CA NO.CWE BLY/GE (E)/49 OF 2025- 2026PROVN OF TOILET IN WEST BLOCK AND RAM LEELA MAIDAAN AT RTS and DEPOT HEMPUR UNDER GE EAST BAREILLY

Surface dressing n exc 15 cm deep complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in any type of soil completed all as specified and directed.

Returning fillng in, including spreading , levelling , watering and well ramming in layers not exc 25cm complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.50M above the starting point complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, floors etc complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (Nominal Mix) (using 20mm graded stone aggregate) as in foundation footing, Plinth, lintel / roof beam complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (Nominal Mix) (using 20mm graded stone aggregate) columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (Nominal Mix) (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs complete all as specified and directed.

M&L for mild steel TMT bar 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed.

M&L for mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed.

M&L for form work to sides of concrete, foundation,footings base of columns,raft and raft beams,sides and soffits (if any) of foundation and plinth beams and similar work vertical or to butter complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beam, beam hings, girders bressume, lintles, contilevers, shelves including support over lungs etc also splays between floor and beams etc. complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for fly ash brick work with old size briccks having crushing strngth not less than 75kg/sqcm, straight or curved on plan bricks built in cement mortar 1:6 complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on fair faces of brick wall surfaces finished fair & even without using extra cement complete all as specified and directed

M&L for rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceilings finished even and smooth without using extra cement complete all as specified and directed.

M&L for hard core broken brick gauge n exc 63mm, deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm PCC 1:4:8 type D-2(40 mm graded stone aggregate ) as in floor complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L for Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for 7 to 8 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile area (300x450/300x600 mm size approved by GE), as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for machine pressed cement Concrete factory made coloured glazed interlocking paver blocks any shape and size confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade. machine pressed pattern and colour as approved by GE.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate)as in plinth protection finished even and smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 metres and every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete with and including necessary form work etc complete all as specified and directed.

S&F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.