Renovation and Supply of item at ward vikas kendra cum community building as urban health and wellness care poly clinic at ward no 19 under Gumla Nagar Parishad Gumla

Renovation and Supply of item at ward vikas kendra-cum-community building as urban health & wellness care poly clinic at ward no 06 under Gumla Nagar Parishad, Gumla

A. CIVIL Work

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material within 50 meters lead as directed by Engineer-in-charge

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty. 14.5.1 Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I

Providing and fixing glazing in aluminium door, window, ventilator.shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With float glass panes of 8 mm thickness (weight not less than 12.5 kg/sqm

patient room

nurse staff room

lab room

medicine /registration room

first floor room partition

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer on new surface including preparing plastered surface by rubbing smooth with pumice stone of fine paper applying putty wherever required scaffolding – do

external wall x direction

y direction

head room x direction

y direction

total (A)

less 1st floor open space x direction

y direction

total qty (B)

total qty (A-B)

Internal wall

bathroom corridor

bathroom

near entrance

stair

headroom

doctor room

1st floor 1 and 2 room

celling

total(b)

total qty(A+B)

less door

less window

total qty C

net qty(B-C)

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. Mode of measurement: Area shall be multiplied by the coefficient as indicated in building specification

main collapsible gate

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/I

Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fumed Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete

Covering of treated surface with PCC roof slab providing 50 mm thick cement concrete M20 (1:1.5:3) maintaining slope in alternate 2 mtr x 2 mtr panels with approved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing in position striking, curing, taxes and royalty all complete job

Providing and supplying Spandrel Glass Panels consisting of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface 2 of approved colour and shade so as to match the colour and shade of the IGUs in the curtain wall, all complete to the required performances as specified, as per the Architectural drawings and as approved shop drawings, as specified, and as directed by the Engineer-in-Charge

Providing steel truss made of M.S. pipe of 75 mm square (12.40 kg/m), pipe of 40 mm (3.50 kg/m), base plate 10 mm thick (78.50 kg/m²) and gusset plate 6 mm thick (47.10 kg/m²) — all complete job

stand post

principal rafter

purlin

add 5%extra

total

labour for fitting the truss

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer-coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/vertical/curved surfaces), excluding the cost of purlins, rafters, trusses and including cutting to size and shape wherever required (0.63 mm thick with zinc coating not less than 275 g/m²).

Providing ridges or hips of width 60 cm overall with plain G.S. sheet fixed with polymer-coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete (0.63 mm thick with zinc coating not less than 275 g/m²).

Providing and fixing vitreous china dual-purpose closet suitable for use as squatting pan or European water closet (Anglo Indian W.C. pan) with seat and lid, C.P. brass hinges and rubber buffers, 10 litres low-level flushing cistern with fitting and brackets, 40 mm flush bend, 15 mm nominal size C.P. brass angle valve, C.P. brass stop cock, 15 mm CP brass pipe, with all fittings of standard make and of approved design, complete including painting of fittings and brackets, cutting and making good walls and floors where required, all complete as per direction of E/I

Providing and fixing toilet paper holder: vitreous china combot

S/F/F THE FOLLOWING ITEM

Mirror 600x450 mm

C.P. brass towel rail

C.P. brass liquid soap containe

White vitreous china surgeon type wash basin of size 660×460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI mark

Providing and laying R.C.C. work in beams, suspended floors, having slope 15 degree landings, chhajjas, lintels, bands etc. (M 1:1.5:3) — all complete job

Providing steel reinforcement of bars (10 mm, 12 mm dia) as per approved design and drawing@120kg/m3 — all complete job

Providing fixing on wall face unplasticized rigid PVC rainwater pipe — do— 110 mm dia

Providing and placing on terrace( at all floor level )plastic water storage tank (ISI mark)

medical disposal pit

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1 Mtr. spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.

20mm nominal outer dia pipe

making soak pit 2.5 dia 3 mt deep with 45 *45 cm dry brick work honeycomb shaft with brick and sw drain pipe 100 mm dia pipe 1.8 m long comp. as per standard.

ALL SUPPLY ITEM RATE ARE TAKEN FROM GEM PORTAL

Hospital Bed

M P SURGICAL Patient Bed (Fowler) (Product ID: 5116877-15365991480

Chair – Executive Chair (for Doctor)(Product ID: 5116877-45125173589)

Table(Product ID: 5116877-53795773404)

3 Seater Chair(Product ID: 5116877-20027014749)

Office Chair(Product ID: 5116877-2686082320)

Folding Wheel Chair(Product ID:5116877-63780415508)

counter chair( product id :(5116877-54811780662)

fridge Voltas Laboratory Refrigerator >300<=350 Liters Capacity product id:(5116877-5521204984)

For Safety Purpose CCTV4MP (2560x1440) or better Bullet Camera(Product ID: 5116877-63274982166)

Monitor hp Flat LED Backlit LCD (Liquid Crystal Display) Computer Monitor hpR (ID: 5116877-85715663477)

Cable (ID: 5116877-27098169249)

installation and Commission Charge

CARRIAGE OF MATERIALS

sand( lead upto 20 km)

stone chips (lead upto 7 km)

Steel

Cement ( lead upto 1 km)

Electrical Work

Point rewiring in existing conduit: Rewiring for light/fan point /exaust fan point /call bell point 1.5 sq. mm FR PVC insulated copper conductor single core cable in existing surface/recessed steel/PVC conduit including dismantalling as required.

Group B

Twin control point re-wiring in existing conduit: Rewiring for twin control light point with 1.5 sq mm FR PVC insulated copper conductor single core cable in existing surface/recessed steel/PVC conduit including dismantalling as required.

Wiring for light /power plug with 2 x 4 sq mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

S/F light plug point with modular type accessories : supplying and fixing suitable GI Box with modular plac and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch connection painting etc as required (for light plug to be used in non residential buildings)

S/F Power plug point with modular type accessories supplying and fixing suitable GI Box with modular plac and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch connection painting etc as required (for light plug to be used in non residential buildings)

S/F 20 amps SPN MCB industrial socket outlet: Supplying and fixing 20 amps, 240volts, SPN industrial type , socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chaioned metal cover for the socket out let and complete with connections, testing and comissioning etc as required.

P/F M.V danger notice plate: Providing and fixing M.V. danger Notice plate of 200mm X 150mm, made of mild steel, atleast 2mm thick, and vitreous enameled white on both side, and with inscription in single red colour on front side as required.

Circuit and submain wiring in PVC conduit: Wiring for circuit/submain wiring along with earth wire with the following size of FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit as required.

2x1.5 sq.mm + 1 x 1.5 sq.mm earth wire. (For single separate 5 A)

2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire.(For switch board circuit)

2 x 4.0 sq.mm + 1 x 4.0 sq.mm earth wire. (to be used for sub main for common area like stair case and corridor)

2 x 6.0 sq.mm + 1 x 6.0 sq.mm earth wire.(to be used for sub main for each grt.)

Wiring in existing conduit: Supplying and drawing following size of FR PVC Insulated copper conductor single core cable in existing surface /recessed steel /PVC conduit including dismentaling as required.

1 x 1.5 sq.mm (Inverter wiring for light point)

S/F Modular type blanking plate: Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as required.

S/F S.P MCB DB: Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required. (but without MCB/RCCB/ISOLATOR)

12 Way, Double door

S/F 'C' Series, MCB: Supplying and fixing 6 amps to 32 amps ratings, 240 volts 10kA, "C" series miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commisioning etc as required.

6/32 amps, Single pole

40 amps, DP (To be used as incommer for all SP MCB DP-12Way)

S/F Ceiling rose: Supplying and fixing 2 pin 5 amp. Ceiling rose on the existing junction box/ wooden block including connection as required

S/F Batten/Angle holder: Supplying and fixing batten holder including connection as required.

S/F Electronic Musical call bell: supplying and fixing electronic musical call bell single phase, 230V complete as required.

ITC of Ceiling Fan: installation Testing and commisioning of ceiling fan , including wiring the down rods of standard length (up to 30 cm) with 1.5 sq mm FR PVC insulated , copper conductor , single core cable etc as required.

S/F Modular type electronic fan regulator : Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but excluding modular plate as required.

63 amp. Double pole change changeover switch in sheet enclosure with side handle operation (For DG and Mains line change over operation) ( Basic rate @3078 +14.95% CP+OH)

Electrical Appliance/Machineries

Silent Type DG Set of capacity 10 KVA Single Phase with AMF Panel IS/IEC-60034-1 IS: 1460 IS:13018 (Basic rate @395000 +14.95% CP+OH)

Ceiling fan 56" (1400 mm)BLDC 5 star IS:374:2020 (Basic rate @3400 +14.95% CP+OH)

12" (300 mm) metal exaust fan (Basic rate @1175 +14.95% CP+OH)

15/16 Watt LED Bulb

LED FLOOD Light 120W (For Entrance Outdoor ) ( Basic rate @8641 +14.95% CP+OH)

1.5Tr. 5 star split A.C (Inverter type) IS: 1391-part-1 (Category "A" (Daikin, Hitachi, L.G,Voltas or equi.)

3000VA sine wave inverter input AC range- 100V to 300V, wide- 90V to 300V AC, standard- 180V to 260V AC , DC Range- 10.5 to 14.2, Efficiency 80%, protection overload, short circuit. (Basic rate @27860 +14.95% CP+OH)

Add 18 % GST

Adding Labour Cess @ 1% of Estimated Cost

Please Enable Macros to View BoQ information