MVIPFabrication painting and erection of new steel shutters for the cross regulator at LBMC ch29045 m

Amount

Supply of the following Materials for the fabrication of structural steel wheel Shutter of Size 3.75M[W]x2.9M[H]-1No.and its acessories etc.complete.

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.103 : Supply of MS checquered plates including cost of conveyance charges

85.106 : Supply of MS flats including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

Fabrication & supply of structutral steel wheel shutter and its acessories,supply and fixing of cast steel whel assy [dia125mm/100mm],supply and fixing of rubber seals etc.as per approved specification and direction of deptl.officials at site.

85.110 : Fabrication and supply of Structural steel wheel gate and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

od2114/2018_2019/MH : Supplying and Fixing of Cast Steel wheel assembly consisit of 125mm dia.,100mm thk. with 32mm roller axle etc.including cost of all materials,conveyance and labour charges etc.complete as directed by the departmental officer at site.

85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.117 : Supplying and fixing in correct position with specified initial interface the Angular type rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.112 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350microns over the grit blasted and cleaned surface to class A standard of IS 14177 including cost of all materials , labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc complete as per the direction of departmental officer at site

85.108 : Fabrication, erection and commissioning of Structural steel Embedded parts in IS2062 Grade and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour , machinery , incidental and handling charges etc complete but excluding cost of material already supplied

60.1.2 : RING BUND Type II Putting up ring bund with earth fille gunny bags of top width 1.0m bottom width 2.0m height 2.0 m side and filling in between with earth to form ring bund and maintaining the same leak proof till the completion of the work and clearing the site by dismantling the bund after completion of the work.etc.complete.

50.2.3.1 : Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

od20532/2018_2019/MH : Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track,Seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

Providing Pillars by using RCC including earth work excavation and demolishing cement concrete and laying CC in retaining walls etc.complete.

4.2.2 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:11/2:3 (1 cement : 11/2 coarse sand :3 graded stone aggregate 20 mm nominal size)

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.3.1 : Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Providing operating mechanism for the shutter with 2Nos.of Gear Box units and 63mm dia screw rods-2Nos.etc.including fabrication of supporting steel structure for operating mechanism with ladder 1No.etc.complete.

od7512/2018_2019/MH : Supply of Gear box unit, consist of worm & worm wheel assy. having a lifting speed of around 0.005m/min for 24 rpmof hand operation appxly.- with hand operating system-to transmit torque, not less than 6000 Kg-cm with minimum of 20 threads of 12 mm internal square thread on nuts having a total reduction rate of 1:6 to 1:12 including cost of all materials such as case hardened worm wheel,Taper roller roller bearings for worm shaft,Thrust roller bearings for worm wheel with cover and all other related acessories, labour and conveyance charges etc. complete but excluding the cost of 63 mm dia screw shaft already supplied.

od9159/2018_2019/MH : Supply of screw shaft 63mm outer dia , head pitch of 12.7 mm root dia 50.3 mm using EN -8 shaft Including cost of all material, labour,tools etc. complete.

85.124 : Fabrication and supply of Hoisting bridge unit in structural steel confirming to IS2062Gr including ladder, covers for hoisting unit etc as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, incidental and handling charges for fixing handrails and allied works etc complete but excluding material already supplied and weight of pipes for hand rails etc

Supply of operating mechanism acessories such as Chain and sprocket etc.complete

od7511/2018_2019/MH : Providing Chain & Sprocket assy. to the manual operating mechanism for the shutter consisit of 2Nos.of sprocket wheel,2Nos.of Plummer blocks,driven shaft,shaft for sprocket wheel,handlever locking arrangements, including the cost of material, cost of machining, hire charge of machineries,tools etc. as directed by the departmental officer at site.

Erection of newly fabricated shutter 1No.along with acessories,hoist platform & its acessories etc.complete.

85.111 : Erection of the gates safely in the grooves , assembling and aligning including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site

85.136 : Erection of the hoisting bridge unit including handrails , ladder and platform etc. in correct alignment and anchoring it ; setting and aligning the covers of the hoisting unit etc complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

Painting the hoist platform and its acessories ,ladder,hand rails etc.complete as directed by the deptl.officers at site.

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

Bidder Name

ASHIFUL HAK.C