Construction of SE Residence for newly created circle office Dehra in Tehsil Dehra Distt. Kangra

Excavation in foundation and trenches etc.(in pipes and pits) in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiselling/wedging out of rock/where blasting prohibited) saturated soil stacking the excavated soil as directed by the Engineer-in-charge clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth

in Soft Rock 40 % Chieselling work 60%

Providing and laying cement concrete 1:3:6 (1Cement:3sand:6 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work foundation and plinth complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain.

Foundation Footing Bases of Coloumn,Pillar etc complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Sides & soffits of beams cantilevers, girders & lintels, , haunching, cantilevers,bressumers 1.00 mts. In depth in all heights from floor complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors upto 200mm kin thickness. complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Coloum Pillar Posts struts etc complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Vertical surfaces such as wall (any thick.) partitions & the like i/c attached pillasters, buttresses,plinth & string courses & the like complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and laying cement concrete work 1:1.5:3(1cement:1.5sand: 3 graded stone aggregate 20mm nominal size ) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

Foundation,footing,bases of columns & the like & mass concrete etc complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Suspended floors, roofs, landings and shelves and their supports, balconies, beams ,griders bressumers and cantilevers upto all floor level complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Columns,pillars,posts & struts upto floor two level complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Lintels, beams ,griders bressumers and cantilevers upto all floor level complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing Tor steel reinforcement for RCC work including bending,binding & placing in position complete upto floor two level complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Ist class brick work using Common burnt clay building brick with fine surface and even edges in common burnt clay building bricks,laid with 12x12mm deep cut pointing, in supper structure above plinth upto floor two level in cement mortar 1:6(1cement:6sand) including carriage of materials complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing wood work of in frames of doors,windows,clerestory,windows and other frames wrought, framed and fixed in position complete including carriage of materials in all leads & lifts. (Ist class indian teak wood ,minimum weight 700 to 800 kg/cum) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors,windows and clerestory windows i/c bright finished/black enamelled iron butt hings with necessary screws 1st class teak wood 40mm thick including carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws 1st class teak wood 40mm thick including carriage of material in all leads & lifts.ist class teak wood complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

20mm cement plaster in single coat of rough sides of bricks/concrete stone walls for interior plastering upto floor two level including arrises internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement:6sand) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

15 mm thick cement plaster in single coat on rough side of brick/ stone/ concrete walls for interior plastering up to floor -2 level including arrisses,internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement,6 sand ) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

6 mm cement plaster to ceiling in CM 1:4 (1Cement :4 Sand) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone aggregate 20mm nominal size) including finishing of the top surface of concrete smooth complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing under layers for plinth protection of 75 mm thick ( unconsolidated) bed dry brick/stone aggregated 40 mm nominal size will rammed 7 consolidated & grouted with fine sand including preparation of gruond complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Polishing two coats with PU(poly utherene) polish with complete process including three coats of sealer as required of required shade on new wood and wood based surfaces to give an even and soft semi gloss top coat surface, including cleaning the surface of all dirt, dust and sand papered smooth and including coats of wood filler complete in all respect including carriage of material in all leads & lifts (161060000).(Sirca/Asian/Jindal make.) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Applying spirit or oil stains any colour on wood and wood based surfaces(sirca-light wall nut shade) to give an even surface including cleaning the surface of all dirt/dust required for PU. Poliosh finish,sand papering stopping and knotting complete.(item no. 16049000).(Sirca/Asian/Jindal make.) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Applying Birla white wall care putty minimum three coats over plastered surfaces after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final smooth finish to the surface complete ready for final coat of wall emulsion in all respect including carriage of material in all leads & lifts (16103000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/ masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete complete in all respect including carriage of material in all leads & lifts (16101000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equavallent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in all respect including carriage of material in all leads & lifts (16104000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wall painting (two coats) with Royal emulsion asian /Dulex makepaint of approved brand and manufacture for interior grade on undecorated interior plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth, excluding coats of putty as required for making the surface even/smooth complete in all respect including carriage of material in all leads & lifts (16105000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing M.S.fan clamp(Type-I of 16mm dial M.S. Bar bent to shape with hooked ends in RCC. Slab during laying including painting the exposed portion of loop all as per standard design complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

In all Rooms on Ground & First Floor complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dial meters bolts and nuts and wooden plug and embeding in cement mortar block 30x10x15cm (1:3:6(1cement:3sand:6 graded stone aggregate 20mm nominal size complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing bright finished stainless steelsliding door-bolts with nuts and screws etc. complete in all respect including carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

300x16 mm (1211001000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing fixing bright finished stainless steel tower bolts (barrel type) with screws etc. complete. in all respect including carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

300x10mm (1211102000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

150x10mm (1211103000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

150 mm (1211301000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

125 mm (1211302000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Stone/Boulder filling under floors/behind retaining walls complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and laying cement concrete work 1:2:4 (1Cement : 2 Sand : 4 Graded stone aggregate 20 mm nominal size ) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:- Foundation & Plinth complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 9mm thick polished/satin/matt/ antiskid water proof stain and impect resistent heavy duty vetrified tiles degital/ full body of Simpolo/KaJARIA/ Nitco or equivalant 60X60cm OR60x120cm OR 80X120 ,20x120cms manufactured of approved shade and colour inflooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts. (13680000)(fixed with 5mm spacer,filled with epoxy or flush joints) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and laying granite stone 16 to 18 mm thickness, lapato finish (south mines) in steps,flooring with 20mm(average)thickness base of cement mortar 3 (1cement:3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 19mm thick water proof HDHMR board 19mm thk, Action tessa make both side laminated in shelves/box for cup board with butt joints & fixing with nails & screws etc complete in all respect including carriage of material in all leads & lifts.(1218000000).(centuary/virgo/green make) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 8mm thick HDHMR board standard quality and of approved shade & design for back side of cup boards,wall panelling etc fixing with approved adhesive, butt jointing and nails & screws complete (Base frame work to be measured & paid for separately) complete in all respect including carriage of material in all leads & lifts.(1218400000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing square edges cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete in all respect including carriage of material in all leads & lifts. 1st class deodar wood (1218302000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing bright finished hard drawn hooks and eyes complete in all respect including carriage of material in all leads & lifts. (1212204000) 150 mm complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

P/F bright finished brass Godrej /Hettich make mortie lock with all acessories 150 mm size complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

P/F Heavy duty hydraulic door closer Godrej make/Hettich make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing bright finished brass handles for cup board with screws etc. complete. in all respect including carriage of material in all leads & lifts. 150 mm complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

P/Fixing door shutter stopper for wire gauge shutters 100 mm long (stainless steel) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

P/Fixing rubber block for back door stopper 100 mm size and 50 mm dia complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting,fixing in position and applying a priming coat of red lead paint. In MS hollow square/rectangluer pipes (tata /apollo make)beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like complete in all respect including carriage of material in all leads and lifts. (1504010000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 0.63mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing withself drilling screws, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees including carriage of material in all leads and lifts as required as per the direction of Engineer-in-charge (14550000).( Tata durasine make, smart colour complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing ridges or hips 60cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories including carriage of material in all leads and lifts as required as per the direction of Engineer in Charges (14560000).Tata durashine make.) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete under flooring complete in all respect including carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand :10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads & lifts (19060000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing plaster of paris(POP.) false ceiling 12 mm thickplaster, fixed over GI Mesh 5x5mm size, weight min. 0.70kg/sqmt ,GI sections (Min.0.350kg/mtrand wire mesh,:L-connectors, rawl plugs, complete as per Arhitectural drawings complete) all material chetak.Jindal Make),cross and main section ,grid size 45x90cms maximum.complete as per directions of Architect/Engg-in-charge)(Sakarni or Birla make Plaster of paris brand to be used) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing stainless steel railing for stairs/balconies using 304 grade,Jindel coil, top hand rail 50 mm diameter@ 1.85kg/mtr,40x40mm square balusters @ 1.5kg/mtr,fixed at alternate step or 60 cms intervals , 4 nos 20x20mm horizontal sq.pipes(1.20kg/mtr) welded to balusters, balusters fixed to steps by drilling in tread and fixing of 16mm, bolt 50 mm long and washers complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 12 mm thick toughned glass railing for front two balconies, glass height=75cms fixed with heavy 3.00 kgs each base stainless steel 304 grade studs fixed at 60 cms intervals,top hand rail 65x65 mm @ 2.5kg/meter, complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and Laying cement concrete 1:5:10(One cement:Five sand:Ten approved graded stone aggregate 40mm(Forty milimetres nominal size)with 15% plum and curing compolete excluding the cost of form work in retaining wall/breast wall. The size of plum shall usually 150mm to 300mm as per HPPWD specification complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and laying heavy duty precast cement conrete inter locking paver blocks, 60 mm thick. vibro compacted upto M-50 grade ( NTC make) i/c border or kurb blockof required shade fixed over sub-base of concrete,with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks complete in all respect including carriage of material in all leads & lifts (13710000) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group-C complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

4 modules(140mmx78mmx50mm) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

6 modules(205mmx78mmx50mm) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

8 modules (120mmx135mmx60mm) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

12 modules (205mmx135mmx60mm) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm. complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

2x2.5 Sq. mm. complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

2x4.0 Sq. mm. complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing wire from MCB box to main pannel board complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulatedheat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing three phase wiring in main pannel board for busbar complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

S.P. 5/ 6 Amps one way Modular switch complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

5 pin, 5/ 6 Amps Modular socket outlet complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Bell push, Modular complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

S.P. 15/ 16 Amps one way Modular switch complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

6 pin,15/16 Amps Modular socket outlet complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing TV. Socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing Telephone socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing ceiling rose on the existing junction box /wooden block including connections etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing of Double door-12 way single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnec- tions, phosphatized and powder painted, including earthing etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing 63 Amps. Cat-A rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450mm & cross-sectional area(25.4mmx4.75mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530mmx450mmx 150mm) nominal with all accessories including connections, earthing the body etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required. 100 Amp. Category-A complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Single pole & neutral. Cat-B in the existing MCB DB complete with connections etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35 mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Double pole. Cat-B in the existing MCB DB complete with connections etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing 40 Amps. Cat-B rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing TP&N switch disconnector fuse unit panel mounting, 415/500 volts with 3 No. HBC/HRC fuses, open execution, including drilling holes in the cubical, making connections, etc. as required. 200 Amp. Category-A complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing of lightning conductor finial, made of 25 mm dia. 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for vertical run) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for horizontal run) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, rmoured/ XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the Armoured cable 4 sq. mm (twin core) for Yard lights complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and installation of sanitory storage type Electric water heater (Geyser) of 30ltrs capacity by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection making good the damages, electrical connections, safety valve connections, testing and commissioning etc. 30Liter capacity water heater (Cat-A) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing, Installation, testing and commissioning of decoratice , ceiling fan without regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. Ceiling Fan 1400 mm sweep, Category-A complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and installation of Exhaust Fan, Light duty, (Domestic) 225 mm sweep in the existing opening, including taking the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 2 x36 watt-LED Panel surface mounting /recessed type light fixture 60x60cms size syska/jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing of fancy wall bracket containing thread type LED lamp holder (s) of all sizes and shapes, complete with all accessories but excluding LED lamp including making connections, testing etc. as required. Fixed type wall bracket 150 dia, single lamp.(Category-A) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing, Installation, testing and commissioning of prewired flourecent tube fitting 1x20W LED complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing Buzzer / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing Surface LED light fixture, 6 to 28 watts suitable for D.C./A.C. single phase,230 volts fixing complete on ceiling /walls complete as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

P/F. 6 to 12 watt downlighter/cove light tiltable in false ceiling, focus type Havells make including holes in false ceiling complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing of integral LED Post Top Lantern of following capacity, cast aluminium spigot, spun aluminium canopy, opal acrylic diffuser, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required. Gate post top lantern - CLED 22 watt complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing boundary lights 20x30cms clear light fixture, top mounted,with 20 watt LED bulb complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

WATER SUPPLY AND SANITARY

Providing and fixing high pressure spigot and socket waste ventilating pipe of following daimeter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

75mm dia

110mm dia

Providing and fixing PVC plain bend of following diameter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

75mm dia

110mm dia

Providing and fixing PVC door bend of following diameter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

75mm dia

110mm dia

Providing and fixing PVC collar/ socket of following diameter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

75mm dia

110mm dia

Providing and fixing PVC Single equal brach of following diameter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach with oval access of following diameter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

75mm dia

100mm dia

Providing and fixing PVC Floor traps 110x75mm i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing viterous China wash down water closet (European Type WC pan) with intergral S” trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement: 1 sand) including entire carriage of material within all leads and lifts.(jAQUAR/CERA MAKE) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Wall mounted EWC with full frame, built in concealed cystern,seat cover,cistern push button complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing vanity type wash basin 80x50x70cms, somany make,stainless steel body complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing of MI union for wash basin 32mm dia i/c carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 32mm dia PVC waste pipes for wash basin i/c brass check nut i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 90x60cms. bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass towel rail complete with C.P.brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts 600 x 20mm. Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 600x120mm glass shelf i/c entire carriage of material within all leads and lifts.Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP toilet paper holder i/c entire carriage of material within all leads and lifts.Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP brass soap dish i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing Tooth brush and tumbler holder i/c entire carriage of material within all leads and lifts.Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP brass shower 250mm dia,with 60 cms long rod, i/c entire carriage of material within all leads and lifts.Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing brass CP wall mixture for hot/cold watmixing for bathing area complete Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP tap short/ long body, Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing brass angle valve 15 mm dia without nut and pipe i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP concealed stop cock 15 mm dia without nut and pipe i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing single hole single lever wash basin mixture i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing PVC connection 15mm dia i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing 100mm dia, C.P. brass grating including carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing Jet connection ,health facut ,fixed for WC seat i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP towel ring i/c entire carriage of material within all leads and lifts.Jaquar make complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing CP towel rack 600x250mm for VIP toilet i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing and fixing wall to ceiling and floor galvanised mild steel tubes light grade), tube fittings and clamps i/c making good wall ceiling & floor of following diameter i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

15mm dia

20mm dia(ALL INTERNAL FITTING OF TOILETS)

32mm dia

Providing & fixing Brass full way wheel valve i/c entire carriage of material complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

15mm dia

20mm dia

32mm dia

Providing and fixing 2000 ltrs. Tripple layer sintex make water storage reservoir with top lid and making connection complete in all respect including all leads and lifts complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Constructing manhole with RCC top slab in 1:2:4 mix ( 1 cement :2 sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 ( 1cement:4sand :8graded stone aggregate 20 mm nominal size),inside plastering 15 mm thick with cement mortor 1:3 (1cement:3sand),finished with a floating coat of neat cement & making channels in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20mm nominal size) finished smooth complete i/c curing &testing. (i) inside size 1200 x 900 x 1000 mm deep i/c c.i. cover with frame (m. duty) with single pattern 455 x 610 mm internal dimensions (total wt.of cover & frame to be not less than 38 kg) 23 cms. thick brick masonry walls using 2nd class brick in cm 1:3 (icement : 3 sand) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Providing & fixing stone ware gully trap grade 'A' complete with CI grating,B/Masonry chamber in cement mortor 1:5 & water tight CI cover with frame of 300 mm x 300 mm size (inside) .The wt.of cover to be not less than 4.53 Kg & frame to be not less 2.72 Kg. (Square mouth traps 100 x 100 mm size) complete in all respect within all leads and lifts as per direction & satisfaction of Engineer-in-Charge.

Please Enable Macros to View BoQ information