cafeteria hall at museum

Demolishing and disposal of unserviceable materials within 100 metres lead. Unreinforced cement concrete up to 15cm thickness

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead. Brick work

Conveyance of excavated surplus earth/debris to a distance 2 kms from the site of work at the place specified by the Engineer-in-Charge including loading and unloading etc., complete as directed during execution.

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. Ordinary soil-MECHANICAL means up to 3m depth

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Cement Concrete (1:4:8) using 40 mm ( 0.54 cu.m), 20mm (0.27 cu.m) and 12 mm (0.09 cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5)-Grade M15 using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC)etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department but incuding cost of centering, shuttering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402). Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kgs/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

For Columns footings

For Columns Pedastals

For Columns in First floor

For Columns in Second floor

For Columns in Third floor

For plinth beams

For lintel beams in First floor

For lintel beams in Second floor

For Roof beams in First floor

For Roof beams in Second floor

For Roof beams in Third floor

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC)etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department but excluding cost of centering, shuttering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402). Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kgs/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

For Roof slab First floor

For Roof slab second floor

For Roof slab Third floor

Supply and placing of the M20 Design Mix using of 10mm HBG crushed metal 0.480cu.m,6mm HBG Crushed metal 0.320cu.m,sand 0.400cu.m and cement 350Kgs with water cement ratio of 0.53(185.50 ltrs/cu.m of CC) etc., from any source confirming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, centering charges, shuttering charges for finished item of work (APSS No. 402)

- do - for precast slabs 50 mm thick using 10 mm graded aggregate HBG crushed metal from any source conforming to the relevant ISI standards, with necessary reinforcement excluding cost of steel and tying of grills, centering charges,but including cost of necessary form work etc., complete as directed by the department.

RCC M- 20 Design mix using 20mm HBG crushed metal 0.480 cu.m , 10mm HBG crushed metal 0.320 cu.m , sand 0.400 cu.m and cement 350 kgs with water cement ratio of 0.53 (185.5 Lit per cu.m of CC ) etc. horizontal plain sunshades or lofts projecting from the face of the wall 65mm average thickness,80mm thick at the face of the wall and 50mm thick at the free end and cast monolithically with the lintels or tailed to the full thickness of the wall where there are no lintels using 20mm size graded machine crushed hard granite metal (coarse aggregate) from any source conforming to the relevant ISI standards including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing , etc.,complete, but excluding cost of centering charges and excluding cost of steel and its fabrication charges for finished item of work.

do in First floor

do in Second floor

Centering charges for centering & scaffolding unsupported height up to 3.66m- steel scaffolding pipes, jack props, wallers, Foot plates, brackets, steel centering plates, etc. Second floor

In First Floor, Slabs up to 150mm thick

In Second floor, Slabs up to 150mm thick

In Third floor, Slabs up to 150mm thick

Providing high yield strenth Deformed bars (HYSD)/ Thermo Mechanically Teated (TMT) bars steel bars ( Fe-500 grade as per IS 1786-1979) of different dia metres for RCC works, including labour charges for strengthen, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18sWG, forming grills for reinfocement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all flors. (APSS No. 126) - below 36mm Fe 500 grade

Construction of Brick Masonry in CM (1:6) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm)including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

-do-up to basement

In Second Floor

Construction of 110 mm thick Brick partition walls in CM (1:4) using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc,. Complete.

In Second Floor

Plastering in C.M(1:5) 20 mm thick using best river sand including cost and conveyaynce of all materilas screening curing rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

In Second floor

Plastering in C.M(1:5) 12 mm thick using best river sand including cost and conveyaynce of all materilas screening curing rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

Plastering in C.M(1:3) 12 mm thick using best river sand including cost and conveyaynce of all materilas screening curing rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

In Second floor

Supplying and fixing in position Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 35 mmthick conforming to IS:2202 of standard make with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, Single leaf using Best Indian Teak wood frames of size 75mm x 100mm without threshold plate, including cost of M.S "Z" Hold fasts of 230 x 50 x 6mm, M.S Powder coated Butt hinges of 125 x 65 x 2.12mm, screws, nails, etc., complete, (excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (whitepowder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at allcorners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted. But no extra payment on this account shall be made.

Three track three panels sliding window with fly proof SS wire mesh(Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing factory made uPVC white colour fixed glazedwindows / Ventilators comprising of uPVC multichambered frame andmullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),uPVC extruded glazing beads of appropriate dimension, EPDM gasket,G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plasticpackers, plastic caps and necessary stainless steel screws etc. Profileof frame shall be mitred cut and fusion welded at all corners, mullion (ifrequired) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap betweenframe and adjacent finished wall shall be filled with weather proof siliconsealant over backer rod of required size and of approved quality, allcomplete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes and silicon sealant. Note: For uPVC frame, sash and mullion extruded profiles minus 5%tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted. But, no extra payment on this account shall be made. Fixed windows / Ventilators made of (small series) frame 47 x 50mm & mullion 47 x 68 mm both having wall thickness of 1.9 ±0.2 mm and single glazing bead of appropriate dimension

Painting two coats with Ready mixed Synthetic Enamel paint in all shades Grade-I having VOC (Volatile Organic Compound) content less than 50 grams/liter and over a primary coat wood primer (Total 3 coats) approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete. New wood work.

Flooring with vitrified tiles of 1st quality of Double charged (with double layer pigment) / multi charged stain free full body (with homogeneous full body pigment for entire body thickness) porcelain vitrified tiles of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs of series and shades set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & joints with spacer joints with 3 mm wide jointed neatly with filer material of cement/epoxy grout/white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials, etc., complete - for finished item of work. (Note: Unless otheruise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Flooring the following granite salbs set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work.

Leather finish camel brown granite 16 to 18 mm thick slabs up to 8'-0" (2.43m)

Flooring with granite slabs set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the slabs against supply)

Galaxy granite 18-20mm thick upto 8'"-00(2.43m)(Premium quality)

Providing and applying wall putty of white cement or polymer or cement based putty of approved/standard make with average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2-3 hrs. sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work, excluding scaffolding charges - for internal and external walls. for new work

Painting two coats for new work with Acrylic Emulsion paint over a primary coat (water Thinnable) (Total 3 coats) exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for external walls.walls.

Painting two coats for new work with Acrylic Emulsion paint over a primary coat (water Thinnable) (Total 3 coats) interior grade having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls.

Supply of Rabbit wire mesh (G.I. Chicken mesh) of not less than 24 gauge

Providing weather proof course with Screeding concrete in CC(1:2:4), 25mm average thickness using 6 to 10mm nominal size HBG crushed metal chips, screeding duly embedding 24G chicken mesh with necessary overlap etc.., and finishing the surface neatly and rounding the edges at parapet walls, columns etc.., excluding cost of chicken mesh but including cost and conveyance of all materials etc., complete as directed during execution.

Providing impervious coat to exposed RCC roof slab surface with CM (1:3), 20mm thick with 500 ml of liquid concentrated micronized cement water proof compound complies with IS:2645-2003 of approved make per 50 kg bag of cement laid over roof when it is green including cost of all materials, conveyance charges of materials and all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., complete for finished item. third floor

Providing Unplasticized PVC SWR Rain water downfall pipes 110 mm dia PVC pipe with wooden block of size 150mmx50mmx50mm with ISI:13592 Type -A mark with necessary shoes, bends, collars etc., including making holes in walls, RCC slabs, beams, columns, including fixing with necessary wooden plugs (where it is required pipe clear of wall, wooden blocks of size equal to that of ears of the pipe shall be used), screws, iron clamps of 18 G and making good the same including cost and conveyance of all materials and incidental charges etc., complete as directed during execution.

Providing and laying water proofing cum heat insulation treatment with Home Shield Polurethane (PU) Roofkoat (Berger or equivalent) over existing roof slab, all as directed by Engineer-in-charge and as per the following specification:

Surface Preparation

1.Clean the Surface thoughly to make it smooth and free of any foreign material 2.Water pounding test for Mother slab to identify the leakages points before starting the water proofing treatment work 3.Injection grouting should be done for all leakages point indentified and inject the cement slurry dmixed with injection grout admixture, using pressure grouting machine till the rejection of material from the nozzle. 4.Reparing od construction joints by chasing with cutting machine and fill the same with polymerized mortor in C.M91:4) admixture with Advanced Latex plus as per the specified company instructions.

Water proofing Application with PU Roofkoat

1. Apply a self-priming coat of PU Roofkoat after diluting with clean water @50%(1:0.50) 2.Allow to dry for 4 to 6 hours 3.Ally 1st coat of PU roofkoat [email protected] per sqm 3.Allow to dry for 4 to 6 hours 4.Apply 2nd caot of PU roofkiat wuithout dilution @ 0.40Kg per Sqm

The cost inclusive of all required materials such as Home Shield Polurethane (PU) Roofkoat (Berger or equivalent),Injection goruting with required materials, reparing construction joints with required materils and all labour charges for above activities etc., complete as directed during execution.

Supply, fixing and Painting of MS tubes & Pipes of all diametres as per IS-1161 inlcuding cost and conveyance etrc complete as directed during the execution of the work. Including Labour charges for fabricating steel works like Trusses, Stanchions, Heavy Beams and Girders including cost of welding rods, power charges including cost of fixing in position. including painting the grills with two coats over a primary coat (total three coats) with synthetic enamel paint of approved make and colour etc., complete

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply and fixing of stainless steel SS-304 grade tubes, sections, plates , sheets and pipes of all sizes and diameters etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using SS welding rods including buffing , polishing , lacquer finishing , to present seamless finishing etc., complete as directed during execution

Supply and fixing Aluminium Aldrops sliding door bolts 16mmx 300 mm

Supply and fixing of Anodised Aluminium Door handles IS 208. 150mm long

Supply and fixing of Anodised Alunminium tower bolts 12mm dia with ISI Mark IS 204 (pt-II) 1978 12x200 mm long.

Supply and fixing of Heavy Duty Aluminium Door stopper

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness (Total Coated Thickness-TCT), Coating: Alu Zinc coating AZ150 GSM. Tensile strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc., complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame.

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.

--do-- Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Supplying and Fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-1973 of Hind ware/ Parry ware make white glazed with 'P' or "S" trap

Supply & fixing of PVC low level cistern parry ware, slim line with internal components & short bend: 10 Litres capacity Single Flush

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996

Supply & Fixing of Bibcock cum Health Faucet with 1m long tube and wall hook of Jaguar Florentine (quarter turn) series, Chrome Finish with 7 years warranty.

Supply & Fixing of Angular stopcock with wall flange Jaguar Florentine (quarter turn) series, Chrome finish with 7 years warranty

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality confirming to IS:2556-Part-4:1972 with ISI mark or equivalent approved by the department, with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread confirming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams complete with standard CI brackets including wooden block. 550 x 400 mm - Single C.P. Pillar cock

Supply & Fixing of towel rail 24" Jaguar Continental series, Ivory gold colour with 7 years warranty

Supply and Fixing of Ashirvad / Ajay / Astral Flowgurard or equivalent CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" Ashirvad Flowgurard SDR 13.5 pipes are made from identical CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007)

54.00 mm OD pipe SDR - 13.50

28.60 mm OD pipe SDR - 13.50

22.20 mm OD pipe SDR - 13.50

Supplying and fixing Gunmetal Gate (GM peet) valve as per IS - 778 Class-I, Indian make heavy type - 50 mm nominal bore size.

Supplying and fixing Gunmetal Gate (GM peet) valve as per IS - 778 Class-I, Indian make heavy type - 25 mm nominal bore size.

Supply of round Jali

4" (101.6mm) Nahany Trap [without inlet & jali] UPVC/ SWR pipe fittings [prince/ Sudhakar or any ISI Brand]

Supplying, laying and jointing in position the following dia metre of Prince / Sudhakar make or equilent quantity PVC/ SWR pipes 6Kg/sqcm including labour charges for laying, fixing and commissioning the PVC pipes including couplers/ bends/ tees etc., including fixing necessary fittings like bends, plugs, couplers, junctions, tees, etc., with solvent jointing as per standard practice as directed during execution.

160mm dia pipe double Socket

do 110 mm dia single socket pipe

do 75 mm dia single socket pipe

Supplying & Fixing white glazed flat back half stall urinals 1st quality confirming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm confirming to IS:2556 - Part 6, Sec-6-1974 fixed with screws complete Indian make with ISI mark or equivalent approved by the department, of urinal size 590 x 375 x 390 mm

supply & fixing NP soap dish heavy type with NP Screws as directed during execution.

SYMET 2 in 1 Faucet (1 mts tube ) with hook ( as per prayag make CAT NO 187) as directed during execution

supply and fixing 12.7mm brass stop cock Indian make heavy duty 400 grams

supply and fixing 12.7mm heavy duty dia high neck pillar cock 1st quality Indian make 400 grams

Manufacture as per BIS:12592 (Part 1&2) Supply & Delivery of manhole covers and frames with ISI marking anywhere in A.P.,F.O.R. destination including, loading, unloading & stacking at site but excluding central excise duty, sales tax, octroi and other Govt levies etc., as applicable.H.D.-10with 560mmdia clear opening(New item) I.S.I Mark

Supplying and fixing of NP coat hooks

Supply of ISI ……… outer dia medium grade with IS:9537 part 3 FRLS regid PVC conduit Makes : Precision/Universal & Marudhar/VIP / GoldMedal /Million plast / GM / Sudhakar /Anchor/ Polyline/ Polycab/Orbit/ AKG -do- 50mm (2.85 mm thickness)

Supply of …………….. PVC Bends Make Precision/Universal& Marudhar/VIP / GoldMedal/ Million plast / GM / Sudhakar / Polyline/ Polycab/ AKG/Orbit -do- 50mm (2.0mm thickness)

Supplying and fixing TV shape mirror with plastic frame size 609.6 mm x 457 .2 mm

Flooring with Antiskid floor tiles 1st quality of all series& shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work.

Supply of Non-skid red or white full body Ceramic floor tiles of size 450 x 450 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Finishing the sides of walls with Ist quality glazed wall tiles of following sizes of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg/10sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls).

Supply of glazed red or white full body ceramic wall tiles of size 300x600 mm and thickness between 6-8 mm ist quality confirming to :IS 13712,IS13630 ( parts 1 to 15)of any colour and finish in all shedes and designs,

Electrical items

Supply and Fixing of ISI mark 25mm outer dia heavy grade (2.20mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in new / existing brick building, walls, columns, beams duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and masonry work for light, fan and separate plug point including all labour charges etc., complete. Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal

Supply and wiring with 3 run of 14/0.3mm (1.0 sq.mm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping with 3 plate Jumbo ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings. Grade-A: Wire Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI Grade-A: Modular Switch Makes: Legrand Arteor / Schneider Zen cello / Gold Medal / GIFA / L&T englaze / Crabtree - Murano / Amare / Ducor / GM Four-Five

Supply and wiring with 3 run of 14 / 0.3mm (1.0Sqmm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping without ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI Grade-A: Modular Switch Makes: LegrandArteor / Schneider Zen cello / Goldmendal / GIFA / L&T englaze / Crabtree- Murano / Amare / Ducor / GM Four-Five

Supply and run of 3 wire of 36/0.3mm (2.5 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and run of 3 wire of 56/0.3mm (4.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI (Rate as per item No.2.3.23 of Elec SSR 2020-21)

Supply and fixing of fan hook made out of 3/8" (10mm) M.S.Plain rod and providing to the existing M.S. Rod at the time of concreting the roof slab.

Fixing of Ceiling fan including transportation and giving connections with twin core wire etc., complete.

Fixing of given (9" to 24") Exhaust fan of in wall with necessary connections and masonry work of making hole, finishing etc., complete

Supply and fixing 10W LED Bulk head fitting with Pressure die cast alluminum with opal diffuser with IP 65 Protection etc., complete. Makes: Philips / Bajaj / Crompton / Surya / Havells / Greenlites /Insta Power/ HPL / Halonix

Supply and fixing of 3 Modular Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 6 Modular Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 12 Modular Vertical Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 3 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen / Fortune Art.

Supply and fixing of 6 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian /Siemen /Fortune Art.

Supply and fixing of 12 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB /Indo Asian / Siemen / Fortune Art

Supply and fixing of 6 /10 Amps 1 way 1 module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 6 /10 Amps 3 / 2 pin 2 module Modular Socket with shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 16 /20 Amps 1 Way 1 Module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 20 Amps 2 Module Modular Socket with Shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 100 W Fan Step Regulator of 2 Module on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 18W LED Slim Panel Round /Square suitable for Recessed / Surface mounting made of diecast aluminum body with powder coating, acrylic diffuser with driver as per IS: 15885 (Part 2/ Sec 13) : 2012, operating voltage range of 150 to 265 Volts AC, P.F > 0.9, Surge protection: 2KV, THD<10%, with high power LEDs, having System Efficacy of >=100 lumens /watt, CCT: 3000K - 5700K, minimum CRI>70, Luminaire performance complies to IS 10322 (Part 5 / Sec-2) .etc., complete with earth connection and not less than two years warranty. a) LUMINAIRE MAKE : Phillips / GE- Venture / Crompton / Wipro / Bajaj / Havells / Halonix /Jaquar /HPL/GM / GreenLites / Gold Medal/ Eveready/ FortuneArrt/ Rhino/ Panasonic/ Ecolink/ Bee-lite/Capart-b b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG/ Everlight.

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=100 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty. a) LUMINAIRE MAKE : Phillips / GE- Venture / Crompton / Wipro / Bajaj / Havells / Halonix / Jaquar /HPL/GM / GreenLites / Gold Medal/ Eveready/Rhino/ Panasonic/ Ecolink/ Capart. b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG/ Everlight.

Supply of 48" (1200mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, input voltage 230V AC converted to 24V DC, power input not more than 30W, air delivery not less than 220 cubic meter/min and a minimum service value of 7.0, without Remote and without regulator. Makes: Atomberg/ Halonix/Havells/ Crompton

Supply of 12" (300mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with mark. Makes: Crompton / Almounard / Havells Ventil Air-DB

Supply and fixing of 4 Way TP & N Horizontal type Distribution board as per IS 8623; IS 13032; IEC 61439-3 with IP-43 protection (Metal door) firmly concealed in the wall with neat plastering etc., complete. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of 40 to 63 Amp TP MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 6 to 32 Amps DP MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 6 to 32 Amps range S.P MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of sheet steel enclosure with IP 20 Protection as per IS 8623; IS 13032; IEC 61439-3 suitable for DP/TP/FP MCBs firmly Concealed in the wall with neat plastering etc., complete. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of RCCB Up to 40A Double Pole, 30mA for earth leakage protection, confirms to IEC:61008 and IS:12640-1 in the existing boards including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and transportation of 95 Sq.mm 3 1/2 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-A: Make: Torent / Universal / Unistar / Havells / KEI / Gloster / Polycab / RR Kabel / Finolex.

Supply and transportation of 25 Sq.mm 3 1/2 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-A: Make: Torent / Universal / Unistar / Havells / KEI / Gloster / Polycab / RR Kabel / Finolex.

Laying of U.G cables size from 70 Sq.mm to 150 sq.mm and back filling of trench including labour charges etc., complete.

Only Laying of U.G cables upto 50 Sq.mm on wall including labour charges etc., complete.

Only Laying of U.G cables size from 70 Sq.mm to 150 sq.mm on wall including labour charges etc., complete.

Earth Work excavation for trench for laying of U.G. Cable in ordinary Soils, manual means to the required width and depth and depositing the same on bank as directed during execution etc., complete .

Supply and making end termination with heavy Alluminium lugs (pin / ring type) for 25 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and making end termination with heavy Alluminium lugs (pin / ring type) for 50 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and making end termination with heavy Alluminium lugs (pin / ring type) for 95 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and fixing of fabricated M.S clamps made out of 25mm x 3mm MS flat with necessary holes on either side with suitable 1 1/2" coach screws and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of UG Cables of size 25 Sq.mm to 50 Sq.mm on walls etc., including all labour charges etc., complete.

Supply and fixing of fabricated M.S clamps made out of 25mm x 6mm MS flat with necessary holes on either side with suitable 1 1/2" coach screws and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of UG Cables of size 70 Sq.mm to 120 Sq.mm on walls etc., including all labour charges etc., complete.

Supply Laying and Transportation of Outer dia 90mm and inner dia 76mm, 6Kg/Sq.Cm (PE- 100 grade) double walled corrugated HDPE duct made as per specification BSEN - 500 86/IS 14930 Part-II. Make: DURA LINE (Dura Guard) or its equivalent make.

Providing earthing as per IS 3043/ 1987 with 100mm (ID), 13mm thick C.I. Pipe of 3.0 mtr. length after excavating an earth pit of size1.5 m X 0.9 M X 3.00M(Top 1.50 m X 1.20 m X 0.9m & bottom 1.20 M X 1.20 M X 1.65 M) and filling with a homogenous layer of 40 Kgs. of Coke / Char Coal, 20 Kgs. of Salt and the required quantity of sand around 100mm pipe from the bottom of the pipe to a height of 2.7mtr. and filling the remaining excavated portion with earth and consolidation / Settlement of the trench should be done by filling with sufficient quantity of water.

A concrete bed of size 0.8 M X 0.8 M X 0.1 M thick and an inspection chamber having inside measurements of 0.4 M X0.4 M X 0.4 M with wall thickness of 100 mm with cement concrete CC (1:2.5:5) using 20 mm HBG Metal is to be constructed with side wall 100 mm above ground level and plastering the exposed walls neatly with CM (1:3) with 12 mm thick. The Top of the Inspection Chamber is to be provided with reinforced precasted RCC Slab with 40mm thick with lifting hook.

The top of C.I. Pipe is to be fixed & welded with suitable G.I. Wire mesh funnel 50mm x 6mm G.I. Strip having length of 300mm is to be fixed to the top of C.I. Pipe with G.I. Clamps fabricated with 50 x 3mm G.I. Flats with necessary bolts and nuts and necessary welding to be done to the clamps and C.I. Pipe. 2 Nos. of holes are to be drilled on either side of G.I. Flat for Extending earth connections. 65mm dia PVC Pipe is to be embedded at the pit entry for earth. After laying earth from earth conductor bus to Electrode trough PVC Pipe, the surface should be covered with bitumen and grease. The cost of GI/Copper flat to be run from CI Pipe electrode to the equipment is to be made separately on running meter basis. The work shall be executed strictly as per IS 3043 - 1987.

The rate includes cost and conveyance of all materials, labour charges, incidental charges etc., complete (Note:- Necessary meggaring testing is to be carried out in the presence of concerned Engineers and measurement of resistance shall be as per ISI standards)

Supply and run of ' 8 ' SWG G.I wire for earth electrode to required places by Surface in walls, flooring including cost of all accessories and giving necessary connection with 3/8"x2" GI Bolts, Nuts and Washers wherever joints has to be done. The strip has to be either rivited (or) bolted (or) gas welding neatly and all labour charges etc., complete.

Supply & fixing of 1" dia 'B' class GI pipe not exceeding 1.5Mtr long with necessary bending (120° to 135°) to the wall or to the pole as directed during execution duly grouting 2 Nos. of MS angle of 35x35x5mm having length 20Cm (grouted portion of MS angles into the wall 7.5cm) and fixing with 2 Nos. of MS clamps fabricated with 25mmx3mm MS flat with suitable holes and 4 Nos. of 3/8"x2" MS bolts, nuts & washers for fixing on the wall / 2 Nos. of suitable MS clamps with bolts, nuts for fixing to the pole etc., complete. A 16Amp fuse unit is to be fixed to the MS angle / clamp and giving necessary connections with 14/0.3mm PVC copper flexible wire from pole to the fuse unit and to the fitting or from Ceiling rose in the building to the fuse unit and to the fitting with link clips etc., and the GI pipe has to be painted with two coats of enamel grey paint over one coat of red oxide paint. Fixing charges for stem pipe including the cost of MS angle, MS clamps, bending of pipe, bolts,nuts, fuse units etc

Fixing of M.V / S.V / M.H luminaire /LED / Halogen fitting on wall / pole cross arm / channel / stem pipe etc., including all labour charges and giving connections etc., complete.

Supply and transportation of 60W LED Street light Luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass/ temperature protective polycarbonate diffuser, supply input voltage 120 - 270V AC, P.F > 0.90, high power LEDs having System Efficacy >=120 lumens/watt and junction temperature < 70°C, with Ingress protection IP66, Luminaire performance complies to IS 10322 (Part 5/Sec- 3), driver surge protection 4KV, in-house additional Surge protection 10 KV with optics distribution, THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty.

a) LUMINAIRE MAKE : Wipro(Skyline) / Philips (Green line) / GE-Venture / Crompton(Neo Series) / Bajaj (Edge) / Halonix (Lumos - Super) / Havells (Endura Series)/ Valmont(Supernova) / Capart (Premium) / Greenlites(Hi-Lux) /Polycab /Keselec/ HPL(City Vision)/Jaquar (Premium) /Eveready/ Surya (Lexon) / FortuneArrt (Leaf) / Rhino (GPSL04)/ Orient(Fiest Plus) /Bee-lite(Gritty)/ Ecolink(Durastreet Gen II) b) LED MAKE : PHILIPS LUMILEDS /CREE/ NICHIA / OSRAM / SAMSUNG / LG

Supply of 4 Way VTPN MCCB DB with IP 43 Protection suitable for accommodating 125A / 160A 4 Pole MCCB as incomer and TP/SP MCBs as outgoings etc., as per IS 8623; IS 13032; IEC 61439-3. Makes: Legrand(Ekinox 3) / Schneider-A9/Hager - Novello+/ Seimens/Havells STADx/ Lauritz Knudsen (formerly L&T) -Newrange/Indo Asian-Opti Pro/ HPL (Techno)/ Anchor (Uno Plus)/ABB-ITUS

Supply and fixing of 125A 4 Pole MCCB, Adjustable, Confirms to IEC 60947-2 and IS 13947-Part 1&2 having Breaking Capacity 25 KA, with thermal magnetic release in the existing board including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and run of 5 wire of 126/0.4mm (16 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply installation Testing and commissioning of 10.0 KVA 312/360 V DC KVA on line UPS system as per IEC 62040-I (Safety), IEC 62040-3 (Performance) for critical IT solutions, fully digital IGBT Converter and Inverter, SCR rectifier with Internal /External isolation transformer from DC to AC, PWM, pure sine wave output, double conversion, output pf 0.8, with paralleling facility, standard communication features/options auto and manual static by pass switch three phase input / Three phase output. acoustic level shall be less than 58dB at 1 mtr distance. Makes: Numeric/APC/Fuji Electric / Sakshham / Emerson/Techser

Supply and fixing of 12V 42 AH SMF battery with 3 years warranty including wire leads, connections etc, complete. Makes: Quanta / Racket / Exide.

Rupees One Crore Sixty One Lakh(s) Thirty Six Thousand Nine Hundred Twenty Two And Paise Ninety Four Only