Construction of 02 Nos Pump Houses of existing DTW or IRP. Construction of Filling Stations including C.C. interlocking paver block pavement at Manubazar Sector of Satchand R.D. Block within the Sabroom Sub-Division during 2025-26.(2nd Call)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) All Kinds of Soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. A)All kinds of soil

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

i) 1:2:4 ( 1 Cement: 2 fine sand : 4 well burnt brick aggregate 40 mm nominal size)

ii) 1 : 3 : 6 ( 1 cement : 3 fine sand : 6 graded well burnt brick aggregate of 40 mm nominal size)

Centering shuttering including struttings, proppingetc. and removal of form work for: i) Foundations, footings, bases for columns

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level: i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size

i) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank

ii) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank

iii) Weather shade, Chajjas, corbels etc., including edges.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. i) Thermo-Mechanically Treated bars of grade Fe-500D or more

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above Plinth level i) Thermo-Mechanically Treated bars of gradeFe-500D or more

First class brick work in foundation and plinth including cost of all materials as required complete: i) In cement mortar 1:4 ( 1 cement : 4 fine sand )

First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- i) In Cement mortar 1:4 ( 1 cement : 4 fine sand )

Extra for brick masonry work in triangular, square and rectangular pillars including cost of all materials as required complete.

Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- i) In Cement mortar 1:4 ( 1 cement : 4 fine sand )

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- i) In Cement mortar 1:4 ( 1 cement : 4 fine sand )

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. I ) Fixed to steel windows by welding.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:- i) Using flats 30x6mm for diagonal braces and central cross piece.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. i) Hot finished welded type tubes

Providing and fixing M.S. round holding down bolts withnuts and wahser plates complete as per standard design.

Cement concrete flooring 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. all completeetc as per direction of Engineer-in-charge. i) 40 mm thick with 20 mm nominal size stone aggregate

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete as per direction of Engineer-in-charge. i) 0.63mm thick with zinc coating not less than 275gm/m2

12 mm cement plaster of mix. i) In cement mortar 1:4 (1 cement : 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix: In Cement mortar 1:4 ( 1 cement : 4 fine sand )

6 mm cement plaster of mix : Cement mortar 1:4 (1 cement : 4 fine sand)

Neat cement punning.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : 12.35.1 New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : New work ( two or more coats applied @ 3.84 kg/10 sqm)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content [Payment shall be made after submission of Test Certificate issued by the Manufacturer]. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and placing of G.I. pipe over the pump house on top portion of the R.C.C. column as per specification and the direction of the Engineer-in-charge. i) 150 mm dia

80 mm thick factory made c.c. interlocking paver block of M-35 Grade Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern.

Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked, BEE 1 star/minimum service value 4.0 m3/min/W) : -

Supplying of wooden toll box of size 1.00x0.60x 0.75 in/c us balts and painting complete and painting complete as per direction of the Engg-in-charge.

Supplying of plastic chair of approved make and quality in W/S scheme as per direction of the Engineer-in-charge

Supplying of plastic table of approved make and quality in W/S scheme as per direction of the Engineer-in-charge

i) Sly wrench

iii) Pipe Wrench

iii) plier (8")

iv) Screw driver

v) Hacksaw

Providing and fixing C.I. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge. i) 100 mm dia. A. PN - 1.6

Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. i. 100 mm dia.

Providing and fixing G.I. pipes medim class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling, cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. A. External work. i. 100 mm dia. nominal bore