REPAIR/MAINT OF HARDSTADING, PATH,DRAIN,

Amount

Demolition of Cement Concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below or above ground level) complete all as specified and as directed

M&L PCC 1:3:6 type C2 ( using 40 mm grade aggregate) 75 mm thick as in plinth protection/sub base/ hard standing /paving complete all as specified and as directed

M&L PCC type B1 1:2:4 (20mm graded aggregate) 40mm thick as in floor finished surfaces even and smooth with using extra cement

Supply only Glass dividing strips 3 mm thick 38mm wide and placed in position complete all as specified

M&L PCC type B0 1:2:4 (12.5mm graded aggregate) 25mm thick as in floor finished surfaces fair and even to receive tile all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubish of the premises

M&L for Chequered cement concrete tiles 30cmx30cmx25mm thick, etc, jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm screed bed in CM 1:6 complete all as specified and as directed

M&L for Vibro compacted Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and pigment complete all as specified and as directed

M&L for Sand filling under floors or in foundation including watering and consolidation all as specified and as directed

M&L for endura tiles, heavy duty, for high traffic 300x300mm, 10mm thick, non skid, acid and scratch resistance over 15mm thick screed bed in CM 1:4 as in floor, set, jointed in neat cement sluury complete all as specified and as directed

M&L Joint free Non Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exc 0.06 and n.exc 0.11 Sqm in floors etc over 15mm screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed

M&L for Glazed coloured ceramic tiles in vertical surface 300x450mmx 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in cement mortat 1:4 complete all as specified and as directed

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for.

M& L PCC type C-2 1 :3 : 6 (40mm graded agg) in foundation, filling and mass concrete all as specified and directed.

M&L Cement concrete 1:2:4 type B2 (using 40mm graded aggregate) in surface channels and drain complete all as specified and directed.

M&L for forming fair finishes drain or channel 30 cm inner girth in cement concrete using extra cement all as specified and directed.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coping complete all as specified

Demolition of Brickwork or stone/boulders masonry built in cement mortar complete all as specified and as directed by the Engr-in-charge

M&L for precast cement concrete type C1 1:3:6 (using 20mm graded aggregate) block masonry with soild block, exc 10cm width and setting in cement mortor 1:6 complete all as specified and as directed

Taking down cement plaster on Brick or concrete surfaces incl racking out joints hacking for key scrubbing down with water etc complete

M & L rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finishing even and smooth without using extra cement complete all as specified and as directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for

M & L for providing precast cement concrete Type B-1 (20 mm graded aggregate) 1:2:4 as in cover slabs shelves and similar articles with plane faces set in cement mortar 1:6 complete all as specified and directed

M & L mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking , bending spirally for hooping ends and binding with and incl mild steel wire (annelaed) not less than 0.90mm dia or securing with clips

Dismatling of 300mm Reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches, if reqd

S&F Reinforced concrete pipes, class NP2, 300 mm bore, laid and jointed with cement mortar 1:1 completewith collars all as specified

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/blankets, any thickness, including cover fillets all as specified and as directed

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in secction in framed work, in any position complete all as specfied and as directed

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm in square, rectangular or traingular in section, clean sawn secured with nails or brads complete all as specified and directed

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 6 Sqcm but not exceeding 13 Sqcm in square, rectangular or traingular in section, bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed

S&F 12 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work complete, all as specified and directed

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work complete all as specified and directed

M&L for 6 mm thick plywood, 5 Nos of ply, grade BWP, type BB fixed with nails timber frame-work as in ceiling complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed

S&F 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with self tapping screw or L-type or J-type or crancked hook bolts and washers as in roofs, walls etc, with grade of zinc coating 275, complete all as specified and directed

All as per item No-36 here-in-before but except sheet

S&F Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete all as specified and directed

S & F 2mm thick fibre glass reinforced translucent corruggated sheeting with two corrugations side lap fixed with with self tapping screw or L-type or J-type or cranked hook bolts as in roof, wall etc complete all as specified and as directed

M&L Fe 290 (Gde E-165) for roof trussed (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed

M&L prepation of new or previously untreated surfaces of steel and applying two coat of Synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge

M&L for preparation of old surfaces of steel and applying two coat of Synthetic enamel paint complete all as specified and as directed

M&L for preparation of wood and wood based material surface of any descriptiony description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

M&L for prepration of old painted surface of wood and wood based material and one coat of synthetic enamel paint of any description, not otherwise described over 10cm width or girth complete all as specified and as directed

Note : Deduction for amount of Rs 16,506.00 as listed in Schedule A Part - II ( Schedule of Credit) shall be made while awarding of contract.

M/S DUTTA ENGINEERING WORKS