of top,

bottom, and side sections of size 91 mm × 45 mm,

mm thick, weighing 1.591 Kg/Rmt, and the shutters shall

consist of top, bottom, and side sections of size 65 mm ×

28 mm, 1.5 mm thick, weighing 1.020 Kg/Rmt, with

interlock section of size 37 mm × 31.75 mm, 1.3 mm

thick, weighing 0.328 Kg/Rmt. The window shutters

shall be fitted with 5 mm thick transparent tinted float

glass, while the fixed top ventilation portion shall be

glazed with 5 mm thick clear float glass, both fixed with

clip bead arrangement and EPDM rubber gasket to

ensure airtight and watertight performance. All joints

shall be properly sealed with approved section sealant,

and the entire system shall include air lock strip and

power-coated standard aluminium fittings. The work

shall be completed in all respects including materials,

labour, fittings, tools, and equipment, as per detailed

drawings and as directed by the Engineer-in-Charge.

43 Providing and fixing in position standard extruded 106.50 Smt 3301.69

Aluminium Two Track Sliding Window System (27 mm

Series Deluxe Type) comprising two shutters and one top

fixed ventilation. The frame shall consist of top, bottom,

and side sections of size 54 mm × 45 mm, 1.5 mm thick,

weighing 0.993 Kg/Rmt, and the shutters shall consist of

top, bottom, and side sections of size 65 mm × 28 mm,

1.5 mm thick, weighing 1.020 Kg/Rmt, with interlock

section of size 37 mm × 31.75 mm, 1.3 mm thick,

weighing 0.328 Kg/Rmt. The window shutters shall be

fitted with 5 mm thick transparent tinted float glass,

while the fixed top ventilation portion shall be glazed

with 5 mm thick clear float glass, both fixed with clip

bead arrangement and EPDM rubber gasket to ensure

airtight and watertight performance. All joints shall be

properly sealed with approved section sealant, and the

entire system shall include air lock strip and power-

coated standard aluminium fittings. The work shall be

completed in all respects including materials, labour,

fittings, tools, and equipment, as per detailed drawings

and as directed by the Engineer-in-Charge.

Item Description of Item Quantity Unit Rate In Amount

44 Providing and fixing in position round-shaped 3.00 Smt 2921.93

aluminium window of 2.10 m diameter or specified

fabricated from standard extruded aluminium sections

(27 mm Series Deluxe Type) complete with curved frame

and shutter profiles, accurately bent and joined to form a

true circular shape. The central portion shall consist of a

rectangular two-track sliding window of size 1.20 m ×

0.90 m or specified, having frame sections of 54 mm ×

mm, 1.5 mm thick and shutter sections of 65 mm ×

mm, 1.5 mm thick, with interlock section 37 mm ×

mm, 1.3 mm thick. The sliding shutters shall be fitted

with 5 mm thick transparent tinted float glass fixed with

clip bead arrangement and EPDM rubber gasket to

ensure airtight and watertight performance. The circular

periphery shall be provided with fixed glazing using

mm thick clear float glass set in aluminium sections with

proper sealant, ensuring perfect finish and alignment. All

joints shall be sealed with approved weatherproof

sealant, and the system shall include air lock strip and

power-coated standard aluminium fittings. The work

shall be completed in all respects including materials,

labour, fittings, tools, and equipment, as per detailed

drawings and as directed by the Engineer-in-Charge.

45 Providing and fixing openable Aluminium casement 8.00 Smt 4583.58

window made from standard extruded colour anodized

Aluminium sections, with frame members (bottom, top

and sides) of Jindal Section No. 20630 and openable

shutters made of single-glass shutter members (top,

bottom and sides) of Jindal Section No. 20727, including

glazing clip member Jindal Section No. 19359. The

shutters shall be fitted with 5 mm thick transparent plain

float glass, fixed with EPDM rubber gaskets and

transparent silicon sealant. The work shall include

providing and fixing S.S. hinges, S.S. handle of 150 mm,

S.S. stopper 200 mm long, and all necessary fittings,

fixtures and accessories, complete as per approved

drawing and as directed by the Engineer-in-Charge.

46 Providing & Fixing in position standard extruded 17.50 Smt 2955.97

approved colour anodised Aluminum Ventilator with

outer frame 63.50 x 38.10 x 1.95 mm (of Jindal Section

No.4605,@ Wt 1.094 kg/Rmt ) with 3mm thick Bajari

figure adgesteble tinted louvers glass fixed to

alluminium strip blade including fixtures, fastenning,

labours and equipments as per detailed drawing as

directed. For Ventilators

Item Description of Item Quantity Unit Rate In Amount

47 Providing and fixing in position standard extruded 28.00 Smt 2739.32

approved colour anodised aluminium ventilator, having

outer frame of size 63.50 x 38.10 x 1.95 mm (Jindal

Section No. 4605, @ wt. 1.094 kg/Rmt), with 3 mm thick

Bajari figure tinted adjustable glass louvers on both sides

and 5 mm thick coloured tinted glass for fixed glazing at

the centre, fixed to aluminium strip blades with suitable

clips and accessories. The item includes all fixtures,

fasteners, cutting, fitting, alignment, sealing, labour,

tools, and equipment complete as per approved drawing,

specification, and as directed by the Engineer-in-Charge.

48 Providing and fixing double shutter specially designed 9.00 Smt 5405.52

hollow metal door comprising 35 x 100 mm M.S.

rectangular hollow section frame with 25 x 25 mm M.S.

pipe horizontal stiffeners placed at equal spacing

throughout the height for rigidity and stability. Both

shutters shall be fabricated with 19 mm thick Marine

Plywood, finished with approved shade, pattern, and

design of decorative laminate on both sides, and edge

beading neatly polished. The door shall be fitted with

durable floor spring (minimum capacity 200 kg) and

cm long stainless steel handles on both sides, including

all fixtures, fasteners, holdfasts, hinges, necessary

hardware fittings, polishing, finishing, labour, and

materials, complete as per architectural drawing and as

directed by the Engineer-in-Charge.

49 Providing and fixing 38 mm thick Double flush door 198.00 Smt 4262.20

shutter, solid core with Anodized Aluminium section

(jindal door section no 19552-weight not less than

kg/mt ) frame size 63.5mm x 38mm inserted Non teak

wood frame inside the aluminium section for durable

grip of hinges & Double shutter with required

teakwood batten having 1mm thick lamination on both

side, Durable Grip shall be providing with both side

15cm long stainless steel handle and necessary Locking

system of Godrej, ,S.S. fixtures & fastenings etc. directed

by engineer in charge.

50 Providing and fixing 38 mm thick single flush door 58.50 Smt 4016.77

shutter, solid core with Anodized Aluminium section

(jindal door section no 19552-weight not less than

kg/mt ) frame size 63.5mm x 38mm inserted Non teak

wood frame inside the aluminium section for durable

grip of hinges & single shutter with required teakwood

batten having 1mm thick lamination on both side,

Durable Grip shall be providing with both side 15cm long

stainless steel handle and necessary Locking system of

Godrej, S.S. fixtures & fastenings etc. directed by

engineer in charge.

Item Description of Item Quantity Unit Rate In Amount

51 Providing and fixing FRP frame size 100 x 50 mm and 35 67.50 Smt 2362.39

mm thick FRP depress panel single or Double shutter

having extra reinforcement on sides & edges in Gel coat

finish.The core of the both shutter & frame is to be filed

up with injected fire retradat grade polyurethene foam

done in situ along with embeded wooden pieces for

stiffening & also taking hinges & fintures.The whole FRP

frame & single or double shutter is to be waterproof,

weatherproof ,termite proof & resistance to mild

acid/alkali.Rates are to be inclusive of S.S hinges with

necessary screws & alluminum fixtures & fastenings &

fartener sleeve.Colour and Shade approved by Engineer-

52 Providing and laying integral cement-based 1735.00 Smt 1568.03

waterproofing treatment on horizontal surface below

ground level for underground structures, including

surface preparation and complete system as directed by

the Engineer-in-charge, consisting of: (i) first layer of

22–25 mm thick approved rough Kota stone slab laid

over 25 mm thick cement mortar 1:3 (1 cement :

coarse sand) mixed with waterproofing compound

conforming to IS:2645 in recommended proportion over

prepared leveling course (paid separately), including

sealing of joints and grouting with cement slurry mixed

with waterproofing compound; (ii) second layer of

mm thick cement mortar 1:3 mixed with waterproofing

compound; (iii) finishing the top with 10–12 mm

nominal size stone aggregate @ approx. 0.008 Cmt per

Smt, well spread and embedded in the second layer,

complete in all respects including curing, as directed.

53 Providing and placing 0.6m x0.6m GVT Vitrified Tile 602.50 Smt 1294.82

vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

new surface or fixing on existing flooring by adhesive

material including dismentaling of existing flooring and

jointed with color cement slurry including finished with

flush pointing & cleaning the surface etc. complete in

Two colour pattern and 3mm groove including material

cost as per directed engineer incharge.(tack 10% DARK

54 Providing and placing 0.6m x0.6m GVT Vitrified 8 mm 29.00 Smt 1301.89

thick tile skirting over 12 mm (average) base of cement

mortar 1:3 ( 1 cement: 3 coarse sand) on new surface or

fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete in Two colour pattern

and 3mm groove including material cost as per directed

engineer incharge.(tack 10% DARK shade)

Item Description of Item Quantity Unit Rate In Amount

55 Providing and placing 0.6m x0.6m GVT Matt Vitrified Tile 366.00 Smt 1308.96

vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

new surface or fixing on existing flooring by adhesive

material including dismentaling of existing flooring and

jointed with color cement slurry including finished with

flush pointing & cleaning the surface etc. complete in

Two colour pattern and 3mm groove including material

cost as per directed engineer incharge.(tack 10% DARK

56 P & L 60 x 45 cm Machine cut Machine Polished Blue 4931.00 Smt 1019.39

Kota Stone slab flooring over 20 mm (average)thick

base of cement mortar 1:6 (1-cement 6-coarse sand) or

L.M 1:1.5 (1 Lime putty : 1.5 coarse sand laid over and

jointed with grey cement slurry mixed with pigment to

match the shade of slab including rubbing and polishing

etc.complete (A) 30mm thick

57 P & L 60 x 45 cm Machine cut Machine Polished Blue 633.00 Smt 1130.79

Kota Stone slab 30 mm thick in riser of steps,skirting

dedo and pillars laid on 10 mm thick cement mortar 1:3

(1-cement 3-coarse sand) and jointed with grey cement

slurry mixed with pigment to match the shade of slab

including rubbing and polishing etc.complete (30 mm

58 Providing and laying antiskid ceramic tiles 30 x 30 cm 338.00 Smt 960.42

size 6 mm thick in flooring treads of steps and landing

laid on a bed of 12 mm thick cement mortar 1:3 (1-

cement:3-coarse sand)finishing with flush pointing in

white cement as per directed engineer incharge.

59 Providing and laying coloured glazed tiles of the size 300 1009.50 Smt 1513.28

mm x 600 mm x 8 mm in skirting, risers of steps and

dedo on 10 mm. thick cement plaster 1:3 (1 cement :

coarse sand) & jointed with white cement slurry as per

directed engineer incharge.

60 Providing and laying machine-cut, free-edge, machine- 694.50 Smt 3136.05

polished granite stone (18 mm thick) for finished treads

and risers, including 1 cm projected nosing with rounded

moulding in treads, laid over 12 mm average thick

cement mortar 1:6 (1 cement : 6 coarse sand) for treads

and 10 mm average thick cement mortar 1:3 (1 cement :

3 coarse sand) for risers; jointed with grey or coloured

cement slurry, including rubbing, polishing, and making

three grooves of size 3 mm × 3 mm along the length of

each tread, complete in all respects.

Item Description of Item Quantity Unit Rate In Amount

61 Providing and laying China mosaic type waterproofing 2705.50 Smt 1107.97

treatment on terrace including cleaning the surface by

wire brush as directed, including applying neat cement

slurry @ 2.75 Kg/Sq.mtr. mixed with waterproofing

compound after cleaning the surface, laying cement

concrete using brickbats (size 25 mm to 100 mm, well

immersed in water before use) with 50% of cement

mortar 1:5 (1 cement : 5 coarse sand) mixed with

waterproofing compound over 20 mm thick layers of

cement mortar 1:5 (1 cement : 5 sand) to required slope,

including rounding of junctions of walls and slabs and

after two days of proper curing, applying second coat of

cement slurry, finishing the surface with 20 mm thick

cement mortar 1:4 and fixing China mosaic tiles (broken

glazed tiles of approved colour and shade, laid in proper

slope and pattern), finally finishing the surface with

white cement slurry, and after finishing the whole

terrace shall be flooded with water for a period of two

weeks for testing the waterproofing efficiency, all work

shall be carried out as per the direction of the Engineer-

62 Providing and laying waterproofing treatment by 405.00 Smt 1003.96

conventional method including cleaning the slab surface

by wire brush as directed, including providing first layer

of cement mortar 1:4 of 40 mm thickness mixed with

waterproofing compound at the rate prescribed by

manufacturer, including putting of brick bats (average

thickness 40 mm, well immersed in water and laid

uniformly) on first layer of mortar, including applying

cement slurry @ rate of 0.08 bag/Smt on fixed layer of

brick bats, including maintaining necessary slope, in

second layer 40 mm thick cement mortar 1:4 mixed with

waterproofing compound as directed, including finishing

smooth with cement slurry as directed complete, all

work shall be carried out as per the direction of the

Engineer-in-Charge.

63 Providing Plinth Protection to Building including 307.00 Smt 1607.42

excavation in ordinary soil and laying cement concrete

1:3:6 using stone aggregates of 40mm nominal size in

foundation layer 100 mm thick below pre-cast Rubber

Dye inter locking concrete block 60mm thick with grade

of concrete M200 pneumatic compressed by

mechanically pressed and as per approved design

including 75mm Sand layer for levelling and filling the

joint with sand in proper line and level etc. complete,

Including Providing and fixing pre-cast concrete kerb

stone of grey cement based concrete block 30cm length,

30cm height and 15cm thick of M250 grade concrete as

per approved design and including excavation for fixing

in proper line and level, filling the joint with C:M 1:3

(1cement:3 fine sand) etc. complete.

Item Description of Item Quantity Unit Rate In Amount

64 Providing and fixing mirror polished 16–18 mm thick 360.00 Smt 2610.85

Granite stone of approved quality in cladding on sill and

around doors/windows/ventilators, with chamfered

edge moulding and polished finishing on exposed edges,

fixed over 12 mm thick cement mortar (1:3) and set with

cement slurry and adhesive, complete as directed by

Engineer-in-charge.etc. complete.

65 Providing and fixing safety grills of required pattern for 16198.00 Kg 112.14

windows/doors using 16 mm dia M.S. bars placed

horizontally at 100 mm c/c and Vertically at 250 mm c/c

16 mm dia M.S. bars, fixed with necessary M.S. flats / M.S.

angle as required, including cutting, welding, fabrication,

grinding and finishing, complete in all respect. The work

includes one coat of approved steel primer and two coats

of synthetic enamel paint of approved shade and make,

as per drawings and as directed by Engineer-in-charge.

66 Providing erecting and fixing double coated Syntex PVC. 20000.00 Liter 3.95

(ISI) water tank of required capacity each with all

necessary fittings and connection etc. complete on

67 Providing laying and jointing in true line and level 50mm 300.00 Rmt 195.67

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX

or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

68 Providing laying and jointing in true line and level 40mm 230.00 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX

or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

69 Providing laying and jointing in true line and level 25mm 430.00 Rmt 91.84

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX

or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Item Description of Item Quantity Unit Rate In Amount

70 Providing laying and jointing in true line and level 15mm 400.00 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX

or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

71 Providing, laying and jointing in true line and level 160 100.00 Rmt 834.38

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 210 mm length x 196 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all

72 Providing laying (to level or slopes) and jointing 1108.00 Rmt 678.02

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with collars

and butt ends prepared for collar joints including testing

of joints complete.(D)

73 Providing, laying and jointing in true line and level 110 775.70 Rmt 878.57

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all

74 Providing and fixing concealed center point to wall 50.00 Rmt 660.58

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. [E] 50mm.

75 Providing and fixing concealed center point to wall 50.00 Rmt 447.72

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. [F] 40mm.

Item Description of Item Quantity Unit Rate In Amount

76 Providing and fixing concealed center point to wall 150.00 Rmt 253.82

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. [C] 25mm.

77 Providing and fixing concealed center point to wall 150.00 Rmt 170.36

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. [A] 15mm.

78 Providing, laying and jointing in true line and level 75 90.00 Rmt 292.90

mm dia. UPVC SWRType B pipe conforming to IS 13592-

1992 with one end plain and other end socketed with

rubbering and fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp at every

mm c/c or shall be conceled in walss as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

79 Providing and fixing in PVC SWR cowel went 75mm dia 6.00 No 15.66

to pipes.(B) 75mm dia.

80 Providing and fixing in PVC SWR cowel went 110mm dia 14.00 No 28.79

to pipes.(B) 110mm dia.

81 Providing and fixing PVC SWR Nahni trap IS 14735 for 82.00 No 599.64

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread

down or hinged grating including the cost of cutting and

making good the walls.

82 Providing and fixing wash down water closet (European 24.00 No 3003.74

type W C pan) with integral P and S trap including

jointing the trap with soil pipe in cement mortar 1:1 (1

cement five sand) including providing and fixing plastic

seat cover for wash down WC with CP brass hinges and

rubber buffers back plastic seat and including providing

and fixing PVC flushing tank with a pair of C I or MS

bracket with complete fitting such as lead valve siphon

15 mm dia brass ball valve with polythene float CP brass

handle unions and couplings for connection with inlet

out let and over flow pipes 40 mm dia porcelain

enameled flush bend including cutting holes in walls and

making good the same connection the flush bend with

cistern and closet vitreous china.

83 Providing and fixing brass screw down Angle Valve 15 82.00 No 555.50

mm dia of approved make, heavy duty, with necessary

brass fittings, PTMT washers, and connections, fixed in

position with all labour, tools, and materials, tested for

proper operation and water tightness, complete as

Item Description of Item Quantity Unit Rate In Amount

84 Providing and fixing PVC stop cock 40 mm dia, heavy 18.00 No 757.50

duty, suitable for water supply lines, including necessary

PVC fittings, solvent cement, Teflon tape, and labour

charges for proper fixing in position, tested for water

tightness and smooth operation, complete as directed.

85 Providing and fixing ball cock of approved. quality as 4.00 No 189.84

directed.(A) Copper Metal (ii) 50mm dia.

86 Providing and fixing washbasin with single hole for pillar 9.00 No 1697.13

tap with C.I. or M.S. brackets painted white including

Rubber plug, sutting holes and making good the same but

excluding fittings and also including rate of C.P. brass

waste for washbasin or sink (A) 32mm dia. and M.I.

fisher union for washbasin or sink. (A) 32mm dia.; (A)

Vitreous China:(ii) Flat Back washbasin 550 mm x v

400mm size. (i) In white colour.

87 Providing and fixing 600mm x 450mm bevelled edge 21.00 No 859.41

mirrror of superior glass mounted on 6mm thick A.C.

sheet or plywood sheet and fixing to wooden pluge with

C.P. brass screws and washers.

88 Providing and fixing C.P. brass towel rail comlete with 20.00 No 616.42

C.P. brass brackets fixed to wooden plugs with C.P. brass

scews (B) 600mm x 20mm size.

89 Providing and fixing screw down bib taps of following 75.00 No 214.81

size.(A) Brass screw down bib tap polished bright. (i)

90 Providing and fixing pillar tap, capstan head, screw down 26.00 No 308.73

high pressure with screws, shanks and back nuts. (i)

91 Providing and fixing in position 300 mm high, 150 mm 75.00 No 308.73

wide English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

92 Providing and fixing Urinal of approved quality including 18.00 No 1640.22

connection with trap and with integral longitudinal flush

pipe.(A) Squating plate pattern white earthenware

93 Providing and fixing chromium plated brass half trun 53.00 No 263.77

flush cock of approved quality including fixing in pipe

line etc. complete (ii) 25mm dia.

94 Providing and fixing S.W. gully trap with C.I. grating brick 6.00 No 1246.92

masonry chamber and water tight C.I. cover with frame

of 300mm x 300mm size (inside) with standard weight

(i) Square mouth traps (B) 150mm x 100mm size P or R

95 Constructing brick masonry chamber for underground 30.00 No 2288.66

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal dimensions

with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Item Description of Item Quantity Unit Rate In Amount

96 Constructing brick masonry chamber for underground 30.00 No 2495.71

C.I. Inspection C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg.

Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm

intenal dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete (i) Inside dimensions

500mmx 700mm and 450mm deep for single pipe line.

97 Extra over items for every additional depth of 0.1M. of 20.00 No 242.39

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 455mm x 610mm size.

98 Extra over items for every additional depth of 0.1M. of 20.00 No 264.86

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 500mm x 700mm size.

99 Providing cement vata (10cm x 10cm size) quarter round 317.00 Rmt 24.28

in cement mortar 1:1 including neat cement finishing

watering etc. Complete

100 Providing and fixing MS Ladder of required pattern with 600.00 Kg 119.18

MS flats(30x3mm) or round or square bars (12mm) at

required spacing & with round headed bolts and nuts or

screws or welding including primer coat of approved

quality and two coats of oil paintas as directed by

engineer in charge

101 Providing and fixing in position 150 mm high, English 100.00 No 404.00

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools &

plants etc. complete.

102 Providing and fixing 16–18 mm thick machine-cut, 20.00 Smt 3858.20

mirror polished granite partitions of approved colour

and quality between urinals, with neatly chamfered and

moulded edges on all exposed faces. The granite shall be

fixed true to line and level using cement slurry mixed

with approved polymer-based adhesive, over properly

prepared surface. The work includes cutting to required

size, edge polishing, providing necessary

grooves/rebates if required, backing support, and sealing

joints with approved non-staining epoxy/silicone

sealant, complete. The item also includes curing,

protection, cleaning, and finishing, all as per drawings

and as directed by the Engineer-in-charge.

103 Constructing kitchen Platform of 16mm to 18 mm thick 14.00 Smt 4192.51

Polished Granite at top and 25 mm thick Kota stone slab

one side polished at bottom with cementing Materials /

adhsives including makeing necessary grooves in walls

with Vertical sandwich two Kotastone 25 mm support

every 60 cm centre to centre or as required including all

labour material of approved quality incl. full moulded

round front edge granite strip of one side polished and

jointed with grey cement slurry including rubbing and

polishing etc. complete for all floors

Item Description of Item Quantity Unit Rate In Amount

104 Providing and fixing 15 mm to 18 mm thick granite 26.00 Smt 3210.79

shelves of approved quality, fixed over an average 12 mm

thick base of cement mortar 1:3 (1 cement : 3 coarse

sand) along with approved adhesive. All exposed edges

shall be chamfered as directed by the Engineer-in-

charge. Work includes cutting to size, fixing in proper

alignment, jointing, curing, and finishing complete. This

includes cupboard shelves, kitchen, bathroom, and

storage units as required.

105 Providing and fixing aluminium anodized structural 115.00 Smt 8304.73

glazing work at any height with approved anodized

aluminium sections of size 101.60 mm × 57.00 mm ×

2.00 mm (Jindal Section No. 22713, wt. 2.187 Kg/Rmt),

fixed with 53 mm × 2.00 mm pressure plate (Jindal

Section No. 22711, wt. 0.434 Kg/Rmt) and 57 mm ×

mm cover plate (Jindal Section No. 22711, wt.

Kg/Rmt), including necessary cleats, brackets and

fasteners. The glazing shall be with 8 mm thick heat-

strengthened reflective glass panels, fixed with structural

silicone sealant (Dow Corning Grade 995 and 789 GP)

and backer rod/pressure tape of appropriate size

depending upon the joint gap. The work shall also

include provision of side-hung openable window

shutters within the system as per drawing, fixing with

high-quality expansion bolts having adequate load-

bearing capacity, including all necessary fittings,

fastenings, scaffolding, labour, tools, equipment, and

materials, complete in all respects as per detailed

drawings and as directed by the Architect/Engineer-in-

106 Providing and fixing Kitchen sink with C.I. or M.S. 2.00 No 3640.04

brackets, painted white including cutting holes in walls

and making good the same but excluding fittings. (C)

Vitreous China Sink.(i) 600mm x 450mm x 150mm size

107 Providing and fixing kitchen platform trolley having 14.00 Smt 12442.19

three drawers of SS (IS 304) of required size like thali,

katleri, perforated, partition, cupsosar type in kitchen

platform having drawer front side and backside by using

19mm thick all proof plywood of ISI quality all side

laminated etc. as directed. The size of SS (IS 304) basket

of size 4" to 18" for thali, dish, katleri, perforated,

partition, cupsosar type as directed including necessary

S.S. fittings, handles, nobs, telescopic channels, etc. as

Item Description of Item Quantity Unit Rate In Amount

108 Providing and fixing 0.75 meter wide sand which type 304.00 Smt 5953.95

counter platform including supplying and fixing granite

stone of Z black or equivalant quality 18 mm thick

mirror polished on top and side posiition and vertical

strip at front with cement slurry & adhesive including

moulding of both exposed edges over 25 mm thick

kotah stone platform fixing in top and sides and

itermediates supports fixing with cement mortar and

adhesive and finishing all material and labour and

assessories and 3 no flat back wash with necessary fitting

109 Steel work, welded in built up sections framed work 21404.00 Kg 91.08

including cutting, hoisting, fixing in position and applying

a priming coat of read lead paint & two coat oil paint.

(A)In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross

beams. Hip and jack rafters, purlins conneted to common

rafters and the like.

110 Providing and Fixing 6 mm thick Lexan Polycarbonate 15.00 Smt 1441.90

multi wall roofing sheet fixed with hilti screw and rubber

silicon sealer and alluminium strip of size 50 x 3 mm etc

complete as directed by Engineer in charge.

111 Extra for additional height of propping and centering 626.00 Smt 607.99

where the height of propping and centering exceeds 4 .O

M between supporting floor to ceiling including

temporary brick or stone pillars for supporting as

required. (i)Height more than 6.0 M.and upto 7.0 M.

112 Providing and laying in position REBAR as specified in 30.00 NO 116.15

true line & level including drilling adequate hole,

cleaning the same, grouting with HILTI, HY - 200mm

rebar system as per manufacturers specifications strictly

in accordance with structural details having minimum

depth of embedment 125mm, etc complete For all floors

(a) 10 to 12 mm dia.

113 Providing and Fixing a set of wall mounted 38 mm dia U 6.00 NO 2671.45

shaped horizontal stainless steel collapsible grab bar

38mm vertical stainless steel fixed grab rail of grade SS

304 from round pipe supported and 75 mm dia 8 mm

thick SS 304 base flange on wall including anchor

fasteners, nuts, accessories as per detailed drawing etc.

complete as directed by Architect or Engineer in charge.

114 Providing and fixing MS Z clamp on Wall or celling for 690.00 NO 85.85

Pipe Fitting including all type necessary fittings and

accessory etc. completed as per directed engineer in

115 Providing and fixing coloured self adhesive PU-Tactile 106.50 Smt 4586.41

tile, ground surface indicators of Polyurethane) of size

300mm x 300mm for guiding/warning to the visually

visitors in the centre/side of the pedestrian/approach

pathway as per specification and guidelines complete in

all respect to the entire satisfaction of in charge.

Item Description of Item Quantity Unit Rate In Amount

116 Providing and placing braile indicator of size 170 mm x 32.00 Rmt 820.12

35mm for handrails of the approved design and make

have braile dots raised 0.5 mm above base plate to be

installed at specific locations as per direction of engineer

117 Providing and fixing of conspectus tape 50mm width on 780.00 Rmt 99.99

of treads in staircase including cutting pasting etc. As per

harmonised guidelines complete in all respect to the

entire satisfaction of engineer in charge.

118 Providing and Fixing 15 mm thick 300 mm x 300 mm 30.00 Smt 1205.94

Tactile Warning Tiles (Attention Tiles i.e. Tactile

Warning Surface Indicator {TWSI}) of Johnsan Endura

Tac Button Yellow Plus or equvqlent make in flooring

laid on 20 mm thick cement mortar 1:6 (1 cement :

coarse sand) on new surface and jointed with cement

slurry including finished with flush pointing & cleaning

the surface for all floors as per detailed drawing etc.

complete as directed by Architect or Engineer in charge.

Thse tiles shall be Anti Skid, Chemical Resistant, Fade

Proof, Frost - Heat & Weather Proof, High Flexural

Strength, Highly Durable, Stain Resistance . All Tactile

Warning Tiles meet the specific size and dimension

standards as required by ISO/FDIS

119 Providing and fixing Expansion joint following items 396.50 Smt 8972.34

(a) expansion joint 100 mm thick expansion joint board

of best quality and approved make including cutting to

required size and shape at all levels .

(b) the expansion joint by 600 polymer or equivalent

confirm to BS 4254-1983 as per required shade and

manufactured specification by making groove of 50 mm x

12.5 mm lather by cutting or by repairing groove and

removing mortar drop or any other foreign materials

including applying primer and filling required size

(oversize of joint PU foam).

(C) Applying and providing Expansion joint sealing

System on 100 mm vide joint including cleaning of

exansion joint by mechanical means provision of

adhesive and flexible membrane with required bond

length as per menufracturer specification and 4mm thick

alluminium strip covering with one side sloted and

bolted with suitable system, inclusive of all manpower,

machinery and material as per specification and as

(d)fixing 25 cm Wide & 3mm thick exterior composite

panel on existing expansion joint horizontally &

vertically with all material, hardware, acessories &

fittings etc completed.

all items above a to b carry out as per directed engineer

Item Description of Item Quantity Unit Rate In Amount

120 Providing and Fixing Size: L 75mm x W 75mm x H 1200 ; 200.00 No 598.93

15 mm thick U shape corner Rubber Reflective Guards

with yellow reflective Patti fixing on RCC/brick surface

Including all fitting and material charges & it shall be

Chemical Resistant, Fade Proof, Frost - Heat & Weather

Proof, High Flexural Strength, Highly Durable, Stain

Resistance as per detailed drawing etc. complete as

directed by Architect or Engineer in charge.

121 Providing and fixing Precast Fibre Reinforced Perforated 333.50 No 1007.98

Concrete Cover of size 600x450 mm and 75mm thick to

be fixed on existing Brick Masonary Trench with cement

mortar 1:3 finished smooth with a floating coat of neat

cement etc. complete.

122 Providing and fixing modular plastic (PVC/HDPE) speed 200.00 Rmt 1614.99

breaker on existing RCC road, made of high-impact UV-

stabilized material with anti-skid surface and inbuilt

reflectors, of approved size. Including marking, drilling

holes in RCC, and fixing with MS/SS anchor bolts using

epoxy/chemical grout for firm anchorage. Ensuring

proper alignment, interlocking, and level of modules.

Including making good the surface after fixing. Finished

with alternate yellow and black stripes using road

marking paint for visibility, complete as per Indian Roads

Congress guidelines and Engineer-in-charge instructions

123 Providing and applying bituminous protective coating on 1747.00 Smt 489.04

RCC/CC surface of underground/basement walls, using

approved quality cold-applied bitumen of grade

conforming to relevant standards, over properly

prepared surface; including cleaning, removal of dust,

dirt and loose particles, and ensuring dry surface

condition; applying one coat of bituminous primer

followed by two or more coats of bituminous coating to

achieve uniform, continuous, and impervious layer of

required thickness; including all labour, materials, tools,

and scaffolding, complete as per as directed by the

Engineer-in-charge.

124 Providing and fixing Polycarbonate Convex Mirror 32 6.00 No 2541.16

Inch of approved quality with top cover fixing on wall

with breckets; Made from lightweight

shatterproof/unbreakable, scratch resistant, strong PC

plastic etc. complete. For all floor

125 Providing and laying cement concrete 1:2:4 (1- Cement : 18.00 Cmt 3741.69

2- Coarse sand : 4- graded stone aggregates 20 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

126 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 2.00 Nos 958.17

size having weight not less than 35Kg.

Item Description of Item Quantity Unit Rate In Amount

127 Providing & erecting open well horizontal mono block 2.00 Nos 25856.00

pump set with cast iron body, complete for three phase

submersible motor having

[H]For 3 H.P,3 phase open well horizontal mono block

pump set suitable for 1400 LPM to 1025 LPM @ 33 to

MTR head suitable for 65/80 mm dia delivery pipe

128 20mm thick sand faced cement plaster on walls upto 3724.00 Smt 347.42

height 10 metres above ground level consisting of 12mm

thick backing coat of C.M. 1:3 (1-cement : 3-sand) and

8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand)

129 Providing and fixing rolling shutters of approved make 11.00 Smt 3554.40

made of 80 mm wide M.S. laths inter-locked together

through their entire length and jointed together at the

ends by end locks mounted on specially designed pipe

shaft with bracket plates, guide channels and

arragements for inside and outside locking with push-

pull operation including the cost of hood cover and

spring etc. complete.(A) Shutters having width below

130 Drilling of min. 250 mm dia. bore hole in all strata 200.00 Rmt 1240.28

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per directed

engineer incharge.

131 Supplying slotted PVC pipes of approved quality at site of 200.00 Rmt 555.50

work confirming to IS. 1239/1974 180mm dia.

132 Bore plug having 100 mm height made from M.S. plate 2.00 No 1161.62

with 3 holes at equal distance on cirCmtference for nut-

bolts type, locking arrangement with nuts-bolts & lock

nuts of std. Make complete. For 250mm dia

133 Providing PVC insulated flat submersible cable as per 150.00 Rmt 180.79

detailed technical specifications of R/C of GWSSB

conforming to IS 694, IEC 60227 / 60228.d)1 R x 3 C x

134 Suppling and installing 3 Phase Borewell 5.0 HP 2.00 No 86900.40

Submersible Pump Sets Electric motor driven

conforming to I.S. 8034 and motor conforms to IS-9283

working at 3 phase 400/440 volt 50 C/S A.C. supply &

2900 R.P.M. cat

135 Providing and fixing check or non return pully wheel 2.00 No 1111.00

valve of 50 mm diameter.

136 Manufacture, supply and delivery of following ISI marked 120.00 Rmt 152.51

HDPE pipes (IS:4984/1985 with latest amendment)

having material Grade PE-80 in approximate 100 meter

coil length or as per GWSSB requirement with SS

nipple at both ends having 11 TPI threads as per

specifications, press fitted and bolted having nominal

diameter as under as per detailed technical

specifications.

Item Description of Item Quantity Unit Rate In Amount

137 Providing and fixing to wall ceiling and floor 10.0 Kg. 60.00 Rmt 339.05

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(G)110

138 Providing and fixing to wall ceiling and floor 10.0 Kg. 100.00 Rmt 696.90

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(G)160

139 Providing junction for rain water juncton chamber of size 8.00 Nos. 9262.71

0.60x0.60x0.75m with excavation of size 1.96x1.96 m &

0.15m thick c.c.1:2:4 bed concrete including brick

masonary wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside &

1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS

steel and 0.60mx0.45m cast iron manhole cover with

frame weight not less than 35 kg as per directed by

Engineer-in-charge

140 Providing and installation Recharge pit of “RAIWOHA” 1.00 Nos. 109645.60

Make 3 layer RCC Precast Injection well system of size

1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V wire

screen of 0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and required Air

vent including all necessary excavation and

transportation at site including required filter media for

the recharge system as per site requirement. this item

including rate of 3 year of maintainance .

141 Constructing brick masonry chamber for underground 6.00 No. 7180.44

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal

dimensions, total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame

15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x 850 mm and

450mm deep for pipe lines with three or more inlets.

142 Providing and laying (two level or slopes) and jointing 40.00 Rmt. 517.91

with stiff mixture of Cement Mortar in proportion 1:1,

Salt glazed stone ware pipes of pipes 150mm laying lime

concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded

brick aggregates 40mm nominal size) bedding for

stoneware pipes of following internal diameters with

necessary formwork and curing complete.

Item Description of Item Quantity Unit Rate In Amount

143 Construction of granular sub-base 150 mm thick by 1313.00 Cmt 1123.12

providing coarse graded machine crushed B.T. material

satisfying MOST specification of grading I (B.T. stone

aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm -

% and 2.36 mm below - 20 % )including spreading in

uniform layer with motor grader on prepared surface,

mixing by mix in place method with rotavator at OMC

and compacting with vibratory roller to achieve the

desired density etc. complete.

144 Providing and fixing of Ridge flashing for roof panel shall 900.00 Smt 867.39

be made out of 0.5 mm thick pre coated GI sheet . The

Precoated sheet shall be of minimum 240 mpa steel

grade confirming to IS 14246:1995 and shall have zinc

coating of minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet and

polyester top coat 15-18 micron. The PPGI Sheet shall

have plastic protective guard film of minimum

microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by pop rivet or

self drilling/self stitching fastners @ maximum 450 mm

c/c along length of capping/flashing etc complete.

145 Providing and fixing pre-cast Rubber Dye / steel Dye 4042.00 Smt 706.93

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming to

IS 15658 : 2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete

146 Providing and fixing pre-cast concrete kerb stone of gray 1252.00 Rmt 374.92

cement based concrete block 30cm ength,30cm height

and 15cm thick of M250 grade concret as per approved

design and including excavation for fixing in proper line

and level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete.

147 Box cutting the road surface to proper slope and camber 2488.00 Cmt. 109.41

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto 50Mt.lead.

148 Providing and laying wet mix macadam base course 250 542.00 Cmt. 1184.73

mm thick in two layers using machine crushed B.T. chips

as per required gradation mixing with required optimum

quantity of water, conveying the mix to site of work,

spreading in to grade and camber with mechanical paver

and consolidation each layer with vibratory roller

including cost of material labour plant and equipment

149 Compaction and finishing of cement concrete road by 3612.00 Smt 63.63

trimix process providing extra Labour charges for the

trimix vaCmte dewatering service process on cement

concrete road sutface by using vacuum dewatering pump

floater surface vibrator including making groves and

rough finish to surface including leveling etc complete.

Item Description of Item Quantity Unit Rate In Amount

150 Constructing providing and fabricating cattle guard using 14.00 Smt 5168.17

channel section frame of size ISMC series 100 mm x

mm (Weight 9.20 kg/Rmt) and ISMC section 100 mm x

75mm (weight 11.50 kg/Rmt) intermediate support for

welding G.I.pipe at 12 Cm C/C of size 50 mm in a frame

made of Channel section size 100 mm x 50 mm all round

including fixing the unit on prepared chamber of

masonary wall using MS hold fast embeded in masonary

wall top as directed by Engineer in charge and as per

drawing and necessary required arrangement etc

151 Providing and fixing decorative entrance gate made out 1088.00 Kg 171.70

of cast iron and various mild steel tabular section

combination , the Ornamental entrance gate should be

fixed at compound wall including pattern and die making

, cutting , welding , grinding, fabrication , fixing in

position at compound wall with necessary pedestal,

bearing block and other locking arrangement. The

entrance gate should be painted with two coats of

priming coat of paint, and two coat of oil paint etc

complete. As per detail design and instruction of

152 Providing and fixing concertina coil fencing with 604.00 Rmt 516.11

punched tape concertina coil 600 mm dia 10 mt openable

length having 50 no rounds per 6 mt length, upto 3mt

height of wall with existing angle iron (50mm x50mm

x5mm )requird shaped As per Directed Engeenier in

charge. placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm) , stud

tied with G.I. staples and G.I. clips to retain horizontal,

including necessary bolts or G.I.barbed wire tied to angle

iron, all complete as per direction of Engineer-in-charge,

with reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at compound

wall for ESR M4/ intakewell.

153 Forming groove of uniform size from 10 x 10 mm and 6040.00 Rmt 52.32

upto 25 x15 mm in plastered surface as per approved

pattern using wooden batten, nailed to the under layer

including removal of wooden battens, repairs to the

edges of plaster panel and finishing the groove complete

as per specifications and direction of the engineer

154 Providing and casting in situ controlled cement concrete 389.00 Cmt 5164.59

M-200 for R.C.C. return as per drawings including

centering shuttering, scaffolding where necessary, laying

vibrating, curing and finishing complete.(A) Height from

0.0 to 5.0 M. (1) Piers (2) Abutment (3) RCC return

155 Earthwork for embankment including breaking clods, 26706.63 Cmt 169.28

dressing with all lead and lift (excluding watering and

consolidation)(E) From Borrow area within 3.0 Km. lead

156 Rolling of Earth work in layers with power roller and 32372.63 Cmt 23.12

watering including filling in depressions which occure

during the process.

Item Description of Item Quantity Unit Rate In Amount

157 Supplying of well rotted FYM manure with all lead and 38.00 Cmt. 454.50

Lift including spreading mixing dressing and rolling with

hand roller etc. complete.

158 Scarifying the surface of Soil including spreading of DAP 1500.00 Smt 42.42

fertilizer mixing with Soil properly levelling gand

dressing of the plot

159 Supplying and planting Dibbing semi carpet lawn at 1500.00 Smt 106.05

distance of abour 15 cm x 15 cm after proper anti termite

teratment amd rolling the seme by hand roller amd

wetering etc complete.

160 Bowing and developing flowering plants grown in nusery 100.00 No. 252.50

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith of soil packed in

polithyline bag or Earthern pot. Including organic &

chemical fertilizer Pesticides, fungicides, hormones &

maintaining the plants up to three months as deserted.

161 Bowing and developing flowering plants grown in nusery 75.00 No. 505.00

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted Trinagle Plan.

162 Bowing and developing flowering plants grown in nusery 50.00 No. 252.50

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as Jasud

163 Bowing and developing flowering plants grown in nusery 75.00 No. 353.50

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as Croton

164 Bowing and developing flowering plants grown in nusery 50.00 No. 151.50

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted green mahindi

165 Bowing and developing flowering plants grown in nusery 50.00 No. 111.10

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted New block ficus.

Item Description of Item Quantity Unit Rate In Amount

166 Bowing and developing flowering plants grown in nusery 75.00 No. 606.00

having approximate height 4 to 6 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted Ashopalav (Polyalthia

167 Bowing and developing flowering plants grown in nusery 20.00 No. 1515.00

having approximate height 4 to 6 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted Brighter Blooms -

168 Labour charges for planting various plantsafter proper 495.00 No. 303.00

anti termite treatment in pits including placing property

and filling the pit with requred prepared mix soil and

wetering and dispporting etc complete.

169 Maintance of the garder for 60 days after Complition of 3 1.00 Job. 101000.00

month stipulated period is completed for plantation o

lawn and plants including applying second round of

proper antitermite tretment.

170 Providing laying and jointing in true line and level 40mm 100.00 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX

or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

171 Providing laying and jointing in true line and level 15mm 140.00 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX

or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

172 Providing and fixing brass screw doen stop cock (A) 15 2.00 No. 555.50

173 Rubber Hose pope 15 mm dia of approved brand and 100.00 Rmt 80.80

174 Providnig and fixing G I Nipple as directed. 2.00 No. 50.50

Item Description of Item Quantity Unit Rate In Amount

175 Supply. installation, testing & commissioning of ISI 1.00 No 98432.21

approved electrical motor driven jockey pump set

having 10.8 m3/hr. @ 70m head. The pump unit shall be

a horizontally direct mounted motor. Unit shall comprise

the following minimum requirements: a) Pump, b)

Electric motor IE2, c) Foundation bolts, d) Mating flanges

with gasket and fasteners, e) Discharge gauges, etc.

complete in all respect, with labour.

176 Supply, installation, testing & commissioning of Priming 1.00 No 25677.97

tank, HDPE type, 1000 litres, with necessary piping

mm size, G.I pipe for priming the pumps, pipe of with

butterfly valves for isolation, Water Filling to priming

tank by piping min. 50 mm size, with all complete.

177 Supply, installation, testing & commissioning of 1.00 No 55635.59

Manifold( surge vessel,)for fire hydrant system, min.

mm diameter, made from M.S plate, hydro tested to

kg./cm2. with ball valves, header with couplings for

fitting pressure switches, pressure gauges etc.with

necessary isolation valves with all complete.

178 Supply, fabrication & erection of aboveground G.I. 'C'- 300.00 Mtr 398.01

Class, ERW piping, conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm dia.

& above, thickness. G.I. pipe fitting's as per IS: 1239, part-

II, Heavy class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts & washers,

3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red

conf. to IS: 5, Shade 536. Complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. 25 mm dia.

179 Supply, fabrication & erection of aboveground G.I. 'C'- 300.00 Mtr 641.95

Class, ERW piping, conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm dia.

& above, thickness. G.I. pipe fitting's as per IS: 1239, part-

II, Heavy class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts & washers,

3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red

conf. to IS: 5, Shade 536. Complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. 50 mm dia.

Item Description of Item Quantity Unit Rate In Amount

180 Supply, fabrication & erection of aboveground G.I. 'C'- 200.00 Mtr 1176.91

Class, ERW piping, conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm dia.

& above, thickness. G.I. pipe fitting's as per IS: 1239, part-

II, Heavy class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts & washers,

3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red

conf. to IS: 5, Shade 536. Complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. 80 mm dia.

181 Supply, fabrication & erection of aboveground G.I. 'C'- 200.00 Mtr 1690.47

Class, ERW piping, conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm dia.

& above, thickness. G.I. pipe fitting's as per IS: 1239, part-

II, Heavy class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts & washers,

3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red

conf. to IS: 5, Shade 536. Complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. 100 mm dia.

182 Supply, fabrication & erection of aboveground G.I. 'C'- 200.00 Mtr 2525.00

Class, ERW piping, conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm dia.

& above, thickness. G.I. pipe fitting's as per IS: 1239, part-

II, Heavy class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts & washers,

3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red

conf. to IS: 5, Shade 536. Complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. 150 mm dia.

Item Description of Item Quantity Unit Rate In Amount

183 Supply, fabrication & erection of aboveground G.I. 'C'- 13.00 Mtr 3423.73

Class, ERW piping, conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm dia.

& above, thickness. G.I. pipe fitting's as per IS: 1239, part-

II, Heavy class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts & washers,

3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire red

conf. to IS: 5, Shade 536. Complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. 200 mm dia.

184 Supply, installtion, testing & commissioing of 20.00 Mtr 2020.00

Underground GI (ERW) piping conforming to IS:1239,

part-I, Heavy class ('C' class) up to 150 mm dia. and

IS:3589 Heavy class ('C' class), for 200 mm dia. & above,

min. 6.35mm thickness including Heavy class fittings,

anti-corrosive tape of size 150 mm wide x 4 mm thick,

wrapping & coating with 13KV holiday testing . Rates

shall include sand bedding of 75mm dia all around,

backfilling of the excavated including installation of

heavy pipe fitting's, flanges, etc. 10 % of all the welded

joints shall be done radiographically tested and 50% of

the joints radiographed shall be the "Field Joints".

Hydrostatic testing for 2 hours at 150% of the system

pressure, hook-up etc., complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. (Road

Crossing) 100 mm dia.

185 Supply, installtion, testing & commissioing of 30.00 Mtr 3047.12

Underground GI (ERW) piping conforming to IS:1239,

part-I, Heavy class ('C' class) up to 150 mm dia. and

IS:3589 Heavy class ('C' class), for 200 mm dia. & above,

min. 6.35mm thickness including Heavy class fittings,

anti-corrosive tape of size 150 mm wide x 4 mm thick,

wrapping & coating with 13KV holiday testing . Rates

shall include sand bedding of 75mm dia all around,

backfilling of the excavated including installation of

heavy pipe fitting's, flanges, etc. 10 % of all the welded

joints shall be done radiographically tested and 50% of

the joints radiographed shall be the "Field Joints".

Hydrostatic testing for 2 hours at 150% of the system

pressure, hook-up etc., complete with all accessories as

per approved drawings, specicification and direction of

the Engineer-in-Charge, with all complete. (Road

Crossing) 150 mm dia.

Item Description of Item Quantity Unit Rate In Amount

186 Design , Supply and installation of Safety Signage made of 10000.00 Sq. inch 9.42

Zinc Sulphilde based glow in dark , Rigid sheet with High

Luminous property enclosed in a transperent weather

proof UV stabilized plastic pasted on 3 mm thick clear

acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT

USE LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT, FIRE HOSE

REEL, FIRE HYDRANT POINT etc.

187 Supply, Installtion, Testing & Commissioing of Standard 200.00 No 556.36

Response Sprinkler, Pendent Brass Sprinkler, Quartzoid

Bulb type with crome finish, nickel crome platde, K factor

K-80, Temp.- 680C, 1/2" end connection including

resessed escutcheon. (UL Listed).

188 Supply, installation, testing & commissioning of pressure 3.00 No 2824.58

switch. (Range 0 to 16 kg/cm2)

189 Supply, installation, testing & commissioning of 150 mm 8.00 No 2738.98

dia. dial Burdon Type Glycerine Filled pressure gauge

with isolation ball valve arrangements with necessary

isolation valves with all complete.( Range 0 to

190 Supply, installation, testing & commissioning of Cast 4.00 No 5905.93

iron body double flanged gate valve With Rising Spinldle

conf. to IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges, galvanized nut,

bolts & washers, gasket 3 mm thick, etc., with all

complete. 50 mm dia.

191 Supply, installation, testing & commissioning of Cast 4.00 No 8182.71

iron body double flanged gate valve With Rising Spinldle

conf. to IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges, galvanized nut,

bolts & washers, gasket 3 mm thick, etc., with all

complete. 80 mm dia.

192 Supply, installation, testing & commissioning of Cast 6.00 No 10271.19

iron body double flanged gate valve With Rising Spinldle

conf. to IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges, galvanized nut,

bolts & washers, gasket 3 mm thick, etc., with all

complete. 100 mm dia.

193 Supply, installation, testing & commissioning of Cast 6.00 No 15920.34

iron body double flanged gate valve With Rising Spinldle

conf. to IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges, galvanized nut,

bolts & washers, gasket 3 mm thick, etc., with all

complete. 150 mm dia.

194 Supply, Installation, Testing & Commissioning of Cast 10.00 No 2011.44

iron body Butterfly valve according to IS: 13095, PN-1.6,

Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with

mating flanges /ANSI class # 150 with bolts & nuts

washers, rubber gaskets 3 mm thick, etc., with all

complete. 50 mm dia.

Item Description of Item Quantity Unit Rate In Amount

195 Supply, Installation, Testing & Commissioning of Cast 6.00 No 2567.80

iron body Butterfly valve according to IS: 13095, PN-1.6,

Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with

mating flanges /ANSI class # 150 with bolts & nuts

washers, rubber gaskets 3 mm thick, etc., with all

complete. 80 mm dia.

196 Supply, Installation, Testing & Commissioning of Cast 6.00 No 3124.15

iron body Butterfly valve according to IS: 13095, PN-1.6,

Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with

mating flanges /ANSI class # 150 with bolts & nuts

washers, rubber gaskets 3 mm thick, etc., with all

complete. 100 mm dia.

197 Supply, Installation, Testing & Commissioning of Cast 8.00 No 4493.64

iron body Butterfly valve according to IS: 13095, PN-1.6,

Iron Disc for size 150 mm dia. & below Lever operated

and above 150 mm dia. Gear operated complete with

mating flanges /ANSI class # 150 with bolts & nuts

washers, rubber gaskets 3 mm thick, etc., with all

complete. 150 mm dia.

198 Supply, installation, testing & commissioning of Cast iron 5.00 No 1540.68

body Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6

complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all complete

Accessories 50 mm dia.

199 Supply, installation, testing & commissioning of Cast iron 4.00 No 2225.42

body Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6

complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all complete

Accessories 80 mm dia.

200 Supply, installation, testing & commissioning of Cast iron 6.00 No 3166.95

body Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6

complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all complete

Accessories 100 mm dia.

201 Supply, installation, testing & commissioning of Cast iron 4.00 No 5820.34

body Dual Plate Wafer Type NRV conf. to IS: 210, PN-1.6

complete with mating Flanges class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all complete

Accessories 150 mm dia.

202 Supply, installation, testing & commissioning of SG iron 4.00 No 1112.71

body SinglePlate Wafer Type NRV conf. to ASTMA

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete. Accessories 50 mm dia.

203 Supply, installation, testing & commissioning of SG iron 1.00 No 1455.08

body SinglePlate Wafer Type NRV conf. to ASTMA

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete. Accessories 80 mm dia.

Item Description of Item Quantity Unit Rate In Amount

204 Supply, installation, testing & commissioning of SG iron 1.00 No 1797.46

body SinglePlate Wafer Type NRV conf. to ASTMA

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete. Accessories 100 mm dia.

205 Supply, installation, testing & commissioning of Y Type 2.00 No 5563.56

Strainer complete with mating flanges with bolts & nuts,

washers, gaskets 3 mm thick, etc., with all complete

accessories. 80 mm dia.

206 Supply, installation, testing & commissioning of Y Type 3.00 No 7275.42

Strainer complete with mating flanges with bolts & nuts,

washers, gaskets 3 mm thick, etc., with all complete

accessories. 100 mm dia.

207 Supply, installation, testing & commissioning of Y Type 2.00 No 11555.08

Strainer complete with mating flanges with bolts & nuts,

washers, gaskets 3 mm thick, etc., with all complete

accessories. 150 mm dia.

208 Supply, installing, testing and commissioning of Normax 2.00 No 4194.07

make CI heavy duty ball type foot valve with flanges, nut

bolts, gaskets etc. with necessary complete accessories.

209 Supply, installing, testing and commissioning of Normax 2.00 No 6162.71

make CI heavy duty ball type foot valve with flanges, nut

bolts, gaskets etc. with necessary complete accessories.

210 Supply, installing, testing and commissioning of Normax 2.00 No 12411.02

make CI heavy duty ball type foot valve with flanges, nut

bolts, gaskets etc. with necessary complete accessories.

211 Supply, installation, testing & commissioning of Four way 1.00 No 8987.29

fire brigade Inlet connection with 63 mm dia. stainless

steel (SS304) instantaneous male inlets with built in non

return valve in each inlet with 150 mm dia. header pipe,

suitable rubber cap and GI chain including nuts, bolts,

washers, gasket 3 mm thick, etc. with all complete.

212 Supply, installation, testing & commissioning of Two way 1.00 No 5135.59

fire brigade Inlet connection with 63 mm dia. stainless

steel (SS304) instantaneous male inlets with built in non

return valve in each inlet with 100 mm dia. header pipe,

suitable rubber cap and GI chain including nuts, bolts,

washers, gasket 3 mm thick, etc. with all complete.

213 Supplying FIRE bucket round bottom of 9 liters capacity 12.00 No 1027.12

made out of 24 gauge G.I Sheet with extra handle at

bottom duly painted white inside and Red out side with

FIRE mark. Filled with dry-sand and kept on existing

stand provided or hung on wall hook.

214 Supplying and erecting floor mounting Stand for keeping 3.00 No 5563.56

four nos. of FIRE buckets comprising 1500 mm in length,

900 mm height frame made out of 30mm x 30 mm x

mm angle iron with cross supports legs, welded with

hooks and duly painted with one coat of primer and two

coats of approved enamel P O red paint.

Item Description of Item Quantity Unit Rate In Amount

215 Supply & installation of stainless steel body Orifice Plate 12.00 No 1069.92

of suitable inner bore along with matching flange - as per

specification & requirement as per hydraulic calculation.

216 Providing and fixing approved make Perforated C type 25.00 Mtr 471.67

cable tray. Made from pre- galvanized sheet steel. The

cable tray should be bended as per IS 2062/1079 . with

max 17.5% perforation with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected

on existing support as per Specification and as per

instruction of engineer in charge..(5) 300 X 50 X 1.5 mm

217 Providing and fixing approved make Perforated C type 25.00 Mtr 322.19

cable tray. Made from pre- galvanized sheet steel. The

cable tray should be bended as per IS 2062/1079 . with

max 17.5% perforation with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected

on existing support as per Specification and as per

instruction of engineer in charge..(3) 150 X 50 X 1.5 mm

218 Supply, installation, testing & commissioning of Oblique 12.00 No 5435.17

pattern type stainless steel (SS 304) single headed

External Fire Hydrant Valve with 63 mm dia. female

instantaneous outlet conf. to IS: 5290, type - A, including

mating flanges, galvanised nuts, galvanised bolts/studs,

washers & gaskets 3 mm thick with all complete.

219 Supply, installation, testing & commissioning of 63 mm 12.00 No 1754.66

dia. stainless steel (SS 304) Universal Branch Pipe conf.

220 Supply & installation, testing & commissioing of Fire 12.00 No 6967.29

Fighting Hose - conf. to IS : 636, type B (type- 3), The fire

hose shall be 15 m long with 63 mm dia. stainless steel

(SS 304) couplings conf. to IS: 903, at both the ends for

connection with the hydrant valve and the branch pipe.

221 Supply, installation, testing & commissioning of 12.00 No 2525.00

fabricated from 3 mm MS sheet, hose box of size-450 mm

x 600 mm x 250 mm - painted with Fire Red as per IS:

shade no. 536 front 3 mm thick transparent glass with

lock & key, handle and brass hinges - to accommodate

one number of 15 mtr long hose and one number of

universal branch pipe, including supporting arrangement

with civil work.

222 Supply, Installation, testing & commissioing of Swinging 12.00 No 7403.81

type mild steel hose reel drum with 20 mm dia. x 30 mtr.

rubber hose as per IS: 884. The mounting stand shall be

of mild steel and the hose shall be fitted with a SS shut-

off nozzle & SS ball valve of 25 mm dia. including

supporting arrangement with all complete. accessories

223 Supplying, fixing & testing of of CI ball Valve 25mm dia. 30.00 No 706.14

224 Supplying, fixing & testing of New Battery of diesel 1.00 No 15834.75

engine 150 Amp.

225 Supply and installation of Diesel Tank For Diesel Engine 1.00 No 16690.68

With All Accessories 100 Ltrs.

226 Supplying, filling & testing lube oil for diesel engine 20.00 Ltrs 320.97

Item Description of Item Quantity Unit Rate In Amount

227 Supply and commissioning of Oil Filter. 1.00 No 706.14

228 Supplying, filling of diesel in diesel engine tank 100.00 Ltrs 89.87

229 Supply and commissioning of Diesel Filter 1.00 No 427.97

230 Supplying, filling & testing coolant to engine cooling for 20.00 Ltrs 239.66

231 Filling Of Gaps Between pipe and Core Cutting Hole With 106.00 No 299.58

Chemical and Cement

232 Supplying & erecting XLPE(IS:7098)(I)-88 ISI 100.00 Mtr 136.35

unarmoured copper cable 1.1 KV grade to be erected as

directed of following size. (E) 3 core 2.5 Sq. mm for

pressure switch

233 Providing and erecting XLPE(IS:7098)(I)-88 ISI 90.00 Mtr 285.83

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump) (B)

3 core 4 Sq. mm

234 Providing and erecting XLPE(IS:7098)(I)-88 ISI 75.00 Mtr 497.93

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump) (D)

3 core 10 Sq. mm (Only Fire Panel to Fire Pump)

235 Providing and erecting XLPE(IS:7098)(I)-88 ISI 30.00 Mtr 213.11

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable for Diesel Engine Battery Charger

(A) 3 core 2.5Sq. mm

236 Supply, Filling and Fixing of approved make ABC type 30.00 No 1968.64

fire extinguisher - 6 Kg. Capacity as per IS:15683 & IS :

237 Supply, Filling and Fixing of approved make CO2 type 30.00 No 5520.76

fire extinguisher. Capacity 4.5 Kg. (conforming to IS-

238 Supply, Filling and Fixing of approved make ABC 8.00 No 3423.73

Moduler type automatic fire extinguisher. Capacity 5 Kg.

(conforming to IS-15683).

239 Submitting the application to obtain Fire Plan Approval 1.00 No 252500.00

and After Completion of Work Obtain Final Fire NOC for

240 Supply, Installation and commissioning of Air Release 4.00 No 1412.29

Valve, 25 mm Dia. connection.

241 Supply, Installation and commissioning of Fire Alarm 1.00 No 35350.00

Panel Conventional type, 8 zone, with complete

242 Supply, Installation and commissioning of smoke 200.00 No 1027.12

detectors / heat detectors, with complete accessories.

243 Supply, Installation and commissioning of plug in base 200.00 No 256.78

for the smoke detectors, hooters, with complete

244 Supply, Installation and commissioning of Audio hooters , 10.00 No 1069.92

with complete accessories.

245 Supply, Installation and commissioning of Manual Call 10.00 No 1010.00

Points, with complete accessories.

Item Description of Item Quantity Unit Rate In Amount

246 Providing and erecting XLPE(IS:7098)(I)-88 ISI 2300.00 Mtr 176.75

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (A)

core 2.5 Sq. mm for Fire Alarm System

247 Core cutting in wall and in RCC slab with size as below: 60.00 No 342.37

50 mm dia. Hole

248 Core cutting in wall and in RCC slab with size as below: 10.00 No 427.97

80 mm dia. Hole

249 Core cutting in wall and in RCC slab with size as below: 10.00 No 513.56

100 mm dia. Hole

250 Core cutting in wall and in RCC slab with size as below: 16.00 No 599.15

150 mm dia. Hole

251 Core cutting in wall and in RCC slab with size as below: 10.00 No 855.93

200 mm dia. Hole

Item Description of Item Quantity Unit Rate In Amount

252 Supply, installation, testing & commissioning of ISI 1.00 Set 186850.00

approved electrical motor operated Kirloskar make fire

hydrant main pump set horizontal end suction back pull

out top discharge centrifugal fire pump set with all the

standard acessories, base frame, coupling, and

foundation bolts with following specifications

Model -DB 80/26,

Motor Rating -30KW/40HP/3 ph

Suc x Del - 80 x

253 Supplying, Installation, Testing and commissioning of 1.00 Set 419150.00

Kirloskar make diesel engine driven fire hydrant pump

set suitable for automatic operation and consisting of

following: horizontal type, centrifugal end suction back

pull out, top discharge pump of cast iron body & bronze

impeller with m.s.fabricated common base plate,

coupling, coupling guard, foundation bolts etc.,as

Engine - 45 HP / 3 ph

Suc x Del - 100 x

254 Fire Hydrant Panel suitable for 10 hp Jockey pump, 40 hp 1.00 No 117160.00

(97 m3/hr @ 70 m head) main electrical pump and 45 hp

(97 m3/hr @ 70 m head) Diesel engine operated pump

R Y B Indication - 1 Set

VAF Digital Meter - 1 Set

F1 40 HP Star Delta Starter - 1 For Main pump

F2 10 HP DOL Starter - 1 For Jockey Pump

F3 Auto - On / Off Diesel Pump With Battery Charger

Control Circuit With Auto - Manual On/Off

On/Off Trip Indication

On/Off Push Button

Dully Powder Coated PO Red Colour,

Fabricated From 14/16 SWG,GI Sheet , IP-42 Protection,-

Fixed Type Floor Mounted

Cable Entry : Bottom

255 Pay Legal Fees to Concern Authority for Obtaining Plan 8500.00 Sq.mt 15.15

Approval and Final NOC

Item Description of Item Quantity Unit Rate In Amount

256 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 817.00 Pt. 582.77

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/ metallic/ white front plate

modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

257 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 415.00 Pt. 809.01

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/ Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

258 Point wiring for on board Looped Plug with 6A Modular 138.00 Pt. 309.06

type switch & 5 pin socket erected on PVC/ Metallic/

Wooden box, single mounting base frame covered with

textured / metallic/ white front plate modules erected

on/ in wall/ ceiling with following type accessories Cat.

259 Providing following type of Modular Type Accessories 202.00 Nos 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (1)One No. SP 6 Amp. Cat.III

260 Providing following type of Modular Type Accessories 202.00 Nos 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (2) One No 5 pin plug Cat.III

261 Providing following type of Modular Type Accessories 5.00 Nos 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (3) Two Pin/RJ-11 Telephone Socket

[A] For One Gang Cat.III

Item Description of Item Quantity Unit Rate In Amount

262 Providing following type of Modular Type Accessories 134.00 Nos 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket Cat.III

263 Providing following type of Modular Type Accessories 247.00 Nos 180.79

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way switch

264 Providing following type of Modular Type Accessories 247.00 Nos 199.98

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal socket

265 Providing and erecting ISI mark Medium class RIGID PVC 3510.00 Mtr. 33.33

PIPES of following size complete to be erected on/in wall

or ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed

266 Providing and erecting Mains with 1.1 KV grade FRLS 9480.00 Mtr. 104.03

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) With

medium class Rigid PVC pipe and accessories (b) 2 wire

267 Providing and erecting Mains with 1.1 KV grade FRLS 7075.00 Mtr. 140.39

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (a) 2 wire 4 sq. mm

268 Providing and erecting Mains with 1.1 KV grade FRLS 360.00 Mtr. 184.83

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (b) 2 wire 6 sq. mm

269 Providing and erecting Mains with 1.1 KV grade FRLS 1000.00 Mtr. 226.24

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (g) 4 wire 4 sq. mm

Item Description of Item Quantity Unit Rate In Amount

270 Providing and erecting Mains with 1.1 KV grade FRLS 840.00 Mtr. 326.23

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (h) 4 wire 6 sq. mm

271 Providing and erecting Mains with ISI marked, 1.5KV 300.00 Mtr. 70.70

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(e) One wire 6.00 sq. mm

272 Providing and erecting Mains with ISI marked, 1.5KV 255.00 Mtr. 115.14

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(f) One wire 10.00 sq. mm

273 Providing and erecting Mains with ISI marked, 1.5KV 42.00 Mtr. 177.76

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(g) One wire 16.00 sq. mm

274 Providing and erecting Mains with ISI marked, 1.5KV 33.00 Mtr. 376.73

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(i) One wire 35.00 sq. mm

275 Providing and erecting Mains with ISI marked, 1.5KV 9.00 Mtr. 588.83

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(j) One wire 50.00 sq. mm

276 Supplying and erecting Flexible PVC insulated multi 265.00 Mtr. 97.97

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed.(h) 2.50 Sq.mm

3 core round PVC sheathed

277 Supplying & erecting approved make LAN cable of 4020.00 Mtr. 47.47

following size in existing pipe as per direction [C] CAT -

Item Description of Item Quantity Unit Rate In Amount

278 Supplying & erecting approved make Telephone Cable 150.00 Mtr. 20.20

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections. [A] Conductor Size

mm (a) Unarmoured (2) Two Pairs

279 Providing & erecting main Distribution (MDF) indoor 1.00 Mtr. 1368.55

type, back mounted frame as per DoT standard approved

with krone strips (b) Suitable for 20 pair

280 Providing & erecting Switch board for Computer or 134.00 Nos. 1133.22

electric apparatus consisting of following modular type

accessories mounted with PVC/ Metallic concealed/

open box with single mounting base frame covered with

textured/ metallic/ white front plate,modules erected

with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories

281 Providing & erecting insulated socket 3P+N+E with 100.00 Nos. 1706.90

Plug16A rating which is comprised of Four pole MCB slot

and insulated socket IP40 cat-III

282 Supplying and erecting LED indoor fittings with LEDs of 619.00 Nos. 535.30

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/ CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95,

THD < 15%, CCT 3000 K to 6500K, Luminaire efficacy>

85 lumens/ watt, LED driver efficiency > 85 % (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Tube

Light with integral driver (v) 36-40 Watts, Surge-2 KV, IP-

20, conventional 4 feet Cat.III

283 Supplying and erecting led lamps with following wattage 20.00 Nos. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (ii) 5 to 8 watts Cat-III

Item Description of Item Quantity Unit Rate In Amount

284 Supplying and erecting LED indoor fittings with LEDs of 149.00 Nos. 1794.77

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/ CRCA/

aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/ name 160V

to 270V, Power Factor more than 0.95, THD < 15 %, CCT

3000 K to 6500K, Luminaire efficacy> 85 lumens/watt,

LED driver efficiency > 85 % (fitting required LM-79 &

LM-80 Certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (B) LED Panel Light with

provision for Plane front frame with translucent cover

fixed to housing complete.IP20 (vi) 36 watts, 24" x 24",

Surge- 2KV Cat.III

285 Supplying and erecting LED street light / Flood light 52.00 Nos. 4248.06

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %. (fittings

required LM-79 & LM-80 certificates) (NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (ii) 48 - 59 Watts Cat.III

286 (B) Flood Light (IP-65), Surge protection -4KV integral 32.00 Nos. 9196.05

and ,Light must have 440VAC line supply with over-

voltage protection. (vii) 200 - 250 watts Cat.III

287 (C) Post Top Lantern LED fitting comprises of finish cast 2.00 Nos. 4096.56

aluminum spigot and spun aluminum canopy fixed with

opal polycarbonate, pipe arrangement for vertical

mounting driver and accessories wired upto terminal

block.IP 65 (ii)32-40W Cat-III

288 (c) LED Bollard fittings of minimum height 1000 mm & 8.00 Nos. 3792.55

dia.100mm having polycarbonate clear/milky diffuser

mounted on 3mm thick aluminium finished powder

coated pipe with base plate 160x160mm with erection

by M8x75mm fastner with required RCC foundation.IP65

for 9 to 20 watt and above ,surge-4kv cat-III

Item Description of Item Quantity Unit Rate In Amount

289 Providing and erecting Approved make Four pole 4.00 Nos. 6790.23

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up to

25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing. ICS=100% of

ICU only Cat III

290 Providing and erecting Approved make Four pole 18.00 Nos. 8861.74

moulded case circuit breaker having breaking capacity

ICU of 35 KA. at 415 V. having normal current rating

125A. with Fixed thermal & magnetic release suitable to

work on A.C.supply 50 Hz. with all internal connections,

spreader tinned copper & complete erected in existing

16 G.M.S. housing. ICS=100% of ICU only Cat III

291 Providing and erecting Approved make Four pole 7.00 Nos. 23041.13

moulded case circuit breaker having breaking capacity

ICU of 35 KA. and above at 415 V . having normal current

rating 250A. with variable thermal & magnetic release

suitable to work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing. ICS=100% of ICU

292 Providing and erecting Approved make Four pole 1.00 Nos. 27751.77

moulded case circuit breaker having breaking capacity

ICU of 50 KA and above at 415 V having Normal current

rating 400A. with variable Thermal & magnetic release

suitable to work on A.C.supply 50 c/s. With all internal

connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing. ICS=100% of ICU

293 Providing and erecting Approved make Earth fault Relay 1.00 Nos. 5956.98

suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT

ratio & MCCB rating as following along with shunt trip

220V AC. with all internal connections & complete

erected in existing M.S.housing.. (3) 250 A -400 A , CT

294 Supplying & erecting approved make Four Pole 415V 1.00 Nos. 22255.35

change over switch interior for panel mounting with

operating mechanism A.C.23 duty confirming to IS for

295 Supplying and erecting triple pole & neutral 440V /500V 6.50 Rmt 1961.42

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current /cross section area) duly

wrapped with colour insulating tape for phase sequence

of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (A) Suitable for 100 Amp.

Item Description of Item Quantity Unit Rate In Amount

296 Supplying and erecting triple pole & neutral 440V /500V 1.00 Rmt 3202.71

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current /cross section area) duly

wrapped with colour insulating tape for phase sequence

of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (B) Suitable for 200 Amp.

297 Supplying and erecting triple pole & neutral 440V /500V 2.00 Rmt 7319.47

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current /cross section area) duly

wrapped with colour insulating tape for phase sequence

of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (D) Suitable for 400 Amp.

298 Providing and erecting Miniature circuit breaker single 87.00 Nos. 297.95

pole 0.5A to 2A system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

299 Providing and erecting Miniature circuit breaker single 426.00 Nos. 123.22

pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

300 Providing & erecting 240 V MCB double pole switch for 108.00 Nos. 362.59

motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing box

having following capacity (B) 40 Amp. Cat.III

301 Providing & erecting 415 V MCB Four Pole for Motor & 56.00 Nos. 736.29

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (b)40 Amp. Cat.III

302 Providing & erecting 415 V MCB Four Pole for Motor & 97.00 Nos. 811.03

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (c)63 Amp. Cat.III

303 Sheets steel powder coated enclosure suitable for 50.00 Nos. 176.75

incorporating One/Two nos. MCB.

304 Providing and erecting Sheet Steel powder coated MCB 6.00 Nos. 1492.78

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (A) single

phase incoming and horizontal single phase outgoing (b)

sheet steel double door (IP-43) (iv)12 way

Item Description of Item Quantity Unit Rate In Amount

305 Providing and erecting Sheet Steel powder coated MCB 21.00 Nos. 2913.85

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI) (b) sheet steel

double door (ii)6 way

306 Providing and erecting Approved make RCCBs 69.00 Nos. 2458.34

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(ii) 40Amps. DP Cat. III

307 Providing and erecting Annealed bare Copper wire 8 to 137.00 Kg. 794.87

308 Providing and erecting Pipe type earthing having 150 13.00 Nos. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

309 For using salt and charcoal / coke as required for pipe 13.00 Nos. 171.70

310 Supplying & erecting earth pit of minimum bore 16.00 Nos. 4591.46

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of

installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing

resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted

by Agency. (a) For Electrical Installation up to 440V in

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Item Description of Item Quantity Unit Rate In Amount

311 Providing & erecting weather proof, dust & vermin proof, 21.40 Smt. 14902.55

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG

thick CRC M.S. sheet for outer body & doors, 16 SWG

thick CRC M.S.sheet for internal partitions with

necessary accesories, supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per requirements

& instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips,

rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and

rubber gasket,heavy duty end terminal

connection,danger notice board, necessary ventilation,

earthing strip complete. The Panel shall be painted with

epoxy powder coating. (The rates excludes the cost of

switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams) The panel shall

be supplied with following approved manufacturers with

following size. (B) The standard companies switch gear

shall be used and only manufacturers at CPRI approved

factory (i) with 350 mm depth

312 Providing and erecting ,Fabricating the box type items 360.00 Kg. 180.79

made from M.S. Sheet with A.I. supports, wings, doors,

handles other hardware materials as per requirement

design with finishing by three tank powder coating

processed inside and outside painted, erected as

directed including minor civil work.

313 Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI 260.00 Mtr. 454.50

armoured cable multistrand Aluminium conductor for

1.1 kV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (D)

1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

314 Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI 630.00 Mtr. 648.42

armoured cable multistrand Aluminium conductor for

1.1 kV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (F)

1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

315 Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI 400.00 Mtr. 1401.88

armoured cable multistrand Aluminium conductor for

1.1 kV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (I)

1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

316 Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI 2290.00 Mtr. 151.50

armoured cable multistrand / Solid Aluminium

conductor for 1.1 kV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of

cables (B) 4 core 6 Sq. mm

Item Description of Item Quantity Unit Rate In Amount

317 Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI 120.00 Mtr. 229.27

armoured cable multistrand Aluminium conductor for

1.1 kV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (B)

318 Making trench in soft soil of suitable width of 90 cm deep 2250.00 Mtr. 55.55

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

319 Making trench in Hard Murrum / Tar Road of suitable 360.00 Mtr. 74.74

width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

320 (B) If additional machinery like hammer driller or JCB 80.00 Mtr. 357.54

321 Providing & laying approved make Double walled 2745.00 Mtr. 137.36

corrugated pipes (DWC) of polyethylene (conforming to

IS 14930 II) with necessary connecting accessories of

same material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (D)120 mm outer dia.

322 Providing and, fixing heavy duty flange type brass cable 172.00 Nos. 38.38

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (B) 2 to 4 core 6 Sq. mm

323 Providing and, fixing heavy duty flange type brass double 14.00 Nos. 103.02

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (C) 3 &

1/2 core 70 Sq. mm

324 Providing and, fixing heavy duty flange type brass double 4.00 Nos. 247.45

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (H) 3 &

1/2 core 240 Sq. mm

325 Solder less crimping type Aluminium lugs conforming to 688.00 Nos. 6.06

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/ cadmium plated nut bolts in an

approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

326 Solder less crimping type Aluminium lugs conforming to 48.00 Nos. 25.25

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/ cadmium plated nut bolts in an

approved manner. (E) 70 Sq.mm.

327 Solder less crimping type Aluminium lugs conforming to 24.00 Nos. 45.45

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/ cadmium plated nut bolts in an

approved manner. (G) 120 Sq.mm.

Item Description of Item Quantity Unit Rate In Amount

328 Solder less crimping type Aluminium lugs conforming to 16.00 Nos. 85.85

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/ cadmium plated nut bolts in an

approved manner. (J) 240 Sq.mm.

329 Providing and fixing approved make Perforated C type 840.00 Rmt 424.20

cable tray. Made from sheet steel. The cable tray should

be single or double bended as per required and as per IS

2062/1079 and shall be coated with hot dip galvanizing

as per IS 2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt

and washers etc. erection with necessary support(

included) as per Specification and as per instruction of

engineer in charge.. (3) 150 X 50 X 1.6 mm Thick

330 Providing and fixing approved make Ladder type cable 70.00 Rmt 523.18

tray. Made from M.S sheet. The cable tray should be

bended as per IS 2062/1079 shall be fabricated of double

bended channel section longitudinal members with

single bended Channel section. Rungs of members

welded to the base of the longitudinal members at

mm c/c spacing . as per IS and shall be coated with hot

dip galvanizing as per IS 2629/4759. with coupler plate

/ Fish plate and GI hardware like nut - bolt and washers

etc. erected on existing support as per Specification and

as per instruction of engineer in charge.. (8) 150 X 100 X

331 Providing and erecting Approved make Ceiling fan with 405.00 Nos. 1596.81

double ball bearing ISI mark with condenser A.C.

23OV.50 c/s.1200 mm. sweep complete, canopy erected

on existing hook or clamp with earthing. [Make shall be

approved by Engineer in charge]

332 Supplying and erecting 19 / 20 mm. nominal bore 405.00 Mtr. 108.07

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage

333 Supplying & erecting fan hook box of 10 mm M.S. round 405.00 Nos. 108.07

bar bounded to the RCC bars up to 50mm length each

side and pierced through a 16 Gauge M.S. box / Heavy

Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

334 Supplying & erecting single phase approved make 26.00 Nos. 3082.52

industrial exhaust fan suitable for medium duty ring

mounted low noise operation suitable for medium duty

having following dia size and maximum speed in RPM [C]

380 mm dia 1400 RPM Cat.II

Item Description of Item Quantity Unit Rate In Amount

335 Supplying and erecting approved make Octagonal pole 52.00 Nos. 7561.87

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as per

IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of

min 6mm Hylam sheet, standard profile 35mmX7.5mm

Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With

Suitable foundation (Included) as per details given by

manufacturer considering site requirement. (C) 5 Mtr.

Long 70 mm Top X 130 mm bottom dia, 3 mm thickness

with 200mmX200mmX12mm base plate, 4-M16 Bolts

and 600mm long with necessary G.I. J Bolts .Approx Pole

336 Supplying and erecting Street light pole bracket 43.00 Nos. 491.87

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [A] Single Arm bracket

337 Supplying and erecting Street light pole bracket 1.00 Nos. 622.16

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [B] Double Arm Bracket

338 Supplying & erecting approved make SMC press 42.00 Nos. 476.72