COMPLETION OF INCOMPLETE WORK FOR PROVN OF OTM ACCN AT KAKSAR BASE AT KARGIL

Amount

Building work SCHEDULE 'A' PART-I Completion of incomplete/ balance work in Construction of block for 6 Hav and 44 ORs (Double storey) complete all as specified and shown on drawings. Note :- 2400mm wide covered connecting passge as shown on drawings shall be measured and paid separately under serial item No 9 of this schedule.(First Block) (Refer Annexure-I)

Completion of incomplete/ balance work in Construction of block for 6 Hav and 44 ORs (Double storey) complete all as specified and shown on drawings. Note :- 2400mm wide covered connecting passge as shown on drawings shall be measured and paid separately under serial item No 9 of this schedule. (Second Block) (Refer Annexure-II)

Completion of incomplete/ balance work in Construction of block for 6 Hav and 44 ORs (Double storey) complete all as specified and shown on drawings. Note :- 2400mm wide covered connecting passge as shown on drawings shall be measured and paid separately under serial item No 9 of this schedule. (Third Block) (Refer Annexure-III)

Completion of incomplete/ balance work in Construction of block of common and study room, store room (Single storey) complete all as specified and shown on drawings. (Refer Annexure-IV)

Completion of incomplete/ balance work in Construction of block of cook house and dining hall (Single storey) for 24 Hav and 176 ORs complete all as specified and shown on drawings. (Refer Annexure-V)

Completion of incomplete/ balance work in Construction of block of plant room for hot water supply (Single stoery) (84 Sqm) complete all as specified and shown on drawings. (Refer Annexure-VI)

Completion of incomplete/ balance work in Construction of block of Plant room for CHS and Generator room (Single storey) (150 Sqm) complete all as specified and shown on drawings. (Refer Annexure-VII)

Construction of RCC under ground sump of 30,000 ltr capacity complete all as specified and shown on drawings.

Construction of block of Garbage bin with mild steel gate complete all as specified and shown on drawings.

Construction of Soakage well (stone construction) of size 3.0m internal dia and 4.5m deep below inlet pile (depth from inlet pipe to ground level 0.60m) complete all as specified and shown on drawings.

Construction of covered connecting passage 2.4m wide complete all as specified and shwon on drawings.(Note:- Length in parts to connect various block of Sch 'A; Part-I.

Internal Water Supply Works SCHEDULE 'A' PART-II Sch ‘A’ Part-II is prepriced by MES and pre priced rates indicated under Col 5 signifies this fact only. Bidders shall insert their rates in green field under Col 6

Internal Electrification SCHEDULE 'A' PART-III Sec-I Sch ‘A’ Part-III Sec-I is prepriced by MES and prepriced rates indicated under Col 5 signifies this fact only. Bidders shall inserted their rates in green field under Col 6

Internal Electrification SCHEDULE 'A' PART-III Sec-II SCHEDULE 'A' PART-III Sec-II is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Supply and fixing epoxy black powder coated sheet aluminium housing with expoxy white powder coated CRCA sheet steel gray tray, clear acrylic cover, aluminium reflector and accessories complete with 'S' type CFL 2 x18 watts suitable for security light purposes, as specified, including provision of GI bracket of 40 mm bore, bend to shape, medium grade pipe of 1.5 m length for fixing on walls, clamps of flat iron 40 x 6 mm and provision of 2.5 sqmm PVC insulated, sheathed aluminium weather proof cable for making connections complete all as specified.

Supply and fixing energy efficient T-5 fluorescent tube light fitting suitable for and including tube rods of 1 x 14 W, complete with electronic ballasts, capacitors spring loaded rotor type lamp holders starter, connector block, etc, and all accessories pre-wired. Make: Bajaj Cat Part No BJHL 114 T5 SL or equivalent in Crompton Greaves & Philips.

Supply and fixing flame proof fluorescent lamp luminair 1 x 40 Watts complete with all fittings including tube light and making connections with 3 core PVC insulated copper cable of 1.0 sqmm from fitting to ceilling rose, all as specified and directed by Engineer -in- charge.

Supply only CFL 15 watt suitable for holder fitting Make:- Philips/Bajai/ Crompton Greaves

Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 4Sqmm (2 single run) with one continous FRLS copper earthing lead wire of size 2.5 Sqmm and drawn into concealed PVC conduit and conected to common earth dolly, complete and as directed.

Earthing complete with galvanised steel earth plate electrode 60cm x60 cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to GI wire 4.0 mm dia (as earth lead wire), by means of bolts, nuts check nuts and washer of GI and earth wire protected by provision of GI pipe light grade, 15 mm bore including provn of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregates wth 40 mm thick cover of RCC (1:2:4) rainforced with XPM ( weight not less than 4 Kg /Sqm ) and frame of angle iron 25x25x3 mm with lugs 2 Nos and with 6mm dia MS bar handle made to shase, GI light grade 20 mm bore pipe for watering perforatedat bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtr, all as per electrical plate No 5 of SSR1991 Part-I and connection to erath test point all as specified and testing on completion. Note:- Items of Earthing including cost of 7.5 m long galvanised iron earth wire 4.00 mm size and protection pipe of 15 mm bore GI light grade . Any varitation in lenght shall be adjusted through deviation order based on SSR rates adjusted with percentage quoted by the contractor against Sch'A' Prt-III ( Sec-I)

Sub Total

Sewage Disposal SCHEDULE 'A' PART-IV Sch ‘A’ Part-IV is prepriced by MES and prepriced rates indicated under Col 5 signifies this fact only. Bidders shall insert their rates in green field under Col 6

Area Drainage Works SCHEDULE 'A' PART-V Sch ‘A’ Part-V is prepriced by MES and prepriced rates indicated under Col 5 signifies this fact only. Bidders shall insert their rates in green field under Col 6

Road Path and Culverts SCHEDULE 'A' PART-VI Sec-I Sch ‘A’ Part-VI is prepriced by MES and prepriced rates indicated under Col 5 signifies this fact only. Bidders shall insert their rates in green field under Col 6

Road Path and Culverts SCHEDULE 'A' PART-VI Sec-II SCHEDULE 'A' PART-VI Sec-II is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Supply only paving bitumen any penetration for incorporation in road work under Sch 'A' Part-VI Sec-I

Sub Total

Protective Works SCHEDULE 'A' PART-VII SCHEDULE 'A' PART-VII is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Hot Water Supply SCHEDULE 'A' PART-VIII SCHEDULE 'A' PART-VIII Sec-II) is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Supply and fixing 80mm dia MS ERW pipe with Kaiflex insulation tubing of size 89 mm inner dia and 25 mm thick Make:- Kaiflex markedted by carewell pipes, 102 Usha Kiran Building, Commerical Complex Azadpur Delhi/Superion/ Vidia Flex.

50mm dia MS ERW pipe Kaiflex insulation tubing of size 60mm inner dia, 19mm thick.

25mm dia MS ERW pipe Kaiflex insulation tubing of size 35mm inner dia, 19mm thick.

20mm dia MS ERW pipe Kaiflex insulation tubing of size 28mm inner dia, 19mm thick.

20mm dia MS ERW pipe Kaiflex insulation tubing of size 28mm inner dia, 19mm thick.

Earthing complete with galvanised steel earthplate electrode 600mmx600mm thickness not less than 6mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, Connected to and including GI earth load using galvanised iron strip 32mm x 6mm size by means of nuts & bolts, check nuts and washers of galvanised including PCC pit of 1:2:4 type B-1 cover reinforced with XPM weight not less than 4 KG/Sqm and 6mm dia bar handle excavation and earth work in any type of soil, charcoal dust, salt, medium grade GI watering pipe of 20mm dia with funnel and wire mesh and medium grade GI protection pipe of 40mm bore from top edge of earth plate upto main distribution baord complete all to as shown in electrical plate No 3 of MES Sch 2009 connected main switch board all as specified and testing on completion. Note:- Item of Earthing includes cost 7.5m long galvanised iron earth strip 32x6mm size and protection pipe of 40mm bore GI medium grade. Any variation in length shall be adjusted with Note No 4 Schedule 'A' Notes.

Sub Total

External Electrification SCHEDULE 'A' PART-IX Sec-I Sch ‘A’ Part-VIII Sec-I is prepriced by MES and prepriced rates indicated under Col 5 signifies this fact only. Bidders shall inserted their rates in green field under Col 6

External Electrification SCHEDULE 'A' PART-IX Sec-II SCHEDULE 'A' PART-VIII Sec-II) is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Only installation, testing and commissiong of diesel engine/driven generating set of capacity 100 KVA, 415 Volts, 0.8 PF, at NTP, mounted on base plateform with flexible coupling, 1500 RPM alongwith sound proof enclosure (Acoustic enclosure) designed for reducing the sound level to 7 ± 5 of B (A) (average) IS 8528 Part-10 as per approved CPCB norms and as per GSR 371 (E) dated 17.05.2002 with silencer pipe and silencer muffler coverd with asbestos rope 25 mm thick independently supported from engine to outside of power house upto 1 mtr, cold start kit, battery start with suitable size of stardrad cables for connecting from DG set to panel board DG set shall be capable with and including the follwing:- (A) Prime Mover :- Diesel engine of suitable of capacity water cooled radiator mounted) closed circuit as per BS-649 or IS-1002 direct injection type with turbo charger.Make :- Cummins India Ltd/Kirloskar. The diesel engine shall be capable of runing 24 hrs continuously with 10% overloading for one hrs in every 12 hrs as per BS-5514/BS 649. Engine shall be equipped with all standard fittings as per manufactures. Recommendations mounted on common base plate/ form thorgh flexible coupling with :- (Item shall be provided under Sch A Part-XVI :Sch of Credit (Old contractor's store and T&P or incorporation in the work)-Refer 88-A (Revised)

(A) (a) RPM Cum hours meter. (b) Battery charging ammeter (c) Ignition key and starting with push button swtich (d) Lubricating oil pressure gauge (e) Electronic governor controlling. (f) Toggle switch for idile running (g) Oil temp gauge (h) Water Temperture gauge (j) Safety controlled trip for the following:- (i) High water temp (ii) Low lubricating oil pressure (iii) Over speed. (k) Lubricant oil heater to avoid freezing. (l) 24 Hours starting equipment comprising of the following:- (i) 2 Nos 12 V , 180 AH 25 plates battery Make-Exide) (ii) Battery charging alternator with inbuilt regulator (iii)Starter motor of suitable capacity (iv) Battery leads (copper stranded cable ) of suitable of size with brass thimbles and terminal. Make of Engine : Kiroskar/Cummins (B) ALTERNATOR:- Alternator of capacity 200 KVA/160 KW at NTP, 415 Volts, 50 C/S, 1500 RPM, 0.8 PF self excited, self regulated screen protected with self excited field brush rotating fixed designed to be coupled with above engine thorgh flexible coupling . The alternator shall be conformed to 4722 of BS-2613 Make -Kiroskar/Jyoti/Crompton/NGEF/Stamford.

(D) OTHER FITTINGS:- (a) Battery Charger :- Battery Charger having electric circuit consisting of rectifiers, capacitiors and resitance etc. The battery charger should be able to charge 12 volts 180 AH battery 2 Nos at a time (b) Fuel tank of suitable capacity as per manufactures recommendation mounted on steel frame at suitable height with all connecting pipes and fittings upto fuel pump and over flow pipe from engine to tank including level indicating gauge duly marked and drain and air vent plug etc.

(E) Maintenance Spares:- (i) Fuel filter elecment-02 No (ii) Oil filter elements -03 No (iii) Fan belt-01 Set. (iv) Hose pipe -01 No (v) Tappet cover gasket -01 No (F) DG set shall be supplied alongwith acoustic original enclosure of the manufacture's suitable for 200 KVA DG set as per CPCB Norms. Note for item No. 11.01 to 11.05 :- (i) Shifting of DG Set from one location to another location as directed by Engr-in-charge, servicing, tophing up of engine oil, coolant, replacement of filters (if required), any other spare parts/accessories are deemed included in overall cost quoted by contractor. (ii) Bidders are advised to visit he site and ascertain the serviceability and quantum of repairs to get the above equipment serviceable.

Earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm thickness not less than 6mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of plate not less than 1.5 mtr below normal ground level, connectted to and includig GI earth load using galvanised iron strip 32 mm x 6mm size by means of nuts & bolts check nuts and washers of galvanised including PCC pit of 1:2:4 type B-1 cover reinforced with XPM Weight not laes than 4 Kg /Sqm and 6mm dia bar handle, excavation and earth work in any type of soil, charcoal dust, salt, medium grade GI watering pipe of 20mm dia with funnel and wire mesh and medium grade GI protection pipe of 40 mm bore from top edge of earth plate upto main distribution board complete all to as shown in electtrical plate No 3 of MES SSR 2009 (Part-I) connected main swtich board all as specified and testiing on completion. NOTE:- Item of earthing including cost of 7.5 long galvanised iron earth strip 32x6 mm size and protection pipe of 40 mm bore GI medium grade . Any variation in length shall be adjusted with quoted percentage of sch 'A' Part IX ( Section -I)

Supply , installation , testing and commissionig LT panel board out door type platform mounting factory made totally enclosed dust vermin proof double & shutter front & rear opening with locking arrangement made of 16 SWG MS sheet, shutter opened both side duly painted with two coat of synthethic enamel paint, over a coat of red oxide primer paint with angle iron frame 50x50x6mm thick with necessary foundation, nuts & bolts. Panel shoud complete with insulated copper conductor/ PVC sleeve on bus bars with following accessories are as shown below :- (a) Copper bus bar cap , 300 Amps rating on insulator -01 No (b) Amps meter to 300 Amps -01 No (c) Voltmter 0 to 500 volts -01 No (d) MCCB 300 Amps - (4 Pole) -01 No (incoing) (e) MCB TPN 63 Amp -06 Nos ( Outging)

Supply, installation, testing and commissioing of LT panel board indoor type platform mounted factory made totally enclosed dust vermin proof front door & wear opening with locking arrangement made out of 16 SWG MS sheet consisting with the following :- (a) Copper bus bar capacity 300 Amps mounted on insulator -01 set (b) Amp meter-0-300 Amps -01 No (c) Voltmeter 0- 500 volt -01 No (d) MCCB 300 Amps 4 Pole -02 Nos (e) Change over switch 200 Amps 4 Pole -01 No

Street light fitting HPSV 70 watts, single piece, cast aluminium housing (IP- 65) with POT optics reflector including sodium vapour lamp 70 watts complete with all accessorries prewired including provision of bracket of 40mm bore GI light grade pipe made to shape over all length 1.50 meter with clamps of FI 40 X 6mm for fixing street light fiting and providing PVC insulated conductor cable of suitable size for making connection to light fittings from junction box complete all as specified. Make : Crompton Greaves Cat Part No SSG 2107 IH/WI with lamp type 70W HPSV (T) of equivalent in Bajaj/Philips.

Sub Total

External Water Supply SCHEDULE 'A' PART-X Section-I Sch ‘A’ Part-X is prepriced by MES and prepriced rates indicated under Col 5 signifies this fact only. Bidders shall inserted their rates in green field under Col 6

External Water Supply SCHEDULE 'A' PART-X Section-II SCHEDULE 'A' PART-X is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Supply & fixing monoblock pump set suitable for operation at 440V, 50 Hz, 3phase supply with head not less than 30 meter of capacity 5 HP. Make:- Kirloskar/ Crompton Greaves.

Supply, installation, testing and commissioning of LT panel board indoor type platform mounted factory made totally enclosed dust vermin proof front door & wear opening with locking arrangement made out of 16 SWG MS sheet consisting with the following:- (a) Coper bus bar capacity 100 Amps mounted on inslator -01 set (b) Amp meter 0-50 Amps alongwith CTs-01 No (c) Voltmeter 0-500 volt-01 No (d) MCCB 100 Amps , 35 KA-01 No (e) Fully automatic star delta starter suitable for 5 HP , 3 Phase motor - 02 Nos.

Supply and fixing gun metal foot valve with synthethic rubber 'O' ring screwed female and BSP tested 300 PSD, HYD of size 50 mm dia . Make : Sant/Bir

Earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm thickness not lass than 6mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level, connectted to and includig GI earth load usng galvanised iron strip 32mm x 6mm size by means of nuts & bolts check nuts and washers of galvanised including PCC pit of 1:2:4 type B-1 cover reinforced with XPM Weight not laes than 4 Kg /Sqm and 6mm dia bar handle, excavation and earth work in any type of soil, charcoal dust , salt, and medium grade GI watering pipe of 20mm dia with funnel and wire mesh and medium grade GI protection pipe of 40 mm bore from top edge of earth plate upto main distribution board complete all to as shown in electtrical plate No 3 of MES Sch 2009 (Part-I) connected main swtich board all as specified and testiing on completion. NOTE:- Item of earthing including cost of 7.5m long galvanised iron earth strip 32x6 mm size and protection pipe of 40 mm bore GI medium grade. Any variation in lenght shall be adjusted with quoted percentage of sch 'A' Part-X ( Section -I)

Sub Total

Refrigeration and AC Works SCHEDULE 'A' PART-XI SCHEDULE 'A' PART-XI is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Supply and install refrigerator, electric driven (single phase) capacity 310 ltrs. Make : LG/Samsung/Godrej/Whirlpool.

Supply and install deepfreezer hard top 200 liters capacity having single door. Make : Bluestar / Voltas/ Godrej.

Supply and install automatic voltage stablizer suitable for opernation at 230 V, 50 Hz AC supply of capacity 1 KVA including time delay arrangment. Make : Johanson/Blue bird/ Blue line/Electricfield Co.

Sub Total

Central Heating System (SCHEDULE 'A' PART-XII ) SCHEDULE 'A' PART-XII Sec-II is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

All as per item No 15.01 above but of capacity 3,00,000 K cal/hr at MSL

Supply, installation, testing and commissioning of monoblock certrifugal pump having, stainless steel impeller driven by suitable capacity electric motor for ethylene glycol of 520 LPM and 25 metre head complete with accessories and insulated with two layers of 13 mm thick closed cell elastomeric insulation including plain cement concrete foundation as recommended by manufacturer, all as specified.

Supply, installation, testing and commissioning of monoblock certrifugal pump wth bronze impeller, driven by suitable capacity electric motor for glycol fluid make up and mixing complete with accessories suitable for flow rate of 5 LPM and 5 metre head including cement concrete foundation as recommended by manufacturer, all as specified.

Supply and installation of mild steel flue gas chimney made out of 3 mm thick mild steel sheet, minimum 1.20 metre above the hightest pont of the building roof and including connection from boiler to main chimney including shut of damper fabricated from 3 mm mild steel sheet . The portion of the chimney/ flue gas connection inside the building shall be covered with 50mm thick resin bonded fibre glass insulation wool of 24 kg/m³ density and cladded with 26 gauge aluminum cladding all as specified. Note:- (i) The item shall be complete with the mounting/ fixing arrangment. (ii) The genertors shall be connected to a independent chimney.

Rotational moulded polythlene (HDPE) expansion tank of capacity 1500 ltr (Cylinderical verticaln with colsed top) hoisted and fixed in position all as specified in MES SSR Part--I complete coverd with 13 mm closed cell electrometric insulation complete with removal lid, in, out, drain, over flow system, including mounting arrangement and complete connection, all as specified

Rotatinal moulded polythlene (HDPE) glycol fluid storage tank of capacity 1500 ltr (Cylinderical vertical with colsed top) hosisted and fixed in position all as specified in MES SSR Part--I complete with removalable lid, in, out, drains, overflows system, mounting arrangement and complete connection, all as specified.

Supply, installation, testing and connecting with the system and commissioning of horizontal cylinderical oil storage tank made out of mild steel as per IS-2062 and fabricated as per IS 10987-1992 design temprature 30˚C and desgin pressure atmophasre + static head of liquid. (i) Storage capacity (Nominal) : 5 KL (ii) Gross capacity (not exceeding) :5.2 KL (iii) Shell thickness :3mm (iv) End plate thickness : 4 mm Note: - Tank shall be complete with all nozzles, manhole, lifting lugs, vent pipe suitable dia inlet, outlet and return pipes with flanges as per specifications including civil works for installations and staging as per drg.

Supply, installation, testing and commissioning of kerosene oil/ HSD oil day service tank rectangular mild steel construction with capacity 990 liters complete with inlet, outlet, drain and the tank shall be made out of 3mm mild steel sheet and will be provided with supports made out of minimum 50 mm NB class 'B' pipe to keep tank base at minimum (1000 mm) above finished floor level complete, all as specified. Note:- Tank shall be complete with all nozzles, manhole, lifting lugs, vent pipe suitable dia inlet, outlet and return pipes with flanges as per specifications including civil works for installations and staging as per drg.

Supply , installation, testing and commissioning of Rotary gear transfer pumps (self priming type) for capaity 15 LPM, 10 metre head, for Kerosene oil/ HSD oil complete with base frame, foundation bolts, coupling and coupling guard and TEFC FP motor (2 HP), and other accessories required for commissioning (1 working + 1 standby) all as specified.

Supply, installation, testing and commissioning of mild steel/PPR pipe including bends, reducers, flanges, nuts, bolts etc, complete in all respects of following sizes:-

(a) 40 mm bore pipe

(b) 25 mm bore pipe

(c) Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of size 25 mm bore

(d) Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of size 40 mm bore

(e) Non return valve, brass, high pressure, complete, screwed for iron pipe or brass ferule and fixed of capacity 25 mm bore.

(f) Y- oil strainer of size 25 mm bore

Supply and laying, connecting, fixing and testing of mild steel ERW, class 'C' piping complete with fittings, duly insulated with closed cell elastomeric instalation 30 to 40 Kg/m³ density covered with shrink wrap polythene sheet for the following sizes of Hot Glycol fluid pipes:- Note:- The pipes exposed to atmosphare or buried under ground will be insulated with below mentioned thick insulaton.

(a) 150 mm bore pipe with 16 mm thick nitrile insulation

(b) 125 mm bore pipe with 16 mm thick nitrile insulation

(c) 100 mm bore pipe with 16 mm thick nitrile insulation

(d) 80 mm bore pipe with 16 mm thick nitrile insulation

(e) 65 mm bore pipe with 13 mm thick nitrile insulation

Supply and first fill for makeup requriement for the first year of operation of glycol concentrate along with the necessary additives and inhibitor in congnition and supplied in barrels. The mixture freezing tempreture should be (-40˚C), all as specified.

Supply and laying, connecting, fixing and testing of poly propylene random copolymer aluminium foiled pipes or composite pipes complete with fittings duly insulated with 13 mm thick closed cell elastomeric insulation 30 to 40 Kg/m³ density for the following sizes of Hot Glycol fluid pipes:-

(a) 63 mm bore OD pipe

(b) 50 mm bore OD pipe

(c) 40 mm bore OD pipe

(d) 32 mm bore OD pipe

(e) 25 mm bore OD pipe

(f) 20 mm bore OD pipe

(g) Butter fly valves 100 mm dia

(h) Butter fly valves 80 mm dia

(j) Dual plate Non return valves 100mm bore

(k) Ball valves 25mm bore

(l) Balancing valves 100mm dia

(m) Balancing valves 80mm bore

(n) Balancing valves 65mm bore

(o) Inlet/Outlet valves for FCU's

(p) Pressure gauges with cocks and siphon

(q) Water flow switch

(r) Automatic air puuging valve

Supplying, installing, testing and commissioning of decorative wall mounted fan coil units complete with top grill, side panels, 3 speed motor thermostat, wall mounting brackets inlet outlet manifold and finished with polyester finishing coat for superior finesh complete all as specified of following sizes:- (a) 4500 Kcal/hr

Supplying, fabricating and installing perforated mild steel cable trays of size 150 mm width x 50 mm depth including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceilling with mild steel suspenders and including painting two coats synthetic enamell paint over a coat zinc chrome paint, all as specified and directed. (For cabling work in plant room)

Supply and fix 6 SWG dia GI wire on surface of in recess for loop earthing inter connecting main panel and other electrical equipment.

Providing ''No Smoking'' and '' Flammable'' sign board as per requirement of petrolium Rules and CCOE Nagpur , all as specified

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less tham 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to the Galvanised iron earth lead 32x 6mm size, by means of bolts, nuts, check nuts and washers of galvanised iron and 32x 6mm lead protected by provision of GI medium grade pipe 40 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 meter long placed on top edge of earth plate, common salt and charcoal filling, test point made out of bronge/gun metal with fixing arrangement, funnel wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No-03 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- Item of Earthing includes cost of 7.5m long galvanised iron earth lead 32x6mm size protection pipe of 40mm bore GI medium grade. Any variation in length shall be adjusted through deviation order based on SSR Rates adjisted with percentage as per Note No 4 of Schedule 'A' Notes here-in before

Supply only PVC insulated and sheathed (ISI marked) copper multistrand conductor, armoured cable of 1.1 KV grade confirming to IS-1554 of size 3 x 6 Sqmm all as specified.

Supply only PVC insulated and sheathed (ISI marked) copper multistrand conductor, armoured cable of 1.1 KV grade confirming to IS-1554 of size 3 x 4 Sqmm all as specified.

Supply only PVC insulated and sheathed (ISI marked) copper multistrand conductor, armoured cable of 1.1 KV grade confirming to IS-1554 of size 2 x 4 Sqmm all as specified.

Provision of display board (Notice board) 1200 mm x 900 mm as per drg No CESZ/TD-175/95 sheet 1/1 for displaying and including resusciation chart in three languages for electric shock and burn injury complete, all as specified and directed.

Sub Total

EXCAVATION AND EARTH WORK FOR SCH 'A' PART-II TO PART-XII SCHEDULE 'A' PART XIII Lump sum price worked out by the Contractor for “Earth Work” as listed in Schedule ‘A’ Part- XIII

DEFECTIVE WORKS SCHEDULE 'A' PART-XIV SCHEDULE 'A' PART-XIV) is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6. Item No 1.00 to 1.03 & 1.05 i.e. Construction of block for 6 Hav and 44 ORs (Double storey) (Block I, Block II, Block III), construction of block of common and study room, store room (Single storey) and Block of Plant room for hot water supply (84 Sqm). Details of each block attached separately in the tender as Appx "A".

Taking down Cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, finishing even and smooth without using extra cement on brick/concrete complete all as specified and as directed

M & L rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces, finishing even and smooth without using extra cement on brick/concrete complete all as specified and as directed

Demolition of cement in Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M&L for 75mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) as in subbase, floors and paving complete all as specified and directed.

Demolition of cement in Concrete reiforced (reinforcement cut as required to facilitate demolition) of any description and in ant position not othewise specifically provided for.

M&L for Providing Reinforced Cement concrete design mix M-30 using 20 mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Mild steel bars 5mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Sub Total

RETROFITTING WORKS SCHEDULE 'A' PART-XV SECTION I TO V SCHEDULE 'A' PART-XV) is prepriced by MES (SSR-2020) and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

Retrofitting to blocks (Block-I, Block-II and Block-III) for 6 Hav and 44 ORs (Double storey) complete all as specified and shown on drawings.

Retrofitting to block of common and study room, store room (Single storey) complete all as specified and shown on drawings.

Retrofitting to block of cook house and dining hall (Single storey) for 24 Hav and 176 ORs complete all as specified and shown on drawings.

Retrofitting to block of Plant room for CHS and Generator room (Single storey) (150 Sqm) complete all as specified and shown on drawings.

Retrofitting to block of plant room for hot water supply (Single stoery) (84 Sqm) complete all as specified and shown on drawings.

RETROFITTING WORKS SCHEDULE 'A' PART-XV (SECTION-VI) SCHEDULE 'A' PART-XV) is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only. Bidder shall insert their rates in Green field under column-6.

M&L for Removal of loose /soft concrete layer and preparation of rough bonding surface in columns and beams complete all as specified and directed.

M&L for Providing and fixing of 8 mm mechanically drilled dowel bars, 100 mm depth and bounded with epoxy grout for columns and beams complete all as specified and directed.

M&L for Providing and fixing Steel wire mesh 75 mm x75mm of dia 3 mm, hard drawn (proof stress 0.2% minimum of 480 N/mm2) confirming to IS 1566: 1982 and IS 432 (Part-II) 1982 complete all as specified and directed.

M&L for 25 mm thick cement concrete shortcrete of M30 grade confirming to IS 9012 : 1978 (reaffirmed 2021) for exterior beams at plintth and floor levels complete all as specified and directed.

M&L for 50 mm thick cement concrete shortcrete of M30 grade confirming to IS 9012 : 1978 (reaffirmed 2021) for column retrofitting complete all as specified and directed.

M&L for Providing structural steel of Grade E-250 (minimum yield strength of 250 N/mm2 and ultimate tensile strength of 410 N/mm2 confirming to IS 2062: 2011), including cutting, hosting, fixing in position by using fillet/Grove welding complete, and applying a priming coat of approved steel primer / anti-corrosive coat (Redoxide zinc chrome primer confirming to IS 2074: 2023), etc. including each column corner angle fixed with epoxy resin impregnation for steel to concrete bonding complete job.Used size as per NIT drawings:- Size 200x6 mm battens, 50x6 mm battens ISA 40X40X5 mm, ISA 50X50X5 mm, ISA 50X50X6 mm & ISA 65x65x6 mm,10 mm thick base plate etc and any size if required.

M&L for Providing and fixing Anchor Bolts M 12x250 (12 mm dia and 250 mm long) of Grade 5.8 confirming to IS 1946 (Part II): 2025. The anchor should possess ETA certificate for use in cracked concrete approved as per seismic condition for fixing steel bearing plates with the concrete foundation, Plinth beam ,floor and roof beam including epoxy grouting, mechanical drilling, etc. complete Job. (Make of Anchor and Resin Epoxy:- Hilti, Fischer, Mungo, Rawlplug). Note 1:- Execution to be done by company authorised applicator with prior similar experience and mandatory on site test (Pull out test) as per standard frequency and load given by OEM. Note 2:- Resin Epoxy product should be approved by ICC, CSTB, COLA, BZS with shock approval,Fatigue and fire approvals. The chemical should have an ETA approval for 100 years agetesting. Drilling hole with appropriate drill bits to the required depth by rotaryhammer drill, cleaning with brush and jet of clean air to ensuredust free clean holes and proper bonding of chemical, filling resin and hardener using serrated nozzle toeliminate mixing error with standard HDE A22 battery dispenser along with piston plug.

M&L for Providing and fixing Anchor Bolts M 10x100 (10 mm dia and 100 mm long) of Grade 4.6 confirming to IS 1946 (Part II): 2025. The anchor should possess ETA certificate for use in cracked concrete approved as per seismic condition for fixing steel bearing plates with the concrete foundation, Plinth beam ,floor and roof beam including epoxy grouting, mechanical drilling, etc. complete Job. (Make of Anchor and Resin Epoxy:- Hilti, Fischer, Mungo, Rawlplug). Note 1:- Execution to be done by company authorised applicator with prior similar experience and mandatory on site test (Pull out test) as per standard frequency and load given by OEM. Note 2:- Resin Epoxy product should be approved by ICC, CSTB, COLA, BZS with shock approval,Fatigue and fire approvals. The chemical should have an ETA approval for 100 years agetesting. Drilling hole with appropriate drill bits to the required depth by rotaryhammer drill, cleaning with brush and jet of clean air to ensuredust free clean holes and proper bonding of chemical, filling resin and hardener using serrated nozzle toeliminate mixing error with standard HDE A22 battery dispenser along with piston plug.

M&L for Providing and fixing threaded bolts / shear connectors (M8x125) of 8 mm dia and 125 mm anchorage length of Grade 4.6 confirming to IS 1946 (Part II): 2025. The anchor should possess ETA certificate for use in cracked concrete approved as per seismic condition for fixing batten plates to existing concrete columns and beam, including mechanical drilling and use of epoxy grout in the drilled holes, complete job. (Make of Anchor and Resin Epoxy:- Hilti, Fischer, Mungo, Rawlplug). Note 1:- Execution to be done by company authorised applicator with prior similar experience and mandatory on site test (Pull out test) as per standard frequency and load given by OEM Note 2:- Resin Epoxy product should be approved by ICC, CSTB, COLA, BZS with shock approval,Fatigue and fire approvals. The chemical should have an ETA approval for 100 years agetesting. Drilling hole with appropriate drill bits to the required depth by rotaryhammer drill, cleaning with brush and jet of clean air to ensuredust free clean holes and proper bonding of chemical, filling resin and hardener using serrated nozzle toeliminate mixing error with standard HDE A22 battery dispenser along with piston plug.

M&L for Providing application of crack seal between structural steel sections (battens, angle sections, etc.) and existing concrete of suitable make for filling gaps and inject epoxy adhesive by using perfusion application, complete job for retrofitting of columns.

Sub Total

Schedule Of Credit SCHEDULE 'A' PART-XVI SCHEDULE 'A' PART-XVI)Schedule of Credit ( Old Contractors Store For Incorporation in the Work) (Rs 8,76,813.56)

m/s lago constructions (BID ID -3455550)

M/S ABDUL SALAM MIR CONSTR CO PVT. LTD (BID ID -3460444)

shitapa traders (BID ID -3459716)