Construction of Pong View residential Colony at Dehra Distt. Kangra HP

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m. as directed by the Engineer-in- charge. (a) All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for including carriage of material in all leads and lifts.

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying in position cement concrete of specified grade 1:5:10 (1 Cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering - All work up to plinth leve including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering - All work up to plinth leve including carriage of material in all leads and lifts.

Providing and laying in position cement concrete 1:1½:3 (1 Cement: 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) of specified grade excluding the cost of centering and shuttering all work up to plinth level including carriage of material in all leads and lifts.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts.

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering,finishing and reinforcement including carriage of material in all leads and lifts.

Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) of specified grade excluding the cost of centering and shuttering - All work up to plinth levelincluding carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level including carriage of material in all leads and lifts. (a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor-V level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in below plinth level up to floor-V level in all shapes and sizes in cement mortar 1:4 (1 cement :4 coarse sand) including carriage of material in all leads and lifts.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure below plinth level up to floor-V level in all shapes and sizes in cement mortar 1:4 (1 cement : 4 coarse sand) including carriage of material in all leads and lifts.

Providing and fixing colour coated aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) including carriage of material in all leads and lifts.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge . (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness weight not less than 10.00 kg / sqm including carriage of material in all leads and lifts.

Providing and fixing 10mm thick bakelite sheet melamine resin, phenolicresin and kraft paper conferming to IS 61642379 Grade-I in panelling fixed in aluminium door window shutter and partition frames with CP brass / stainless steel screw etc. complete as per architectural drawing and direction of Engineer-in- charge including carriage of material in all leads and lifts.

Providing and fixing anodised aluminium grill colour coated (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. (Only weight of grill to be measured for payment) including carriage of material in all leads and lifts.

Providing and fixing colour coated aluminium sliding door bolts, ISI marked anodised (anodic coating not less than Grade-AC 10 as per IS:1868), transparrent or dyed to required colour or shade with necessary screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing colour coated aluminium tower bolts, ISI marked anodised (anodic coating not less than Grade-AC 10 as per IS:1868), transparrent or dyed to required colour or shade with necessary screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing colour coated aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing bright finished brass hard drawn hooks and eyes including carriage of material in all leads and lifts. (a)150mm dia.

Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing colour coated aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including carriage of material in all leads and lifts.(a) Twin rubber stopper

Providing and laying glazed vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of material in all leads and lifts. Size of Tile 600x600 mm

Providing and laying glazed vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of material in all leads and lifts. Size of Tile 600x600 mm

Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete including carriage of material in all leads and lifts.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete including carriage of material in all leads and lifts.

Providing and laying polished Gramite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the aechitectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curring and polishing etc.all complete as specified and as directed by the Engineer-in-charge Polished Granite stone slab jet Black,Cherry Red,Elite Brown,Cat Eye or equivalent. including carriage of material in all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.including carriage of material in all leads and lifts.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws complete including carriage of material in all leads and lifts.(i) Ridges plain (500 - 600mm)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws complete including carriage of material in all leads and lifts.(i)Flashings/ Aprons.( Upto 600 mm)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws complete including carriage of material in all leads and lifts.(i)Gutter (600 mm over all girth)

Providing and fixing precoated linner sheet in ceiling 0.50 mm thick including cutting fixing to steel member including base member of steel work and applying a coat of red lerad primer complete as per the instrction of incharge (base memebers of steel work shall be measured and paid for separately) including carriage of material in all leads & lifts.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion ,(i) single socketed pipes 110 mm diameter including carriage of material in all leads and lifts.

Providing and fixing on wall face unplasticised - PVC moulded fitting/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS: 5382,leaving 10 mm gap for thermal expansion. including carriage of material in all leads and lifts.

Plain bend 110mm

Plain shoe 110 mm

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382,Leaving 10 mm gap for thermal expansion. including carriage of material in all leads and lifts.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. including carriage of material in all leads and lifts. (a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Finishing walls with 100% Premium emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm including carriage of material in all leads and lifts.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. including carriage of material in all leads and lifts.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)including carriage of material in all leads and lifts.

6 mm thick on ceiling with cement mortar 1:3 (1 Cement : 3 fine sand) including carriage of material in all leads and lifts.

15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts.

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand) including carriage of material in all leads and lifts.

20 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material in all leads and lifts.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. including carriage of material in all leads and lifts.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand) including carriage of material in all leads and lifts.

Constructing cousre rubble hammer dressed "U" shape open surface drain with side wall 15x22 cm n cement mortar 1:6 (1 cement :6 sand) and in side plastering with cement mortar 1:3 (1 cement :3 sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 cement :5 sand:10 graded stone aggregate 40 mm.nominal size) and 7.5 cm cement concrete 1:2:4 (1 cement :2 sand :4 graded stone aggregate 20 mm .nominal size) and finished with a floating coat of neat cement complete as per standard design.including carriage of material in all leads and lifts.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: IVth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm) including carriage of material in all leads and lifts.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including carriage of material in all leads and lifts.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC olvent cement and testing of joints complete as per direction of Engineer in Charge. including carriage of material in all leads and lifts.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : including carriage of material in all leads and lifts.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer. including carriage of material in all leads and lifts.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250. including carriage of material in all leads and lifts.

610x460 mm bowl depth 200

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore. including carriage of material in all leads and lifts.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. including carriage of material in all leads and lifts.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. including carriage of material in all leads and lifts.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. including carriage of material in all leads and lifts.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (i)15mm nominal bore. including carriage of material in all leads and lifts.

Providing 15mm Mixer for kitchen sink with casted swinging spout at top including carriage of material in all leads & lifts.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. including carriage of material in all leads and lifts.

Providing and fixing PTMT grating of approved quality and colour.100 mm nominal dia including carriage of material in all leads and lifts.

Providing and fixing toilet paper holder :C.P. brass including carriage of material in all leads and lifts.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. including carriage of material in all leads and lifts.

Providing and fixing ISI marked high pressure PVC (Finolex) spigot and socket, waste and ventilating pipes including all accessories including fixing with approved adhesive etc. complete fitting including carriage of material in all leads and lifts.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. (a) Inside size 800mm x 800mm and 500mm deep including S.F.R.C. frame and cover medium duty 500mm diametre internal size.With 200mm thick walls of brick masnoey using common burnt clay building bricks in cement mortor 1:3 (1 cement :3sand) including carriage of materials in all leads and lifts.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. including carriage of material in all leads and lifts.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including carriage of material in all leads and lifts.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern including carriage of material in all leads and lifts.

Providing & fixing division plate for urinal 600mm x 300mm Vitrious china. including carriage of material in all leads and lifts.

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the walls and floors including carriage of materialn all leads and lifts.(i)110x90mm

MUNISH KUMAR

M/s Sunny Mandla

sourav mahajan

A K CONSTRUCTION

Vipul Bali Govt. Contractor

ABC Construction

M/s Shivom Engineering and Services/Prop. Abhilash Sharma