Addn/ Altn to officer Accn Bldg No P-43 on Beacher road, Provn of bathing and washing shed at Bldg No T-20 Beacher road at Anarwala, Side covers/ false ceiling of shed at officer mess bldg No T-20 Beacher road, electric water heater to Md Accn of RI

Amount

Surface excavation in any type of soil (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavating in trenches in any type of soil , n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, UG Cable etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out complete all as specified

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified .

M & L for Hardcore of broken sotne/ boulders of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for hardcore of broken sotne/ boulders of gauge exc 63 mm but n.exc 100 mm deposited, spread and leveled in layers n.exc 15 cm thick, watered and rammed to a true surfaces complete all as specified and as directed.

M&L for Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass-concrete complete all as specified

M&L for 100mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub floor etc complete all as specified and directed

M&L for 25 mm thick cement concrete in 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in floor / sub floor complete all as specified and directed

M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified

M & L for RCC 1:1.5:3 nominal mix type A-1 { using 20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc and mass concrete complete all as specified and directed by Engineer-in-Charge

M&L for RCC 1:1.5:3 nominal mix type A-1 { using 20 mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed by Engineer-in-Charge

M&L for RCC 1:1.5:3 nominal mix type A-1 { using 20 mm graded stone aggregate) in beams,cantilevers,wall bends, bressummers, lintels over 1.5m span complete all as specified.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in kitchen slab, slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like, including demolition of exiting reinforced cement concrete complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in kitchen slab, slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

All as per item no 21 here-in-above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified.

S&F mild steel TMT bar 08 mm dia, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia as specified .

M&L for Formwork to sides of concrete foundations, footings, bases of columns, columns,raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces of concrete complete all as specified.

M&L for Formwork to sides and soffits of floor or roof beams, wall bend beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete Complete all as specified

M&L for Formwork flat fair finished to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and openingcomplete all as specified.

M&L for formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar works, not exceeding 200mm thick for fair finished surfaces of concrete complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in 1:6 using old size bricks complete all as specified

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in1:4 using old size bricks complete all as specified.

M &L 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specifeid

M&L for two coats of cement base paint over a coat of primer including preparation of new surface, complete all as specified and as directed by Engr-in-Charge.

M&L for 3 coats of white wash on walls including preparation of new surfaces complete all as specified and as directed .

M&L for preparation of wall and applying interior grade wall care putty 1 to 1.5 mm thick to make the surface smooth complete all as specified and directed by Engr-in-Charge.

M&L for preparation of wall and applying exterior grade wall care putty 1 to 1.5 mm thick to make the surface smooth complete all as specified and directed by Engr-in-Charge

M&L for two coat of oil bound distemper on already prepared / putty surfaces complete all as specified and directed.

M&L two coats of 1st quality exterior emulsion weather coat paints over a coat of alkaliresistant priming paint on already prepared or putty surface complete all as specified and directed.

M&L for coloured digital ceramic tiles in vertical surface as in walls, dado, etc of size 375 x 250 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified.

M&L for Vitrified Ceramic tiles Dark shed /double charged 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. over and including screed bed 15 mm thick in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile including dismantling old tiles complete all as specified

All as per item No 39 here-in-above but as in skirting/dado over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified..

M&L non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x 6- 7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match complete all as specified.

M&L for coloured Glazed ceramic designer tiles in vertical surfaces of size 350mm x 250mm x 7mm/ 450x 350 x 7mm thick over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as directed.

M & L for 75mm thk PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection, finished even and fair without using extra cement. The plinth protection shall be laid in alternate bays nexe 2 sqm with 10mm wide joints filled with bitumen mastic comprising of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified.

M&L for marble stone (makrana white) 18 to 20mm thick (table rubbed and polished) fixed as in steps, jambs, pillars, window cills, cooking plateform and the like set and jointed in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of slab including grinding, rubbing and polishing to mirror finish and exposed edges rounded with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 as in frame work for sun shade, roof projection etc. complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, staging for water tanks, gusset plates etc. conforming Fe-290 (Gde E-165) complete all as specified and as directed.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls/chajja covering etc fixed with self tapping screws as specified

S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof ridge /covering/ cladding to wall, fixed with self tapping screws as specified.

S&F false ceiling Perforated Accoustic GYP board tile Ivory painted (High pressure steam cured) of 6mm thickness (as per IS: 14862) of size 595 x 595 mm and any one of the design (Ocean, lake & hill, cascade or electra ) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15 x 32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15 x 32 mm made of 0.30 mm sheet, 1200 mm long spaced between main "T" at 600 mm c/c to form a grid of 1200 x 600 mm and secondary cross "T" of length 600 mm and size 15 x 32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200 x 600 mm panel to form grids of 600 x 600 mm and wall angle of size 15 x 20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making , opening for services like diffusers, grills, light fittings, fixture, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3 mm dia with galvanised butterfly level clips, spaced at 1200 mm c/c along centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/Sqm, including refixing of any type of wire/ wiring complete all as specified and as directed by Engr-in-Charge.

Providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width all complete at all heights as per direction of Engineer-in-Charge. form a grid of

S&F pressed steel frames of 125x60mm size for door with one or more rebates including necessary fixing lugs, hinges lock strick plate etc. including filling of PCC 1:3:6 type C-0 complete all as specified & directed.

S&F flush shutters 30 mm thick one face is covered with decorative face veneer teak wood finished with lipping/frame to match , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 30mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube as specified in SSR Part-II complete all as specified and directed.

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as shown in SSR Part – II 2010 and as directed by GE/Engineer-in-Charge. Make : “Syntex/ Rajshree Plastic wood Forex ”, ECHON.

S&F for powder coated aluminium window/ventilator fixed type with provision movable slanting glass 75 mm wide stripps / half glazed and half gauged with and including hardware fitting, glazing, wire gauge, rubber packing, aluminium beading etc, complete all as specified and directed :- aluminium section shall be of size as given below: Frame:- 100 x 44.45 x 1.5mm/44.5x44.5mmx 1.08mm thick, Top/ botton rails and middle / side styles of shutter -100 x 44.45 x 1.5mm/ 44.5x 44.5 mm x 1.08 mm thick Including Glass: 5 mm thick frosted glass fixed with rubber gasket with aluminium beading, necessary aluminium beading,SS wire gauge complete all as specified and directed.

S&F factory fabricated steel window with side hung shutter ( double shutter) external shutter shall be provided glazing bar and internal shutter shall be without glazing bar ( mosquito proofing) steel window provided with box type hinges, guard bar/grill 10mm square bar shall be provided in external frame, 2 nos peg stay shall be provide with external shutter, 2 nos MS handle shall be provide each shutter, steel window shall be provide with soap coat painting before fixing, all welding shall be flush butt welded, steel window shall be procured from IS approved manufacture, including taking down old steel window complete all as specified and directed. Note :-Sample and design of steel window shall be approved by Garrison Engineer .

S & F factory made steel window with side hung shutters including projecting/box/pin type hinges with steel handle, steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F factory made steel window with side hung shutters including projecting/box/pin type hinges with steel handle, steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 150 mm long Aluminium anodised handles of fabricated type complete all as specified and as directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel 202 grade bright finish barrel tower bolts 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel 202 grade bright finish barrel tower bolts 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150mm size solid in one piece stainless steel 202 grade bright finish handles, D type and fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F 125mm size solid in one piece stainless steel 202 grade bright finish handles, D type and fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F 100 mm size stainless steel butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified

S & F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy & fixed and compete all as specified and directed.

S&F Floor door stopper of Aluminium alloy body double spring and tongue, overall length of cover plate 150 mm , anodized, with hard drawn steel spring , fixed to shutters complete all as specified and as directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified

M&L for preparation of newly steel Surfaces of any description, over 10cm width or grith, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for preparation of new wooden surface of any description over 10 cm width or grith not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified

S&F 18mm thick fiber reinforecment plastic (FRP) sheet of both side pre laminated colour 3mm laminated on both faces (3mm+12mm+3mm) and esges to be seald with (PVC) edges binding tape with matching colour to make kitchen cabinet shutter/ drawer front, cup board shutter, etc complete all as specified and as directed.

S&F 6 mm thick WPC board one side prelaminated and other side plain white colour as in cup board/shelves, fixed with screws , solvent cement/ashesive complete all as specified and directed.Make : Rajshri/ECHON/Alstone

S & F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all specified and directed

S&F magnet catcher for cub board with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F Hasp and staple 100mm safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws

S&F stainless steel handle fency type 100 mm size for kitchen cabinet shutters complete all as specified and directed.Make : Hexa/Hettich/Hafele

S&F 20mm dia brass chromium plated tubular towel rails fancy, D type, 60cm long between flanges, complete all as specified.

S&F glass corner shelf suitable size made of 5mm thick toughned glass complete all as specified.

S&F Stainless steel shelf 40 cm size fixed with and including chromium plated brass screws and wooden/plastic cleats. complete all asspecified.

S&F 25 mm dia stainless steel polished 204 grade drapery rod 1mm thick with final decorative, including brackets, decorative nobs at both ends complete all as specified and directed as per approved sample. (Make-Vista or equivalent as approved by GE)

S&F 300mm long MS Helical door spring welded to steel frame or fixed to wooden door frame with screws including roller and roller plate etc complete all as specified and directed.

S&F 5mm thick Fancy type looking mirror fixed to wall with teakwood beading complete all as specified and directed by Engr-in-charge Make : Modiguard/Sant Gobian and Cera eqivalent

S&F stainless steel hanger (min 5 Nos of hooks) fixed on CP plate 40mm wide including fixing screw as per approved sample complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in brick work making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified

S&F vitreous chinaware wash down water closet pan (Padestal pattern) fancy type including fixing bolt, flushing cistern, Dual flush single piece EWC with soft close seat cover fittings 'P' or 'S' trap complete all as specified and dircted..

S&F 15mm bore Bib taps long body, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make :- JAGUAR CAT Part No ALI-85037/Hindweare CAT Part No F-370004/Prayag CAT Part No S9906

S&F CP brass bib tap fancy type short body15mm bore screwed for iron pipe or for brass ferrule all as specified in SSR Part I . Make : Jaquar product code: EKO-CHR-33037 or equivalent in Hindware/ Prayag.

S&F concealed stop cock, fancy type, brass chromium plated with round heeaded knob suitable for 15mm bore iron pipe, complete all as specified.

S & F Chromium Plated brass soap dish fixed to wall with chromium plated brass screwed and cup washer complete all as specified and directed.

S&F chromium plated stop valves/ angle valve etc, cast copper alloy, screwed down both high pressure, with crutch or butterfly handle, screwed both ends fixed, 15mm bore complete all as specified

S&F in repair 15mm nominal internal bore PVC connection 450mm long with two brass nuts and PVC washer complete all as specifed

Supply only PVC connection 15 mm dia 450 to 600 mm long with brass fly nut at both ends complete

S&F vitreous china wash hand basin including padestal, white flat back, size 580x450mm including brackets, waste pipe, CP waste couplingetc complete all as specified

S&F Vitreous China wash hand basin, white, flat back type of size 550mm x 400 mm fixed on and including cast iron cantilever bracket, 32 mm dia brass waste coupling and 32 mm dia PVC waste pipe, grating dome, etc complete all as specified.

S&F CP Brass 3 in 1 hot & cold 15 mm dia wall mixer for mixing hot & cold water with telephonic shower provn with connecting legs & flanges complete all as specified and directed. Make : Jaquar Model No CON 281KN, HSH 1929 & OHS 1989 or equivalent in Hindware / parryware.

S&F 15mm dia swan neck pillar tap (for oval type WHB) brass chromium plated with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, and fixed complete all as specified and as directed by Engr-in-Charge.

S & F 15 mm dia CP brass centre hole basin mixer (pillar tap) with accessories in wash basin for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed.

S&F brass chromium plated ovehead fancy shower with shower arm complete all as specified and directed.

S&F 15mm bore chromium plated fancy type Two way bib tap of cast copper alloy with crutch of butterfly handle, screwed in iron pipe complete all as specified

S&F CP Health Faucet with 1.20 mtr metalic Expandable tube & hook complete all as specified and directed and approved by Engr-in-Charge.

S&F PVC waste pipe not less than 60 cm long with PVC coupler for kitchen sink , WHB , Urinal etc complete all as specified and directed.

S&F 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20 mm brass float valve with pvc ball complete all as specified

S & F 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall/floor/trenches etc complete all as specified.

S & F 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall/floor/trenches etc complete all as specified.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, drain and manholes complete all as specified and as directed.

M&L for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

M&L PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

M&L for 75mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone agg) as in floor etc and finished the top surface of concrete by brooming complete all as specified and directed.

M&L for heavy duty Skid proof vitrified designer coloured tile area of each tile not exe 0.36 sqm,10mm thick dark shed exterior grade (square/rectangular) in floor, parking, path etc, jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement morter 1:6 and dismantling of existing floor tiling including cement morter bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L factory made prepolished rubber moulded vibromatic Chequred cement concrete tiles 30cmx30cmx20-22mm thick, set jointed and pointed in neat cement slurry with grey cement and colour pigment to match over and including 15mm thick screed bedding layer in CM (1:6) complete all as specified.

M&L for concrete in PCC (1:3:6) type C-2 ( using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed .

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 150 mm Internal dia, grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 complete

M&L for construction of brick masonry soakage well, internal dia 2.40M dia & 3 mtr depth including excavation in any type of soil complete all as specified and shown on TD drawing & directed.

Cutting into existing manholes/septic tank for connecting new drains 150mm bore pipe including removing existing branch drain pipes of 100/150mm bore & benching to form branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) surface finished and reforming benching as required and making good surface with plaster etc to match existing , etc complete all as specified and directed.

M&L for providing damp proof course 40 mm thick in cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) to horizontal or vertical surfaces mixed with integral water proofing compound as per manufacturere instructions including necessary formwork complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid seperately.

M&L for precast reinforced cement concrete (1:1.5:3) type A-1 (using 20mm graded stone aggregate) as in landings, cover slabs ( for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary form work, set in cement mortar 1:6 complete all as specified and directed. (Reinforcement shall be measured and paid for separately under respective item of schedule 'A')

M&L for moorum/red bajari filling in floors or pavings, laid in layers n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone agg as in sub base complete all as specified and as directed by the Engr-in-Charge.

M&L for screed bed bedding 15 mm thick in cement mortar (1:6) for floor laying floor finish complete all as specified and as directed .

S & F 3.0 mm thick plain sheet glass, ordinary quality and glazing with oil putty or wooden beads in square n exc 0.5 Sqm in each pane and complete all as specified and directed.

S & F for mild steel framed work such as door frames, grills, gratings, etc, with ends of bars shouldered and / or riveted or forged into spikes; framed guard bars; frame work of water tanks and similar work confirming to Fe-290 Gde-E-165 including necessary welding, drilling hole complete all as specified and directed

Supplying, fixing, jointing and testing galvanised steel water tubing 15 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

Supplying, fixing, jointing and testing galvanised steel water tubing 20 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F Vitreous China Urinals, half stall type white (back or corner wall type), complete including providing and fixing plugs, bedding urinals against wall in CM 1:2, securing urinals to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, CP waste coupling, waste pipe, automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete. complete all as specified and as directed by Engr-in-Charge.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) water closet, including 600 mm long CI P-trap, connection to trap and to flushing pipe, anti syphonage pipe etc, and making good to floor complete all as specified and as directed by Engr-in-Charge.

S & F 10 litres capacity PVC low level valve less syphonic action type flushing cistern white with inlet, float valve, float and handle including brackets with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed by Engr-in-Charge.

Supply & fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size complete all as specified.

S&F 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

S & F PVC (SWR) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 75 mm dia bore of pipe complete all as specified and directed.

S & F PVC (SWR) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 110 mm dia bore of pipe complete all as specified and directed.

S & F PVC (SWR) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 75 mm dia pipe complete all as specified and directed.

S & F PVC (SWR) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe complete all as specified and directed.

S & F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F aluminum alloy powder coated door made out of hollow extruded aluminum section as mentioned below. Each door having 02 Nos Disc or D type handle, 02 Nos aluminum tower bolt 200 mm size, one brass mortice lock of six lever with key in duplicate regulated by double action hydraulic floor spring heavy duty (Make:- Sandhu/Ritz) shutter to be partly glaze with 5mm thick tined coloured glass in upper pannel and partly pannelled with 12mm thick both side laminated particle board in lower pannel fixed with glazing clip, rubber beading/gasket, anodised aluminum beading screw complete all as specified and directed at site. Chowkhat Frame:- 101.60x44.45x1.60mm Shutter verticle style :- 85x44.45x1.56mm shutter middle Rail :- 83.50x44.45x1.54mm Shutter Top Rail and bottom Rail :- 114.30x44.45x1.55mm Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

S&F powder coated Aluminium partition (Fixed) made out of aluminium powder coated section 83 x 44.45 x 2.00 mm including 5 mm thick glass/ACP Sheet complete with rubber packing/aluminum beading etc including dismantling of exixting structure complete all as specified and directed. Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

S&F aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one nos wire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows, and glazed with tinted glass coloured glass 4mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long etc complete all as specified and directed. Shutter Top & bottom size : 37.50x15x1.60mm Shutter inner lock size 37.50x15x1.60 mm Shutter side (Handle) size 37.50x15x1.36 mm Chowkhat bottom size : 50.30x26x1.20mm Chowkhat top & sides size: 50.30x26x1.00mm Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

M&L rendering 15 mm thick with WPC on parapet,chajja, facia,celing etc in CM 1:3 and finished even and smooth (with out using extra cement) on external surfaces including two coat of whether proof exterior emulsion paint over a priming coat including taking down of plaster any description complete all as specified and directed. Note : 1.Water proofing compound shall be measured and paid separately as supply only. 2. Cost of scafolding for rendering is included in the quoted rate of item.

M&L for water proofing treatment with fiber reinforced elastomeric liquid applied on roof slab/chajja/perapet including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment ,damp proof described as under:- (a) Preparation of surface, filling of cracks with Smart care Hybrid PU Sealant wherever required. (b) Providing PCC (1:2:4) type B-0, 25mm thick screed bed or bedding layer over roof surface . (c) Providing and applying smartcare Damp proof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinfocing acrylic fibers having sun reflectivity index (SRI) of 105 on top of concrete roof in three coats @ 10.76 litre/10sqm. one coat of self- priming of elastomeric waterproofing liquis (dilution with water in the ratio of 1:3) and two coats of undiluted elastomeric waterproofing liquid (dry flim thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer -in - charge . when the 2nd coat is wet, the smartcare EPDM tape (at corners and edges) shall be inserted of smartcare Damp proof shall be continued to the parapet wall/chajja/facia etc to better envelope the whole area. The coating shall be terminate carefully to the other side of the parapet/chajja/facia.Make: Asian Paint Smart care or equalvent. Execution to be done with authorised applicator of the manufacturer. Work will be executed in smart assurance system. Note : The work will be carried out upto double storey builing the rate of scafolding is included for this item also and dismantling of existing water tank and re fixing same position after work complete.

M&L for two coats of Damp proof PU Paint on plastered surface of roof etc complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed.

M&L two coat weather coat exerior emulsion paint/ Apex ultima paint any tint over a coat of primer on walls complete all as specified in SSR Part I including complete removal of old existing treatment from wall upto plaster surface by electric sand paper grinder, washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper all as directed by Engr-in-charge. Make : Berger/Asian/Shalimar Note : The work will be carried out upto double storey builing (ii) The rate of scafolding is included in the quoted rate of item.

M&L for preparation of old decorated surfaces of walls (plastered) by brooming down with steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and finally clean with sand paper /electric sand paper grinder,all as directed by Engr-in-Charge.

M&L two coat oil bound distemper by roller of any tint over a coat of primer on already prepared / putty surface walls complete all as specified in SSR Part I including complete all as directed by Engr-in-charge.

S&F MCB SPN 240 Volt 10 KA 40 Amp conforming to IS complete all as specified

Supply and fix electric water heater, storage type steel body with glass lined SS inner tank and efficiant long life heating element upto 2 KW, Capacity 25 litre, Shock -resistance ABS outer body,tank design suitable to with stand 8 bar pressure complete with all accessories such as safety valve, thermostate, NRV, nylon braided PVC flexible connection pipes,15 mmdia,450 mm long with check nut & washers for Hot Cold water, fire retardent 3 core copper cable ,ISI Marked complete fixing with suitable size of fixing arrangement all as specified and directed by Engr -in -charge Make : Recold model no CDR 25V/equivalent in Bajaj /Havells

Supply and fixing in replacement for Distribution Box MCB Protected Socket with sheet steel enclosure 20 A MCB DBOXX Combo DP including PLUG TOP all as specified & directed Make : Havells/LEGRAND/L&T

S&F MCB ,SP,25 Amp,10 KA,B-Siries,230V accomodated in Existing DB with suitable lugs all as specified & directed. Make ; Legrand/L&T/ABB

S&F CP bib cock cast copper alloy with crutch handle screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified. Make :zalooto/prayag/ceria

Supply and laying under ground cable, nominal cross sectional area 10 Sqmm, 4 core,1100 Volts grade, XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.

Supply and laying under ground cable, nominal cross sectional area 10 Sqmm, 2 core,1100 Volts grade, XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.

Supply and laying under ground cable, nominal cross sectional area 95 Sqmm, 3½ core,1100 Volts grade, XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.

M&L Sand cushioning and covering of UG cable using crushed metal sand in trenches for cable protection all as specified and directed.

M&L for bricks well burnt Class ‘B’ as cover to U/G cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches all as specified and directed by Engineer-in-Charge.

Cutting existing road/hardstand of any type by using crow bar chisel uprto a depthof 30 cm for laying GI pipe including making good the surface by returning filling watering ramming in layers 150 mm thick PCC 1:2:4 over 200 mm thick hard core of broken bricks/stones over returning filling watering ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engineer-in-Charge.

Supply, transporting, erection and fixing steel tubular pole, 8.5 metres long, type 410 SP-31, complete with MS base plate 6 mm thick, plug at top cap, finial taper plug, bolts, nuts, washers etc including painting two coats of aluminium paint over one coat of red oxide primer including 3 nos band/straps with red post office box colour (300mm wide each) synthetic enamelled paint at a distance 300mm from plinth block and marking pole nos with black synthetic enamelled paint including tarring one coat on steel surface embedded in concrete complete all as specified and directed. NOTE:- Excavation, Earthwork and PCC work shall be measured and paid seperately

S&F junction box made of glass fibre reinforced and transparent poly carbonate of size 126x228x111, KV PC 8104 with IP 65 protection including MCB SP, 6 Amps 1 No and suitable size clamps fixing for pole/in pcc foundation etc,including taking down the old one,all as specified and as directed. Make :-Hensel / L&T/ Legrand

S&F LED flood light 70W including integrated driver, IP-65/66 alluminium extruded body, power coated including fixing arrangement like clamps, nuts bolts and washer complete all as specified and directed .

Supply, install, Testing & commissioning of Voltage stabilizer for automatic operation, three phase naturally oil cooled indoor type & designed for input variation between 340 V to 460 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity of capacity 20 KVA , Features Latest Digital Microprocessor Controller, High quality raw material, High efficiency, Saves power and Reduces MDI, Long life with negligible maintenance complete all as specified and directed. Make : Servo / Microtek / V -Guard as approved by GE.

M&L for GI Tubing Light grade (ISI marked) with all fitting/acessories for protection of cable on pole/wall and under road crossing including clamps, nut bolt etc all as specified and directed of size 50mm dia (make: prakash surya/jindal/TATA)

M&L for copper earthing complete with Copper earth plate electrode 60cm x 60cm x 3.15mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to Copper earth strip 20x3mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of (0.68mm) 8 mesh per liner inch, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I and specified including provision of earth wire protected by 40mm dia medium grade GI pipe and watering pipe shall be 20mm bore medium grade GI pipe, and including all excavation and earth work & connecting the earthing to an earthing test point /transformer nuetral/body/ Lt panel etc. and testing on completion, complete all as specified & directed

Taking down carefully existing aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc ( light, fan, socket, or power and switch, socket, regulator, holders, ceiling roses) complete and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing all as specified and directed.

M & L for point wiring complete with PVC insulated and unsheathed, FRLS 1100 volt grade electric cable of size 3 run x 1.5 sqmm (Phase+Neutral+Earth with colour coding as per IE Rules) , multi stranded copper conductor single core in and drawing through exisitng conduit (without socket, elbow, junction box, bell mouth, bend, reducer) not less than 19 mm dia, clip, complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including MS Box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, complete all as specified including lugs required for One light/fan point controlled by one switch , complete all as specified and directed. Note :- Modular switches boxes and cover plates shall be measured and paid separately

All as per item No 168 here-in-above but point wiring for one 5 pin 5 Amp socket outlet point on same board complete all as specified

All as per item No 168 here-in-above but for one 5 pin 5 Amp socket outlet point on independent board complete all as specified and directed.

All as per item No 168 here in before but with 4 Sqmm cables for one 6 pin 15 Amp socket outlet point on independent board

S & F Modular Fan Regulator electronic rotary,0-4 steps step type 100 Watt, 240 Volt 50 Hz hum free 2 module complete all as specified and directed.

S&F Supply and fixing switch modular 6 Amps 230 Volts one way switch complete all as specified and directed.

S&F Socket modular 6 Amps AC 230 Volts 2/3 pin combined 2 modular type complete all as specified and as directed

S&F Socket 6A/16 Amps-2/3 pin combined AC 230 Volts modular type complete all as specified and as directed.

S&F Switch modular type AC 230 volts 16 Amps one way complete all as specified & as directed.

S&F moduler bell push 6 Amp one module one way complete all as specified.

S&F GI sunken box with flush metal GI box 1 module suitable for modular switches incl plastering, making good disturbed surfaces of wall, painting to match the existing finishes complete all as directed.

All as per item no 178 here in above but 2 module.

All as per item no 178 here in above but 3 module.

All as per item no 178 here in above but 4 module.

All as per item no 178 here in above but 6 module.

All as per item no 178 here in above but 8 module.

S&F combind cover plate white 1 module suitable for modular switches complete all as specified and directed.

All as per item no 184 here in above but 2 module

All as per item no 184 here in above but 3 module

All as per item no 184 here in above but 4 module

All as per item no 184 here in above but 6 module

All as per item no 184 here in above but 8 module

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with LED lamp 9/10 watt complete all as specified & directed.

S & F sheet metal enclosure SPN for DB's when MCB's to be used 12 way with 200 amps bus bar and double door complete all as specified and directed.

All as per item no 192 here in above but DB' 8 way complete all as specified and directed.

S&F metal clad single pole and neutral enclosure with 2 pin and earth plug and socket complete with and including one single pole MCB 20 Amp 240Volt complete all as specified and directed.

S&F MCB SPN 240 Volt 10 KA 6 to 40 Amp 'C' series conforming to IS complete all as specified & directed.

S&F MCB SP(single pole) 240 volt, 10 KA, 6-40 Amp, 'C' series confirming to IS complete all as specified and directed.

S&F MCB single pole and neutral 240 volts, 25 to 40 Amps complete all as specified and directed.

S&F MCB single pole 240 volts, 6 to 32 Amps all as specified and directed.

M&L for sub main wiring with 3 Runs (N+P+E) of 4 sqmm single core PVC insulated copper cable unsheathed 1100 volt grade, colour coding as per IE rules drawing through and including concealed conduit with accessor ies complete all as specified and directed. Note - 3 run of 4 sqmm cable and 1 run of PVC conduit shall be measured as one unit length.

Taking down carefully sub main wiring of any description and in any position and removing from site complete all as specified and directed.

All as per item no 199 here-in-above but sub main wiring with 2.5 sqmm copper cable drawing through surface conduit Note:-3 runs of 2.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 201 here in above but with 6 Sqmm (nominal area) drawing in and including 25 mm dia or higher medium duty PVC concealed conduit

M&L point wiring with 1.5 Sqmm (Nominal area) PVC insulated and unsheathed single core cable 1100 Volts grade with stranded copper conductor in and including PVC casing and caping including accessories along with continuous earth wire 1.5 Sqmm PVC insulated, unsheathed stranded copper conductor cable and connected to common earth dolly, with and including 1.6 mm thick cadmium plated sunk MS pressed steel terminal boxes with 3.0 mm thick hylum sheet cover fixed with brass screw complete with all accessories for one light point/Fan point controlled by one ,one way switch.

One light/fan point controlled by one switch.

One 5 pin socket outlet 5 Amps controlled with one switch on the same board.

One 5 pin socket outlet 5 Amp controlled by one switch on independent board.

All as per item No 203 here-in-before but with 2.5 sqmm multistrand copper conductor cable for one 15 Amp socket outlet controlled by one switch on independent board and 1.5 sqmm PVC insulated multi strand copper conductor cable as continous earth wire complete.

S&F Switch piano flush button single pole one way 5 Amp complete all as specified.

S&F Socket outlet, 5 Pin, 6 Amp 2 in 1, flush type, universal complete all as specified.

S&F Socket outlet 2 in 1, 5 pin, 5 and 15 Amp flush type complete all as specified

S&F Switch piano flush button single pole one way 15 Amp complete all as specified

S&F Fan regulator stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as reqd.

M & L point wiring with 2.5 sq mm copper conductor (multistranded), FRLS , single core PVC insulated, unsheathed, 1100 volt grade cable and incl PVC casing and capping with all accessories and terminated in PVC moulded box, duly earthed with PVC insulated 2.5 sq mm copper conductor cable in green colour for earth continuity conductor to earth dolly complete as specified for item No -2 all as specified and directed by Engineer in Charge.

S&F Ultra bright LED Tubelight fitting of LED 20 w incluing reqd length of 1.5 Sqmm PVC multistranded copper conductor ro electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25m deep below normal ground level with top edge of plate not less than 1.5 m below normal ground level connected to galvanized wire 4 mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanized iron pipe 15 mm bore (light grade) including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm dia MS bar funnel wire mesh 20 mm bore galvanized iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR part 1 including testing on completion all as specified and directed. incl demolition to existing one complete.

Supply & fix ceiling fan 1200mm sweep, 230 Volts AC single phase, 50 Hz 3 blades, double ball bearing, energy saving complete with and including three core flexible PVC insulated multi stranded copper conductor cable of size 0.5 sqmm from ceiling rose to connector, including extra GI/MS pipe down rod, as per site requirement complete all as specified and directed. Make : Havells/Bajaj/Orient as approved by GE.

S&F PVC connection pipe (suitable to cold water) of 15 mm dia, 450 mm long with two brass CP hexagonal nuts adopter rubber washer.

S&F PVC connection pipe (suitable to Hot water) of 15 mm dia 450 mm long with brass flexible tube alongwith CP Hexagonal nuts adopter rubebr washer.

M/S C S AITHANI